English-FC Series-With magnetic module-NOVA
Contents
1. Rear maintenance space is more than 800mm from front to back Tools list for installation choice depends on the practical jobsite 1 Diagonal cutting plier 2 Combination plier 3 Screw drivers CV NAE a ES Cut the wire Cut the steel wire rope Installtiles and power supply 4 L shape spanners 5 End wrench tool set 6 Adjustable wrench Tighten or loosen the screw Install tiles 7 Socket wrench Digi i 9 Rubber hammer A Assemble the s screen Measure voltage or current Adjust the gap between tiles Other tools for installation choice depends on the practical jobsite mes em ict O Haemeswe le o 22 FC series User Manual 4 2 Setup Process of Rear Standing Installation A Warning The height of FC tiles depends on the height of supporting steel structure and the display surface has to obtain the flatness within a tolerance zone of 0 2mm and keep perpendicular to the reference surfaced Setup Process 1 Assemble five FC tiles to be the center tiles of the whole display and level them out using a bubble level Turn the side lock with hexagon screw to connect two tiles horizontally Image 4 2 Five FC tiles are installed in the horizontal line Tiles horizontally connected with side lock p p p e ee a o DEMNMENCNETE E ee a Side lock engaged Image 4 3 Two tiles horizontally connected with side lock 23 FC series User Manual 2 Assemble the FC tiles at2. Monitor extend Interface 50 pins data interface Image 3 7 MRV300 receiver card 12 FC series User Manual 3 4 LED Control System This chapter introduces the control system and software of A24 display 3 4 1 MCTRL300 Controller MCTRL300 is LED controller with autonomous power supply The main functions are shown as below 1 DVI interface for video input USB interface for instruction communication Resolutions supported 1024 X 1200 1280 x 1024 1600 x 848 1920 X 712 2048 x 668 Two serial interfaces Light sensor interface integrated D o0 A CNO Audio input interface integrated rial t ar Serial outpu Serial input Status indicator Light sensor extender DVI input AC power input USB port RJ 45 port 1 amp port 2 Audio input Image 3 8 MCTRL300 controller 13 FC series User Manual 3 4 2 MSD300 Transmitter Card 1 DVI interface for video input 2 USB interface for instruction communication 3 Audio input interface 4 Resolutions supported 1024 1200 1280 1024 1600 848 1920 712 2048 640 A Caution A multifunction card is required for outputting the audio 5V DC input CR op O RJ 45 port 1 amp port 2 Audio input USB port DVI input Image 3 9 MSD300 transmitter card 3 4 3 MCTRL500 Controller 1 Two DVI interfaces for cascade video input and output 2 Audio input interface 3 Optional data output interfaces 4 RJ45 Ethernet ports or 4 optical fiber ports to
3. grounding circuit breaker with proper rated power Install the display in accordance with local electrical installation standards In Europe comply with EN 60364 the standard for electrical installation of buildings In Germany comply with EN 60364 In America comply with National Electrical Code ANSI NFPA 70 Protective grounding To prevent against the risk of electric shock the installation should be properly grounded Defeating the purpose of grounding will expose you to the risk of electric shock FC series User Manual 2 3 System Requirements Before you begin it is assumed that you are familiar with the Windows operating software The CD ROM in your package contains a Windows 7 based installation program You can install the software from the CD ROM System requirements Minimum specifications Hardware n PC Pentium IV 2 0 GHz or equivalent n 1GBRAM n Free hard disk space 10GB n XGA resolution 1024 x 768 n Serial communication port n Ethernet connection Software n Windows 7 Professional Recommended specifications Hardware n PC Intel i5 processor or above n 4GB RAM n Free hard disk space 500 GB n SXGA resolution 1280 x 1024 with 512MB video memory n Serial communication port n Ethernet connection Software n Windows 7 Professional FC series User Manual 3 SYSTEM INTRODUCTION 3 1 Brief Introduction FC series is the LED indoor display product of LIANTRONICS that uses die casting aluminu
4. M10 Bolt Connection plate Module Ground beam Image 4 10 Tile was connected with the connection plate by M10 bolt 28 FC Series User Manual 3 Put the modules back to the tile and connect the power cables and signal cables at the same time Supporting steel structure Tile Connection plate Ground beam Image 4 11 One tile installed on the frame 29 FC series User Manual 4 Continue to assemble the FC series display tiles from center to left and right sides from bottom to the top row after row and connect the tiles one by one AN Caution Before assembling the next tile make sure the whole display smooth and seamless Supporting steel structure Tile Ground beam Image 4 12 Side view of the whole led screen 30 FC series User Manual 4 4 Data Cabling Before distributing the data cable see the section 3 3 about FC Display Tile for detailed information of the data cord s socket and plug and their locations in FC display tile Warning Pay attention to the cabling direction in the following image The image below shows data cabling seen from the rear of FC display of 5 tiles wide and 8 tiles high The data link cable goes vertically and starts from the lower left corner seen from the rear The settings
5. Tile Tile FC Module l Data In y DC j Power In m lia lia FC Series LED Tile Image 3 1 Block diagram of FC Series LED display system FC series User Manual LED Display Components List Number Name Function Explanation LED Display Components FC series displaytile Tile size 576mm X 576mm Weight 11 kg 2 Power cord plug and Used for power supply loop between tiles the plug is for Socket output and the socket is for input 3 RJ45 data cord plug Used for data link between tiles the plug is for output and and socket the socket is for input Control System Components Bee ey ay Conto Industrial control computer computer Controller Convert and send video signal Distributor Distribute the data signal to different tiles ee grannies Support the output of multiple screens 5 Light sensor Adjust brightness automatically according to the environment brightness One card for one tile 7 io das RGN Support remote power supply 1 Control set and play video liston LED display 2 Support calibration on site 3 Support manual and automatic brightness adjustment 4 Support turning on off LED display through remote network LED control system software Power Distribution System Components Power distribution Support remote control power supp cabinet i P a Power distribution box Support remote control power supply Lightning arrester International brand to avoid lightning Comply with international stan
6. M cui ads C Operation humidity ii di pth ane Storage temperature 40 C 60 C Storage humidity 10 807 RH Life span hrs 250000 Normal Temp MTBF hrs 23000 Compliant Standard CE FCC RoHS FC series User Manual ile Dimensions T Appendix B 44 FC series User Manual Appendix C Package Flight case Dimension mm 829 L X 632 W X 677 H Volume m 0 35 approx Capacity 6 tiles of FC ur 45 e Ll ianIronics TREE 8 C RoHS F call centres 400 888 0156 website wwwich com stock coda SHENZHEN LIANTRONICS CO LTD Heodquanern ADO Lianhonics Bullding No 1 of ludan 3rd Rood Section 58 Bacon Dissriet Shenzhen City PRC Tel 86 755 29 7460688 Postcode 518101 Alter service 845 755 297456483 29744657 E MAIL overseotrhanironics com servicedidcih com
7. can be from PC DVD TV tuner etc Image 4 11 System connection diagram of a typical LED display 33 FC series User Manual 5 START UP OF THE SYSTEM 5 1 Software Installation Before you run the software please make sure all connection are ready From PC to sending card from sending card to LED screen Put the LED system installation CD into CD ROM Lil Erali Ta tup axe 1 Double click to start LED control software installation 2 Follow the installation instruction until the installation procedure has finished 5 2 System Operation First power on the control system computer and switch on the power of LED display follow the procedures and instructions as below 1 Start Nova LCT control software Install Nova LCT control software double click the icon image 5 1 to open Nova LCT Mars control software and the computer will enter to the interface as image 5 2 Local system info shows the real system connection information when it shows Control System 1 it means the USB serial port connection is ready for communication between PC and controller If not it shows Control System O for the connection is not good with no communication If there is no image on LED screen green indicator of sending card not flicking please check DVI cable from graphic card to sending card then check multi display mode from control computer Keep display mode under duplicate mode cy re NovaLCT Ma
8. electrical connection with 4 FC display modules There are special designs for fixing and connecting the tiles at each side of the die casting aluminum frame The frame has attachment points at the back and four corners The attachment points are to fix the tiles to the supports like steel structures and buildings Upper handle Left guide pin d Right guide pin LED module frame X4 Side lock Front face of LED modules populated with SMD LEDs Image 3 2 The front face of FC display tile FC Series User Manual 1 FC tile has 4 grids for 4 modules to be fixed in Each module is installed 10 magnet columns The module depend on the magnet adsorption on the frame The precise positioning of the location holes on the frame to ensures the precise positioning of all modules Keep frame clean to achieve smooth installation of the modules and avoid seams between tiles and uneven pixel pitches There are also materials for eliminating the seam between tiles to ensure the smooth and uniformity of the whole display 2 There is a pair of power data sockets and a pair of power data plugs at the back of each FC tile The sockets are for inputting power data and the plugs are for outputting of power data 3 Each FC display tile can be equipped with thermal speed controlled fans to make sure the normal working temperature of the tile under high temperature conditions 4 Each of the four corners at the back of FC die casting aluminum f
9. for the small system single phase power box can be used while for the medium system each of the custom power boxes solutions can be used Image 3 17 Single phase power box ELIT TE EL n Xm nds Image 3 18 Three phase power cabinet Note Consult the power box manual for more information about installation and usage guidelines Power Supply Location Install power distribution cabinet in the control room outside of the display structure Install a control box inside the display structure which can control the display power supply independently and control the maintenance of sockets and the lighting equipment If it is 3 phase power supply each phase should bear equally 19 FC series User Manual Power Distribution System The power distribution cabinet has air switch leakage protection switch fuses AC contactors power lightning arrester The door of the cabinet is also equipped with current voltage testing meters knob switches and signal lights The distribution cabinet has protection of lightning overvoltage overcurrent undervoltage short circuit open circuit and leakage The main switches in the power distribution cabinet are made of the Schneider devices and all other accessories and wires has CCC certification 3 Phase 5 Wire Power Line Description EE 1 AC380 100A AC input 2 AC220 63A 25A 16A multi output 3 In addition to the display power supply there also is power supply f
10. in the control software refer to the display seen from the front So the first tile in the data path indicates the lower right tile of the display Control PC LED Display Controller Image 4 9 Example of data cabling 31 FC series User Manual 4 5 Power Cabling Before distributing the power cable see the section 3 3 about FC Display Tile for detailed information of the power cord s socket and plug and their locations in FC display tile A Warning Pay attention to the direction of the alignment in the following image rms m nha Ena ie EB iini P LI A rear view picture of data cabling and power cabling Spider Connector with Fuse Spider Connector with Fuse Power Distributer Box To AC Power Image 4 10 Example of power cabling 32 4 6 System Connection FC series User Manual A display is constructed by tiling LED tiles This diagram shows an array of m row by n column of LED tiles Dashed blue lines show data signal wiring UTP cat5e cable carries video signal Y from transmitter card to display tiles as b shown in this diagram The coverage Cat 5 Cable 1 distance of the first jump from LED l controller to the first tile is 100 meters 4 DVI D Cable Control PC LED Controller DVI cable feeds video signal into LED controller Acceptable signal for LED controller is DVI D Largest video size is 1280 1024 SXGA Video source
11. scan boards receiver cards 4 RS232 serial ports for cascading instruction communication 5 Maximum load capacity 1920 X 1200 Image 3 10 MCTRL500 controller 14 FC series User Manual 3 4 4 MFN300 Multifunctional Card 1 RJ45 ports for connection with receiver cards serial ports for connection with the control computer Support 8 power supply control Support light sensors Support temperature and humidity monitoring gt OF xe m9 Dg Audio input interface Caution For audio output the multifunctional card needs to be connected between receiver cards or at the end of the cascading chain Relay contact Serial port TS Audio output m E La Sve rani RJ45 port Sensor extend port HIHHIBEHTEHS ee OOM a DN Relay contact Image 3 11 MFN300 multifunctional card 3 4 5 NS048C Light Sensor 1 For environment brightness monitoring 2 Connect to receiver cards MSD300 MCTRL300 or multifunctional cards MFN300 3 The cable of standard configuration is 5 meters With a special ordered cable the working distance can be extended up to 100 meters Image 3 12 NS048C light sensor Note Consult the controller manual for more information about installation and usage guidelines 15 FC series User Manual Do WAMF EK 8 al 3 5 LED System Control Software NovaLCT Mars control software is used to configure and control LED display through PC in G
12. the center in the second row The upper and lower tiles are vertically connected with matching mechanism as shown in image 4 12 and level them out using bubble level These two tiles are locked when you push the matching mechanism up and then rotate it to middle These two tiles are unlocked when you push the matching mechanism up and then rotate it to both sides Image4 4 Assemble the FC tile in the center of the second line 3 Continue to assemble the other FC tiles at the second row from center to double sides The corners of every two tiles at the bottom are fixed with special connecting plates Fix the connecting plates to the supporting steel structure at the back of the display See the steel structure design and installation image for more details li H Jan E ee aah oo Ear a JM O Ta TES a SPS n Pun i The installation base level Image 4 5 Tiles vertically connected with matching mechanism 24 FC series User Manual 4 Fix the corners of four adjacent tiles with connecting plates and corresponding screws and make appropriate adjustments if necessary to ensure the smooth and seamless surface of the FC display Image 4 6 Fix the corners of four adjacent tiles with linking plates 5 Continue to assemble the FC display tiles from down to up row after row Connect the tiles one by one A Caution Before assembling the next tile m
13. to excessive force of impacts All warranty claims regarding damaged modules due to incorrect packing will be rendered invalid N FC series User Manual 2 INSTALLATION REQUIREMENTS This chapter specifies the requirements for safety mechanism electricity and control software of FC Series LED display Warning This LED indoor product is designed only for indoor use Never install and use it in outdoor environment and keep it far away from direct sunlight dust and moisture 2 1 Mechanical Requirements Weight Warning Do not underestimate the weight of a complete FC Series LED display Be sure that the floor on which the FC display has to be installed is capable of handling five 5 times the complete load of the display For floor mounting conclude the weight of any other load Caution One FC tile weighs approximately 11kg Horizontal surface For floor installation the floor on which FC display is installed must be horizontal Never install LED display on a slant surface Ballast Depending on the height of the display and the position of the LED display upon the foot beams somewhere between front and middle additional weight ballast will be required Consult professionals of LIANTRONICS to calculate the minimum ballast you require for safe installation of the LED display Installation ambience e Environmental conditions humidity ventilation temperature etc Location Altitude etc e Front clearances
14. Cunent Cirpiaw Made Se ell le Tb et D34 Ro lp 12803 10724 Bee Senne Goad doh moe Fie sa katiore 1280 x Od pa f 1 cuatam Fiplre rin Rate amp en a Hr Hoj Backup Seing Haster Device Slave Dewi ce id crater Bandi Baaniinigs Mister Por indes Bene Pood Indes B Image 5 5 Sending board configuration interface 4 Go to scan board configuration Asis shown in image 5 6 select Load File down load rcfg file from delivered CD Click Send To HW and then the file will be send to each scan board receiving card Click Save and save all files in hardware when restart power files is no need to send again If tiles shows correct images before loading file skip this step and directly jump to step 5 Sending Douai Acin Eca O m eee hus ire Ca oe on a ar C Eme TETE La Credins Horton Osc cida Tara ec MF CIRO EE DH ng lanl Ew Pari necs E iij am ara dobre Retest Asja F necukraDe 3 Gras Sea Gr Mpde Cha ha Clark Cuts Cary nek Pe l Love Gray Cp Fisrkin Tire r B idie Birini LingcrameT Pies Em Prigtines FE Image 5 6 Scan board configuration interface 36 FC series User Manual 5 Screen connection According to the data cabling of your LED Display fill in the actual value of columns and rows Choose right ports and fill right scan board size as below Select correct direction of signal cable cascading Image 5 7 shows the front view of screen S for the first tile
15. E iin AK E pesa a dinda da sao aid Mol 1 2 Installation Requirements sees uiae cM sa 3 2 1 Mechanical Requiremenis erre ene eene ne nenne 3 2 2 Electrical Requirements esee rennen oai eee 4 2 3 FWSM Requirements eese eene eene nnne cerco iie cif ui Eee eere eee enne ins 5 3 System Introduction 1 eee ALL once anos vs tao ciaaas dai 6 SU Brief Introduction iiuieeieeeeeseeeeeee eene DR enne rann 6 3 2 System Componenis c co Ul OS EDI LLorem 6 3 3 LED Display Components ER TE ERA 60 oe ccc cec eee eceeceseecenceseeceeeessees 9 3 4 LED Control System c Rc eeresesesemsesa 13 3 5 LED System Control Software EB ABE essere 16 3 6 Peripheral Device VERD 17 3 7 Power Distribution System MR eere 19 4 SIUP EOC CSS sabio siri angana diria dada dia Sr a dada MEE 21 4 1 installation FCO Al ANON as crie a RES AS Did vua Min id assado 21 4 2 Setup Process of rear Standing Installation i seis 23 4 3 Setup Process of Front Standing Installation c eee eee ee enna 27 wA eA MN n 31 AS Power Gabling cscscccsecsicveienasnaded edaca weed osucwotstaadeddedaandahaiseabes dcaweeeadeeedsaahedseadeeaddezoes 32 AG System CONMECHON TTE o 0D 33 5 Start up OF tlie SySIelti s
16. ake sure the whole display smooth and seamless The installation base level Image 4 7 Increase the tiles from down to up 25 FC series User Manual 6 Fix all the corners of the FC tiles at the bottom and flanks with connecting plates Fix the connecting plates to the supporting steel structure at the back of the display See the steel structure design and installation image for more details Tile IF ini PP mS ELE PX aum i IM Fa Pa Supporting stee structure LA d 1 1 i mc PP a a Y Image 4 8 Example of stacked installation 6 X 6 tiles 26 FC Series User Manual 4 3 Setup Process of Front Standing Installation Warning The height of FC tiles depends on the height of supporting steel structure and the display surface has to obtain the flatness within a tolerance zone of 0 2mm and keep perpendicular to the reference surfaced Setup Process 1 Fixthe connection plates to the frame There are two ways either weld or fixed by SCrews Supporting steel structure Connection plate H Ground beam H Image 4 9 Connection plate was fixed on the frame Er FC series User Manual Do Ta m 3 TT MF 2 Remove all the modules from the tile and then use the M10 bolt to fix the tile to the connection plate Tile Supporting steel structure
17. and E for the last one Choose Send to HW and Save Siman Tipe C imole Birnen Etandard Sereen O Cime Boreon Basi Hmioerrestion Ba Loeaip x 1 y i rua We C Ershie Operam Po Ex an Board j Eten Baan el e Columns B ITE Hide Line Sanda Board indes Scan Bond Siu Hewitt nO HotetClick mr drag left mouse button to config rzresn right muss button to cance es gt us Image 5 7 Screen connection interface 37 7 FC series User Manual 6 TROUBLE SHOOTING 6 1 Software Trouble Unable to open NovaLCT Replace LCT software Software problem X 1 Computer is not installed with NET Framework 2 Already installed but Computer is not System notice Install Microsoft installed with NovaLCT exe error NET Framework 2 0 NET Framework software may be damaged The RS 232 communication is not connected or not get through Let munication Nova LCT version may be Replace LCT changed confirm that you is not stable use the right version Set values of R G B brightness on the all the same brightness values are controllers as the 2 Data is not saved not the same same successfully after setting Check the RS 232 connection and communication LCT system connection fails Controller s R G B 1 Brightness values not 1 Calibration mode is not On 2 Allthe calibration modes are On but not successfully saved after setting 1 Bright
18. but problem still exists replace the receiver card Check RUN status on There is no data the divider If it blinks 2 fromthe controller seconds once it means or the fiber cable no data from the fiber IS not well cable connected Divider driving area is black Hardware problem Receiver card problem causes black display on single tile Poor Cat5 connection or output data problem of the upper receiver card If there is no data input from the cat5 check the cat5 connection or no data output from the upper receiver card Check the hub card connection with the scan card or the ribbon Receiver card One row of the module in the tile is black or messed up cable connection between the hub card and module If Connection problem or hardware problem connection is no problem replace the hub card FC series User Manual 6 3 Module Problems LED lamp Blind lamps me amp ecean or sogenng Replace the module is not good LED pixel The pixel is black or loses color LED module The driving IC resistor is bad soldered or out of work One or several whole LED Cable is not connected or not modules in the same row well connected are black or defective 6 4 Power Problems Problem type Power supply Power supply Problem description Reason The whole tile is black the breaker is turned off The power supply feeding the The whole tile is black receiver card is defective Several nearby
19. dards Peripheral Devices Different models of Voao or Magnimage are available Onal fier Both single mode and multiple modes optical fiber pe transmitter can be used multiple modes transmitter for transmitter 500M and single mode transmitter for 20KM Optical fiber 8 cores optical fiber with premium brand 4 E E R Axial flow fan can be chosen according to the heat dissipation space and the environment temperature Warning LED display modules can be easily damaged so the original packing materials are needed for the maintenance of the display modules All the warranty claims are invalid for the damage caused by wrong package FC series User Manual 3 3 LED Display Components FC Tile FC series LED display is built with FC tiles A tile consists of die casting aluminum frames in high accuracy FC display modules switching power supply receiver cards and some other mechanical and electrical connection paris The FC die casting aluminum frame adopts one time die casting and CNC precision processing technology with high quality aluminum to ensure the high accuracy of the frame and the uniformity of the whole display The introduction of the main components of FC tile is shown as below with related images 3 3 1 Die Casting Aluminum Frame Each die casting aluminum frame is installed with four FC display modules There are LED signal receiver cards and low voltage DC switching power supply inside the frame and they all have
20. ention to electric shock Warning Wear a hard hat to reduce the risk of personal injury Warning Be aware of suspended loads A Warning Mind your fingers while dealing with heavy loads Personnel of installation and maintenance The installation and maintenance of this product must be performed by authorized and qualified technical personnel only The manufacture dose not take responsibility for the results caused by incorrect improper irresponsible and unsafe actions GND and Lightning protection Do not underestimate the safety protection of grounding plug socket If the supplied plug socket is defective replace the defective parts Ground the product correctly to avoid electric shock caused by large electricity leakage Disconnect the power in the time of lightning or provide other suitable lightning protection device Disconnect the power plug when the product is not used in a long period Ambience of installation and use The ambient temperature for LED display max 60 C min 40 C e Ensure that the ventilation is good Do not jam or drop metal particles and cable pieces into ventilation opening Keep the ventilation surface clear without foreign matters like wrapping materials False actions may lead to poor ventilation and cause fire malfunction and error Install LED display far away from radiator heater furnace and other equipments hindering ventilation and heat dissipation including but not limited to ampli
21. fier laser ultrasonic vibration devices flammable materials like curtains and other unsafe devices e Osignal cables should be shielded to restrain the high frequency interference LED display can not contact with any corrosive and abrasive matter Do not use LED display in moist ambience in ambience containing airborne contaminant dust oily fume corrosive gas and flammable gas and in ambience with vibration and shock This LED indoor product is designed only for indoor use Never install and use it in outdoor environment and keep it far away from direct sunlight dust and moisture FC series User Manual ESD and LED LED components are ESD Electro static Discharge sensitive Do not touch LED components when the display is in operation or switched off Disconnect device When the appliance inlets of the individual tiles are not accessible the socket outlets supplying the rack shall be installed near the equipment and be easily accessible or a readily accessible general disconnect device shall be incorporated in the fixed wiring Mounting parts The mounting parts are only used to install LED display Do not repair or copy Only use parts appointed by the manufacturer Contact LLANTRONICS if you want customized application Product care Inspect all installations on a routine basis to check security wear deformation corrosion or any other situation that reduces load carrying capability Increase inspection fre
22. for optimal effect ensure that enough free space is supplied in front of the LED display and respect the minimum viewing distance Comply with local regulations regarding such installations FC series User Manual 2 2 Electrical Requirements Power requirements The displaying area of one FC tile is 0 332 m FC Series LED tiles have different pixel densities see Appendix A technical specifications For different pixel densities one FC tile may need power supply of 0 6 amps to1 5 amps at 220 VAC 100 250 VAC 50 60 Hz Each FC tile has one input and one output socket of AC power The power is distributed to display tiles by power split cables from power distributor However one power split cable can be connected with 8 20 tiles in parallel So one power split cable has to be provided for every 8 20 tiles Protect every power cable by a circuit breaker or fuses rated 16 A 250 VAC 15 A 110 VAC in the USA and Canada LIANTRONICS provides a range of power distributor to satisfy the demands of your LED display See more details for power distributor of LED display in Power Distribution Section Contact LIANTRONICS for more information Power system It is recommended to use power distribution system with a separate neutral and grounding conductor to avoid large current loops due to voltage differences in the neutral conductor e Protect the electrical installation by switch circuit breaker over voltage protector defective
23. ge 3 14 LC LC fiber cable Status indicators RX Port TX Port Power switch AC Input Image 3 15 CVT 310 transmitter receiver and optical fiber Note Consult control system manual for more information about installation and usage guidelines 17 FC series User Manual 18 Video Processor on Oo o0 O E BH 8 BB868B J qop o it A Image 3 13 Video processor front view e gt MomukeyFunctions gt Numerical t select AV SROP Numeicalaseect AVA PART Numerical AVE T NumercaldscectAVA AUTO Numerical5 fading transition VODE Numerca iselect VGA MENU Numerical seiva LEFT NumericalBlseect DV r Numercalagelect HOM vou El lil x H ia EAT Aad ag ope m m m 2 t g he r e D LA Ti vut p Ui Tai ri sn E D a a Hl E w G i 5 1 1 B d r 3 mu pn 2 Image 3 14 Video processor rear side Video Inputs Video Outputs AV1 AV4 4 video inputs DVI1 DVI2 2 D SMIDUS DVI D single link wed a 1DVI input DVI D single link DVI Loop l Tx Board1 HDMI 1 HDMI input TEL E M Extension module 4 FC series User Manual 3 7 Power Distribution System Power Distribution Tile The use of proper AC distribution system is necessary to make sure the safe operation to FC Series LED display Although the third party solution is available LIANTRONICS offers power distribution solutions with various sizes and types As
24. m frame with CNC high precision machining techniques With its compact light and handy exterior the LED tile is easy to install and disassemble As the tile dimension is of very high precision so the whole display keeps in high flatness and seamless 3 1 1 Key Benefits e Support for both front and rear maintenance e Uniform color and high contrast ensuring clear and sharp picture e High precision die casting aluminum tile achieving high flatness and seamless matching of the whole display e Fan less design with good heat dissipation achieving noise free e Light and slim tile easier to handle and transport e High stability and reliability prolonging lifespan of the display 3 1 2 Applications Indoor hall multi functional conference hall performing hall theater stage command and control center and so on 3 2 System Components FC series LED display system includes the following basic components e LED Display FC series LED display tiles power supply cables signal cables connectors e Control System control computer LED display controller distributor control system software e Power Distribution System power distribution box power cables e Peripheral Devices video processor optical fiber transmitter FC series User Manual FC FC FC FC LED LED LED LED Tile Tile Tile Tile FC FC FC FC LED LED LED LED Tile Tile Tile Tile Control FC FC FC FC LED LED LED LED Tile Tile Tile Tile FC FC ets LED LED LED
25. module areas are black The power supply feeding the module area is defective 6 5 Data Transfer Problems The fiber cable is broken or The display is black the data I O order is wrong The whole column of the The connection is not good or the cat5 is defective display is black One or several tiles in column are black The connection is not good or the cat5 is defective All the display lights up but the columns are not in The connection order is wrong right order Power to the tile is not good or Replace the module Check the ribbon cable and power cable connection on the module Check power connection with the tile and the breaker in the tile Replace the defective power supply Replace the defective power supply Check the fiber connection and the data I O order Check the data connection between the divider and the first scan card Check the catb connection between the tiles Check and correct the Cat5 connection order in the divider FC series User Manual 7 MAINTENANCE Routine maintenance 1 2 Make sure the LED display is well ventilated dry and running in suitable temperature Regularly check the internal cables inside the LED display are in stable connection the power supplies are working well the ground wires are connected well and the lightning arrester is running well Regularly wipe the dust on the surface of the LED tile with a soft cloth and keep the LED dis
26. ness adjusting modes are not set as the same 2 The setting is not saved successfully The calibration mode The brightness is of controllersdid not different before and set to On after calibration Nova LCT display brighiness is not uniform Brightness adjusting Change the brightness modes are different adjusting mode between different controllers Check Gamma value of different controllers and resend the database Gammavalues are different for different controllers If brightness adjusting is in auto modes and Brightness sensor controlled by sensor action need to wait new update need to for 30 seconds wait for 30 seconds shows wrong status LCT software card is black column setting in LCT LCT is wrong The whole displayis schedule setting is wrong black Media source is lost source or stopped FC series User Manual 6 2 System Hardware Trouble ron vo sca AS Controller Black screen MEE from the graphics card Divider is working Divider No DVI signal to the controller in PC when RUN lamp blinks heck the power of the No power for the controller controller 2 times per second Re start the controller AR The lamp blinking 2 seconds per time means no data is output from controller or the fiber is broken Check the power of the No power for the divider divider Check data input from upper receiver card RUN lamp blinks 2 times per second If the data in is ok
27. nual Furthermore make sure that all the installation requirements are fulfilled The truss beam and level system used in this chapter are pure instructive and assumes the truss beam and level system have been installed and answers to the flatness requirements The customer is free to install his own truss beam and level system according to his own wishes but answering to the mechanical requirements mentioned in this installation manual 4 1 Installation Preparation Package Check Product Item Number Confirmed e Package Perfect e Complete Screen Appearance No Scrape Cabinet Off line Test FC cabinet supports off line test Users can test each FC cabinet without connecting with LED control system The test steps are as below 1 Make sure that the receiving cards are connected with each of the LED modules but not connected with CAT5 data cable 2 Turn on the LED screen the tiles show nothing 3 Press the black switch on the receiver card seven times Then the display contents on the LED tile will be changed to Diagonal Grey Red Green Blue White and Black in order Press this button to change test pattern Image 4 1 Off line Test button on receiver card 21 FC series User Manual Installation Preparation Good viewing angle and good sight for the surroundings Favorable ventilation conditions Safe and stable rating input voltage Suitable size firm and stable installation table board
28. or EZD100EGP maintenance and lighting 4 PLC control lightning over current LE UA under voltage leakage protection OOD urs 5 Automatic power off by the fuse BH 0 66 manual or PC automatic operation 100 5 and extemal power supply in emergencies FUTIS 3 Image 3 19 Typical power supply system diagram Selecting and layout of the power line e LED display is supplied with AC220V power with good grounding and requires that the grid voltage fluctuation is less than 10 Determine the diameter of the power cord according to the power of the display Unit mm the cross sectional area of the power cord e Power lines set aside 5 10m between the power distribution box and the display Cable set aside 5 10m between the control room and the display The power supply has three wire system live neutral and earth or five wire system 3 live wires neutral and earth When the maximum power consumption of the LED large display is less than 10 KW generally use single phase three wire power supply and vice versa use the three phase five wire power supply 20 FC series User Manual 4 SETUP PROCESS This chapter describes the process of suspended installation and standing installation of FC Series LED display Warning Safety first Fence off the installation area before starting to install Ensure you A read understand and follow the safety instructions mentioned in the chapter Safety of this installation ma
29. play surface clean to avoid brightness differences between clean and unclean LED tiles Cautions for use 1 Before power on the LED display start your computer first and then turn on the power of LED display Before turn off the display system first turn off the power of LED display and then turn off the computer When you are editing video playlist you had better to keep the LED display closed When failure appears first turn off the power of LED display then contact with service department of LIANTRONICS for technical support Change modules 1 Insert the special tool into the gape between two modules 2 Then pull the tool out The module will be pulled out at the same times 41 FC series User Manual 42 FC series User Manual Appendix A Technical Specification Pixel Pixel configuration ARIGIB IRIGIB IRIGIB 1RIGIB 2 000 white Brightness nit 1 200 1 600 1 500 1 500 black Contrast 1 000 1 white 2 000 1 black angle H 140 V 140 Pixel density pixel m 111 111 62 500 49 382 27 777 Module mm 288x288 Module resolution pixel 96x96 72x72 64x64 48x48 Tile size mm 576x576 Tile resolution pixel 192 x192 144x144 128x128 96x96 Tile type and material Die casting aluminum cabinet Average power 250 consumption W m Max power consumption W m Refresh rate Hz 1920 750 Frame rate Hz SCS Operation storage Operation
30. quency for key parts Keep structural and mounting parts dry clean lubricated only if recommended coated properly and maintain complying with part design Defective parts must be removed or replaced at once Installation and wiring Install the display and connect cables following the manual instructions The installation and wiring must be secure Poor connection may lead to malfunction Do not step on power data cable or squeeze plug socket and power data cable Do not suspend any items on cables or the back of LED display Connect or disconnect the cables of data communication extension module or control unit after the power is off to prevent product damage or malfunction Risk of electric shock e To avoid electric shock and damage do not dismantle the inside electrical parts e Do not hot plugging the cables to prevent electric shock or circuit damage e Keep clean after installing and cabling Be ensure all the devices and terminals are covered before tune on the power e Do not touch the terminals when power is on Clean and screw the terminals when power is off Moving or transporting product Do not hit the corners of LED tiles when installing or dismantling LED tiles Be careful when moving or transporting the product to prevent any damage LED tiles can not be transported in containers other than LIANTRONICS flight cases or packaging Even the use of LIANTRONICS packaging does not guarantee the LED tiles against damage due
31. r E Image 5 1 E eI Dhiiisg Plug in Tem Et LI Lacigiu age m nguLi aLi LEM X E Urges ma do Lug pal d nan per H peine l ETIA ias Lima eee hh E Laktrsl Eya yim Momo emo Mo Screen click here to comig Dep Ga Hepa A J 01 Image 5 2 34 FC series User Manual 2 User Login User login This menu is for user to login It is necessary for the configuration of the LED screen Click User Advanced Log in enter password 666 or admin HovaLCI Kars 73 2 2 System Toolsil Plug in ToolfPi ser LanguagefLangifiLi HelprH Bx s Brightness Display Control Monitor Function Card Local System Info EE User Login Control System View Detail Monitor Info Server Status Server ersion 2 0 Image 5 3 Login interface Select Config Screen directly to follow the next step O ree LIST Vi 2 2 System Tools E Screen Config Select Serial Part i voren Config Corrent Serial Fart yz tem In D Control System Config Sereen Y Load Config File Monitor Info Pn ues Server Status Sarver Veraren l U Image 5 4 Configuration interface 3 Go to sending board configuration As is Shown in image 5 5 select proper resolution for sending card and it should be close to graphic card Click Save to save parameter on HW 35 FC series User Manual Sanding Board Sean Beard Screen Comacin Cal el ere Belg
32. ra m 1A tt pa k f ir L nm In a E kg a 1 UM A eer g E 255 ado eo p n ER IT ar tra IL LE R a eet d This manual is only for operating instructions and does not serve as repairing service Changes Liantronics provides this manual as is without warranty of any kind either expressed or implied including but not limited to the implied warranties or merchantability and fitness for a particular purpose Liantronics may make improvements and or changes to the product s and or the program s described in this publication at any time without notice This publication could contain technical inaccuracies or typographical errors Changes are periodically made to the information in this publication these changes are incorporated in new editions of this publication Copyright All rights reserved The copyright of this manual is protected by the Copyright Law of the People s Republic of China and other intellectual property laws No part of this document may be copied reproduced distributed translated or used for commercial purposes It shall not otherwise be recorded transmitted or stored in a retrieval system without the prior written consent of Liantronics LIANTRONICS CO LTD Add Liantronics Building No 1 Liuxian 3rd Road Section 68 Baoan District Shenzhen China Postcode 518101 Visit us at the web www liantronics com FC series User Manual Contents P
33. rame has a fixed screw hole to support the installation Each side of the upper frame has a pin used for the precise connection between the upper and lower tiles Warning A maximum of 15 tiles are limited to stack up without the external support Upper handle Left guide pin Right guide pin i hy Side handle f Back door lock cce inh II en 1 Allen key operate rr side lock AC power connector Data link connector AC input socket Status indicator Data input socket Side handle ao Fixing screw hole for installation WI 1 Image 3 3 The back face of FC display tile 10 FC Series User Manual 3 3 2 FC Module FC module includes plastic base frame PCBA plastic mask etc At the back of the plastic base frame two copper screw holes are inlaid at each side to fix the module to the die casting aluminum frame The black LED lamp array lies in front of PCBA Over the lamps replaceable masks are equipped to protect the LED lamps and PCB and increase the light efficiency of the display LIANTRONICS adopts the black full color SMD LED lamps The use of black organic silicone and diffuser makes the black LED lamps darker to improve the contrast of the display significantly FC tile includes 2X2 FC display modules Each module has five kinds of pixel pitch mm PH 3 mm PH 4 mm PH 4 5mm PH 6 mm with the corresponding module resolution pixel of 96 X 96 72 X 72 64 X64 48X 48 The
34. raphics User Interface PATENTE ef oats ie Currum n mi EET Lx n Er ga Ekki Fani OT ER E allele Lati cun H px pes gr IHCCHE CHE ILI D ee CEN O eee ee EE nm i ree E ae rium ES A Eur inar Po F EFIE iE m we a ir Chih P Ee i LER E ete mj rg E miki Mmi Cente miral jj E Hm ferrar Ge 55S Plug in ToolfP LUserd LanguagefLangifLi HelpiH au X as Screen Config Brightness Calibration Display Control Manitar Function Card Local System Info Control System Other Device Monitor Info No Screen click here to config Server Status Serer Version z D Image 3 13 NovaLCT Mars control software interface Note For more information about installation and instruction of control software consult Nova LED Display Control System Mars 3 User Manual 16 FC series User Manual 3 6 Peripheral Device M3 CVT310 CVT320 EO converter When the distance between LED display and the controller is beyond 5 meters optical converter is needed to ensure the complete signal and reliable system LIANTRONICS offers two complete solutions of optical fiber transmission including transmitter receiver and optical fiber Your choice depends on the required cable length Main Features Use optical fiber of multimode double cores and LC interface Transmission distance up to 300m e One RJ45 Ethernet port for data input e Power supply 100 240V AC e Usein pair m Ky Ima
35. s das nas isa neo doa anos sadias sacada has 34 5 1 Software installation ee serrana EE EE mme enne nens 34 5 2 OVO PERA ee Srs o ASI ere ee Saio eee 34 6 Trouble Shooting AE wise soe boia asian ssa ds sp seta xecetcecnctets 38 6 1 Software B00 0 gt serena eme enne esse sse ssh ns 38 6 2 Hardware Trouble 99 MiB cccccccce ccc eceesceeseesceeseessenceecueeseeceeceescescesscrsseeseeanes 39 6 3 Mod le Problems a BR io oo irre o RSS ada dad E xa SS a a pe gd 40 6 4 Power Problems Mk cesar nnn ne anra se seas ene gill 40 6 5 Data Transfer Problems sssssssssssssssssssssssss e ene e nme ensem nsns 40 7T Maintenanp b 9Ws LLeeeeuee eee eere eere ern enne nnn roa co 41 Appendix A Technical Specification ueesu 43 Appendix B Tile Dimensions eese eee ee eee 44 AppendbgC Package Lecce eee coco Meena eens 45 FC series User Manual 1 SAFETY This chapter contains important information to prevent personal injury and product damage when you install the display Read this chapter and keep it properly Ensure that you understand and follow all the safety instructions and warnings in this chapter before installing Personal Protection Warning Ensure that you understand and follow all the safety instructions warnings mentioned in this manual Warning Pay att
36. weight of each display module is about 1kg IN Warning FC die casting aluminum frame can only install FC display modules Replaceable masks High bright LED Magnet Signal input socke 5V input port Plastic base frame Back side of the LED module Front side of the LED module Image 3 4 The components of FC display module 11 FC series User Manual 3 3 3 Socket and Plug for Power and Data Connection The following two types of socket and plug are respectively used for the power and data connection between FC display tiles The power socket and plug is for the loop power connection between upper and lower tiles and the data socket and plug is for the loop data connection between tiles Image 3 5 Power and data plug and socket Image 3 6 Power and data plug and socket 3 3 4 LED Receiver Card Each FC tile has one receiver card for receiving and transmitting the data of LED display The functions of the MRV300 receiver card are shown as below e Power supply 3 3 5 0V Temperature monitoring standard feature Power supply voltage monitoring standard feature Working status monitoring standard feature 16 RGB data groups output it can be extended to 32 groups e Load capacity of single receiver card up to 256 X 208 Support pixel level brightness color calibration DC input c n E 22x 50 pins data interface d RJ45 port 1 je RJ45 port 2 N Extend interface uomo
Download Pdf Manuals
Related Search