Nilfisk C 120.2 Nilfisk C 125.2
Contents
1. amp Clean the connectors of dust and sand Make sure that no sand or dirt is blocking the movement of the pawl on the Click amp Clean spray lance Rinse ac cording to requirement Rinse the detergent spraying attachment after use amp Clean the nozzles Any repair should always be made in an authorized work shop with original spare parts Clean the water inlet filter regularly once a month or more frequently according to use Carefully loosen the filter with a screwdriver and clean it Check that it is intact before re mount ing it The inlet filter must always be fitted inside the water inlet pipe to filter out sand limestone and other impurities as they will damage the pump valves CAUTION Failure to fit the filter will invalidate the guarantee 12 7 2 Cleaning of nozzle 7 3 Cleaning of machine vents 7 4 Greasing of couplings A clogging up in the nozzle Causes a pump pressure which is too high This is why cleaning is required immediately 1 Stop the machine and dis connect the nozzle 2 Clean the nozzle IMPOR TANT The cleaning tool 11 should only be used when the nozzle is detached 3 Flush the nozzle backwards with water The machine should be kept clean so as to let cooling air pass freely through the ma chine vents To ensure an easy connec tion and that o rings do not dry up the couplings should be greased regularly 13 EN EN 8 Trouble shoo2. to avoid a hazard Mains power connection O The following should be ob served when connecting the high pressure washer to the electric installation amp The electric installation shall be made by a certified elec trician and comply with IEC 364 t is recommended that the electric supply to this appli ance should include either a residual current device that will interrupt the supply if the leakage current to earth ex ceeds 30 mA for 30 ms amp The permissible modulus of power supply impedance lt 0 332 Q Water connection amp Connection to the public mains according to regula tions amp Inlet hose can be connected to the water mains with a max inlet pressure of 10 bars This high pres sure washer is only allowed to be connected with the drinking water mains when an appropriate backflow preventer has been installed Type BA ac cording to EN 1717 The back flow preventer can be ordered under number 106411177 The length of the hose between the backflow preventer and the high pressure washer must be at least 10 metres to absorb pos sible pressure peaks min diam eter inch Operation by suction for ex ample from a rainwater vessel is carried out without backflow preventer Recommended suc tion set 126411387 As soon as water has flown through the BA valve this water is not considered to be drinking water any more IMPORTANT Only use wa ter without any impurities If
3. and high pressure hose 6 3 Storage of accessories The machine should be stored in a frost free room Pump hose and accessories should always be emptied of water prior to storing as follows 1 Stop the machine press the start stop switch O 1 and detach water hose and accessory 2 Restart the machine and activate the trigger Let the machine run until no more water runs through the spray gun 3 Stop the machine unplug and wind up hose and cable 4 Place spray handle nozzles and other accessories in the holders of the machine Should the machine by mistake be frozen it will be necessary to check it for damage NEVER START UP A FROZEN MACHINE Frost damages are not covered by the guarantee To avoid accidents the electric cable and the high pressure hose should always be winded carefully up 1 Wind up the electric cable on the appropriate hooks The standard accessories nozzles a spray handle b spray lance c foam sprayer d can be stored on the pres sure washer The nozzle cleaning tool e can also be stored on the product 11 EN 7 Maintenance 7 1 Cleaning of water inlet filter WARNING Always disconnect the electrical plug from the socket prior to maintenance or cleaning To ensure a long and problem free working life please take the following advice Wash out water hose high pressure hose spray lance and accessories before mounting
4. machine to run with open trigger until regular working pressure resumes Check that the water supply corresponds to specifications required see model tag NB Avoid using long thin hoses min 1 2 Clean the nozzle see section 7 2 Clean the filter see section 7 1 Straighten out hose Contact your nearest Nilfisk Service Centre Wait for pump hoses or accessory to thaw Connect inlet water Clean the filter see section 7 1 Clean the nozzle see section 7 2 In case problems other than the above occur please contact your local Nilfisk distributor 14 9 Further information 9 1 Recycling the washer 9 2 Warranty conditions Make the old cleaner unusable immediately 1 Unplug the cleaner and cut the electric cable Do not discard electrical appli ances with household waste Nilfisk guarantees high pres sure washers for domestic use for 2 years If your high pres sure washer or accessories are handed in for repair a copy of the receipt must be enclosed Guarantee repairs are being made on the following condi tions amp that defects are attributable to flaws or defects in materi als or workmanship wear and tear as well as misuse are not covered by the guarantee amp that the directions of this instruction manual have been thoroughly observed amp that repair has not been carried out or attempted by other than Nilfisk trained service staff amp that only original accessorie
5. there is a risk of running sands in the inlet water i e from your own well an additional filter should be mounted Safety devices Pressure safety device The unloader valve can reduce pressure if it exceeds pre set values Locking device on spray gun 7a see illustration at the end of this manual The spray gun features a lock ing device When the pawl is activated the spray gun cannot be operated Thermal sensor A thermal sensor protects the motor against overloading The machine will restart after a few minutes when the thermal sen sor has cooled 2 Description 2 1 Application 2 2 Operation elements and model survey 23 This high pressure washer has been developed for domestic use within Car motorbike boat cara van trailer patio drive flag stones woodwork brickwork barbecue garden furniture lawn mower Section 5 describes the use of See illustration at the end of this manual Start stop switch Water inlet with filter 2a High pressure connection High pressure hose Electric cable Click amp Clean spray lance Spray gun with lock 7a Click amp Clean Tornado PR nozzle Click amp Clean Powerspeed nozzle CONOOBRWDN the high pressure washer for various cleaning jobs Only use the high pressure washer for purposes described in this manual The safety precautions must be observed to prevent damage to the machine the surface to be cleaned o
6. to regulations 2 Attach the nozzle Warning When attaching the Click amp Clean nozzles the pawl on the side of the spray lance 6 should come out again Note The Torna 23 do PR nozzle 8 and the foam sprayer 10 fea ture a swivel lock which must be positioned in the hole in the Click amp Clean spray lance 6 Press the pawl to detach the Click amp Clean nozzle IMPORTANT Only use wa ter without any impurities If there is a risk of running sands in the inlet water i e from your own well an additional filter 106411231 should be mounted 1 Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrat ing the machine Note Check that the filter is fitted in the water inlet pipe and that it is not clogged up 2 Connect the water hose to the water supply by means of the quick connector inlet water max pressure 10 bar max temperature 40 C 3 Turn on the water EN EN 4 4 Start and stop of the machine when connected to a water supply 4 5 Pressure regulation on the TORNADO PR nozzle The spray lance is affected by a thrust during operation therefore always hold it firmly with both hands IMPORTANT Point the nozzle at the ground Check that the machine is in upright position NOTE Do not place the machine in high grass 2 Release the trigger lock 7a 3 Activate the trigger o
7. AN Nilfisk C 120 2 Nilfisk C 125 2 EN User Manual ru Copyright 2008 Nilfisk Index 1 Safety precautions and warnings 3 2 DOC nen 5 3 Before you start using your pressure Washer sanna11en010n 6 4 Operating your pressure washer rrrrrrrnnrrrnnnrrnnnrrvanerrnnrnvnnennnn 8 5 Fields of Application and Working Methods 9 6 After using your pressure washer 11 NANNA iana 12 8 Trouble Shooting icccaciiiwiiarnicnccsondeccinetniertmemetansiewaeraeapsceonians odie 14 9 Fe NAMN ea 15 10 Main technical data rrnnrnnnonnrrnnrnannnnrvnnennnrnannnnernnnnannnnennnene 17 L PENN 18 1 Safety Precautions and Warnings r Symbols used to mark in structions Do not let people who have not been trained in the use of a high pressure washer nor read the instruction manual operate the machine This appliance is not intended for use by children or other persons without assistance or supervision if their physical sensory or mental capabili ties prevent them from using it safely Children should be su pervised to ensure that they do not play with the appliance Before starting up your machine please check it carefully for any defects If you find any do not start up your machine and con Before starting up your high pressure washer for the first time this instruction manual must be
8. ayer Wash before the soap dries Another more effective and quicker method is to use the Patio Cleaner Thus you will also avoid splashes Apply Wood Cleaner and wash before the soap dries NOTE Use the garden brush to clean off the dirt Same method as for flagstones but be careful bad joints and wood may be damaged by high pressure You may choose only to use the Tornado nozzle Adjust the distance pressure to the quality of the joints and the wood Patio Cleaner can also be used on vertical surfaces Wash the gutter with the nozzle Always wash towards downpipes Beware not to spray under the roofing Push the tube cleaner approx m to mark into a tube or drain and activate the trigger of the spray handle The nozzle opening turning backwards will pull the cleaner through the tube The nozzle will break down the plug and flush the dirt backwards Mount the water sand blasting equipment and rust and paint is efficiently and quickly removed Beware not to damage the surface to be sandblasted Wash with high pressure and maybe a brush You may use Stone amp Wood Cleaner to remove moss and algae Rinse the worst dirt off with the nozzle Apply Metal Cleaner with the foam sprayer and let it act for approx 5 min Wash with the nozzle You may use the multiangle adaptor for hard to get at areas to avoid splashing 10 6 After using your pressure washer 6 1 Storing the washer 6 2 Winding up of electric cable
9. duct is in direct contact with the dirt Detergents are applied from bottom to top for example on a car bodywork in order to avoid super clean areas where the detergent collects in higher concentration and streams downwards Let the detergent work for several minutes before rinsing but never let it dry on the surface be ing cleaned Note It is important that the detergents do not dry up Otherwise the surface that has to be cleaned can be damaged In order to break down tough layers of dirt additional mechanical effect may be required Special wash brushes offer this supplemen tary effect that cuts through dirt especially by car washing EN EN 5 2 Typical fields of application Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer from Nilfisk in association with accessories and detergents Task Car Rims alu minium Flagstones concrete floors and other hard Surfaces Garden furniture wood Brickwork Wood work Gutter Cleaning of drain pipes out lets down pipes etc Rust paint Green house Garden tools lawn mover Accessories Click amp Clean Car nozzle auto brush undercarriage nozzle Foam sprayer Car Combi Cleaner Rim brush auto nozzle atomizer Alu Cleaner Powerspeed nozzle Stone amp Wood Cleaner Patio Cleaner Wood Cleaner Garden brush Powerspeed nozzle Stone amp Wood Clean
10. ectrical power supply before carrying out user maintenance To ensure the appliance safety only use original spare parts from the manufacturer or approved by the manufac turer amp High pressure hoses fittings and couplings are important for the safety of the appli ance Only use hoses fittings and couplings recommended by the manufacturer amp Do not use the appliance if a Supply cord or impor tant parts of appliance are damaged e g safety device high pressure hose and trig ger gun amp The appliance is intended to clean cars and garden etc Appropriate ear protection has to be used amp Never use the machine in an environment where there could be a danger of explo sion If any doubt arises please contact the local authorities It is not allowed to clean as bestos containing surfaces with high pressure amp This high pressure washer must not be used at tempera tures below 0 C WARNING Inadequate extension cables can be dangerous Cables on drums should always be com pletely uncoiled to prevent the cable from overheating If an extension cable is used the plug and the socket must be waterproof and comply with the below mentioned requirements for length and cable dimen sions 1 0mm2 max 12 5m 1 5mm2 max 20 m 2 5mm2 max 30 m f the electric cable is damaged it must be re placed by the manufacturer or his service agent or simi larly qualified person in order
11. er Patio Cleaner Undercarriage nozzle Tube cleaner Water sandblasting equipment Tornado PR nozzle brush Stone amp Wood Cleaner Tornado PR nozzle Power speed nozzle multiangle adaptor Metal Cleaner Cleaning method 1 Apply Car Combi Cleaner with the foam sprayer Always start from the bottom and work upwards Let Car Combi Cleaner act for at least 5 min 2 Wash the car with the car nozzle which has been optimized for quick and gentle cleaning of enamelled surfaces the jet is wider and not so sharp Start at the front of the car and work back wards to avoid water from penetrating by the door mouldings 3 U se the brush for removal of traffic film which is not removed by the nozzle If the car is very dirty apply Car Combi Cleaner again 4 Attach the undercarriage nozzle and clean undercarriage and wheel arches 5 Remove water from the surface of the car with the scraper on the car brush Make sure that all grains of sand etc have been removed before using the scraper Wipe with a wash leather where the scraper cannot reach Apply Alu Cleaner with an automizer Let it act for approx 5 min and wash with the rim brush For steel rims use Car Combi Cleaner Use the foam sprayer and wash with rim brush Be careful The high pressure jet may damage the tyres Wash towards outlets or the like On surfaces with moss or algae you may start by applying Stone amp Wood Cleaner with the foam spr
12. f the spray gun 7 and let the water run until all air has escaped from the water hose 4 Press the Start stop switch I 1 5 Activate the trigger of the spray gun 7 Always adjust the distance and thus the pressure of the nozzle to the surface which is to be cleaned Low pressure Do not cover the machine during operation or use it in a room without adequate ventila tion Note If the ma chine is left or not used for 5 minutes it must be switched off on the start stop switch O 1 1 Press the start stop switch O 1 2 Disconnect the electrical plug from the socket 3 Shut off the water supply and activate the trigger to relieve the machine of pressure 4 Lock the spray gun 7a When releasing the trigger of the spray gun the machine automatically stops The ma chine will start again when you re activate the spray gun The pressure can be regulated on the TORNADO PR nozzle 8 5 Fields of application and working methods 5 1 General 5 1 1 5 1 2 Detergent and foam Mechanical effect Efficient high pressure cleaning is achieved by following a few guidelines combined with your own personal experience of specific cleaning tasks Accessories and detergents when correctly cho sen can increase the efficiency of your pressure washer Here is some basic information about cleaning Foam or detergent should be applied onto dry surfaces so that the chemical pro
13. of grease and oil on motors for instance Applied with an atomizer For cleaning of wooden surfaces incl of wooden garden furniture 10 Main Technical Data Type C 120 2 6 Permissible pressure bar MPa max 120 12 0 17 EN 11 Declaration Declaration Manufacturer s name and address or his authorized Nilfisk Advance AG representative in the Community Nilfisk Business Unit Guido Oberdorfer Str 10 89287 Bellenberg GERMANY Name of the person responsible for the technical Wolfgang Nieuwkamp documentation Description of the equipment High pressure washer Equipment name Nilfisk Model C 120 2 Dimension 280 x 270 x 820 mm Rated output voltage AC 230 240 V Rated frequency 50 Hz Rated input power 1 65 kW Other Measured sound power level 90 dB A Guaranteed sound power level 92 dB A Declaration The equipment refer in this document fulfils all the requirements of the Directive Machine Directive 98 37 EC Low voltage Directive 73 23 EEC EN 60335 2 79 2004 EN 60335 1 A1 2004 EN 50366 2003 EMC Directive 89 336 EEC EN 55014 1 A2 2002 EN 55014 2 A1 2001 EN 61000 3 2 A2 2005 EN 61000 3 3 A1 2001 Outdoor Noise Directive 2000 14 EC Place and date of the declaration Bellenberg November 10 2005 18 Nilfisk Division of Nilfisk Advance A S Industrivej 1 DK 9560 Hadsund tel 45 7218 2100 128303201 a 01 2008
14. r severe personal injuries 10 Click amp Clean foam sprayer 11 Nozzle cleaning tool 12 Trolley handle 13 Hose hook 14 Model tag 15 Hook for electric cable Specifications See model tag 14 of machine We reserve the right to alter the specifications 3 Before you start using your pressure washer 3 1 Mounting of trolley handle 1 Place the trolley handle 12 on the machine 2 Secure the handle by mount ing the 2 screws EN 3 2 Mounting of quick coupling 3 3 Mounting of high pressure hose 4 1 Connection of high pressure hose 1 Screw the quick coupling tight on to the water inlet 2 Note The inlet filter 2a must always be fitted in the water inlet pipe to filter out sand lime stone and other impurities as these will damage the pump valves Caution Failure to fit the filter will invalidate the guarantee Attach the high pressure hose 4 to the spray gun 7 Detach the high pressure hose by pressing the pawl A 1 Mount the high pressure hose on the outlet 3 4 2 Mounting of spray lance and Click amp Clean nozzles 4 3 Water connection 23 1 Push the spray lance 6 into the spray gun 7 and screw it on Note The spray lance 6 has a built in low pressure nozzle that can be used for flushing away dirt An ordinary 1 2 garden hose of min 10 m and max 25 m will be suitable NOTE Connection to the public mains according
15. read through carefully Save the instructions for later use Safety instructions marked with this symbol must be observed to pre vent danger to persons tact your Nilfisk distributor Especially check amp The insulation of the electric cable should be faultless and without any cracks If the electric cable is damaged an authorized Nilfisk distributor should replace it WARNING amp High pressure jets can be dangerous Never direct the water jet at persons pets live electrical equipment or the machine itself amp Never try to clean clothes or footwear on yourself or other persons amp Hold the spray lance firmly with both hands The spray lance is affected by a thrust This symbol is used to mark safety instructions that must be ob served to prevent damage to the ma chine and its performance This symbol indicates tips and instructions to simplify work and to ensure a safe operation of up to 16 4 N during ope ration The operator and anyone in the immediate vicinity of the site of cleaning should take action to protect themselves from being struck by debris dislodged during operation Wear goggles and protection clothes during operation amp This appliance has been de signed for use with cleaning agents supplied or recom mended by the manufacturer The use of other cleaning agents or chemicals may adversely affect the safety of the appliance amp Disconnect from el
16. s have been applied amp that the product has not been exposed to abuse such as knocks bumps or frost amp that only water without any impurities has been used As specified in European Direc tive 2002 96 EC on old electri cal and electronic appliances used electrical goods must be collected separately and recycled ecologically Contact your local authorities or your nearest dealer for further information that the high pressure washer has not been used for rental nor used commer cially in any other way Repairs under this guarantee include replacement of defec tive parts exclusive of packing and postage carriage Besides we refer to your national law of sale The machine should be for warded to one of the service centres of the Nilfisk organisa tion with description specifica tion of the fault Repairs not covered by the guarantee conditions will be invoiced l e malfunctions due to Causes mentioned in section Troubleshooting Chart of the instruction manual In order that Nilfisk can render you optimum service you should register your product on our web site www nilfisk alto com under PRODUCT REGI STRATION 15 EN 9 3 Accessories Only use original accessories Click amp Clean Special nozzle for enameled surfaces Optimal distance 30 Car nozzle 50 cm Click amp Clean 90 angled special nozzle for undercarriage and wheel arches Undershassis Integrated g
17. ting To avoid unnecessary disappointments you should check the following before contacting the Nilfisk service organization symptom Cause Recommended action Machine refuses to start Machine not plugged in Defective socket Fuse has blown Defective extension cable Fluctuating pressure Pump sucking air Valves dirty worn out or stuck Pump seals worn out Fuse has blown Incorrect mains voltage Machine stops Thermal sensor activated Nozzle partially blocked Fuse blows Fuse too small Machine pulsating Air in inlet hose pump Inadequate supply of mains water Nozzle partially blocked Water filter blocked Hose kinked Machine often starts and stops by itself Pump spray gun is leaking Machine starts but no water comes out frozen No water supply Water filter blocked Nozzle blocked Pump hoses or accessory Plug in machine Try another socket Replace fuse Switch off other machines Try without the extension cable Check that hoses and connections are air tight Clean and replace or refer to local Nilfisk distributor Clean and replace or refer to local Nilfisk distributor Replace fuse Switch off other machines Check that the mains voltage corresponds to specification on the model tag Leave the washer for 5 minutes to cool down Clean the nozzle see section 7 2 Change to an installation higher than the amp consumption of the machine You may try without the extension cable Allow
18. uide shoes nozzle Click amp Clean Adjusted in angles from 0 90 for better working posture and Multiangle cleaning of hard to get at places as for instance barrels or the adaptor underside of the lawn mower Fits all nozzles Click amp Clean For cars and other surfaces Available in more shapes Brushes Extension hose 7 m extension hose increasing the working range Underchassis Special spray lance for washing your car underneath spray lance Drain amp Tube 15 m long tube cleaner for the cleaning of tubes and drains cleaner Water sand For removal of paint and rust Sand available from do it your blasting equip self shops ment Patio Plus Equipment for quick cleaning of patio drive flagstones Garden brush Rotary brush for cleaning of wooden surfaces Rim brush Rotary brush for cleaning of wheel rims Wall hook For storage of machine on wall Rotary brush For cleaning vehicles and other surfaces Water suction kit For removal of large amounts of water from e g garden pounds 16 Detergents Stone amp Wood Cleaner Plastic Cleaner Metal Cleaner Car Combi Cleaner Alu Cleaner Oil amp Grease Cleaner Wood Cleaner For flagstones brick and woodwork Suitable for moss and algae For plastic and synthetic materials such as garden furniture For cleaning of metal such as garden tools For cars etc With rinsing wax For surfaces of aluminium Applied with an atomizer For cleaning
Download Pdf Manuals
Related Search