BX-S1 User Manual
Contents
1. When mounting the Bell Box please take note of the following points Mount on the external wall at a prominent location Mount as high as possible out of easy reach Tamper Switch The Bell Box is protected by a tamper switch which will be activated if the Bell Box is removed from the mounted location or its cover opened When installing the Bell Box please make sure the tamper switch is properly compressed against the wall and the front cover is secured with screw Before installing the Bell Box changing mounting location or batteries please make sure to disable the tamper switch temporarily using your Control Panel s Siren Tamper function and enable the tamper switch again after finish working on the Bell Box Please refer to your Control Panel manual for detail Siren Audible Performance The siren produces a minimum of 104 dBA sound pressure at 1 meter range when activated For Burglar and Panic Alarm the Bell Box gives a continuous alarm sound For Fire Water alarm the Bell Box gives an intermittent alarm sound of 2 sec siren followed by a 1 sec interval The siren is silenced when either the programmed siren length expires or when the Control Panel is disarmed to turn off the siren Please refer to Dip Switch table above to set your desired alarm length through Dip Switch SW3 and SW4 setting Strobe LED Light When the Bell Box is activated the LED strobe light will also flash to indicate the Bell B2. sound a beep to indicate the tamper is disabled 2 Remove the front cover 3 Remove the four screws fixing the battery compartment and take off the compartment lid 4 Remove the old batteries and press the Tamper Switch twice to discharge 5 Insert the new D cell alkaline batteries into the battery compartment according to correct polarity 6 The Bell Box will emit beeps and flash when the last battery is inserted 7 Replace the battery compartment lid and front cover 8 Enable the tamper protection function through your Control Panel The Bell Box will sound a beep to indicate Specification Environmental Condition 10 C to 40 C relative humidity 85 non condensing Radio 433 MHz FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FCC Caution To assure continued compliance any changes or modifications not expressly approved by the party responsible for compliance may void the user s authority to operate this equipment Example use only shielded interface cables when connecting to computer or peripheral devices BLAUPUNKT
3. Wireless Outdoor Bell Box BX S1 Parts Description 1 Mounting Holes x 4 2 Tamper Switch The tamper switch protects the device from being opened or from being removed from mounting surface 3 Function Switch Block Contains 7 DIP Switches to enable the learning mode and to set the alarm period of siren and strobe light 4 Power Switch To enable disable the power supply 5 Securing Screw 6 LEDs Package Content 1 x Outdoor Bell Box 4 x large wall plugs and screws 4 x 1 5V D alkaline batteries Dip Switch swt Sirentearning OO eee Oooo O Normal operation Oo Learn in mode SS a Strobe Activation ore only during siren alarm period _ ON ee until alarm is disarmed SW3 Siren Duration OFF 3 min 5 min 10 min 1 second test Reserved Memory Reset Normal Clear Memor Supervision ae Supervision function disable C oon Supervision function enable For further detail please see Learning and Operaion ON ON N swe O O O O O FE CE D ES 5 6 Learning 1 Open the front cover and locate the Function Switch Block 2 Use a sharp object to set Dip SW3 amp SW4 on the function switch block to your desired alarm length 3 Enter learning mode for your control panel 4 Slide the Power Switch to ON position to power on the Bellbox 5 Slide Dip SW1 to the ON position The Bell Box LED 1 amp 3 will flash once with a short beep The BX S1 is now in learning mod
4. e After 3 seconds the Bell Box will send out a learning code the LED 1 amp 3 will flash once to confirm 6 If the Control Panel receives the learning signal please refer to the Control Panel manual to complete the learning process When learning is complete the Control Panel will send signal to the Bell Box to confirm The Bell Box will sound a short beep and LED 1 amp 3 will flash once to indicate learning is successful 7 If the Control Panel fails receive a learning code slide Dip SW1 back to OFF and then ON position again to enter learning mode again 8 If the Bell Box does not respond please remove the Bell Box from the control panel and repeat steps 3 6 again 9 Slide Dip SW1 to the OFF position to leave learning mode If you do not slide Dip SW1 back to OFF position the Bell Box will automatically leave the learning mode in one hour Installation The Outdoor Bell Box has 4 mounting holes on the back cover for wall mounting Mounting Holes x4 Before Installation refer to your Control Panel manual to temporarily disable the Siren Tamper function to avoid accidental alarm trigger BLAUPUNKT 1 Use the 4 mounting holes on the back to mark position on the wall Drill holes into the wall using the mounting holes as template Fix the base onto the wall with the screw and plugs provided Replace the front cover onto the base GY ee Enable the Siren Tamper function on you Control Panel
5. ox is alarming The duration of strobe light flash is determined by Dip Switch SW2 setting When set to OFF the strobe light will flash according to the alarm length set by Dip Switch SW3 and SW4 When set to ON the strobe light will flash after the alarm length has expired until the control panel is disarmed Audio amp Visual Status Indication Table The Bell Box will activate its siren and strobe light to notify the user of system status please refer to below table Strobe light indication Disarm Arm Low Battery Disarm Low Battery Arm Tamper Disarm Tamper Previous alarm warning Tamper Alarm Entry Exit Sound FECE AS 3 LED flashes at once Sequentially flashes for 1 cycle 3 LED flashes for three times Sequentially flashes for 2 cycles 3 LED flashes for three times Sequentially flashes for 2 cycles Sequentially flashes for 2 cycles Sequentially flashes Siren Audio indication will be effected by the Confirmation ON OFF setting in your Control Panel settings Battery The Bell Box uses four 1 5V D alkaline batteries as its power source It also features low battery detection function to notify the Control Panel when battery voltage is low When the Bell box is on low battery follow the procedure below to change the batteries 1 Temporarily disable the Bell Box s tamper protection function please refer to your Control Panel manual for detail The Bell Box will
Download Pdf Manuals
Related Search