User Manual - actlaser.com.tw
Contents
1. Channel 1 Single Color Channel 1 Tricolor Channel 2 Lines Selection Range Colors and Lines Selection Laser up down movement selection Lines change every 5 Colors and Lines change 226 255 226 255 228 255 Sound Active seconds every 5 seconds Lines change every 3 Colors and Lines change 208 225 208 225 seconds every 3 seconds 224 227 Laser lights continuously fast move downward Red Yellow Green 196 207 dotted line2 220 223 Laser lights continuously moderate move downward 157 207 Dotted line 3 183 195 Red Green dotted line2 170 182 Green dotted line2 Red dotted line2 216 219 Laser lights continuously slow move downward 144 156 Red Yellow Green line 131 143 Red Yellow line 105 156 Dotted line 2 213 215 118 130 Green Yellow line 105 117 Red Green line 92 104 Red Yellow Green 209 212 Laser lights continuously slow move upward dotted line Red Green dotted line i 205 208 Laser lights continuously moderate move upward Yellow dotted line 53 65 Green dotted line 40 52 Red dotted line 201 204 Laser lights continuously fast move upward Yellow line ff O 157 169 Dotted line 1 79 91 66 78 Trouble Shooting a If there is no light from the unit please check the main power supply and fuse a If unit does not respond to DMX please check the DMX cables are connected properly and are wired correctly E If unit does not response to the music please check the sound activation adjust2. Introduction Thank you for purchasing Mini Club Mini Club is a two channel DMX laser can be controlled via a standard DMX controller It is a lightweight mini intelligent fixture and is an ideal product for discos clubs exhibitions and any place that need visionary effect Mini Club provides red or green single color or red green yellow tricolor laser effect and three operating modes For safe operation read this manual before powering or installing the fixture follow the safety precautions listed below and observe all warnings printed in this manual and on the fixture Safety Precautions E Do not spill liquids into or onto your unit If this ever happens disconnect the main power immediately Do not connect this unit to any dimmer pack E Always disconnect from main power before making any type of connection E Be sure to locate this unit in a place with adequate ventilation at least 15 cm from a wall and mount this unit in safe and stable matter E To prevent fire or shock hazard do not expose this unit to a high temperature or high humidity area Please unplug unit when not in use E Always keep combustible materials away from the fixture E This unit is intended for indoor use Use of this unit outdoors voids all warranties m Always refer service to a qualified technician Never look directly into laser beam E Occasional breaks are necessary to prevent breakdowns E Caution Use of controls or adjustments or performa
3. ment a If problems cannot be solved please contact your dealer for service a You can adjust the position of green and red light by follow steps to make the best yellow light effect FOR AL28 TRI COLOR UNITS ONLY Step1 Set the DIP switch 12 to ON others to OFF Step2 Open the case Before you open the case please project light on to the wall Never look into the beam directly Knob1 Control green light vertically Knob2 Control green light horizontally Step3 control knob1 to vertically adjust green light line to the same position of height with red light line hace e Do R m G Step4 control knob2 to overlap the green light line and red light line tt Re gt G Lu Operating Modes 1 Stand Alone Operation Auto Sound Active Mode Auto mode a The unit runs built in program to change the laser effects automatically Set DIP switch pin 10 to ON other pins to OFF to run Auto mode Sound Active mode E This unit has built in program that will react to sound and music under Sound Active mode Set all DIP switch pins to OFF to run Sound Active mode 2 Master Slave Operation Auto Sound Active Mode This mode allows user to link up to 32 units to run the Master Slave operation In the Master Slave operation one unit will act as the controlling unit and the others will react to the controlling unit Daisy chain your units via the standard XLR microphone cables in the following configuration Out from the fi
4. nce of procedures other than as specified herein may result in hazardous radiation exposure Set Up Unpacking Mini Club comes with 1 hanging bracket 2 clamp levers 2 washers 1 adapter and 1 user manual Unpack carefully and be sure that no damage has occurred during shipping If there is anything missing or appear to be damaged please contact your dealer Power Connection Be sure the source voltage in your area matches the required voltage for your Mini Club before plugging your unit in Incorrect voltage selection will detrimentally affect the operation of this product DMX Cable Connection Mini Club is a two channel DMX fixture that can be operated with universal DMX controller This unit and DMX controller require a standard 3 pin XLR connector for data input and data output Installation Mounting Mini Club should be properly mounted by using a suitable hanging clamp and safety cable Use in a well ventilated area Be sure no ventilation slots are blocked Safety Label Position Rear Panel Front Panel Certification identification and warning label Warning label Laser aperture label Laser aperture Control Panel Introduction D Adapter Connection Sensitivity Adjustment Knob Power Switch DMX In amp Out DIP Switch Pin DM sporess PUN ie enaBhaud LEE EETTEESTI DEE Operating Modes Cont Operating Modes Cont DMX Signal Levels DMX Signal Levels Cont
5. ow Net Weight 2 5Kgs With an UL Adapter Input 100V 120V 60Hz amp Output DC 12V 1 2A or a CE Adapter Input 220V 240V 50Hz amp Output DC 12V 1 2A Classification 4 9mW to 20mW 3R 30mW to 200mW 3B L120 x W130 x H200 Material Metal Op Temperature 18 25 Your Best Mate 2007 ACTOR MATE CO LTD in Laser Lighting No 15 Lane 83 Lungshou Street Taoyuan City Taiwan 330 R O C Tel 886 3 3791326 Fax 886 3 3791919 www actlaser com tw active actlaser com tw ACTOR MATE
6. rst unit to In on the second Out from the second to In on the third and so on Auto mode E To set the master Set DIP switch pin 10 and 11 to ON other pins to OFF a To set the slaves Set pin 1 to ON other pins to OFF Sound Active mode a To set the master Set DIP switch pin 11 to ON other pins to OFF a To set the slaves Set pin 1 to ON other pins to OFF 3 DMX Operation E DMX operation gives the users freedom to create their own programs tailored to their own individual needs To run this unit in DMX mode connect the unit to any standard DMX controller via XLR connectors a Please consult DMX controller manual to determine address Function Selection Chart pi 2 3 4 5 6 7 8 9 10 11 12 SETSOUND AUTOMODE _ SET SOUND AUTO MODE MASTER ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF SLAVE SET ADDRESS OFF OFF OFF DMX MODE Cleaning a 7 Use a soft cloth and normal glass cleaner to clean the outside casing Cleaning Wy f n f gt i U D frequency depends on the environment in which the fixture operates Be sure to dry all parts before plugging the unit back in AL28 Series User Manual Specifications Product Name Mini Club Model No AL28 05R 30R 50R 100R 200R AL28 05G 20G 30G 4 9 30 50 100 200mW Red 4 9 20 30mW Green Laser Color R ed Model No AL28 5R5G AL28 20R10G AL28 50R20G AL28 100R30G AL28 200R50G 4 9 200mW Red amp 4 9 50mW Green Red Green and Yell
Download Pdf Manuals
Related Search