Owner`s Manual - Fuller Brush Vacuums
Contents
1. cleaner and insert the plastic end of the hose assembly into the cleaning attachment opening Then connect the extension wand to the other end of the hose assembly Fig 3 O The Tidy Maid is equipped with on board cleaning tools including a metal telescopic Power Wand stretch hose dusting brush and a crevice tool 1 To use the cleaning tools lift the hose handle straight up from the vacuum Fig 1 2 Extend the wand by pulling the button back and pulling the smaller wand out of the larger wand Fig 2 3 Attach any of the on board tools to the end of the wand or if you do not need the wand any tool can be connected directly onto the hose handle How to Replace the Headlight Bulb and the Vacuum Belt CAUTION a First unplug the vacuum cleaner How to Remove the Bottom Plate 1 Place vacuum cleaner in the lowest position by stepping on the handle release pad and pulling back the handle twice Then turn the vacuum cleaner over exposing the underside 2 Remove the four screws holding the lower plate in place Fig 1 3 Now remove the bottom plate How to Replace the Bulb 1 Place vacuum cleaner in the low position and remove the bottom plate as described above 2 To remove the old bulb pull it straight out Fig 2 3 To install a new bulb press it in until it clicks into place These bulbs are standard size and may be obtained f2. tightly EET SN i Fig N How to Adjust the Handle The handle on this vacuum cleaner can be set to one of three positions upright middle or low How to Adjust the Handle 1 To release the handle step on the handle release pad on the left side of the vacuum cleaner nozzle and pull back the handle Fig 1 NO Upright position for storage or when cleaning tools are used Fig 2 Handle locks in this position 3 Middle position for normal cleaning Fig 3 K Low position for cleaning under fumiture Fig 4 Once in the middle position step on the handle release pad again and lower the handle to place the vacuum in the low position d ER a Fig 2 How to Change the Filters Your vacuum cleaner is equipped with a secondary filter and a HEPA filter These filters capture fine dust particles and protect the motor from dirt Accumulated dirt in the bag compartment will be collected on the filters and may restrict motor performance It is important to change the filters regularly approximately once a year or as needed How to Change the Secondary Filter 1 Unplug the vacuum cleaner Remove the bag compartment cover and remove the vacuum bag 2 Remove the secondary filter by sliding it out from under the bag supporter Fig 1 Se Insert a new filter replace
3. vacuum cleaner and insert the screw Make sure the screw is tightened securely Turn the upper cord storage hook to the upright position and wind the power cord around the cord storage hooks when storing the vacuum cleaner Fig 2 How to Release the Power Cord l 2 The upper cord storage hook has a quickrelease action To release the cord rotate the hook downward and the cord will drop off the handle for immediate use Fig 2 Return the hook to the upright position before attempting to rewind the cord On Off Switch Fig 2 l 2 To turn the vacuum on push the switch located on the side of the bag compartment to the position To turn the vacuum off push the switch located on the side of the bag compartment to the O position Cord Release On Off switch Always operate the vacuum cleaner with a vacuum bag installed Bags should be changed when they are 2 3 full How to Change the Vacuum Bag l Unplug the vacuum cleaner Remove the bag compartment cover Fig 1 Remove the bag from the bag holder Attach the new vacuum bag onto the bag holder Fig 2 Pull the bottom corners of the new vacuum bag out to expand the bag capacity Fig 3 Reinsert the tab on the end of the bag compartment cover into the groove on the bag compartment housing Press the bag compartment cover into place closing it
4. BRUSH CO OWNER S MANUAL FOR FULLER BRUSH TIDY MAID VACUUM 5S PES Thank you for purchasing this Fuller Brush Upright Vacuum To ensure the best results please read this manual first and keep it for future reference Important Safety Imstusions 464i desde beasGhuh GaSb db bi ee highest hd bbe deeds dsb d bh bh Sass 2 TwoWie Polarized Gla Savy yee dese ee ate tena See eae bee eet 6 eves egies eee oe as 3 Ponts OS iGOMON s pesare Le AGREES AoE HERE EE ASE AGRE AWADES 64 RG ERE AS EOE BER Ree TES 4 Replacement Bags and Filters anaa 4 How to Assemble and Operate the Vacuum 2 aaa 5 Plewie Conde ie Vacuum Bages 0225882 day os ae gede Dae SRi gah S aG p aia eed Resa e iei s 5 Howto Ader the MOIS eee raria Hae eee SE ee ee ey a re a epa eae 6 Howto Change the FING i chos g45n52seeh2esS4 dhs hed bbe ei sishc sede be area sees ieaes 6 Edge Cleaning Feature 264s dae de nee eh oe ae Eo os Lee EARS De EERE EER EA EO RARE S EEE ROE RR ADRESS 6 Automatic Self Adjusting Nozzle 2 4 c cye4 eb ed eed Feed obese ede eed ede ee dee ee hee eee sad ees 7 Optional Cleaning Tools Accessories eee 7 onboard Noel Cleaning e serea eae a ee a E AE E E AH E e Rae A a E 4 7 How to Replace the Headlight Bulb and the Vacuum Belt eee 8 Hoyvto Clean the Name Poses serpenter ceeds atave heb bee des tere eea a teens eeess cee 9 Thermal FUSE ProtechoNes erreari apet repa A OAS WE ESK OOSRASIREGEES LESS R SATE S LEHRER ET
5. COULD OCCUR IF USED OUTDOORS OR ON WET SURFACES 3 Do not allow to be used as a toy Close attention is necessary when used by or near children 4 Use only as described in this manual Use only manufacturer s recommended attachments 5 Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return it fo a service center 6 Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces 7 Don O t unplug by pulling on cord To unplug grasp the plug not the cord 8 Do not handle plug or appliance with wet hands 9 Turn off all controls before unplugging 10 Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow 1 Keep hair loose clothing fingers and all parts of body away from openings and moving parts 2 Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes 3 Do not use without vacuum bag and or filters in place 4 Use extra care when cleaning on stairs 5 Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present 6 Do not attempt to service the unit while appliance is plugged in Two Wire Polarized Cord
6. E 9 For Best Performance ke o c tateamdarka de knta miada a i e a ea hed oMeee thea hy araess oka 10 Customer s Record The model and serial numbers of this product may be found on the back side of the unit You should complete the enclosed warranty card and mail it back to us or register it online at www tullerbrushvacuums com as soon as possible for your protection Also note the model and serial numbers of your unit in the spaces provided below and retain this book as a permanent record of your purchase Model Number Serial Number Date Purchased Your Fuller Brush vacuum cleaner is a product of high quality materials and superior workmanship We urge you to read these operating instructions carefully before you use this vacuum cleaner in order to obtain the full performance and satisfaction it can offer you Save These Instructions Before you plug in your Fuller Brush vacuum cleaner make sure the voltage indicated on the rating plate located on the back of the vacuum cleaner is the same as your local supply IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE When using an electrical appliance basic precautions should always be followed including the following SAVE THESE INSTRUCTIONS WARNINGS 1o reduce the risk of fire electric shock or injury 1 Do not leave appliance unattended when plugged in Unplug from outlet when not in use and before servicing 2 WARNING ELECTRIC SHOCK
7. This product is equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact an electrician to replace the obsolete outlet Do not defeat the safety purpose of the polarized plug Parts Identification Quick cord release Handle tube Power cord Cord storage hooks Bag compartment cover latch On Off switch Easy carry ees handle telescopic power wand Ba Accessory g attachment compartment opening Tools Quick clean out port Headlight Quick Nozzle clean out hose ort Handle P release pad l Nozzle hose Furniture guard Self adjusting nozzle Thermal reset button Replacement Bags and Filters e Genuine Fuller Brush Vacuum Bags e Genuine Fuller Brush HEPA Filter Part FB 06181 6 per package Part FB 06288 Part FB 06163 12 per package e Genuine Fuller Brush Secondary Filter Part FB 06250 How to Assemble and Operate the Vacuum How to Attach the Handle to the Vacuum Cleaner The vacuum and the handle are packed separately l After first removing the handle screw slide the handle into the slots on top of the vacuum cleaner Fig 1 Line up the small hole on the handle with the small hole on the
8. al Reset Thermal Fuse Protector This thermal protector is designed to protect your vacuum cleaner from overheating due to restricted airflow i e clogged hose operating the vacuum without a bag Should this situation occur the thermal fuse protector will safely shut off your vacuum cleaner fo avoid any potential damage NOTE To determine that it was the thermal fuse protector that turned off your vacuum cleaner and not some other reason please refer to the vacuum cleaner s headlight If the headlight is on while the motor is off then the thermal fuse did safely shut down the motor f the headlight and motor are both off then there is some reason other than the thermal protector i e pulled plug the vacuum cleaner has shut down How to Reset the Thermal Fuse 1 Unplug the vacuum cleaner 2 Check for problem overtilled bag clog in hose clogged filters etc 3 Correct problem 4 locate tripped fuse the small white or red button located at the bottom of the back side of the main body roughly one inch to the right of the left wheel 5 Using a pencil paper clip or other pointy object push the reset button 6 Plug vacuum cleaner in and begin using Please contact your Fuller Brush retailer with any questions For Best Performance e Keep machine and all accessories clean and in good operating condition e Change vacuum bags when they are 2 3 full to maintain optimum cleaning efficiency e Change filters
9. rom most appliance repair shops 4 Replace the bottom plate with the four screws How to Replace the Belt 1 Turn the unit over and remove the bottom plate as described above Fig 1 2 Take out the agitator assembly and remove the belt Fig 3 3 Loop the new belt around the agitator pulley and the motor drive shaft 4 Reinsert the agitator assembly back into housing Fig 4 Turn the agitator assembly by hand making sure the belt is not twisted and all rotating parts move smoothly Fig 5 Make sure the arrows on the ends of the agitator are facing down into the nozzle 5 Press the bottom plate into place and fasten it with the four screws NOTE To ensure maximum cleaning efficiency check the belt regularly to ensure it is in good condition Replace the belt if it is stretched cracked or if excessive slipping is occurring NI Wa a How to Clean the Nozzle Hose CAUTION Unplug the vacuum cleaner How to Clean the Nozzle Hose 1 Remove the wand from the wand hose holder as shown on page 7 2 Squeeze the tabs on both sides of the quick clean out port and pull away from the vacuum Fig 1 So Check above and below the port opening for obstructions gt Remove any obstructions 5 Replace the quick clean out port by squeezing both tabs and pushing it back into the wand hose holder Thermal Fuse Protection Your Fuller Brush vacuum cleaner comes equipped with a Manu
10. the bag and bag compartment cover How to Change the HEPA Filter Unplug the vacuum cleaner Remove the bag compartment cover emove the HEPA filter from the front of the bag compartment Fig 2 Co nsert a new filter and replace the bag compartment cover Edge Cleaning Feature The edge cleaning feature provides improved cleaning of carpets near walls and stationary furniture For maximum edge cleaning position the right side of the vacuum from the user s perspective near walls or stationary furniture 6 Automatic Self Adjusting Nozzle Your Fuller Brush upright vacuum cleaner is designed with an Automatic Self Adjusting Nozzle No manual adjustments are required The height of the nozzle is instantly and automatically adjusted to carpet pile height This self adjusting feature allows the nozzle to float evenly over all carpet pile surfaces Optional Cleaning Tools Accessories 7 Piece Deluxe Attachment Kit Fig 1 1 5foot crushproof hose with curved handle Extension wand 2 pieces Dusting brush Crevice tool Upholstery tool Upholstery brush insert Deluxe floor brush 6 Piece Standard Attachment Kit Fig 2 7 4oot hose with curved handle Extension wand 2 pieces Dusting brush Crevice tool Upholstery tool Upholstery brush insert Connecting the hose assembly to the vacuum cleaner Open the lid located on the back side of the vacuum
11. when dirt is visible on them or every six months if someone in your home suffers from allergies Otherwise once a year should do for replacing the filters e Always use genuine bags filters and parts as use of other products may result in poor cleaning or filtration performance Fuller Brush filtration products are designed for maximum performance e Store machine carefully in dry area e For optimum cleaning performance and safety follow your owner s manual 10 BRUSH CO Fuller Brush Vacuum Cleaners PO Box 730 Fenton MO 63026 www fullerbrushvacuums com Should your vacuum ever need service simply call the retailer where the original purchase was made 2012 Fuller Brush Vacuum Cleaners
Download Pdf Manuals
Related Search