Home

Instek GRS-6052A and GRS-6032A Manual

Contents

1. Set the cursor position TEXT ILLUM etc by turning or pressing the VARIABLE knob In the cursor mode pressing the VARIABLE control knob to select the cursor position between FINE and COARSE adjustment When select FINE adjustment by turning the VARIABLE the cursor lines will move slowly If select COARSE adjustment he cursor will move fast In TEXT ILLUM mode this control knob can be used to set the text intensity or illumination Please refer to TEXT ILLUM 7 for details Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 10 SAVE RECALL P The instrument contains 10 non volatile memories which can be used by the operator to save instrument setting and to recall them It relates to all controls which are electronically selected Press Jor PP pushbutton to select the memory location The readout then indicates the letter M followed by a cipher between 0 and 9 Each time the W pushbutton is briefly pressed the memory location cipher increases until the number 9 is reached The Q pushbutton is similar but decreases the memory location cipher until the number 0 is reached Pressing and holding SAVE for approx 3 seconds to write the instrument settings in the memory and indicate the associated readout information of To recall a front panel setup select a memory location as described above Recall the settings by pressing and ho
2. polarity CHI VERT 20Hz SMHz 0 5 DI 2 0 DIV 200mV S5MHz 40MHz 1 5 DIV 3 0 DIV 800mV Vv i 10MB 50MEz Pee CHI VERT Trigger Sensitivity GRS 6032 CH2 MODE 20Hz 2MHz 2 0 DIV 2MHz 20MHz 20MHz 30MHz TV sync pulse more than 1 DIV CH1 CH2 VERT MODE or 200mV EXT Input impedance Approx IM Q 25pF AC External Trigger Input coupling Max input voltage 400V DC AC peak at IkHz Hold off Time Variable Real Time Mode only X Y Input X axis CHI Y axis CH2 OPERATION Sensitivity HmV DIV 20V DIV REAL TIME Bandwidth X axis DC 500kHz 3dB mode Phase Difference 3 or less from DC to 50kHz 6 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Acquisition Digitizer 8 bit ADC x 2 500MS s for equivalent time sampling 20MS s for normal sampling Single shot DC to SMHz Repetitive DC to SOMHz GRS 6052 DC to 30MHz GRS 6032 Max Sampling Rate Storage Bandwidth 3dB Dynamic Range SDIV Memory Length Acquisition Memory 2k words CH X 2 1k words CH equivalent Save REF Memory 1k words CH xX 10 with back up memory REF 0 9 Display Memory 1k words CH x 4 waveform max Equivalent 0 2 u s DIV 2 u s DIV Normal 5 u s DIV 0 1s DIV Roll Mode 0 2s DIV 100s DIV x5 X10 X20 STORAGE Max Sweep
3. ccccccecseesectecseenceneeeeceusassenseeness 13 A 2 Rear Panel sissssipicsinsnsasnososstirssnrsisediner seisan 32 5 OPERATION METHOD ccccecescersesccnseeesseacvonenes 34 5 1 Readout Display cccecseseceeseesecscneeneseseeeesses 34 5 2 Connecting Input Signals ceeeeseesseneeeesreeees 37 5 3 Adjustment and Checks ccssseecseeescecncecsevenseeees 38 5 4 Function Check cceccceccsccceesevensceneneceeceeseenes 40 5 5 Basic Operation csscscsessceceeenceeseceecereueeceseates 42 5 6 Digital Storage FUNCTIONS 0 eesecceereceseecceneces 51 5 7 Measurement Application 0 ssseseesseveessceteesenees 59 5 8 RS 232 Interface Remote Control ceseseerereees 61 6 MAINTENANCE 0 cccceeeeececeeeeeeeeesacetneeceneneeeeees 91 6 1 Fuse Replacement ccesessececeeeceseenesesesecnenese 91 6 2 Line Voltage Conversion ceeceeeeeneeecnneeneeeneees 91 6 3 CLEAMING os cscescicec ce sceeeacvssennacecaisansaenstseaneaeauecainean 92 7 BLOCK DIAGRAM ccecccecesecseeeecenteesecteneneeesneet 93 1 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL SAFETY TERMS AND SYMBOLS These terms may appear in this manual or on the product WARNING Warning statements identify condition or practices that could result in injury or loss of life CA
4. A rtisan Artisan Technology Group is your source for quality TecmoogyGroup new and certified used pre owned equipment FAST SHIPPING AND SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT DELIVERY Experienced engineers and technicians on staff Sell your excess underutilized and idle used equipment TENS OF THOUSANDS OF at our full service in house repair center We also offer credit for buy backs and trade ins IN STOCK ITEMS www artisantg com WeBuyEquipment 7 EQUIPMENT DEMOS HUNDREDS OF InstraV ea REMOTE INSPECTION LOOKING FOR MORE INFORMATION MANUFACTURERS Remotely inspect equipment before purchasing with Visit us on the web at www artisantg com 7 for more our interactive website at www instraview com information on price quotations drivers technical LEASING MONTHLY specifications manuals and documentation RENTALS ITAR CERTIFIED D a gaa tia Contact us 888 88 SOURCE sales artisantg com www artisantg com 50 30 MHz DIGITAL STORAGE OSCILLOSCOPE GRS 6052 6032 User Manual insTtex Good Will Instrument Co Ltd GW Part No 82RS 60520MA Printed in Taiwan May 2002 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com All Rights Reserved T
5. Figure 5 13 Alternate Trig a AG Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Triggering of Video signal In the work concerned with TV complex signals and containing video signal blanking pedestal signal and synchronizing signal are often measured Press the TV pushbutton to set the TV position The built in active TV Sync separator provides the separation of frame or line sync pulses from the video signal To trigger the oscilloscope at the vertical frame rate press the TV pushbutton to set TV V and TV H triggering The figure 5 14 a shows vertical signal of TV V and Figure 5 14 b shows horizontal signal of TV H Figure 5 14 a TV V Figure 5 14 b TV H The figure 5 15 shows the examples of TV polarity synchronization signals Note This oscilloscope synchronizes with only _J synchronizing signal REFERENCE Synchronizing signal i Video signal Video signal N Synchronizing signal Figure 5 15 TV Signal E ee Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL a a ar 5 6 Digital Storage Functions The operation procedure of the digital storage functions is described below Normal Sampling mode SMPL 1 Display the waveform to be stored in the REAL TIME mode 2
6. USER MANUAL DB9 to DB9 Wiring The wiring configuration is used for computer with DB9 connectors that configured as Data Terminal Equipment GRS 6052 6032 Computer DB9 DTE DB9 DTE Pin2 gt Pin2 Pin3 a gt Pin3 Pin5S e Pind Figure 5 21 DB9 to DB9 wiring When the GRS 6052 6032 is set up with a RS232 interface please check the following points Do not connect the output line of one DTE device to the output line of the other Many devices require a constant high signal on one or more input pins Ensure that the signal ground of the equipment is connected to the signal ground of the external device Ensure that the chassis ground of the equipment is connected to the chassis ground of the external device Do not use more than 15m of cable to connect devices to a PC Ensure the same configurations are used on the device as the one used on PC terminal Ensure the connector for the both side of cable and the internal connected line are met the demand of the instrument Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Communication Mode The same baud rate and data format must be set to the instrument and the computer The baud rate of the RS 232 interface can be set as listed in the following table 300 Baud 900 Baud 1200 Baud 2400 Baud 4800 Baud 9600 Baud The data transmission for
7. Parameter range gt 0 0 DIV to 500 L0DIV If Target B Parameter range gt 0 ODIV to 200 4 DIV Target A gt Pre B gt Post H VAR E wn a Parameters 3Bytes Sets or queries the horizontal VAR function Syntax H3 128 H3 Arguments Parameters 080 uncalibrated Max to 255 uncalibrated Min Enable horizontal VAR function and sets VAR value 000 calibrated gt Disable horizontal VAR function Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL XY Mode H 4 Parameters 3Bytes Sets or queries the XY mode Syntax H4 001 H4 Arguments Parameters 000 Disable XY mode 001 Enable XY mode Sweep Magnification H 5 Parameters 3Bytes Sets or queries the MAG function Syntax H5 002 H5 82 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL _ _ _ Arguments Parameters 000 MAG Disable 001 X5 002 X10 003 X20 Parameters 3Bytes Sets or queries the MAG ALT mode Syntax H6 001 H6 Arguments Parameters 000 Disable MAG ALT mode 001 Enable MAG ALT mode g 2 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com G
8. Press the STORAGE pushbutton switch and the RUN LED is on 3 In this mode a waveform is swept every trigger according to the setting state of controls on the front panel the waveform to be stored is displayed on the CRT as it is The slower the sweep rate the longer the time is required for the acquisition and display of the waveform It takes approximately 3 seconds until a waveform is acquired at the sweep range of 0 1s DIV The trigger signal is generated thereafter Therefore when the sweep rate is slow the waveform is not displayed on the CRT immediately after the controls on the front panel have been adjusted 4 When the TIME DIV control is from 5 u s DIV to 0 1s DIV both the single and the repetitive waveforms can be stored Equivalent Sampling Mode EQU When the TIME DIV control knob is set to 0 2 u s DIV to 2u s DIV 4 steps only the repetitive waveform can be stored in the equivalent sampling mode The first left end rising and falling edges of the traces may not be displayed in the repeat mode range In this case measure the rising or falling edge on the second or later cycles of the waveform It takes 5 seconds or more to store the input signal of 1kHz or lower When the low frequency signal is stored noise can be mixed It is recommended to use a sine wave of IMHz or higher or a square wave with the rise time which is faster than 0 3 u s Artisan Technology Group Quality Instrumentation Guaranteed 888
9. 3 A change in line voltage may also require a corresponding change of fuse value Install the correct fuse value as listed on rear panel 22973 e Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 6 3 Cleaning To clean the oscilloscope use a soft cloth dampened in a solution of mild detergent and water Do not spray cleaner directly onto the oscilloscope because it may leak into the cabinet and cause damage Do not use chemicals containing benzine benzene toluene xylene acetone or similar solvents Do not use abrasive cleaners on any portion of the oscilloscope 94 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 7 Block Diagram YOLVESNY o AWS gt UWO JAY JY YNOS ZHAWG dAS O WNOIS woe Now 33Na HOVI OL X LYYINIO ow W 1HO ONIHOLIAAS WINOZRIOH gt HOLS om ry 2001 aWvaud pene nD l UY ZHO D LANI A ZHI X dY AHON AER SIXY X OWL Pome IHD S Em zav e i LIY tHO WS LNdNI BR O tHO 95 Guaranteed 888 88 SOURCE www artisantg com Artisan Technology Group Quality Instrumentation Artisan Technology Group Quality Instrumentatio
10. 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL i a i Measure the rising and falling edges of the trace an and after the second cycle of the waveform First left end rising and falling edge of the trace can not be measured i Pe 2 _ _ Figure 5 16 ROLL mode The displayed waveform is rolled from right to left 0 2s DIV to 100s DIV The right end of each trace is the updating point of a new data The Roll mode facilitates the measurement of a signal of approximately 100Hz or lower Press the STOP switch to stop the ROLL mode and hold the final waveform on the CRT Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL a i Rolling direction 500S Hy ete HI i ER HH a old data Stored new data new data Figure 5 17 NOTE Aliasing While measuring the signal in such STORAGE mode as SMPL AVG etc the aliasing can be occurred by inputting a signal of more than half of the frequency with respect to the sample clock frequency at the sweeping range is added When the aliasing is occurred the waveform of the input signal frequency minus the sample clock frequency will be displayed It is possible that this display is judged a current waveform If the aliasing is sus
11. POWER vorge ac a 230V 10 selectable REQUIREMENT L egqvency z or 60Hz Power Consumption Approx 70VA 60W max Dimensions 275 W X 130 H X 370 D mm MECHANICAL SPEC Indoor use Altitude up to 2000 m Ambient temperature ery eee To satisfy specifications 10 C to 35 C 50 F to 95 F Maximum operating ranges 0 C to 40 C 32 F to 104 F Relative humidity 85 RH max non condensing Installation Category H Pollution degree 2 STORAGE TEMPERATUR 10 to 70 C 70 RH maximum E amp HUMIDITY POWEr CORD sis csscaccesmzccencsiix L ACCESSORIES Instruction manual 1 Probe X 1 X 10 2 COn ea Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Se a 3 PRECAUTIONS BEFORE OPERATION 3 1 Unpacking the Oscilloscope The product has been fully inspected and tested before shipping from the factory Upon receiving the instrument please unpack and inspect it to check if there is any damages caused during transportation If any sign of damage is found notify the bearer and or the dealer immediately 3 2 Checking the Line Voltage The oscilloscope can be applied any kind of line voltage shown in the table below Before connecting the power plug to an AC line outlet make sure the voltage selector of the rear panel is set to the correct position correspo
12. frequency units on the upper side of the screen NOTE When the VOLTS DIV or the TIME DIV controls are in uncalibrated setting the AV and AT measurement values will be displayed with divisions When the vertical mode is set to the ADD mode and the CH1 and CH2 VOLTS DIV controls are set to different scales the AV measurement values will be displayed with divisions 6 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL eT 5 8 RS 232 Interface Remote Control 5 8 1 RS 232 Configuration The GRS 6052 6032 contains a DB 9 pin male RS 232 connector for serial communication with a computer or terminal The GRS 6052 6032 RS 232 interface is configured as an RS 232 Data Terminal Equipment so that data is sent from pin 3 and received on pin 2 For remote controls the RS 232 interface has to be connected with a computer or terminal Pin Assignments The pin assignments for RS 232 interface of GRS 6052 6032 are listed below 1 No connection Receive Data RxD input Transmit Data TxD output No connection Signal Ground GND No connection No connection fo Oe a Ga No connection 9 No connection Figure 5 20 Pin assignments of the RS232 connector on the rear panel for DB 9 D Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE
13. measurements are made when the oscilloscope and the unit under test are connected by a common reference ground lead in addition to the signal lead or probe The ground lead of the probe provides the best grounding method for signal interconnection and ensures the maximum amount of signal lead shielding in the probe cable A separate ground lead with a banana plug can also be connected from the unit under test to the oscilloscope ground jack on the front panel Probes A probe provides the most convenient way to connect an input signal to the oscilloscope The standard x1 x10 probes supplied to the oscilloscope are shielded against electromagnetic interference and have a high input impedance for low circuit loading CAUTION To get the best waveform precisely keep probe ground and signal leads as short as possible Misadjust probe compensation can cause measurement error Check and adjust probe compensation whenever a probe is moved to a different channel or oscilloscope As for the probe compensation adjustment procedure refer to the Probe Compensation Coaxial Cables Signal input cable can greatly affect the accuracy of a displayed waveform To maintain original frequency characteristics of the input signal use only high quality low loss coaxial cables Coaxial cables must be terminated at both ends in their characteristic impedance to prevent signal reflections within the cable Use suitable impedance matching devices Art
14. signal 36 HOLD OFF Control knob REAL TIME mode only Used when the signal waveform is complex and stable triggering cannot be attained with the TRIGGER LEVEL 35 knob alone rotate this control knob to adjust hold off time trigger inhibit period beyond sweep duration When control is rotated fully clockwise the hold off period is at MINimum normal The hold off period increases progressively with counterclockwise rotation 37 TRIG EXT This BNC socket is the external trigger signal input Pressing the TRIG SOURCE 31 pushbutton until the information of EXT slope coupling is shown up in the readout switches the input on The outer ground connection is galvanically connected to the instrument ground and consequently to the safety earth contact of the line mains plug The maximum input voltages of the input terminal are shown in the section of 3 6 Withstanding voltage of Input terminals Do not apply valtage higher than the limit Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Storage Control The Storage Control select the digital storage function STORAGE MENU SINGLE UTILITY bb 38 STORAGE REAL TIME mode Switch the REAL TIME mode to digital STORAGE mode by pressing the button In this case all the switches from 39 to 42 are valid When the switch is pressed again in the STORAGE mode the REAL TIME mo
15. 5 10 b shows the undesirable portion of the signal is held off The same waveforms are displayed on the screen without overlapping digital signal cycle Highlighted parts Pa F are displayed Sweep waveform Figure 5 10 a Hold off Time Control Adjusting the HOLD OFF time dj Figure 5 10 b Hold off Time Control a ATS Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL iS Observing the Synchronization of two Waveforms When two signals of the CH1 and CH2 have the same frequencies with an integral number or a specific time difference the SOURCE selects either CH1 or CH2 as a reference signal Select CH1 signal from CH1 position and select CH2 signal from CH2 position as a reference Set the SOURCE to VERT MODE for observing the signal of different frequencies Switch the sync signal alternately to each channel the waveform of each channel will be triggered stably When set the SOURCE to VERT MODE and set the ALT CHOP to ALT the input signals applied to CH and CH2 will become trigger source alternately during sweep Consequently even the waveforms of different frequency of each channel can be triggered stably Apply a sine wave to CH1 and a square wave to CH2 A s shown in Figure 5 11 are at the level possible
16. 56 MAG Interpolation M 3 Parameters 3Bytes Sets or queries the MAG interpolation function Syntax M3 001 M3 Arguments Parameters 000 gt Dot mode 001 Linear mode Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Other Commands Real Time Storage mode il O 1 Parameters 3Bytes Ear Sets or queries the instrument operation mode Syntax 01 001 01 Arguments Parameters 001 Real Time mode 000 gt Storage mode Run Stop O 2 Parameters 3Bytes Sets or queries the waveform Run Stop function Syntax 02 001 02 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Arguments Parameters 000 Stop 001 Run O l Parameters 3Bytes ERCA Sets or queries the text intensity Syntax 03 030 03 Arguments Parameters 000 Disable text display 001 Min to 060 Max Text intensi iumine intensity O 4 A Parameters 3Bytes Lo lele Sets or queries the illumine intensity Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL eee Syntax 04 125 04 00 Arguments Parameters 000 Disable illum
17. 6052 6032 OSCILLOSCOPE USER MANUAL SE RST x R S T Load factory default setting into instrument Vertical Controls Commands Vertical Scale V 1 Parameters 3Bytes Ov a e target Sets or queries the vertical gain of the specific channel Syntax V1 010A V1 B Arguments Parameters 001 20V DIV 002 10V DIV 003 5V DIV 004 2V DIV 005 1V DIV 006 5V DIV 007 2V DIV 008 1V DIV 009 50mV DIV 010 gt 20mV DIV 011 10mV DIV 012 5mV DIV 0132V DIV 014 ImV DIV Target A Channel B Channel 2 74 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Input Coupling v o 2 Ap Parameters 3Bytes Ji Taa V Jal a Target Sets or queries the input coupling states Syntax V2 001B V22A Arguments Parameters 000 Place scope in DC coupling state 001 gt Place scope in AC coupling state 002 Place scope in grounding state Target A gt Channel 1 B Channel 2 Display V 3 i Parameters 3Bytes target lv 3 2 target Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Sets or queries the channel s display Syntax V3 001A V3 B Arguments Parameters 000 Disable channel display 001 Enable channel di
18. ARIABLE EEE EEE EE EE EE A E E EEEE ke REFO Recall REFO memory REFO Recall REF9 memory Turning the VARIABLE control knob clockwise to change the number of reference memory from REFO to REF9 while turning the knob counterclockwise to change the number in the reverse order Recall the waveform on the CRT by pressing the RECALL pushbutton the readout then indicates the associated readout information of I When this pushbutton is pressed again the displayed waveform will be removed Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL SSS MMM 5 7 Measurement Application The oscilloscope has a cursor measurement system for making accurate direct readout voltage time and frequency measurements The measurements described in this section are examples of typical applications using this measurement system After becoming familiar with the controls indicators and capabilities of the instrument you can develop convenient methods to make the special measurement for your own applications Proceed a measurement by using the cursor according to the following steps l Press the AV AT 1 AAT OFF pushbuttons to turn on the cursor and measurement readout 2 Press the pushbutton to select the seven measurement function in the sequence as below AV AT 1 AT OFF 3 Press the C1 C2 TRK pushbutton to select C1 curso
19. Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 46 Z Axis Input BNC socket Connect external signals to the Z axis amplifier for intensity modulating the CRT display This terminal is DC coupled The intensity is lowered by a positive signal while it is increased by a negative signal 47 RS 232 Connector Connect to other equipment with the RS 232 interface Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 5 OPERATION METHOD This section contains basic operation information and techniques that should be considered before proceeding any measurement As for the location and function of instrument controls connectors and indicators refer to the Instruction of Front Panel and Rear Panel of this manual 5 1 Readout Display The CRT readout display indicates how to set up the instrument controls No physical marking shown on the rotating switches indicates the control setting A key to the location and type of readout information display are illustrated in figure 5 1 a and 5 1 b Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL ee MEASUREMENT FUNCTION AND VALUE SAVE OR RECALL MESSAGE NO OF MEM M0 M9 eSA
20. NG AC SLOPE 38 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL ee a 7 Observe the displayed waveform and compare them with the waveforms shown in figure 5 2 If either probe needs to be adjusted proceed the step 8 If either probe does not need to be adjusted proceed the Function Check Over Compensated ct tr tf Under Compensated Correctly Compensated Figure 5 2 Typical Compensation Waveform 8 Adjust the probe by using a small insulated screwdriver Slowly rotate the adjustment control until the probe is properly compensated Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 5 4 Function Check When you start to check the operation of your oscilloscope proceed the following instruction 1 Install the x10 probes onto CH1 and CH2 inputs 2 Connect the probe tips to the CAL test point of the oscilloscope 3 Set the oscilloscope controls to display both channels VERTICAL VOLTS DIV 0 2V COUPLING DC ALT CHOP CHOP HORIZONTAL TIME DIV 0 5ms TRIGGER MODE ATO SOURCE VERT COUPLING AC SLOPE 1 The figure 5 3 below illustrates a satisfactory display The waveform should be approximately 0 5Vp p at a frequency of 1kHz that confirms the vertical and horizontal deflection function of the o
21. RS 6052 6032 OSCILLOSCOPE USER MANUAL Trigger Commands Trigger Made Enn Parameters 3Bytes ala Sets or queries trigger mode a Syntax T1 001 T1 Arguments Parameters 000 gt Auto trigger mode 001 Normal trigger mode 002 Single trigger mode Trigger Source Parameters 3Bytes Sets or queries the trigger source Syntax T2 001 84 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL T2 Arguments Parameters 000 gt VERT 001 Channel 1 002 Channel 2 003 Line 004 gt External Trigger Coupling or ale Parameters 3Bytes Sets or queries the trigger coupling Syntax T3 001 T3 Arguments Parameters 000 AC couple 001 High frequency reject 002 Low frequency reject igge arna Parameters 3Bytes 85 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Sets or queries TV trigger mode Syntax T4 001 T4 Arguments Parameters 000 Disable TV trigger 001 Vertical TV trigger mode 002 Horizontal TV trigger mode Trigger Slope T 5 Parameters 3Bytes s e Sets or queries trigger slope mode Zz Syntax T5 001 T5 Arguments Parameters 000 Negative trigger slope 001 Positive trigger slo
22. SER MANUAL Trigger controls The trigger controls determine the sweep start timing for both signals EXT TRIG MQ 2850F 4 O7 soav cat IT MAX 400Vpk 30 ATO NML Pushbutton and indicator LEDs Pressing the pushbutton to select auto or normal trigger mode The actual setting is indicated by a LED Each time when the pushbutton is pressed the trigger mode changes in the sequence ATO NML ATO ATO Auto Select the automatical mode the sweep free runs will display a baseline trace when there is no trigger signal The setting of triggering level changed only when the TRIGGER LEVEL control is adjusted to a new level setting NML Normal Select the normal mode the input signal will trigger the sweep when the TRIGGER LEVEL control is set within the peak to peak limits of an adequate trigger signal When the sweep is not triggered no baseline trace will be displayed Use this mode when effecting synchronization to a very low frequency signal 25Hz or less Ea ADA lt Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL __ 31 SOURCE Pushbutton Pressing the pushbutton to select the trigger signal source The actual setting is indicated by the readout SOURCE slope coupling Each time when the pushbutto
23. T RST V1 lt Parameters 3bytes gt lt Target 1byte gt V1 lt Target 1byte gt Vertical Scale V2 lt Parameters 3bytes gt lt Target 1byte gt Input Coupling V2 lt Target byte gt V3 lt Parameters 3bytes gt lt Target I byte gt Display V3 lt Target Ibyte gt V4 lt Parameters 3bytes gt lt Target 1 byte gt Probe V4 lt Target 1byte gt V5 lt Parameters 3bytes gt lt Target 1 byte gt V VAR V5 lt Target 1byte gt V6 lt Parameters 3bytes gt Invert V6 V7 lt Parameters 3bytes gt ADD V7 70 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL iz T V8 lt Parameters 3bytes gt ALT CHOP V8 H1 lt Parameters 3bytes gt Horizontal Scale ai H2 lt Parameters 3bytes gt lt Target lbyte gt Pre trigger Position ls 5 H3 lt Parameters 3bytes gt H VAR H3 H4 lt Parameters 3bytes gt XY Mode H4 7 m H5 lt Parameters 3bytes gt wee agnification p Magnifica as H6 lt Parameters 3bytes gt MAG ALT E H6 T1l lt Parameters 3bytes gt Trigger Mode r1 T2 lt Parameters 3bytes gt Trigger Source 729 a T3 lt Parameters 3bytes gt Trigger Couple T3 J T4 lt Parameters 3bytes gt TV Trigger T4 7l Artisan Technology Gro
24. Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL qanae e A yies a 4S SU BE bo OF Orok O24 s e008 00e O i Of ee wy B 7 EE O ie 0 0 KORO a f OFOPOR J I lt gt a Oe Gif OO O OHOIN aoa f gt O0 OIO ofo zi A FE OROL O j S t 7 Front panel of GRS 6052 OR oy uag Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 4 1 Front Panel Display controls The display controls adjust the on screen appearance of the waveform and provide a probe compensation signal source e CURSORS POWER VARIAB Piney Crane Ru 13 SSA O MOO duw RECALL OO TRACE 0 4 Focus O O cL O SVpp iHz E 1 POWER Pushbutton When switch on the oscilloscope to have all LEDs lighted and wait a few seconds the normal operation mode is present Then the last settings become activated and the LED indicates ON condition 2 TRACE ROTATION The TRACE ROTATION is for aligning the horizontal trace in parallel with graticule lines This potentiometer can be adjusted with a small screwdriver Artisan Technology G
25. Time 10ns DIV FUNCTIONS MAG Interpolation Dots Linear ALT MAG Function Available Auto Norm Single Single roll Roll X Y Average 2 256 Run Stop 0 10DIV in 0 02DIV steps at 5 u s DIV 0 1s DIV X axis CH Y axis CH2 Storage Bandwidth DC 50MHz GRS 6052 DC 20MHz GRS 6032 Sweep Time DIGITAL Sweep Magnification Smoothing Function Pre trigger X Y Operation z H 100 points DIV V 25 points DIV X Y 25 X 25 points DIV 10 sets REFO REF9 with back up memory Display Resolution Waveform SAVE RECALL Voltage approx 20mV DIV with 50Q terminal Bandwidth 50Hz to at least SMHz Voltage 0 5V 3 Frequency approx 1kHz square wave OUTPUT i Signal Output SIGNAL Calibrator Output Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL a EE O E ES a a a a e CHI1 CH2 sensitivity sweep time trigger Panel Setting Display condition digital storage function Panel Setting Save amp Recall 10 sets CURSOR ee READOUT amp eee a E AV AT VAT CONTROL C M ursor Resolution i INTERFACE uror Measurement Effective Cursor Range Vertical 3 DIV Horizontal 4 DIV Text Readout Intensity Adjustable RS232 Interface Remote control via a PC 109 z LINE
26. UTION Caution statements identify conditions or practices that could result in damage to this product or other property The following symbols may appear in this manual or on the product A A 7 DANGER ATTENTION Protective Earth ground High Voltage refer to Manual Conductor Terminal Terminal Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL FOR UNITED KINGDOM ONLY NOTE This lead appliance must only be wired by competent persons WARNING THIS APPLIANCE MUST BE EARTHED IMPORTANT The wires in this lead are coloured in accordance with the following code Green Yellow Earth Blue Neutral Brown Live Phase As the colours of the wires in main leads may not correspond with the colours marking identified in your plug appliance proceed as follows The wire which is coloured Green amp Yellow must be connected to the Earth terminal marked with the letter E or by the earth symbol or coloured Green or Green amp Yellow The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Blue or Black The wire which is coloured Brown must be connected to the terminal marked with the letter L or P or coloured Brown or Red If in doubt consult the instructions provided with the equipment or contact the supplier ii Artisan Technology Group Quality I
27. VE m gt RECALL TEXT INTEN OR ILLUM ALT or CHOP CH1 PROBE x10 CH1 VAR UNCAL gt CH1 VOLTS DIV CH1 INPUT COUPLING AG A DC GND 7 CH2 VAR UNCAL gt CH2 PROBE X10 CH2 INV ADD CH2 VOLTS DIV CH2 al INPUT GOUPLING AC A DC GND 7 SWEEP VAR UNCAL gt SWEEP TIME S DIV TRIG SOURCE VERT CH1 CH2 LINE EXT Figure 5 1 a REAL TIME mode Readout Layout TRIG COUPLING AC HFR LFR TRIG SLOPE F Lt or TV POL ar Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL SAMPLING MODE EQU 0 2us 2us div SMPL 5us 0 18 div ROLL 0 28 100s div PRE TRIGGER OR TRIGGER POINT CURSOR MEASUREMENT SAMPLING NO OF AVERAGE FUNCTION AND VALUE RATE OR SINGLE MODE 20MS s REFERENCE MEMORY REFO REF9 REFERENCE MEMORY VOLTS DIV REFERENCE MEMORY TIME DIV Figure 5 1 b Storage Mode Readout Layout Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Coona uaa a a a 5 2 Connecting Input Signals Grounding The most reliable signal
28. XT 8 CURSORS MEASUREMENT FUNCTION There are two pushbutton and associated the VARIABLE 9 contro knob When the pushbutton is pressed the three measurement functions will be selected in the sequence as follows AV AT l AT OFF AV Two horizontal cursors appear The voltage between the two cursors ees AD eee Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL _ _ _ _ _ is calculated according to the setting of VOLTS DIV and displayed with AV on the upper side of the CRT Single channel mode CH1 or CH2 The AV measuring result is automatically related to the deflection coefficient of the active channel The readout displays A V1 or INN D2 Dual channel mode The cursor lines must be set on the CH1 or CH2 signal As the deflection coefficients may be different it will be required to select between the deflection coefficient of CH1 and CH2 ADD mode In ADD addition mode normally two input signals are displayed as one signal sum or difference As the result can only be determined if both calibrated deflection coefficients are equal the readout indicates A V without any additional channel information Different deflection coefficient settings or uncalibrated deflection coefficien
29. an Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL ALT CHOP i V in Parameters 3Bytes v lele Sets or queries the ALT CHOP mode Syntax V8 001 V8 Arguments Parameters 000 ALT mode 001 CHOP mode Horizontal Controls Commands Horizontal Scale H dh Parameters 3Bytes a ite Sets or queries the horizontal time base scale Syntax H1 010 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL H1 Arguments Parameters 001 100s DIV 002 gt 50s DIV 003 20s DIV 004 10s DIV 005 gt 5s DIV 006 gt 2s DIV 007 1s DIV 008 5s DIV 009 2s DIV 010 1s DIV 013 10ms DIV 016 Ims DIV 019 1Ims DIV 022 10us DIV 025 lus DIV Pre trigger Position 011 50ms DIV 014 5ms DIV 017 5ms DIV 020 50us DIV 023 5us DIV 026 5us DIV a del Parameters 3Bytes 012 20ms DIV 015 2ms DIV 018 2ms DIV 02120us DIV 024 2us DIV 027 2us DIV Target H 2 Target Sets or queries the horizontal pre trigger position Syntax H2 300A H2 100B H2 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL E Arguments Parameters If Target A
30. ate 45 out of phase To use the oscilloscope in the X Y mode proceed the following steps 1 Connect the horizontal or X axis signal to the CHI input 2 Connect the vertical or Y axis signal to the CH2 input 3 Set the X Y button to X Y operation shown as Fig 5 7 below Use the HORIZONTAL POSITION contro to adjust the X axis Note When high frequency signals are displayed in the X Y operation note the frequency bandwidths and phase difference between X and Y axis Refer to 2 SPECIFICATION section for details Figure 5 7 Typical single X Y display Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL _ _ _ K Magnifying Waveform Events Use the MAG pushbutton to view small portions of a waveform as which is too far back from the starting point to view by using the TIME DIV control To use the MAG button proceed the following steps 1 Adjust the TIME DIV to the fastest sweep that displays the event 2 Rotate the HORIZONTAL POSITION control to move the event to display on the center of screen 3 Press the MAG button 4 Select MAG X5 MAG X10 or MAG X20 for MAG function When above procedures have been done the displayed waveform will be expanded 10 times to the right and left from the center of screen as center of
31. ated linearly and the waveform is displayed smoother than at DOT This is effective for a square wave or sine wave 4 Save reference memory setting mode When the MENU 4 SAVE is displayed at the top right of the CRT the save reference memory can be selected Save completed tt IME NU aS ALY E ease IRIEL EO Mf ie Source Waveform CHI only CH1 CH2 only CH2 REFO Save to REFO memory ADD only CH1 CH2 SUB only CHI CH2 REFO Save to REF9 memory Setting marker by VARIABLE The source waveform is automatically switched by vertical mode When both CH1 and CH2 are active pressing the VARIABLE control knob to select the source waveform between CH1 and CH2 Turning The VARIABLE control knob clockwise to change the number of reference memory from REFO to REF9 and turning the knob counterclockwise to change the number in the reverse order When the source waveform and the number of reference memory are established pressing the SAVE pushbutton to write the source oe y oa Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL waveform in the memory and indicate the associated readout information of l 5 RECALL reference When the MENU5 RECALL is displayed at the top right of the CRT the recall reference memory can be selected Recall Completed RIES FLO Mg gt vise mi Setting marker by V
32. aticule lines eliminate parallax viewing error between the trace and the graticule line 2 Multiple Digital Storage Functions Digitizing repetitive waveform up to full bandwidth 50 30MHz through the use of equivalent sampling S00MS s 2k word acquisition memory per channel up to 10 sets SAVE RECALL reference memories with back up are provided Pre trigger function for observing waveforms before triggering The trigger point can be selected from 0 10 DIV in 0 02DIV steps Roll mode is ideal for observing flickering low speed signals The TIME DIV range up to 100s The averaging function can be selected freely from 2 to 256 This effectively reduces noise from repetitive signals The smoothing dot join function provides linear connections between the captured point ensuring that digitized signals are displayed without gaps In the magnification mode the DOT or LINEAR interpolation can be selected according to the waveform The built in RS 232C interface enables remote control operation and signal processing via a PC Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL The X Y mode is same as the real time mode The X horizontal signal is connected to the input of CH1 the Y vertical signal is applied to the input of CH2 and the storage waveform bandwidth up to 5S0MHz 30MHz 3 ALT MAG Function both Real Ti
33. de is established again In the STORAGE mode the RUN LED blinks in synchronism with sampling 39 MENU Press the pushbutton to change the ON OFF of smoothing the number of average the interpolation method and the selection of SAVE RECALL waveform memory Each pressing changes the setting mode and the present setting mode is displayed at the top right on the CRT The settings in each mode are changed by the VARIABLE 9 control knob Please refer to section 5 7 for details 40 RUN STOP Pushbutton and indicator LED Pressing this pushbutton to stop sampling resulting in the hold state and the RUN LED is off The current setting is indicated by the readout STOP Further pressing the pushbutton to release hold state and start sampling states Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 41 SINGLE Pressing the pushbutton to set the SINGLE mode and the SINGLE message will be indicated in the readout In this operation mode a single signal acquisition process or sweep can be started with a trigger Providing the trigger circuit has been previously activated with reset function SINGLE is automatically switched to normal triggering NML LED lights up Otherwise the trigger automatic would start the signal acquisition processes without a
34. e instrument input terminals and probe Input terminals are shown in the following table Do not apply voltages higher than these limits p Input terminal Maximum input voltage CH1 CH2 inputs 400V DC AC peak EXT TRIG input 400V DC AC peak Probe inputs 600V DC AC peak Z AXIS input 30V DC AC peak CAUTION To avoid damaging the instrument do not apply input voltages of the frequency over 1 kHz to the instrument Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL eee a 4 PANEL INTRODUCTION After the instrument is switched on all the important settings are displayed in the readout The LED s located on the front panel assist operation and indicate additional information Incorrect operation and the electrical end positions of control knobs are indicated by a warning beep All of the pushbuttons VOLTS DIV control knobs TIME DIV control knobs are electronically selected and their functions and settings can therefore be stored and remotely controlled as well Some controls are only operated in the digital storage mode or have a different function Explanation pertaining to them are indicated with the hint of storage mode only The front pane is subDIVided into five sections Display controls Vertical controls Horizontal controls Trigger controls Digital storage functions Artisan
35. e to change he number from OFF to 2 4 8 16 32 64 128 256 and turning the knob counter clockwise to change the number in the reverse order The average waveform is displayed after the data of the set sweep number has been acquired When the number of average is 16 the data is acquired 16 times the RUN LED blinks 16 times Then the data is averaged and the average waveform display is updated Thus the non repetitive signal affected by asynchronous noise can be picked up The average operation is performed by setting the number of average In the ROLL mode the average operation is not performed 3 Interpolation Method Selection mode When the MENU 3 INTRPL is displayed at the top right of the CRT THE interpolation Method can be selected DOT No interpolation Setting marker by VARIABLE LINEAR Linear interpolation 56 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL _ ___ The mode selection is made by the VARIABLE control knob The interpolation method is how to interpolate the magnified data while magnifying the display waveform in the horizontal direction except for the SAVE RECALL reference waveform In the case of DOT the waveform is magnified as is in the horizontal direction In the case of LINEAR the data is interpol
36. ertical VAR function enable Vertical scale 1 14 20V DIV ImV DIV Horizontal scale 10 27 1s DIV 2us DIV Combining Commands You can use a semicolon to combine commands and queries The GRS 60X2 executes coherent commands in the order it receives them When you coherent queries the GRS 60X2 combine the responses into a single response message For example if the channel 1 display is ON 001 and horizontal time base scale equals to Ims DIV 016 the query commands must add 1 byte message terminator V3 727A H1 Instrument will return the message 00101 6 68 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL t a ST Buffer Size The command receive buffer of instrument is 128 bytes The return message buffer of instrument is 1024 bytes If your combining commands size is larger than 128 bytes commands will be lost If you query the waveform data WA or WB the instrument will return 1000 bytes waveform data Do not use any query commands during the data transmission Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Command List Note Every command must add 1 byte message terminator of LF 0x0A Function Transmission Format IDN IDN CLR CLR ULK ULK RS
37. expansion Figure 5 8 Magnified Waveform AR Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL ee M a MAG ALT Function The input Signal is displayed by pressing MAG magnify and MAG ALT LED light buttons 1 Set the wished portion of the waveform to the center of the screen for magnification 2 The magnified waveform spreads about 3 DIVisions below the normal x 1 waveform 3 It is a normal function when the MAG ALT button is pressed the characters will be vanished from the screen Figure 5 9 a Mag X 1 Waveform Figure 5 9 b Mag X 10 Waveform Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL EEE Operating Hold off time Control REAL TIME mode only When the measured signal is a complex waveform with two or more repetition frequencies period triggering with the LEVEL control alone may not be sufficient to attain a stable waveform display In such a case the sweep can be stable synchronized to the measured signal waveform by adjusting the Hold off time of the sweep waveform Figure 5 10 a shows several different waveforms which overlapped on the screen marking the signal observation unsuccessful when the hold off is set to minimum Figure
38. for synchronization Input coupling DC Input coupling AC on n ar N ee i fete CHI p oo a i 4 i 0V Br pane ff ov fo ne fo T ORLA Ley NA aet hn mmes aa a fa do Pee arepo n ce ers i i aes I A t E z amp f li i cH2 DESE pe wardunX an ons ov f os ow f La Om lomvf an ERTL AC tom lOmin tm EN Figure 5 11 Trig Source on VERT Apply AC coupling to CH2 in order to expand the synchronization range If the input signal of CH or CH2 becomes small adjust VOLT DIV control knob to obtain sufficient amplitude The VERT MODE triggering required 2 0 DIV which is larger than the amplitude of CH1 or CH2 48 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL SSS The VERT MODE triggering is not possible when the signal is applied only to one channel as shown in Figure 5 12 below Figure 5 12 Trig Source on VERT one channel ALTERNATE TRIGGER The Jittering wave as shown in Figure may appear on the screen when a gently slopping signal is displayed 10 cycles or less approximately by setting VERT MODE to SOURCE and setting ALT CHOP pushbutton to ALT For detailed and clear observation of each signal set VERTICAL mode to CH1 or CH2
39. from channel I and channel 2 and vice versa CHOP Indicates chopper The channel switching occurs constantly between channel and channel 2 during each sweep In the STORAGE mode ALT or CHOP mode is automatically selected by TIME DIV range The ALT mode is established for the sweep range of 0 5ms DIV or faster The CHOP mode is established for the sweep range of Ims DIV or slower 16 ADD INV Pushbutton with double functions ADD Displays the symbol in the readout indicates additional mode Whether the algebraic sum addition or the difference subtraction of both input signals is displayed depends on the phase relationship and the INV setting As a result both signals are displayed as one signal For correct measurements the deflection coefficients for both channels must be equal INV Pressing and holding the pushbutton to set the channel 2 invert function on or off The invert on condition is indicated by the Wy 7 symbol in the readout The invert function causes the signal display of channel 2 to be inverted by 180 17 CH1 VOLTS DIV 18 CH2 VOLTS DIV Control knob for channel 1 channe 2 has double functions Turning the knob clockwise to increase the sensitivity in 1 2 5 sequence ioe Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL eS SE ee eee and turning it in the opposite direction CCW to dec
40. gh Frequency Reject Attenuates high frequency triggering signal components above 50kHz HFR coupling is useful for providing a stable display of low frequency components of complex waveforms and eliminates high frequency interference from the trigger signal LFR Low Frequency Reject Attenuates low frequency triggering signal components below 30kHz and blocks the DC component of the trigger signal LFR coupling is useful for producing stable triggering on the high frequency components of complex waveforms and rejecting low frequency interference or power supply hum from the trigger signal 35 TRIGGER LEVEL Control knob with TRG LED Turning the control knob causes a different trigger input setting voltage and set to a suitable position for the starting of triggered sweep of the waveform When rotate clockwise the control knob the trigger point moves toward the positive peak of the trigger signal and rotate it eee eee Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL C counterclockwise to move the trigger point toward the negative peak of the trigger signal When the setting voltage value is out of the changing portion of the observation waveform the synchronization sweep stops TRG LED The TRG LED is lit if the triggering conditions are met Whether the LED flashes or is lit constantly depends on the frequency of the trigger
41. he knob clockwise to reduce the deflection coefficient in a 1 2 5 sequence and turning it in the opposite direction CCW to increase The time coefficient s will be displayed in the readout In the REAL TIME mode the time deflection coefficients between 0 5s DIV and 0 2 s DIV can be chosen in 1 2 5 sequence if the MAG function is not activated In the STORAGE mode the sampling method is changed automatically by the TIME DIV range Equivalent sampling EQU 0 2 u s DIV to 2 ws DIV Only a repetitive signal can be stored Normal sampling SMPL 5 u s DIV to 0 1s DIV Single slot and repetitive signal can be stored Roll mode 0 2s DIV to 100s DIV For observing flickering low speed signals VAR Real Time mode only Pressing the pushbutton to select the TIME DIV control knob function between time base switch and vernier variable In the Real Time mode after switching on the VAR the time deflection coefficient is still calibrated until further adjustments are made Turn the TIME DIV control knob counter clockwise to increase the time deflection coefficient reduce the deflection speed and the deflection coefficient becomes uncalibrated The current setting is displayed by the gt symbol in the readout Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL D 27 X Y Pressing the pushbutton when using the instrument as an X Y oscillosc
42. he save and recall memory can be selected by the MENU pushbutton Each time when the MENU pushbutton is pressed the readout displays at the top right of the CRT in the sequence as follows MENU 1 SMOOTH MENU 2 AVERAGE MENU 3 INTRPL MENU 4 SAVE MENU 5 RECALL OFF 1 Smoothing selection mode When the MENU 1 SMOOTH is displayed at the top right of the CRT the smoothing i is made on and off OFF No Smoothing Setting marker by VARIABLE N Smoothing In case of OFF the storage waveform is displayed by dots while changing to ON the dots are connected smoothly as result of a smooth waveform display When the sampling frequency is low with respect to the input signal frequency when the signal of more than 5 cycles per division is connected the amplitude to be display may be small In this case set the smoothing mode to OFF to display the waveform of the similar amplitude with the input signal The setting can be done by the VARIABLE contro knob Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 2 Average setting mode When the MENU 2 AVERAGE is displayed at the top right of the CRT the number of average can be set OFF Average is not performed Setting marker by VARIABLE 256 Average is performed 2 256 times The number of average is selected by the VARIABLE contro knob Turning the knob clockwis
43. his manual contains proprietary information which is protected by copyrights All rights are reserved No part of this manual may be photocopied reproduced or translated to another language without prior written consent of Good Will company The information in this manual was correct at the time of printing However Good Will continues to improve products and reserves the rights to change specification equipment and maintenance procedures at any time without notice Good Will Instrument Co Ltd No 95 11 Pao Chung Road Hsin Tien City Taipei Hsien Taiwan Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com Declaration of Conformity We GOOD WILL INSTRUMENT CO LTD No 95 11 Pao Chung Rd Hsin Tien City Taipei Hsien Taiwan declares that the below mentioned product GRS 6052 GRS 6032 are herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Law of Member States relating to Electromagnetic Compatibility 89 366 EEC 92 31 EEC 93 68 EEC and Low Voltage Equipment Directive 73 23 EEC For the evaluation regarding the Electromagnetic Compatibility and Low Voltage Equipment Directive the following standards were applied EMC Electrostatic Discharge EN 55011 1998 Group I class B EN 61000 4 2 1995 C
44. illoscope by pressing a button Now you have the power for digital capture and analysis of elusive single shots with a full 20MS s sample rate The instruments provide with a high speed A D converter for each channel to enable the measurement memory and analysis of high speed phenomena A microprocessor based operating system controls most of the functions of the instrument including cursor readout and digitized panel setting On screen alphanumeric readout and cursor function for voltage time and frequency measurement provide extraordinary operational convenience Ten different user defined instrument settings can be saved and recalled without restriction The vertical deflection system has two input channels Each channel has 14 basic deflection factors from ImV to 20V per DIVision The horizontal deflection system provides sweep time from 100s to 0 2 u s per DIVision The trigger system provides stable triggering over the full bandwidth of the vertical deflection system Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL S eT 1 2 Features Additionally the oscilloscope offers several other features 1 High intensity and internal graticule CRT The oscilloscope employs a high intensity 6 inch retangular type cathode ray tube with red internal graticule It displays clear readable traces even at high sweep speeds Internal gr
45. ine display 001 Min to 240 Max Illumine intensity 92 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL EEE 6 MAINTENENCE The instructions below are executed by qualified personnel only To avoid electrical shock do not perform any servicing other than the operating instructions unless you are qualified to do so 6 1 Fuse Replacement If the fuse blows the power lamp indicators will not light and the oscilloscope will not start The fuse should not normally open unless a problem has developed in the unit Try to determine and correct the cause of the blown fuse and replace only with a fuse of the correct rating and type on the rear panel WARNING For continued fire protection Replace fuse only with 250V fuse of the specified type and rating and disconnect power cord before replacing fuse 6 2 Line Voltage Conversion The primary winding of the power transformer is tapped to permit operation from 100 120 or 230VAC 50 60Hz line voltage Conversion from one line voltage to another is done by changing the line voltage selector switch as shown in page 7 The rear panel identifies the line voltage to which the unit was factory set To convert to a different line voltage perform the following procedure 1 Make sure the power cord is unplugged 2 Adjust the line voltage selector switch to the desired line voltage position
46. isan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 5 3 Adjustments and checks Trace Rotation Adjustment Normally when the trace is in parallel with the center horizontal graticule line there will be no need to adjust the TRACE ROTATION If necessary adjust the TRACE ROTATION to make the baseline trace parallel to the center horizontal graticule line by using a small straight blade screwdriver or alignment tool Probe Compensation To minimize the distortion of measured waveforms check the compensation of your probes before using them The probe compensation should be checked periodically whenever the probes are moved to different input channels l 1 Install the probes onto the oscilloscope Press the BNC connector onto the channel input and rotate the connector to lock it into place 2 Set the probe slide switches to the x10 position 3 Briefly pressing the CH1 CH2 button to set the oscilloscope to channel 1 and channel 2 4 Pressing and holding the Px10 button to set the indicated deflection coefficient of the channel displayed in the readout as a symbol P10 5 Attach the probe tips to the CAL connection in the front of the oscilloscope 6 Set the oscilloscope controls to display both channels VERTICAL VOLTS DIV 0 2V COUPLING DC ALT CHOP CHOP HORIZONTAL TIME DIV 0 5ms TRIGGER MODE ATO SOURCE VERT COUPLI
47. lding the RECALL pushbutton for approx 3 seconds the readout then indicates the associated readout information of gt Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Vertical controls The vertical controls select the displayed signals and control the amplitude characteristics 11 CH1 Pushbutton 12 CH2 Pushbutton Pressing briefly the CH CH2 button to set the channel 1 channel 2 of the instrument on the deflection coefficient will be displayed in the readout indicating the current conditions 13 CH1 POSITION Control knob The vertical trace position of channel 1 can be set with the control knob When X Y operation in the Storage mode CH1 POSITION control knob is used for the X deflection 14 CH2 POSITION Control knob The vertical trace position of channel 2 can be set with the control knob In X Y operation CH2 POSITION control knob is used for the Y deflection Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL eee M MM 15 ALT CHOP In the REAL TIME mode the pushbutton has two functions which are required and available only when both channels are active ALT Displays in the readout indicates alternate channel switching After each time base sweeps the instrument internally switches over
48. mat is N 8 1 no parity bit 8 data bits 1 stop bits Computer s Connection A personal computer with a COM port is the essential facility in order to operate the instruction via RS232 interface The connections between GRS 6052 6032 and computer are as follows 1 Connect one end of a RS232 cable to the computer 2 Connect the other end of the cable to the RS232 port on the GRS 6052 6032 3 Turn on the GRS 6052 6032 4 Turn on the computer Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL SS The RS232 connection testing If you want to test whether the RS232 connection is working or not you can send a command from computer For instance using a terminal program send the query command uppercase TDN should return the Manufacturer model number serial number and firmware version in the following format GW GRS 60X2 0 V 1 10 If you do not receive a proper response from the GRS 60X2 please check if the power is on the RS232 configurations are the same on both sides and all cable connections are active Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 5 8 2 RS 232 Remote Control Command Syntax All commands syntax is ASCII format If you want to transfer any of the instructions to an instrument there a
49. me Mode and Storage Mode The primary sweep waveform along with the magnified sweep waveform can be displayed simultaneously using the ALT MAG function The magnification ratio can be selected from among three stages of x5 X10 X20 for magnifying the displayed waveform in the center of the CRT 4 Convenient VERT MODE Triggering The sync signal source is decided automatically when vertical axis mode is switched This means that you need not change the trigger source every time you switch the VERT MODE 5 TV triggering Exclusive TV sync separator circuit technology provides stable TV signal measurements on fields frames and lines 6 Hold Off Real Time Mode only The function allows the obtaining of stable synchronization for even complex waveforms that are difficult to synchronized by adjusting the trigger level alone 7 CH1 Signal Output The CHI signal output ts obtained by branching the input signal in the middle of the signal line As the connector outputs the input signal at a rate of 50mV DIV connecting a frequency counter makes it possible to measure the frequency of a very low signal while observing its waveform Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 8 Z axis intensity modulation Real Time Mode only For applying a blanking signal from an external source The trace displayed on the screen may be intensit
50. n Guaranteed 888 88 SOURCE www artisantg com A rtisan Artisan Technology Group is your source for quality TecmoogyGroup new and certified used pre owned equipment FAST SHIPPING AND SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT DELIVERY Experienced engineers and technicians on staff Sell your excess underutilized and idle used equipment TENS OF THOUSANDS OF at our full service in house repair center We also offer credit for buy backs and trade ins IN STOCK ITEMS www artisantg com WeBuyEquipment 7 EQUIPMENT DEMOS HUNDREDS OF InstraV ea REMOTE INSPECTION LOOKING FOR MORE INFORMATION MANUFACTURERS Remotely inspect equipment before purchasing with Visit us on the web at www artisantg com 7 for more our interactive website at www instraview com information on price quotations drivers technical LEASING MONTHLY specifications manuals and documentation RENTALS ITAR CERTIFIED D a gaa tia Contact us 888 88 SOURCE sales artisantg com www artisantg com
51. n input trigger signal Pressing the RUN STOP pushbutton reset function again to resume a new single event capture which then overwrites the previously recorded display 42 UTILITY The instrument software contains several utility setting Each time when the UTILITY pushbutton is pressed the readout displays the following message in the sequence at the top right of the CRT RS232 baud rate BEEP ON OFF FACTORY DEFAULT loading RS232 Baud Rate The setting of baud rate and data format on the instrument must be the same as the one on the computer The baud rate of the RS 232 interface can be selected by turning the VARIABLE control knob according to the list as follows 300 900 1200 2400 4800 9600 Press the VARIABLE control knob to set RS 232 baud rate the screen will display RM in the upper left corner to show GRS 6052 6032 in the Remote Control mode Note When the baud rate is set the front panel control will be locked Press UTILITY can unlock the front panel control and disable remote control Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL C BEEP ON OFF When the BEEP is displayed turning the VARIABLE control knob to set the beep on or off In the OFF condition the acoustic signals actuated by the control limits are switched off FACTORY DEFAULT loading When the FACTORY DEFAULT is displayed
52. n is pressed the trigger source change in the sequence VERT CH CH2 LINE EXT VERT VERT Vertical Mode For observing two waveforms the syne signal changes alternately corresponding to the signals on CH1 and CH2 to trigger the signal CHI The signal applied to the channel input connector is the source of the trigger signal CH2 The signal applied to the channel 2 input connector is the source of the trigger signal LINE The triggering signal is obtained from a sample of the AC power source waveform The trigger source is useful when the displayed waveform frequency is time related to the AC power source frequency EXT The external signal applied through the EXT input connector is used for the external triggering source signal Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 32 TV Pushbutton for video sync signal selection Separate the video sync signal from the composite waveform and direct it to the triggering circuit The horizontal or vertical sync signals are selected by TV pushbutton The current setting is displayed in the readout under item source video polarity TVV or TVH Each time when the pushbutton is pressed the video sync signal is displayed in the sequences as follows TV V T V H OFF TV V TV V Start the main trace at the beginning of a video signal field The polari
53. nding to the line voltage It might be damaged the instrument if connected to the wrong AC line voltage WARNING To avoid electrical shock the power cord protective grounding conductor must be connected to ground When line voltages are changed replace the required fuses shown as below Fuse 100V 90 110V T 1A 250V 120V 108 132V 230V 207 250V T 0 4A 250V WARNING To avoid personal injury disconnect the power cord before removing the fuse holder Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL _ SS __S S SS _ 3 3 Environment The normal ambient temperature range of this instrument is from 0 to 40 C 32 to 104 F To operate the instrument over this specific temperature range may cause damage to the circuits Do not use the instrument in a place where strong magnetic or electric field exists as it may disturb the measurement 3 4 Equipment Installation and Operation Ensure there is proper ventilation for the vents in the oscilloscope case If the equipment is used not according to the specification the protection provided by the equipment may be impaired 3 5 CRT Intensity To prevent permanent damage to the CRT phosphor do not make the CRT trace brighten excessively or leave the spot stay for an unreasonably long time 3 6 Withstanding Voltages of Input Terminals The withstanding voltages of th
54. nstrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL TE This cable appliance should be protected by a suitably rated and approved HBC mains fuse refer to the rating information on the equipment and or user instructions for details As a guide cable of 0 75mm should be protected by a 3A or 5A fuse Larger conductors would normally require 13A types depending on the connection method used Any moulded mains connector that requires removal replacement must be destroyed by removal of any fuse amp fuse carrier and disposed of immediately as a plug with bared wires is hazardous if a engaged in live socket Any re wiring must be carried out in accordance with the information detailed on this label Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL kooo IH MH Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL a 1 PRODUCT INTRODUCTION 1 1 Description The GRS 6052 and GRS 6032 set a standard in performance and economy each equips with two professional scopes in one They can be operated as a real time 50 or 30MHz analog oscilloscope and become a full function digital storage osc
55. nstrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL The symbol must not be activated unless a 10 1 attenuator probes are used 23 CH1 X Input BNC socket This BNC socket is the signal input for channel 1 In X Y mode signals at this input are used for the X deflection The outer ground connection is galvanically connected to the instrument ground and consequently to the safety earth contact of the line mains plug 24 CH2 Y Input BNC socket This BNC socket is the signal input for channel 2 In X Y mode signals at this input are used for the Y deflection The outer ground connection is galvanically connected to the instrument ground and consequently to the safety earth contact of the line mains plug Horizontal controls The horizontal controls select the time base operation mode and adjust the horizontal scale position and magnification of the signal HORIZONTAL wm MAG lt q POSITION gt ya S Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL E 25 H POSITION Real Time mode only The control knob enables a horizontal position shift of the signals In combination with MAG the function makes it possible to shift any part of the signal on the screen In X Y mode the control knob are used for the X deflection 26 TIME DIV Y AR Control knobs Turning t
56. of commands are sent to the instrument it must add a LF to be a judgment for message terminator As for query command the return message of the instrument is also added a LF for PC to judge message terminator A semicolon separates one command from another when the commands appear on the same line Return Data Format If instrument received question mark at the third byte command type of the command it will answers 3 bytes value in ASCII format and 1 byte message terminator of LF 0x0A The following example ask the Time base scale and instrument will return 010 1s DIV Example H 1 ASCII Return 0 1 0 3 bytes ASCII format If instrument receives WA WD It will return 1000 bytes channel 1 channel 2 or 2 recalled waveforms data in Binary format and 1 byte message terminator Example W A ASCII Return 1000 bytes waveform data jaleosucas terminator 0x01 0x05 ae 0x09 Ox0A Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL If instrument receives WO0 W9 It will return 3 bytes waveform information 1000 bytes waveforms data in Binary format and 1 byte message terminator Example W 5 ASCII Return VAR Vertical Horizontal 1000 byte waveform Message scale scale data terminator 0x01 0x05 0x10 0x01 0x05 0x09 Ox0A VAR 0 Vertical VAR function disable VAR 1 V
57. ope The time deflection coefficient is replaced by the X Y symbol in the readout In this mode the X horizontal signal is connected to the input of CH1 the Y vertical signal is applied to the input of CH2 and has a deflection range from less than ImV to 20V DIV at a reduced band width of 500kHz Real Time mode In the Storage mode the X Y operation is same as the REAL TIME mode The storage waveform bandwidth of both X and Y signal are up to 50MHz 30MHz 28 X1 MAG Pressing the pushbutton the select the sweep time between X 1 normal and MAG magnify If the MAG function the signal display will be expanded and consequently only a part of the signal curve is visible The interesting part of the signal can be made visible with the aid of the H POSITION control in the REAL TIME mode 29 MAG FUNCTION xX 5 10 20 MAG When MAG has been done the displayed waveform will be expanded to the right and left with the center of the CRT The magnification ratio can be selected from among three stage of 5 X 10 X20 MAG by pressing this pushbutton ALT MAG Pressing the pushbutton the primary sweep waveform along with the magnified sweep waveform The magnified can be displayed simultaneously using the ALT MAG function The magnified sweep waveform appears 3 DiVisions below the primary sweep waveform Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE U
58. panel indicate value mV 2mV DI Bandwidth 3dB Rise Time 5mV 20V DIV DC 30MHz Approx 1 7ns ImV 2mV DIV DC 7MHz Approx 50ns Maximum Input Voltage 400V DC AC peak at 1kHz or less Input Coupling Input Impedance Vertical Modes CHOP Frequency Dynamic Range REAL TIME mode only Sensitivity Accuracy Vernier Vertical Sensitivity Bandwidth 3dB and VERTICAL Rise Time SYSTEM Approx 1M 2 approx 25pF CH1 CH2 DUAL CHOP ALT ADD CH2 INV Approx 250kHz GRS 6052 8DIV at 40MHz 6DIV at SOMHZ GRS 6032 8DIV at 20MHz 6DIV at 30MHz Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL SS SS EE 0 2 ws DIV 0 5s DIV 20 steps selectable in 1 2 5 Sweep Time sequence continuous variable control between steps HORIZONTAL at least 1 2 5 SYSTEM Accuracy 3 5 at x5 and x10 MAG 8 at x20 MAG Sweep Magnification x5 x10 x20 MAG A F GRS 6052 20ns DIV 10ns DIV uncalibrated Maximum Sweep Time at MAG GRS 6032 50ns DIV 1 Ons DIV 40ns DIV uncalibrated REAL TIME mode ALT MAG Function Available Trigger Modes TAUTO NORM TV Trigger Source VERT MODE CH1 CH2 LINE EXT Trigger Coupling AC HFR LFR TV V TV H Trigger Slope or
59. pe 86 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Waveform Data Commands Dump channel waveform data o Dump channel 2 waveform data Dump 2 recalled waveform data W 0 9 Dump REF 0 9 waveform data Syntax WA W5 Note GRS 60x2 can t return waveform data in real time mode or in roll mode 100s DIV to 2s DIV of storage mode 87 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Menu Commands Smooth 1 Parameters 3Bytes Sets or queries the waveform smooth function Syntax M1 001 M1 Arguments Parameters 000 Disable Smooth function 001 Enable Smooth function Average M 2 Sets or queries the waveform average function Parameters 3Bytes Syntax M2 006 M2 gg Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Arguments Parameters 000 gt Disable average function 001 gt Average number is 2 002 Average number is 4 003 Average number is 8 004 Average number is 16 005 Average number is 32 006 gt Average number is 64 007 gt Average number is 128 008 Average number is 2
60. pected select the REAL TIME mode and check if the display is the same as that in the actual operation mode Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL PRE TRIGGER Measure the waveform before the trigger point Although a conventional oscilloscope displays the trigger point only at the left end of the screen since the sweep starts at the trigger point of the signal the instrument can display the trigger point anywhere on the screen in 0 1DIV steps using the PRE TRIGGER function in the STORAGE mode so that it is possible to measure the waveform before the trigger point precisely 1 When the MENU and CURSOR functions are off the position of the trigger point is displayed 2 The position of the trigger point is set by the VARIABLE contro knob 3 For example in the case of 4 0DIV setting the signal before the rising edge of the waveform the triggered point can be observed as shown in Figure 5 18 below Befor trigger AfterTrigger point Trigger int 4div display point Figure 5 18 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL eae MENU The on off settings of the waveform smoothing the number of average the interpolation method in the horizontal magnification mode t
61. pressing the VARIABLE control knob to overwrite all panel setting memories MEM0O MEM9 please refer to the setting as follows REAL TIME mode gt ON VERTICAL CH1 ON CH2 ON VOLTS DIV 0 5V COUPLING AC HORIZONTAL TIME DIV 100 ws TRIGGER MODE ATO SOURCE CH1 COUPLING AC SLOPE J Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 4 2 Rear Panel The rear panel provides input power and additional signal connections A coment ee LS pi 8 OG Ja AX WARNING T WOR Buc BERTIE MONA cra PRTG eC CODA MT i EOE To aaan TOn CNP FE OREN REA Oy we SEND Teme em na COVRCREIT OUR 02 HOT ABENE Coven NTE El 19 AALTER PERCE SS oo 43 Line voltage selector and input fuse holder Select power source and contain the primary power fuse The fuse rating is shown in the section of 3 2 Checking the line voltage 44 AC power input connector Connect the AC power cord to the power supply of instrument the power cord protective ground connection is connected to the exposed metal part of the instrument The power cord must be connected to a proper grounded source for electrical shock protection 45 CH1 Output BNC socket This output may be used to connect to a frequency counter or other instrument
62. r C2 cursor and tracking cursor 4 Rotate the VARIABLE control knob to position selected cursor Press one of the VARIABLE control knob to select FINE or COARSE cursor move speed 5 Read the measurement value on the screen Typical measurement readouts and applications are shown in Figure 5 16 The measurement values are automatically controlled by the VOLTS DIV and TIME DIV control settings Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL ee Figure 5 19 Cursor Measurement a Typical AV Voltage difference for Tx resem AC voltage wn oes nf When both CH1 and CH2 are turned on ALIA TA AL A the measurement value of CHI A V1 b Typical A T Time difference cursor Samm a i measurement for rise time a jd sos fc Proceed rise time or fall time a a measurement requiring some additional signal scaling by using the graticule rise time measurement aids Number 0 10 90 and 100 are etched near the left vertical graticule line Use the following steps as a guideline to in making rise time measurement c Typical 1 A T cursor function for frequency measurement When the two cursors are superimposed at two edge points of the one period waveform by the C1 C2 TRK and VARIABLE controls the measurement value is displayed in
63. re five basic elements must be included e Command header Distinguish commands e Command type Equal mark Sets instrument state Question mark Queries instrument state e Parameter if required Instrument states value e Target if required Some commands need to be assigned specific channel e Message terminator or separator Command Command Message Parameter Target terminator Header Type or separator 2 bytes 1 byte 3 bytes 1 byte 1 byte Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Here are some valid examples remote control commands not including message terminator V1i 010A H4 001 M2 IDN The following example includes the header type value for the parameter and target This command will set channel 1 vertical gain at 20mV DIV Vi 010A tse Command Header V1 t Command Type Parameters 010 Target A Note The GRS 60X2 is sensitive to the case of command characters All of the commands are uppercase 6 6 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Message Terminator and Message Separator As there is no signal of end message on RS232 bus therefore use LF Line Feed 0x 0A as message terminator When a series
64. rease The available range is from mV DIV up to 20V DIV The knob is automatically switched inactive if the related channel is switched off The deflection coefficients and additional information regarding the active channels are displayed in the readout VAR Pressing the VOLTS DIV control knob to select the VOLTS DIV function between attenuator and vernier variable The current setting is displayed by the gt symbol in the readout After switching on the VAR turn the VOLTS DIV control knob counterclockwise to reduce the signal height and the deflection coefficient becomes uncalibrated 19 CH1 AC DC 20 CH2 AC DC Pressing the pushbutton briefly to switch over from AC symbol to DC symbol input coupling The setting is displayed in the readout with the deflection coefficient 21 CH1 GND Px 10 22 CH2 GND P X 10 Pushbutton of two functions GND Each time when the pushbutton is pressed briefly the input of the vertical amplifier is grounded It is displayed in the readout as an earth ground symbol at m PX10 Pressing and holding the pushbutton to select the indicated deflection coefficient of the channel displayed in the readout between 1 1 and 10 1 The probe factor of 10 1 is displayed in the readout with the probe symbol PX 10 in front of channel indication When proceed cursor voltage measurement the probe factor will be automatically included 20 Artisan Technology Group Quality I
65. roup Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 3 INTEN Control knob REAL TIME Mode only The control knob is used for adjusting the traces intensity in the real time mode Turning the knob clockwise to increase the intensity while turning it counterclockwise to decrease the intensity 4 FOCUS The control knob effects both the trace and the readout sharply 5 CAL The terminal provides a reference signal of 0 5Vp p at 1kHz for probe adjustment 6 Ground Socket Banana Socket galvanically connected to safety earth This socket can be used a reference potential connection for DC and low frequency signal measurement purpose 7 TEXT ILLUM Control knob with a double function The pushbutton is for selecting the text readout intensity function or scale illumination function and indicates the letter TEXT or ILLUM in the readout Press the pushbutton for the following sequences TEXT ILLUM TEXT The TEXT ILLUM function is associated the VARIABLE 9 control knob Turning the knob clockwise to increase the text intensity or scale illumination while turning the knob counterclockwise to decrease it Pressing the knob to switch the TEXT ILLUM on or off In the STORAGE mode the brightness of the waveform on the screen can be controlled by the TE
66. scilloscope Figure 5 3 Function Check 40 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 2 M 4 Set both CH1 and CH2 COUPLING to GND 5 Use the CH1 and CH2 POSITION controls to align both traces on the center graticule 6 Open the CH2 INV by pressing and holding the pushbutton 7 Set to the ADD mode by pressing the ADD pushbutton briefly 8 Set both CH1 and CH2 COUPLING to DC 9 The figure 5 4 below shows a satisfactory display The display will show a flat trace located on the center graticule that confirms the channel balance and ADD offset function Figure 5 4 ADD mode 10 Turn off the ADD mode by pressing the ADD pushbutton briefly 11 Turn off the CH2 INV by pressing and holding the pushbutton Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL 5 5 Basic Operation Displaying CH1 or CH2 To display the signal from a signal channel pressing briefly the CH1 or CH2 pushbutton to set the oscilloscope to channel I or channel 2 Displaying CH1 and CH2 To display both signals at the same time proceed the following steps 1 Set the CHI and CH2 on The figure 5 5 below shows two synchronous waveforms in the both modes 2 Adjust
67. splay Target A gt Channel 1 B gt Channel 2 Probe v fale Parameters Bytes Vv 4 Target Sets or queries the probe attenuation factor Syntax V4 001B V4 A Arguments Parameters 000 1X 001 10X 76 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Target A Channel 1 B gt Channel 2 V VAR v 5 Parameters 3Bytes pi Target lv Ls 2 target Sets or queries the vertical VAR function of the specified channel Syntax V5 071A V5 B Arguments Parameters 001 uncalibrated Max to 71 uncalibrated Min gt Enable vertical VAR function and sets VAR value 000 calibrated gt Disable vertical VAR function Target A Channel 1 B gt Channel 2 Invert V 6 i Parameters 3Bytes E SATT e Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Ezom Sets or queries the invert function Syntax V6 001 V6 Arguments Parameters 000 Disable invert function 001 Enable invert function ADD Ly lal Parameters 3Bytes Pe ley Sets or queries the addition function Syntax V7 001 V7 Arguments Parameters 000 Disable the addition function 001 Enable the addition function Artis
68. the CH1 or CH2 POSITION control to position the two waveforms 3 Set the ALT CHOP button to CHOP mode if the waveforms are flickering Figure 5 5 Both typical waveforms Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL E Displaying the sum or difference of CH1 and CH2 To display the algebraic sum or difference of CH1 and CH2 proceed the following steps 1 Set the ADD button to ADD mode The figure 5 6 below shows the sum of the waveforms from figure 5 5 2 Set the CH2 INV on by pressing and holding the button if necessary to display the different waveform 3 Pressing and holding one of the VOLTS DIV control knob to set it to vernier variable Then adjust one channel to the other in the event of gain difference P10 5V P10 N t Sms CH1 AC Figure 5 6 Typical ADD waveform Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL E Comparing Frequency and phase X Y Operation To compare the frequency and phase between two signals by using the X Y mode The X Y waveform displays different amplitude frequency and phase The figure 5 7 shows a typical waveform made up of two signals that are of the same frequency and amplitude but approxim
69. ts are indicated in the readout as A V DIV X Y mode In the X Y mode the instrument is automatically set to AV measurement The deflection coefficient selected for each channel may be different thus as in DUAL mode the A V cursor measurement requires a channel selection Under channel 1 X signal measuring condition the cursor lines are displayed as vertical lines and the readout displays A VX Pressing the pushbutton select channel 2 Y signal measuring then the cursor lines are displayed as horizontal lines and the readout indicates AVY AT Two vertical cursors appear The time between the two cursors is calculated according to the setting of TIME DIV and displayed with 55 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL _ _ AT on the upper side of the CRT VAT Two vertical cursors appear The reciprocal of the time frequency between the two cursors is calculated with 1 AT on the upper side of the CRT C1 C2 TRK Pushbutton The cursor 1 cursor 2 and tracking can be selected by this button Pressing the pushbutton to select the cursors in sequence as follows C1 Moves the cursor 1 on the CRT C2 Moves the cursor 2 on the CRT TRK Simultaneously moves the cursor and cursor 2 with the interval between the two cursors unchanged 9 VARIABLE
70. ty must match the composite sync polarity i e 7J for negative sync to obtain TV field triggering on the vertical sync pulse TV H Start the main trace at the beginning of a video signal line The polarity must match the composite sync polarity to obtain TV line triggering on the horizontal sync pulse 33 SLOPE Pushbutton for the triggering slope Briefly pressing the pushbutton to select the slope of the signal which is used for triggering the time base generator Each time when the pushbutton is briefly pressed the slope direction will switch from falling edge to rising edge and vice versa The current setting is displayed in the readout under item source SLOPE coupling If in the TV trigger mode it is synchronized only when the sync signal is negative A LJ symbol is displayed in the readout Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL U 34 COUPLING Pressing the pushbutton to select the trigger coupling The actual setting is indicated by the readout source slope COUPLING Each time when the COUPLING pushbutton is pressed the trigger coupling changes in the sequence AC HFR LFR AC AC Attenuates trigger signal frequency components below 20Hz and blocks the DC component of the signal AC coupling is useful for triggering on AC waveforms that have a large DC offset l HFR Hi
71. up Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL _ _ ee TS5 lt Parameters 3bytes gt Trigger Slope T5 WA WB WC WD Dump Waveform W 0 9 M1 lt Parameters 3bytes gt Smooth M1 M2 lt Parameters 3bytes gt Average M2 M3 lt Parameters 3bytes gt MAG Interpolation M3 Real time O lt Parameters 3bytes gt Storage Ol O2 lt Parameters 3bytes gt RUN STOP 02 O3 lt Parameters 3bytes gt Text Intensity 03 O3 lt Parameters 3bytes gt 03 Ilumine Intensity 99 a Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL e Details of Command Reference Each command in this chapter will give a brief description The examples of each command will be provided and what query form might return Note Every command must add byte message terminator of LF 0x04 Common Commands IDN sti fol s Queries the unique identification code of instrument Return GW GRS60X2Z 0 V 1 10 Clear the output buffer data of instrument ULK Leto di fe Unlock front panel control ees cee Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS
72. urrent Harmonic Radiated Immunity EN 61000 3 2 2000 EN 61000 4 3 1996 Voltage Fluctuation Electrical Fast Transients EN 61000 3 3 1995 EN 61000 4 4 1995 Surge Immunity EN 61000 4 5 1995 Conducted Susceptibility EN 61000 4 6 1996 Power Frequency Magnetic Field EN 61000 4 8 1993 Voltage Dips Interrupts EN 61000 4 11 1994 Safety Low Voltage Equipment Directive 73 23 EEC amp amended by 93 68 EEC EN 61010 1 1993 A2 1995 IEC 1010 1 1990 A1 1992 A2 1995 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL CONTENTS PAGE 1 PRODUCT INTRODUCTION ccsssssssssssensetscsssecneesssesees 1 L DeScription iiscssciiccccnesicostsssstessecenccevexeseceusssarcevexs 1 PZ FOALUT Go ciscis caisciniss cicicsintn des cincaicinn abivtieds caiwecianeewebocaaiesieses 2 2 TECHNICAL SPECIFICATIONS 5 3 PRECAUTIONS BEFORE OPERATION ET 9 3 1 Unpacking the Oscilloscope 0 sssceeceececeeeeenees 9 3 2 Checking the Line Voltage ccsscssseeseeeeseneees 9 S S ENVirOn MONG sss cesses ssccdicapasccnesiscnaconeessaustesatass sees 10 3 4 Equipment Installation and Operation cesee 10 3 S CRT Intensity isisi irooniana iaia 10 3 6 Withstanding Voltage of Input Terminals 10 4 PANELINTRODUCTION ccccececcsseestereceeeneeetes l1 A 1 Front Panel
73. y modulated where pulse signal or time scale marks are required 9 LED indicator and buzzer alarm The LED s located in the front panel assist operation and indicated additional information Incorrect operation and the electrical end position of control knobs are indicated by a warning beep 10 SMD manufacturing technology The instrument is built by using the most advanced SMD technology so as to reduce the number of internal wiring and shorten the foil route on the pe board This will also greatly increase the high frequency performance and the reliability of the product 11 Compact size 275W X 130H x 370D mm and front panel layout groups for easy to use Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com GRS 6052 6032 OSCILLOSCOPE USER MANUAL Een 2 TECHNICAL SPECIFICATIONS 6 inch rectangular type with internal graticule Type 0 10 90 and 100 markers 8 x 10 DIV I DIV 1 cm Accelerating Potential Approx 10kV GRS 6052 2kV GRS 6032 INTEN and FOCUS Front panel control Z axis Input Sensitivity at least 5V REAL TIME mode Polarity positive going input decrease intensity only Usable frequency range DC to 2MHz Max input voltage 30V DC AC peak at 1kHz or less Input Impedance approx 33k Q GRS 6052 47k Q GRS 6032 ImV 2mV DIV 5 5mV 20V DIV 3 14 calibrated steps in 1 2 5 sequence Continuously variable to 1 2 5 approx of

Download Pdf Manuals

Related Search

Related Contents

Ikelite 6038.53 underwater camera housing  入札説明書等（PDF様式）  

Copyright © All rights reserved. Failed to retrieve file