user manual - Save on Security Systems, Inc.
Contents
1. Sonic Alert WIRELESS DOORBELL amp TELEPHONE SIGNALER MODEL DB200 SONIC ALERT S 5 YEAR LIMITED WARRANTY The Wireless Doorbell Signaler Model DB200 is warranted against manufacturing defects in materials and workmanship for two 5 years from the date of purchase Within this period Sonic Alert will repair or eplace at our option the DB200 without charge for parts and labor Simply send the DB200 postpaid and a copy of your sales slip as proof of purchase to Sonic Alert Inc OPERATION The state of the art Doorbell Signaler will alert you when someone comes to visit The Doorbell Signaler Model DB200 is the only doorbell and intercom signaler that requires no wires and can be installed in seconds DB200 will alert you that someone is at your door by flashing a light plugged into the base unit or any Sonic Alert receiver anywhere in your home The DB200 is designed to work with homes with or without an existing doorbell or chime and all existing buzzer and intercom systems Other features include selectable number of flashes 5 or 10 different flash code for front door rear door or intercom Additional sensors sold separately for 2 door or source There is also a built in chime for hearing members of the family can be turned off by using the switch on the right side of the DB200 The DB200 receives an RF radio signal from the DB200 sensor and flashes the light plugged into the built in outlet of the DB2002. and 4 thru 6 are set in the OFF position If you need to change the dip switch settings to avoid interference with your neighbors make sure you change both the DB200 Signaler to match the DB Sensor b The 8 switch determines the number of flashes when someone is at your door In the ON position your until will flash 5 times and in the OFF position your unit will flash 10 times This feature is wonderful when you have an extra sensor for the back door One sensor would be set in the ON position and the other would be set in the OFF position c The 7 switch is for use when using 2 sensors this switch determines the settings for front or back door If using for one door only set this switch in the ON position At this setting your unit will flash at a fast rate and will make a ding dong sound If using 2 sensors one for the front door and one for the back door the setting for the 2 sensor would be in the OFF position In this position the front door will flash at a different flash rate than the back door In the OFF position your back door sensor will flash at a slow rate with a dong dong sound Function settings The function switch on the back of DB sensor smaller unit should be set depending on which installation application you need See diagram on back Switch position Top Intercom Buzzer System Wireless Chime Box Installation see 3 amp 4 Center Outside Doorbell Button Only see 1 amp 2 Bottom Hard W
3. Use a 300 watt or less incandescent lamp only The DB200 can send a signal to all Sonic Alert remote receivers Note Must be used only with Sonic Alert receivers for proper operation other manufacturers products are not reliable with our products This device complies with Part 15 of the FCC Rules and with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications not expressively approved by the party responsible for compliance could void user s authority to operate the equipment SIGNALER DB SENSOR INSTALLATION To install the DB200 follow the diagrams and instructions on the following page that match the type of installation you need for your home If the installation follows diagrams 1 4 a 9 volt alkaline battery is required in the DB sensor Please check the switches on your DB200 Sensor before installing Do not change switches 1 6 these are pre set It s very important that the switch settings on both units match See figure 1 1 on back side for settings DB Sensor settings smaller unit 1 thru 6 dip switches are set at the factory and only need to be changed if your neighbor has a DB200 or DB100 The 8 dip switches should be set as follows a 1 thru 3 dip switches are set in the ON position
4. ired to Existing Doorbell chime Box Installation see 5 vas Pa By Se DB200 Signaler larger of the 2 units ee The speaker switch allows you to turn the SES Audio Alarm ON or OFF ON is up and 7 OFF is Down The Dip Switches 1 6 should match the DB Sensor Dip switches 1 6 The factory setting is 1 thru 3 ON and 4 thru 6 OFF The 7 and 8 switches are not active switches and it will not matter if they are set to ON or OFF unless your using 2 sensors one for the front and one for the back door If you need to change the dip switch settings to avoid interference with your neighbors make sure both units 1 Wireless Installation 2 Wired Doorbell Installation 1 Attach sensor to 1 Connect cocraell dulsida ef door tutun lo sensor 2 Plug signaler imo with provided wal outlet wire 3 Plug lamp into 2 Plug signaler into sigraler wall outlet 3 Plug lam iato signalar 1 Attach sensur to intercom 1 Attach sensor tc 2 Plug signaler inta cocrtell chime wall outlet 2 Ploy signuler inklu 3 Plug lamp inte wall outlet signaler 3 Plug lamp into signaler Wire sensor nto chime fer battery loss operation i ete Plug sigveler into Detail of step 1 wall outlet i hae ta Installation 5 siynalar settings match Dip Switch settings DB 200 Wahaa inja 123 45 67 8 Figure 1 1 Multi Function Input Jack Located on the left side of the DB Sensor this input jack is for installatio
5. ns as shown in diagram 2 amp 5 Troubleshooting amp Help If you ve followed the directions and are still having problems please try the following suggestions 1 Check battery in the sensor must be an 9 volt alkaline type 2 Check that dip switch settings 1 6 match both the sensor and the signaler as shown in figure 1 1 above 3 Check outlet for power 4 Move the Signaler to an outlet closer to the sensor unit 5 If using the Multi Function input jack make sure that the wires are not touching each other See diagram number 2 amp 5 for proper installation 6 Check Function setting switch for proper position Warranty Thank you for purchasing this high quality Sonic Alert product we hope you will have many years of satisfied use All Sonic Alert products come with a limited 5 year warranty so please retain your receipt in safe place for possible future reference you will need in the event of warranty service Sonic Alert Inc REV 1 1
Download Pdf Manuals
Related Search