Comfee Seat
Contents
1. 9 1 Headrest With or Without Speakers To height adjust the headrest loosen the soft touch knob at top rear of seat a and adjust to height required tighten knob to secure For depth adjustment remove the headrest cover by pulling the two tabs off the poppers b Unscrew the 2 bolts on top of the headrest c and slide to required position Tighten bolts to secure and re attach headrest cover 9 2 Four Point Pelvic Belt Remove seatbase cushion by pulling tabs away from poppers underneath the rear of the seat and lifting cushion off Velcro strips Feed the 4 pelvic belt straps through camlock fittings a Pull the straps to the required position and clamp to secure Using the 2 adjustment straps at the centre buckle b pull to required position for final fitting 9 3 Armrests You have a choice of 3 armrest height positions To adjust armrest height pull the lever at the front below the gable a While pulling the lever lift the gable armrest assembly up to the required position Release the lever and the armrest will lock into the closest pre set height positions You have a choice of 4 angle adjustment positions for size 1 and a choice of 5 angle adjustment positions for size 2 and 3 To adjust the armrest angle push down on the lever at the rear below the gable b While pushing the lever hold the armrest at the rear c and push the armrest into the required position Release the lever and the armrest will2. as soap can clog your fabric 3 The cushion covers can be removed except for the armrests pommel and gables and machine washed at 40 C Line drying is recommended however they can be tumble dried at a low temperature Please remove foam from the following covers before washing a Headrest ensure you remove speakers before putting into washing machine if applicable Chest Laterals Backrest Cushion Seatbase Cushion e Padded Calf Support All other soft upholstery can be placed into the washing machine intact after removing bolts and fastenings Store these in a safe place and out of reach of children A200 4 All fabrics including non machine washable fabrics can also be cleaned by hand whilst in place When cleaning we recommend you use a non abrasive detergent 5 Staining should be removed as quickly as possible with absorbent cloth towels or a sponge Routine soap and warm water sponging is effective for ordinary soiling and minor spills Be careful not to over wet the fabric as this will cause the stain to spread 6 Antiseptic cleaning agents can be used on more stubborn stains These may require a safe solvent such as Isopropyl Alcohol or Mineral Spirit Ensure that cleaning products are fully removed Metal and Plastic Components 1 Soap and water or antibacterial spray can be used for daily cleaning 2 Do not use solvents to clean plastic or metal components 3 Make sure the product is
3. 00 01 149 1900 02 149 1900 03 149 1900 04 149 1900 05 149 1900 06 149 1900 07 149 1900 08 149 1900 09 149 1900 10 149 1900 11 149 1900 12 149 1900 13 149 2900 01 149 2900 02 149 2900 03 149 2900 04 149 2900 05 149 2900 06 149 2900 07 149 2900 08 149 2900 09 149 2900 10 149 2900 11 149 2900 12 149 2900 13 149 3900 01 149 3900 02 149 3900 03 Includes depth and width adjustable seatbase 4 lockable castors Tilt in space Push Handle Angle Adjustable Calf Support Accessory Shelf Padded Footplate User Manual S1 Comfee Seat Shell with 1 Piece Backrest S2 Comfee Seat Shell with 1 Piece Backrest S3 Comfee Seat Shell with 1 Piece Backrest Includes depth and width adjustable seatbase 4 lockable castors Tilt in space Push Handle Angle Adjustable Calf Support Accessory Shelf Padded Footplate User Manual S1 Comfee Seat Shell with 2 Piece Backrest S2 Comfee Seat Shell with 2 Piece Backrest S3 Comfee Seat Shell with 2 Piece Backrest Cushion Packs all fabric accessories will match your chosen colour cushion pack S1 Cushion Pack Sperrin Pink S1 Cushion Pack Sperrin Green S1 Cushion Pack Sperrin Blue S1 Cushion Pack Lagan Lime S1 Cushion Pack Lagan Blue S1 Cushion Pack Donard Red S1 Cushion Pack Avoca Lime S1 Cushion Pack Avoca Berry S1 Cushion Pack Avoca Natural S1 Cushion Pack Botanic Lime S1 Cushion Pack Botanic Silver S1 Cushion Pack Avoca Earth S1 Cushion Pack Black Incontinence
4. 1 Pommel Avoca Lime S1 Pommel Avoca Berry S1 Pommel Avoca Natural S1 Pommel Botanic Lime S1 Pommel Botanic Silver S1 Pommel Avoca Earth S1 Pommel Black Incontinence S2 Pommel S2 Pommel Sperrin Pink S2 Pommel Sperrin Green S2 Pommel Sperrin Blue S2 Pommel Lagan Lime S2 Pommel Lagan Blue S2 Pommel Donard Red S2 Pommel Avoca Lime S2 Pommel Avoca Berry S2 Pommel Avoca Natural S2 Pommel Botanic Lime S2 Pommel Botanic Silver S2 Pommel Avoca Earth S2 Pommel Black Incontinence S3 Pommel S3 Pommel Sperrin Pink S3 Pommel Sperrin Green S3 Pommel Sperrin Blue 149 3682 04 149 3682 05 149 3682 06 149 3682 07 149 3682 08 149 3682 09 149 3682 10 149 3682 11 149 3682 12 149 3682 13 149 1635 XX 149 1635 01 149 1635 02 149 1635 03 149 1635 04 149 1635 05 149 1635 06 149 1635 07 149 1635 08 149 1635 09 149 1635 10 149 1635 11 149 1635 12 149 1635 13 149 2635 XX 149 2635 01 149 2635 02 149 2635 03 149 2635 04 149 2635 05 149 2635 06 149 2635 07 149 2635 08 149 2635 09 149 2635 10 149 2635 11 149 2635 12 149 2635 13 149 1636 XX 149 1636 01 149 1636 02 149 1636 03 149 1636 04 149 1636 05 149 1636 06 149 1636 07 149 1636 08 S3 Pommel Lagan Lime S3 Pommel Lagan Blue S3 Pommel Donard Red S3 Pommel Avoca Lime S3 Pommel Avoca Berry S3 Pommel Avoca Natural S3 Pommel Botanic Lime S3 Pommel Botanic Silver S3 Pommel Avoca Earth S3 Pomm
5. 2636 XX 149 2636 01 149 2636 02 149 2636 03 149 2636 04 149 2636 05 149 2636 06 149 2636 07 149 2636 08 149 2636 09 149 2636 10 149 2636 11 149 2636 12 149 2636 13 149 1637 XX 149 1637 01 149 1637 02 149 1637 03 149 1637 04 149 1637 05 149 1637 06 149 1637 07 149 1637 08 149 1637 09 149 1637 10 149 1637 11 149 1637 12 149 1637 13 149 2637 XX 149 2637 01 149 2637 02 149 2637 03 149 2637 04 149 2637 05 149 2637 06 149 2637 07 149 2637 08 149 2637 09 149 2637 10 149 2637 11 149 2637 12 149 2637 13 S1 Headrest With Speakers Avoca Natural S1 Headrest With Speakers Botanic Lime S1 Headrest With Speakers Botanic Silver S1 Headrest with Speakers Avoca Earth S1 Headrest with Speakers Black Incontinence S2 3 Headrest With Speakers S2 3 Headrest With Speakers Sperrin Pink 2 3 Headrest With Speakers Sperrin Green 2 3 Headrest With Speakers Sperrin Blue 2 3 Headrest With Speakers Lagan Lime 2 3 Headrest With Speakers Lagan Blue 2 3 Headrest With Speakers Donard Red S2 3 Headrest With Speakers Avoca Lime 2 3 Headrest With Speakers Avoca Berry S2 3 Headrest With Speakers Avoca Natural 2 3 Headrest With Speakers Botanic Lime 2 3 Headrest With Speakers Botanic Silver 2 3 Headrest with Speakers Avoca Earth S2 3 Headrest with Speakers Black Incontinence S1 Calf Support Laterals S1 Calf Support Laterals Sperrin Pink S1 Calf Support Laterals Sperrin Green S1 Calf
6. Cover S2 Cushion Pack Sperrin Pink S2 Cushion Pack Sperrin Green S2 Cushion Pack Sperrin Blue S2 Cushion Pack Lagan Lime S2 Cushion Pack Lagan Blue S2 Cushion Pack Donard Red S2 Cushion Pack Avoca Lime S2 Cushion Pack Avoca Berry S2 Cushion Pack Avoca Natural S2 Cushion Pack Botanic Lime S2 Cushion Pack Botanic Silver S2 Cushion Pack Avoca Earth S2 Cushion Pack Black Incontinence Cover S3 Cushion Pack Sperrin Pink S3 Cushion Pack Sperrin Green S3 Cushion Pack Sperrin Blue 149 3900 04 149 3900 05 149 3900 06 149 3900 07 149 3900 08 149 3900 09 149 3900 10 149 3900 11 149 3900 12 149 3900 13 149 1648 149 2648 149 3648 149 1649 14 149 2649 14 149 3649 14 149 1649 15 149 2649 15 149 3649 15 149 1672 XX 149 1672 01 149 1672 02 149 1672 03 149 1672 04 149 1672 05 149 1672 06 149 1672 07 149 1672 08 149 1672 09 149 1672 10 149 1672 11 149 1672 12 149 1672 13 149 2672 XX 149 2672 01 149 2672 02 149 2672 03 149 2672 04 149 2672 05 149 2672 06 149 2672 07 149 2672 08 149 2672 09 149 2672 10 149 2672 11 149 2672 12 149 2672 13 S3 Cushion Pack Lagan Lime S3 Cushion Pack Lagan Blue S3 Cushion Pack Donard Red S3 Cushion Pack Avoca Lime S3 Cushion Pack Avoca Berry S3 Cushion Pack Avoca Natural S3 Cushion Pack Botanic Lime S3 Cushion Pack Botanic Silver S3 Cushion Pack Avoca Earth S3Cushion Pack Black Incontinence Cover S1 Wooden Tray S2
7. LECKEY Comfee Seat User Instructions The award winning Comfee Seat is an innovative supportive and practical seating system designed specifically for leisure time in the home school or in respite care It comes in 3 sizes with adjustable back height seat depth and an innovative seat width adjustment mechanism using the unique armrest design to accommodate users from ages 4 to adult This manual shows you how you can quickly and easily make use of all the functions The instructions on the safety and maintenance of the product will ensure that you will enjoy the use of this product for a long time Contents 01 Intended Use 02 Declaration of Conformity 03 Terms of Warranty 04 Product History Record 05 Product Training 06 Safety Information 07 How to Unpack and Assemble 08 Fitting the Covers 09 Clinical Setup for Postural Management 10 Frequent Adjustments for Daily Use 11 Cleaning and Care Information 12 Daily Product Inspections 13 Annual Product Inspections 14 Reissuing Leckey Products 15 Product Servicing 16 Technical Information 17 Accessories 1 Intended Use The Comfee Seat comes in 3 size options catering for the needs of children and adults with disabilities As a guide size 1 is for children aged 4 10 Size 2 is for children aged 9 16 and size 3 is for children aged 15 Adult Maximum weight guides are 50kg 75kg and 100kg respectively 2 Declaration of Conformity James Leckey Desi
8. Support Laterals Sperrin Blue S1 Calf Support Laterals Lagan Lime S1 Calf Support Laterals Lagan Blue S1 Calf Support Laterals Donard Red S1 Calf Support Laterals Avoca Lime S1 Calf Support Laterals Avoca Berry S1 Calf Support Laterals Avoca Natural S1 Calf Support Laterals Botanic Lime S1 Calf Support Laterals Botanic Silver S1 Calf Support Laterals Avoca Earth S1 Calf Support Laterals Black Incontinence 2 3 Calf Support Laterals 2 3 Calf Support Laterals Sperrin Pink 2 3 Calf Support Laterals Sperrin Green 2 3 Calf Support Laterals Sperrin Blue 2 3 Calf Support Laterals Lagan Lime 2 3 Calf Support Laterals Lagan Blue 2 3 Calf Support Laterals Donard Red 2 3 Calf Support Laterals Avoca Lime 2 3 Calf Support Laterals Avoca Berry 2 3 Calf Support Laterals Avoca Natural 2 3 Calf Support Laterals Botanic Lime 2 3 Calf Support Laterals Botanic Silver 2 3 Calf Support Laterals Avoca Earth 2 3 Calf Support Laterals Black Incontinence 149 X638 149 1638 149 2638 149 3638 149 X901 149 1901 149 2901 149 3901 Seat Protector Black S1 Seat Protector S2 Seat Protector S3 Seat Protector Padded Footstraps Black Neoprene S1 Padded Footstraps S2 Padded Footstraps S3 Padded Footstraps O Leckey T 028 9260 0750 19 Ballinderry Road F 028 9260 0799 Lisburn E info leckey com BT28 2SA W www leckey com Northern Ireland ern Irelan United Kingdom y Tube 24 h
9. Wooden Tray S3 Wooden Tray S1 Padded Tray Cover Grey S2 Padded Tray Cover Grey S3 Padded Tray Cover Grey S1 Padded Tray Cover Black S2 Padded Tray Cover Black S3 Padded Tray Cover Black Small Flipaway Lateral Supports Pair Small Flipaway Lateral Supports Sperrin Pink Small Flipaway Lateral Supports Sperrin Green Small Flipaway Lateral Supports Sperrin Blue Small Flipaway Lateral Supports Lagan Lime Small Flipaway Lateral Supports Lagan Blue Small Flipaway Lateral Supports Donard Red Small Flipaway Lateral Supports Avoca Lime Small Flipaway Lateral Supports Avoca Berry Small Flipaway Lateral Supports Avoca Natural Small Flipaway Lateral Supports Botanic Lime Small Flipaway Lateral Supports Botanic Silver Small Flipaway Lateral Supports Avoca Earth Small Flipaway Lateral Supports Black Incontinence Medium Flipaway Lateral Supports Pair Medium Flipaway Lateral Supports Sperrin Pink Medium Flipaway Lateral Supports Sperrin Green Medium Flipaway Lateral Supports Sperrin Blue Medium Flipaway Lateral Supports Lagan Lime Medium Flipaway Lateral Supports Lagan Blue Medium Flipaway Lateral Supports Donard Red Medium Flipaway Lateral Supports Avoca Lime Medium Flipaway Lateral Supports Avoca Berry Medium Flipaway Lateral Supports Avoca Natural Medium Flipaway Lateral Supports Botanic Lime Medium Flipaway Lateral Supports Botanic Silver Medium Flipaway Lateral Supports Avoca Earth M
10. adjust the height of the footplate for size 1 and 2 slide the centre footplate bar into footplate receiver behind the calf support to the required height Tighten the soft touch knob on the footplate receiver to secure a For size 3 slide the 2 footplate bars into the 2 footplate receivers behind the calf support to the required height Tighten the soft touch knob on each footplate receiver to secure To angle adjust the padded footplate use your Leckey Tool Locate the bolt underneath the padded footplate inside the slot in the material b Adjust the angle by turning the bolt clockwise or anti clockwise depending on angle required 10 8 Padded Footplate Straps To remove padded footplate straps pull velcro strip away from the strap To secure the padded footstrap around the user pull the velcro strip tightly and secure to the strap 10 9 Flipaway Laterals To Flipaway the laterals pull and hold the knob a until the lateral has flipped away Release the knob to lock into position 11 Cleaning amp Care Information How to Maintain When cleaning we recommend that you use only warm water and a non abrasive detergent Never use organic solvents or dry cleaning fluids Upholstery and fabrics 1 Clean and care for your fabric on a regular basis Simply vacuum to remove dust particles and wipe with a damp cloth for general cleaning 2 Microfibre cloths are extremely effective without soap which is helpful
11. ction Leckey recommend that a written record is maintained of all those who have been trained in the correct use of this product 6 Safety Information A 6 1 Always read instructions fully before use A 6 2 Users should not be left unattended at any time whilst using Leckey equipment A 6 3 Only use Leckey approved components with your product Never modify the product in any way Failure to follow instructions may put the user or carer at risk and will invalidate the warranty on the product A 6 4 If in any doubt as to the continued safe use of your product or if any parts should fail please cease using the product and contact our customer services department or local dealer as soon as possible A 6 5 Carry out all positional adjustments and ensure that they are securely fastened before you put the user into this product Some adjustments may require the use of a tool which is provided with each product Keep all tools out of reach of children A 6 6 When placing the user into the seat for safety reasons always secure the pelvic harness first A 6 7 When the product is stationary ensure that all four castors are locked and facing away from the base This is especially important when the tilt and space and back recline facility is in use 6 8 When the seat is in use please ensure that the height adjustment pedal or bolts and tilt in space are locked off and cannot be adjusted accidentally espec
12. dry before use Wooden Components Check all wooden components regularly to ensure there are no cracks or splinters 1 Wipe clean with warm soaping water followed by a clean water rinse Do not use strong detergents abrasive products organic solvents or dry cleaning fluids Heavily ingrained soiling may be removed by scrubbing with a soft brush 12 Daily Product Inspection Therapists Parents and Carers We recommend that daily visual checks of the equipment are carried out by therapists carers or parents to ensure the product is safe for use The recommended daily checks are detailed below 1 Ensure all adjustment knobs and bolts are in place and secure 2 Check all upholstery wood and velcro for signs of wear and tear 3 Check all castors are moving freely and lock securely 4 Ensure the 4 point pelvic harness is fully secured around the user and they cannot slide or creep forward in the seat 5 Ensure the footplate is attached securely A If in any doubt to the continued safe use of your Leckey product or if any parts should fail please cease using the product and contact our customer service department or your local dealer as soon as possible 13 Annual Product Inspection Therapist Technician Leckey Product Advisor Dealer Leckey recommend that each product should be subject to a detailed inspection at least once a year and every time the product is reissued for use This inspection sh
13. eadrest Insert the speakers into the 2 x pockets in the lining of the headrest Pull the speakers cable out through the rear pocket to connect to your device which can be stored in the top pocket of the headrest cover 8 2 Fitting the Back Support Cushions Insert the foam into the backrest cushion ensuring the profile of the foam is in the correct position Zip to secure Place the backrest cushion into position and secure by pulling the 4 tabs to the rear of the wooden backrest and pressing on to poppers a _ LAYS SW LLL a 8 3 Fitting the Seat Base Cushion Before fitting the seat base cushion ensure the calf support cushion has been fitted first Insert the foam into the seatbase cover ensuring the profile of the foam is in the correct position Zip to secure Push the seatbase cushion towards the rear of the seat base and secure by pulling tabs underneath the back of the seat base and attaching to poppers a Press the seatbase cushion down into position and securing the front using the Velcro strips on top of the calf support cushion b 8 4 Fitting the Flipaway Chest Lateral Cushions Slide the flipaway lateral cover over the foam ensuring the profile of the foam is in the correct position The lateral bracket should slide into the centre section of the foam a Zip to secure from both the top and bottom of the flipaway lateral cushion b 8 5 Fitting the 4 Point Pelvic Belt Remove seatbase cushi
14. edium Flipaway Lateral Supports Black Incontinence 149 3672 XX 149 3672 01 149 3672 02 149 3672 03 149 3672 04 149 3672 05 149 3672 06 149 3672 07 149 3672 08 149 3672 09 149 3672 10 149 3672 11 149 3672 12 149 3672 13 149 1682 XX 149 1682 01 149 1682 02 149 1682 03 149 1682 04 149 1682 05 149 1682 06 149 1682 07 149 1682 08 149 1682 09 149 1682 10 149 1682 11 149 1682 12 149 1682 13 149 2682 XX 149 2682 01 149 2682 02 149 2682 03 149 2682 04 149 2682 05 149 2682 06 149 2682 07 149 2682 08 149 2682 09 149 2682 10 149 2682 11 149 2682 12 149 2682 13 149 3682 XX 149 3682 01 149 3682 02 149 3682 03 Large Flipaway Lateral Supports Pair Large Flipaway Lateral Supports Sperrin Pink Large Flipaway Lateral Supports Sperrin Green Large Flipaway Lateral Supports Sperrin Blue Large Flipaway Lateral Supports Lagan Lime Large Flipaway Lateral Supports Lagan Blue Large Flipaway Lateral Supports Donard Red Large Flipaway Lateral Supports Avoca Lime Large Flipaway Lateral Supports Avoca Berry Large Flipaway Lateral Supports Avoca Natural Large Flipaway Lateral Supports Botanic Lime Large Flipaway Lateral Supports Botanic Silver Large Flipaway Lateral Supports Avoca Earth Large Flipaway Lateral Supports Black Incontinence S1 Pommel S1 Pommel Sperrin Pink S1 Pommel Sperrin Green S1 Pommel Sperrin Blue S1 Pommel Lagan Lime S1 Pommel Lagan Blue S1 Pommel Donard Red S
15. el Black Incontinence Size 1 Standard Headrest S1 Standard Headrest Sperrin Pink S1 Standard Headrest Sperrin Green S1 Standard Headrest Sperrin Blue S1 Standard Headrest Lagan Lime 1 Standard Headrest Lagan Blue S1 Standard Headrest Donard Red S1 Standard Headrest Avoca Lime S1 Standard Headrest Avoca Berry S1 Standard Headrest Avoca Natural S1 Standard Headrest Botanic Lime S1 Standard Headrest Botanic Silver S1 Standard Headrest Avoca Earth S1 Standard Headrest Black Incontinence S2 3 Standard Headrest 2 3 Standard Headrest Sperrin Pink 2 3 Standard Headrest Sperrin Green 2 3 Standard Headrest Sperrin Blue 2 3 Standard Headrest Lagan Lime S2 3 Standard Headrest Lagan Blue S2 3 Standard Headrest Donard Red S2 3 Standard Headrest Avoca Lime 2 3 Standard Headrest Avoca Berry S2 3 Standard Headrest Avoca Natural S2 3 Standard Headrest Botanic Lime S2 3 Standard Headrest Botanic Silver S2 3 Standard Headrest Avoca Earth S2 3 Standard Headrest Black Incontinence S1 Headrest With Speakers S1 Headrest With Speakers Sperrin Pink S1 Headrest With Speakers Sperrin Green S1 Headrest With Speakers Sperrin Blue S1 Headrest With Speakers Lagan Lime S1 Headrest With Speakers Lagan Blue S1 Headrest With Speakers Donard Red S1 Headrest With Speakers Avoca Lime S1 Headrest With Speakers Avoca Berry 149 1636 09 149 1636 10 149 1636 11 149 1636 12 149 1636 13 149
16. gn Ltd as manufacturer with sole responsibility declares that the Leckey Comfee Seat conforms to the requirements of the 93 42 EEC Guidelines and EN12182 Technical aids for disabled persons general requirements and test methods 3 Terms of Warranty The Warranty applies only when the product is used according to the specified conditions and for the intended purposes following all manufacturer s recommendations also see general terms of sales delivery and payment A two year warranty is provided on all Leckey manufactured products and components 4 Product History Record Your Leckey product is classified as a Class 1 Medical device and as such should only be prescribed set up or reissued for use by a technically competent person who has been trained in the use of this product Leckey recommend that a written record is maintained to provide details of all setups reissue inspections and annual inspections of this product 5 Product Training Record Clients amp Carers Your Leckey product is a prescribed Class 1 Medical Device and as such Leckey recommend that parents teachers and carers using the equipment should be made aware of the following sections of this user manual by a technically competent person Section 6 Safety Information Section 9 Clinical Setup for postural management Section 10 Frequent adjustment for daily use Section 11 Cleaning amp Care Information Section 12 Daily Product Inspe
17. he top pocket of the headrest cover A Be careful not to trap fingers when sliding headrest bars into the receivers 7 2 Attaching the Flipaway Chest Laterals Remove top backrest cushion by pulling tabs away from poppers at the rear of the backrest Align the two holes in lateral bracket to the slot in the metal plate at the centre of the backrest a Align the washer between the metal plate and the wood insert screw through the rear of backrest through the full assembly b Secure with nut at the front of the assembly Note this is easier to attach when the seat is tilted backwards 7 3 Attaching the 4 point pelvic belt Remove seatbase cushion by pulling tabs away from poppers underneath the rear of the seat and lifting cushion off Velcro strips Feed the 4 pelvic belt straps through camlock fittings a and clamp to secure 7 4 Attaching the tray Before you insert the tray make sure the tray lock lever is unlocked a Align tray bars with the two tray receivers Push tray into required position and secure by pulling the tray lock lever at each side away from each tray bar b 7 5 Attaching the Tray Cover Slide tray cover on from the rear and snap the 2 poppers underneath the tray to secure a Pull the tray cover across to the front of the tray and secure using 2 poppers underneath the front of the tray 7 6 Attaching the Gables Put the Comfee Seat into full recline and tilt the armrest i
18. ially if there are children in the area A 6 9 The Comfee Seat is not a wheelchair and although mobility is a feature of the seat we do not recommend that users be moved over uneven surfaces whilst in the equipment All due care and attention should be taken if transporting the user from one seat to another A 6 10 The Comfee Seat has not been crash tested therefore cannot be used in transport 6 11 Never leave the product on a sloping surface greater than 5 degrees Always remember to lock all the castors 6 12 Only use the push handle to steer and move the seat from one area to another Never use the tray for this purpose 6 13 The product contains components which could present a choking hazard to small children Always check that locking knobs and bolts within the child s reach are tightened and secure at all times A 6 14 Leckey products comply with fire safety regulations in accordance with EN12182 However the product contains plastic components and therefore should be kept away from all direct sources of heat including naked flames cigarettes electric and gas heaters 6 15 Never place hot items on the Activity Tray as they may damage the plastic 6 16 Clean the product regularly Do not use abrasive cleaners Carry out maintenance checks on a regular basis to ensure your product is in good working condition A 6 17 The product is designed for indoor use and when not in use should be stored in a d
19. ide the 2 footplate bars into the 2 footplate receivers behind the calf support to the required height Tighten the soft touch knob on each footplate receiver to secure 7 10 Attaching the Padded Footstraps Unzip the padded footplate cover for ease of use For size 1 and size 2 thread the strap through the slot in the cover and wooden footplate a Align the popper on the wooden foot plate to the strap and press to secure Thread strap up through the wooden foot plate and cover b Secure and tighten around the foot using the velcro strap Repeat process for second strap c For size 3 thread the strap through the required slot in the cover bracket and wooden footplate Thread strap up through the wooden foot plate and cover Secure and tighten around the foot using the velcro strap Repeat process for second strap Wut Fitting the Cushions 8 1 Fitting the Head Support Cushion with or without Speakers Slide the headrest cover over the headrest foam ensuring the contoured section of foam is at the top of the cover and the flat section of foam is at the bottom of the cover Zip to secure Slide the flap of material at the rear of the cover with no zip on to the bottom of the wooden headrest assembly a Pull the 2 tabs across the top of the wooden headrest and secure using poppers underneath b To insert speakers only if you have ordered optional headrest with speakers open the zip at the rear of the h
20. lock into the closest pre set angle position 9 4 Seat Depth Width Fully tilt seat for ease of access To adjust the depth of the seat base loosen the 2 knobs below the seat base at either side a Use the grab handle on the wooden section of the seat base and move into required position b Tighten the 2 knobs to secure To width adjust the seat base adjust the armrest angle as described in section 9 3 9 5 One Piece Backrest To adjust the angle on the one piece backrest pull the trigger attached to the left of the push handle Whilst holding in the trigger adjust the backrest to the required angle Release the trigger to lock into position 9 6 Two Piece Backrest To adjust the angle on the two piece backrest pull the trigger attached to the left of the push handle a Whilst holding in the trigger adjust the backrest to the required angle Release the trigger to lock into position To height adjust the two piece backrest loosen the soft touch knob at the bottom of the top wooden section b Move backrest to required height and tighten using the soft touch knob A Use the push handle to move the backrest to the required height Do not place hands at the bottom of the backrest as fingers may get trapped 9 7 Flipaway Chest Laterals To adjust the height of the Flipaway chest laterals remove the covers and unscrew the 2 bolts using your Leckey tool a Adjust the bracket to the required positi
21. n minimum width and maximum height position and take off the lower backrest cushion for ease of access Lift the gable arm on to the 2 x bolts underneath the armrest a Attach the Leckey plate and secure assembly with furniture connectors b Screw bolt through metal plate into gable c to secure at bottom To secure the rear tilt the seat backwards lift the armrest to the highest position and screw bolt through metal plate into gable d 7 7 Attaching the Pommel Move the calf support into the 90 position for ease of access The calf support can be adjusted to any position after the pommel is inserted Locate the slot at the centre of the seat base underneath it you will find a pull pin Pull the pin down and slide the pommel into the slot a There are 3 depth options available and the pommel will click into the closest pre set position when you release the pull pin 7 8 Attaching the Calf Support Laterals Remove calf support cushion for ease of access Locate the 2 holes on each side of the wooden calf support a Align the calf support lateral bracket with the holes at the rear of the calf support Thread bolt through full assembly and use washer and nut to secure b 7 9 Attaching the Padded Footplate For size 1 and 2 slide the centre footplate bar into footplate receiver behind the calf support to the required height Tighten the soft touch knob on the footplate receiver to secure a For size 3 sl
22. nformation on Leckey distributors please visit our website www leckey com 16 Technical Information Size 1 2 3 mm kg inches Ibs mm kg inches Ibs mm kg inches Ibs Max User Weight 50kgs 110lbs 75kg 165lbs 100kgs 220lbs Seat Width 210 320mm 8 3 12 6 220 395mm 8 7 15 6 330 485mm 13 19 Seat Depth 250 380mm 9 8 15 340 460mm 13 4 18 1 390 520mm 15 4 20 5 Seat Height 425mm 16 7 490mm 19 3 540mm 21 3 Backrest Height from Seatbase 550 600mm_ 21 7 23 6 670 740mm 26 4 29 1 750 820mm_ 29 5 32 3 Footplate Distance from Seat 260 350mm 10 2 13 8 310 410mm 12 2 16 1 355 460mm_ 13 9 18 1 Armrest Tray Height 175 230mm 6 9 9 1 205 290mm 8 1 11 4 230 300mm 9 0 11 8 Tilt In Space degrees 0 to 30 0 to 30 0 to 30 Backrest Recline degrees 98 to 128 98 to 128 98 to 128 Calf Support Angle degrees 11 to 32 22 to 40 16 to 41 Footprint 870 x 710mm 34 2x28 945 x 760mm 37 2x29 9 1000x785mm 39 4x30 9 Seat Weight 38kg 84lbs 48kg 106lbs 60kg 132lbs All international service enquiries should be directed to the appropriate Leckey distributor who will be delighted to assist you For further information on Leckey distributors please visit our website www leckey com Accessories 149 X600 149 1600 149 2600 149 3600 149 X601 149 1601 149 2601 149 3601 149 X900 XX 149 19
23. ntre buckle for final fitting 10 3 Tilt in Space Locate the lever at the rear of the wooden backrest at the top right a Pull to the right and tilt the seat to the required position Release the lever to lock 10 4 Tray Before you insert the tray make sure the tray lock lever is unlocked a Align tray bars with the two tray receivers Push tray into required position and secure by pulling the tray lock lever at each side away from each tray bar b To unlock the tray push the tray lock levers away from the tray bars 10 5 Armrests You have a choice of 3 armrest height positions To adjust armrest height pull the lever at the front below the gable a While pulling the lever lift the gable armrest assembly up to the required position Release the lever and the armrest will lock into the closest pre set height position You have a choice of 5 angle adjustments for the size 2 and 3 and a choice of 4 angle adjustments for the size 1 To adjust the armrest angle push down on the lever at the rear below the gable b While pushing the lever hold the armrest at the rear c and push the armrest into the required position Release the lever and the armrest will lock into the closest pre set angle position 10 6 Calf Support Locate the lever at the left hand side of the calf support a Pull the lever while adjusting the calf support to the required angle Release the lever to lock 10 7 Padded Footplate To
24. on and tighten bolts to secure To adjust the width of the Flipaway laterals insert your Leckey tool inside the slots at the rear of the backrest b Loosen the bolts on each lateral bracket slide into required position and re tighten to secure To Flipaway the laterals pull and hold the knob until the lateral has flipped away Release the knob to lock into position Be careful not to nip fingers when using the flipaway laterals 9 8 Pommel To adjust the pommel move the calf support into the 90 deg position for ease of access The calf support can be adjusted to any position after the pommel is inserted Locate the slot at the centre of the seat base underneath it you will find a pull pin Pull the pin down and slide the pommel into the slot a There are 3 depth options available and the pommel will click into the closest pre set position when you release the pull pin 9 9 Tilt in Space Locate the lever at the rear of the wooden backrest at the top right a Pull to the right and tilt the seat to the required position Release the lever to lock 9 10 Calf Support Locate the lever at the left hand side of the calf support a Pull the lever while adjusting the calf support to the required angle Release the lever to lock 9 11 Padded Footplate To adjust the height of the footplate for size 1 and 2 slide the centre footplate bar into uU S mMm e n footplate receiver behind the calf support to the requi
25. on by pulling tabs away from poppers underneath the rear of the seat and lifting cushion off Velcro strips Feed the 4 pelvic belt straps through camlock fittings a and clamp to secure 8 6 Fitting the Calf Support Cushion Slide the calf support cushion over the foam ensuring the soft sponge side of the foam is facing the front Zip cushion to secure Locate the 4 poppers on top of the wooden seat base and attach each tab a Pull the 2 tabs at the bottom of the calf support cushion and attach to the 2 poppers underneath the wooden calf support 8 7 Fitting the Calf Support Lateral Cushions Slide the calf support lateral cover over the foam ensuring the profile of the foam is in the correct position The lateral bracket should slide into the centre section of the foam a Zip to secure from both the top and bottom of the calf support lateral cushion 8 8 Fitting the Padded Footplate Cushion Slide the padded footplate cushion on to the wooden footplate Zip to secure at each side a linical etup for ostural anagemen The clinical setup of the product should be completed by a technically and clinically competent person who has been trained in the use of the product Leckey recommend that a written record is maintained of all clinical setups for this product Set the backrest height seat depth and footplate height before placing the child in the seat These can be fine tuned when the child is in the seat
26. ould be carried out by a technically competent person who has been trained in the use of the product and should include the following checks as a minimum requirement 1 Check all ratchet handles knobs nuts bolts and plastic buckles are in place replacing any missing items Paying particular attention to the following items gt Headsupport soft touch knob gt Backrest height and angle adjustment levers gt Seat depth adjustment knobs gt Pelvic harness hip guide attachment bolts gt Footrest height and angle adjustment 2 Lift the base to check each castor individually Make sure they are moving freely and remove any dirt from the rubber wheels Check that the brakes lock the wheels securely 3 Visually check the structure of the product paying attention to weld points on the frame ensuring there are no signs of fatigue or cracking around the welds 4 Leckey recommend that a written record is maintained of all annual product inspections If in any doubt to the continued safe use of your Leckey product or if any parts should fail please cease using the product and contact our customer service department or your local dealer as soon as possible 14 Re issuing Leckey Products Most Leckey products are assessed and ordered to meet the needs of an individual user Before reissuing a product we recommend that the therapist prescribing the product has carried out an equipment compatibility check for the new u
27. our postural care for babies kids amp adults Sleeping Sitting Standing Walking Moving Bathing Toileting
28. red height Tighten the soft touch knob on the footplate receiver to secure a For size 3 slide the 2 footplate bars into the O r a fi S e 2 footplate receivers behind the calf support to the required height Tighten the soft touch knob on each footplate receiver to secure To angle adjust the padded footplate use e E a p sts your Leckey Tool Locate the bolt underneath the padded footplate inside the slot in the material b Adjust the angle by turning the bolt clockwise or anti clockwise depending on angle required Parents and carers should be shown how to make frequent adjustments and be made aware of the safety checks in section 6 by a technically and clinically competent person who has been trained in the use of the product Leckey recommend that a written record is maintained of all parent and carers who have been trained in the use of this product 10 1 Transferring Into and Out of the Comfee Seat To prepare the seat for transfer move the 4 point pelvic belt away from the seat base area by tucking straps between rear of armrest and the backrest cushion To flip up the footplate lift up and push towards the calf support a The footplate will remain in this position until pushed back down into position 10 2 Adjusting the 4 Point Pelvic Harness To open and close the 4 point pelvic harness use the central release buckle a Pull to required position using the 2 adjustment straps at the ce
29. ry place that is not subjected to extremes of temperature The safe operating temperature range of the product is 5 to 40 Celsius 1 or 2 piece Headrest backrest each option has 2x cushions Flipaway 4 Point Laterals Padded Belt Tray Pommel Furniture Receiver Connector Armrests Gables Calf Support Lateral Calf Accessory Support Shelf Footplate Straps Padded Footplate Lockable Castors How to unpack an assemble Check parts Congratulations on purchasing your Comfee Seat All of the parts will be contained in polythene bags with each one clearly labelled Carefully remove them from the boxes and check all the parts you have ordered A Keep polythene bags away from children Multitool A limited number of adjustments will require the use of a multitool which is supplied with your seat Where instructions state left or right it is from the user s perspective 7 1 Attaching the head support with or without speakers Loosen the soft touch knob at top rear or seat a Insert the headrest bars into receivers at top of seat b Adjust to height required tighten knob to secure To insert speakers only if you have ordered optional headrest with speakers open the zip at the rear of the headrest Insert the speakers into the 2 x pockets in the lining of the headrest Pull the speakers cable out through the rear pocket to connect to your device which can be stored in t
30. ser and has ensured that the product being re issued contains no modifications or special attachments A detailed technical inspection should be carried out on the product prior to re issuing This should be carried out by a technically competent person who has been trained in the use and inspection of the product Please refer to section 13 for the required checks to be carried out Ensure the product has been cleaned thoroughly in accordance with section 11 of this manual Ensure a copy of the user manual is supplied with the product A copy can be downloaded from our website www leckey com Leckey recommend that a written record is maintained of all product inspections carried out during the reissue of the product If in any doubt to the continued safe use of your Leckey product or if any parts should fail please cease using the product and contact our customer service department or your local dealer as soon as possible 15 Product Servicing Servicing of all Leckey products should only be carried out by technically competent persons who have been trained in the use of the product In the UK amp ROI please contact the Leckey Service Centre on UK 0800 318265 or ROI 1800 626020 and our customer service department will be delighted to assist you with your servicing requirements All international service enquiries should be directed to the appropriate Leckey distributor who will be delighted to assist you For further i
Download Pdf Manuals
Related Search