Advantech IDK-2119 User Manual
Contents
1. 21 Table 4 4 Input connector pin definition 22 Table 4 5 Output connector pin 22 V IDK 2119 User Manual Chapter 5 5 1 5 2 Appendix A Appendix B 1 IDK 2119 User Manual Figure 4 1 Dimension 22 Touch Screen amp Touch Controller23 Touch Screen Optional for IDK 2119R only 24 5 1 1 Touch Characteristics sursis reto een 24 5 1 2 Optical Characteristics 24 5 1 3 Environment CharacteristiCS 24 5 1 4 Mechanical Characteristics 24 5 1 5 Electronic Characteristics 24 5 1 6 General specification 25 Touch controller Optional for IDK 2119R 25 5 2 1 Touch Controller Characteristics 25 5 2 2 Pin Assignment and Description 26 Figure 5 1 Board mounted header 27 5 2 3 Physical dimensions een 28 Optical Characteristics 29 Optical Characterisctics 30 Table A 1 Optical Characteristics 30 Handling Precautions 33 Optical Characterisctics 34 vi Chapter 1 Overview 11 General Description The Advantech IDK 2119 series comes with a 19 1200 cd m2 industrial2. WUL OFE WWS 07002 mb 10 3 0 2mm IDK 2119 User Manual 28 Appendix Optical Characteristics A 1 Optical Characterisctics The optical characteristics are measured under stable conditions at 25 C Room Temperature Table A 1 Optical Characteristics Item Unit Conditions Min Typ Max Note Horizontal Right 75 85 CR 10 Left 75 85 Vertical Up 70 80 Viewing Angle degree a 1 Horizontal Right 75 85 CR 5 Left 75 85 Vertical Up 70 80 CR 5 Down 70 80 Luminance Uniformity 9 Points 80 85 2 3 Rising 3 6 5 7 Optical Response Time msec Falling 1 4 23 4 6 Rising Falling 5 8 Redx 0 594 0 644 0 694 Red y 0 292 0 342 0 392 Green x 0 273 0 323 0 373 Color Chromaticity Green y 0 571 0 621 0 671 ae Blue x 0 098 0148 0 198 Blue y 0 011 0 061 0 111 White x 0 263 0 313 0 363 White y 0 279 0 329 0 379 White Luminance cd m 1200 4 At LED 80mA Contrast Ratio 1100 Cross Talk At 60Hz 96 15 5 Flicker dB 20 Note Optical Equipment BM 7 DT 101 or equivalent Note1 Definition of viewing angle Viewing angle is the measurement of contrast ratioBR10 at the screen center over a 180 horizontal and 180 vertical range off normal viewing angles The 180 view ing angle range is broken down as below 90 0 horizontal left and right and 90 vertical hig
3. Item Symbol Min Max Unit Conditions LED Light Bar Current ILed 800 2 mA Note 1 2 7 IDK 2119 User Manual 1 6 3 Absolute Environmental Ratings Item Symbol Min Max Unit Conditions Operating Temperature TOP 0 50 0C Operation HOP 8 90 Storage Temperature TST 20 60 0C Storage Humidity HST 8 90 Note1 Ta must not exceed 25 C Note2 Permanent damage to the device may occur if maximum values are exceeded IDK 2119 User Manual 8 Electrical Characteristics 2 1 Power Specification Input power specifications are as follows Table 2 1 Power specification Symbol Parameter Min Typ Max Unit Condition VCC Logic LCD Drive 4 5 5 0 5 5 Voli 10 Voltage IDD Input Current 0 94 1 1 A Vin 5 0V All white pattern At 60Hz 4 7 5 5 Watt Vin 5 0V All white ues rene pattern At 60Hz IRush Inrush Current 2 1 2 5 Note 2 VCCrp Allowable Logic 300 mV p p with panel loading LCD Drive Ripple Voltage Note1 Measurement condition High to Low Control Signal 3 3V 14 01 470 us VDD rising time 64 2 1 1 Signal Electrical Characteristics Input signals shall be low or Hi Z state when VDD is off VDD LCD Module Input Gray pattern Table 2 2 Signal electrical characteristics Symbol Parameter Min Typ Max VTH Differential Input High Threshold 100 Unit Condition mV
4. 7 1 6 2 Absolute Ratings for Backlight 7 1 6 3 Absolute Environmental Ratings 8 Electrical Characteristics 9 Power Specifications 10 Table 2 1 Power specification 10 2 1 1 Signal Electrical 5 10 Table 2 2 Signal electrical characteristics 10 Backlight Driving Conditions 11 Table 2 3 Backlight driving conditions 11 Signal Characteristics 13 Pixel Format Image iita 14 Pin DSSCrIPUON messen Y 14 Table 3 1 Pin Description 44044440000 14 The nput Data Formats ea 16 Interface Timing EE 17 3 4 1 Timing Characteristics 17 Table 3 2 Timing 17 3 4 2 Input Timing 17 Power ON OFF Sequence iii 18 Connector amp Pin Assignment 19 TFT ECD Module see 20 4 1 1 Connector 20 Table 4 1 Connector 20 4 1 2 Pin 55 20 Table 4 2 Pin Assignment nnee ennen eenen 20 Backlight Unit aaa etd elen 20 4 2 1 Signal for LED light bar 21 4 2 2 LED Driver Board 21 Table 4 3 Specification
5. W Unaffected by environmental 25 IDK 2119 User Manual 5 2 1 2 5 2 2 5 2 2 1 m Panel resistance of 5 wire resistive model is from 50 to 200 ohm Pin to pin on same layer m Touch resistance under ohm Serial Interface m EIA 232E Serial RS 232 No parity 8 data bits 1 stop bit 9600 baud 8 1 9600 Wm Support Windows 2000 Vista XP 7 Windows 5 0 6 0 7 0 Windows Linux DOS QNX USB Interface Conforms to USB Revision 1 1 full speed m If the USB is connected to the controller the controller will communicate over the USB and will not communicate over the serial port Support Windows 2000 Vista XP 7 Windows 5 0 6 0 7 0 Linux QNX Touch Resolution m 2 048 x 2 048 resolution Response Time B Max 20 ms Environmental Features Reliability B MTBF is 200 000 hours Temperature Ranges Operating 25 85 C m Storage 25 C 85 C Relative Humidity W 95 at 60 C RH Non condensing RoHS certificate complete Requlatory FCC B CE approvals complete Dimensions 75 mm x 20 mm x 10 mm Pin Assignment and Description Connector and LED Locations JP1 Connector USB amp RS 232 Combo Inerface JP2 Connector 5 wire Touch screen Interface LED IDK 2119 User Manual 26 5 2 2 2 Combo Interface Connector JP1 Pins and signal descriptions combo interface connector USB RS 232 is a box 2 0 10 pins 90 degree Male type
6. Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem 5 2 Call your dealer describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain RMA return merchandise authorization number from your d
7. IDK 2119 Series 19 High Brightness SXGA LED Backlight AD ANTECH Enabling an Intelligent Planet Copyright The documentation and the software included with this product are copyrighted 2013 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements AMI is a trademark of American Megatrends Inc IBM and PC are trademarks of International Business Machines Corporation Intel Core 2 Quad Pentium Dual Core and Celeron are trademarks of Intel Corpo ration WinBond is a trademark of Winbond Corporation All other product names or trademarks are properties of their respective owners Part No 2006211910 Edition 2 Printed in China Jan 2013 IDK 2119 User Manual ii A Message to the Customer Advantech Customer Services Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of indus trial environmen
8. VCM 1 2V VTL Differential Input Low Threshold 100 mV VCM 1 2V VID Input Differential Voltage 100 400 600 mV VICM Differential Input Common Mode 1 0 5 1 45 VTH VTL Voltage 100mV IDK 2119 User Manual 10 2 2 Note LVDS Signal Waveform Differential Signal V gt VTH High Backlight Driving Conditions Parameter guideline for LED Light Bar Driver is under stable conditions at 25 C Room Temperature Table 2 3 Backlight driving conditions Item Symbol Values Unit Condition Min LED Voltage VL 19 2 V Note 2 3 LED Current IL 800 2 mA Note 2 LED life time 50 000 Hr Note 1 Note1 The LED lift time is defined as the module brightness decrease to 50 origi nal brightness that the ambient temperature is 25 C and typical LED Current at 800 mA Note2 The LED driving condition is defined for each LED module 6 LED Serial Note3 The variance of LED Light Bar power consumption is 1096 Calculator value for reference IL x VL x 2 PLED 11 IDK 2119 User Manual LEDO1 LEDO1 LEDO2 LEDO3 LEDO4 LEDOS LEDO6 IDK 2119 User Manual 12 Chapter 3 Signal Characteristics 3 1 Pixel Format Image Following figure shows the relationship between input signal and LCD pixel format 1st Line 1024th Line 2 1279 1280 3 2 Pin Description The module uses a pair of LVDS receiver SN75LVDS82 Texas Instruments or
9. 30 40 50 ms T3 175 ms T4 10 ms T5 10 ms T6 0 ms 7 10 ms T8 100 ms T9 0 16 50 ms T10 ms T11 1000 ms IDK 2119 User Manual 18 Connector amp Pin Assignment 4 1 4 1 1 4 1 2 4 2 TFT LCD Module Physical interface is described for the connector on the module These con nectors are capable of accommodating the following signals and will be fol lowing components Connector Table 4 1 Connector Connector Name Description Interface Connector Interface card Manufacture JAE P TWO Type Part Number FI XB30SSLA HF15 187034 30091 Mating Housing Part Number FI X30HL FI X30H Unlocked Type Pin Assignment Table 4 2 Pin Assignment Pin No Signal Name Pin No Signal Name RxOINO 2 RxOINO 3 RxOIN1 4 RxOIN1 5 RxOIN2 6 RxOIN2 7 VSS 8 RxOCLKIN 9 RxOCLKIN 10 RxOIN3 11 RxOIN3 12 RxEINO 13 RxEINO 14 VSS 15 RxEIN1 16 RxEIN1 17 VSS 18 RxEIN2 19 RxEIN2 20 RxECLKIN 21 RxECLKIN 22 RxEIN3 23 RxEIN3 24 VSS 25 VSS 26 NC 27 VSS 28 VCC 29 VCC 30 VCC Backlight Unit Physical interface is described as for the connector on module These connectors are capable of accommodating the following signals and will be following components Connector Name Designation LED Light Bar Connector Backlight Manufacturer STM Type Part Number MS24019R Mating Type Part Number P24019 ID
10. com patible LVDS is a differential signal technology for LCD interface and high speed data transfer device Transmitter shall be SN75LVDS83 negative edge sampling or compatible The first LVDS port RxOxxx transmits pixels while the second LVDS port RxExxx transmits even pixels Table 3 1 Pin Description PinNo Symbol Description 1 RxO0 Negative LVDS differential data input Odd data 2 RxO0 Positive LVDS differential data input Odd data 3 RxO1 Negative LVDS differential data input Odd data 4 RxO1 Positive LVDS differential data input Odd data 5 RxO2 Negative LVDS differential data input data H Sync V Sync DSPTMG 6 RxO2 Positive LVDS differential data input Odd data H Sync V Sync DSPTMG 7 VSS Power Ground 8 RxOC Negative LVDS differential clock input Odd clock 9 RxOC Positive LVDS differential clock input Odd clock 10 RxO3 Negative LVDS differential data input Odd data 11 RxO3 Positive LVDS differential data input Odd data 12 RxEO Negative LVDS differential data input Even data 13 RxE0 Positive LVDS differential data input Even data 14 VSS Power Ground IDK 2119 User Manual 14 Table 3 1 Pin Description 15 RxE1 Negative LVDS differential data input Even data 16 RxE1 Positive LVDS differential data input Even data 17 VSS Power Ground 18 RxE2 Negative LVDS differential
11. data input Even data 19 RxE2 Positive LVDS differential data input Even data 20 RxEC Negative LVDS differential clock input Even clock 21 RxEC Positive LVDS differential clock input Even clock 22 RxE3 Negative LVDS differential data input Even data 23 RxE3 Positive LVDS differential data input Even data 24 VSS Power Ground 25 VSS Power Ground 26 No contact 27 VSS Power Ground 28 VCC 5 0V Power Supply 29 VCC 5 0V Power Supply 30 VCC 5 0V Power Supply 15 IDK 2119 User Manual 3 3 The Input Data Format RX O E C KE RXinOO JR Cons ons ORD RXinO2 DD T I D 085 KK 082 Previous Cycle Current Cycle Signal Name Description Remark R7 Red Data 7 R6 Red Data 6 R5 Red Data 5 R4 Red Data 4 Red pixel Data For 8 bits LVDS input MSB R5 R3 Red Data 3 LSB RO R2 Red Data 2 R1 Red Data 1 RO Red Data 0 G7 Green Data 7 G6 Green Data 6 G5 Green Data 5 G4 Green Data 4 Green pixel Data For 8 bits LVDS input MSB G3 Green Data 3 G7 LSB GO G2 Green Data 2 G1 Green Data 1 GO Green Data 0 B7 Blue Data 7 B6 Blue Data 6 B5 Blue Data 5 B4 Blue Data 4 Blue pixel Data For 8 bits LVDS input MSB B7 B3 Blue Data 3 LSB BO B2 Blue Data 2 B1 Blue Data 1 BO Blue Data 0 RxCLKIN LVDS Data Clock DE Data Enable Signal When the signal is high the pixel data shall be valid to be displayed VS Vertical Syn
12. with lock connector intended to be used with single wired pins in 5 5 pins header The pins are numbered as shown in the table below USB Signal Signal Function RS 232 Signal Signal Function Pin Name Pin Name 1 G Ground 1 G Ground 2 V USB Power 2 V Power 3 G Ground 3 G Ground 4 D USB D 4 TxD Serial Port 5 D USB D 5 RxD Serial Port Signal DB 9 pin 5 232 pin Sourced by Signal Description Name RxD 2 5 ctlr serial data from controller to host TxD 3 4 host serial data from host to controller USB Interface G V D D 1 5 G V G Tx Rx RS232 Interface Figure 5 1 Board mounted header 5 2 2 3 Touch Screen Connector JP2 Pins and signal descriptions The Touch Screen connector JP2 is a single row by 2 54mm 5 pins 90 degree Male type connector The pins are numbered as shown in the table below JP2 Signal Name Signal Description Pin 4 1 H UR Drive signal attached to the touchscreen substrate upper right corner when viewed from a user s perspective 2 Y UL Drive signal attached to the substrate upper left corner 3 COM 4 X LR Drive signal attached to the substrate lower right corner 5 L LL Drive signal attached to the substrate lower left corner COM HX SYL LRLL EEE 1 5 1 5 5 1 27 IDK 2119 User Manual 5 2 3 Physical dimensions ETM RES04C EEH4EE Touch Control Board Unit mm 75 0 0 5mm OF
13. K 2119 User Manual 4 2 1 Signal for LED light bar connector 4 2 2 4 2 2 1 ConnectorNo Pin No Input Color Function Upper CN1 1 HI 1 Red Power supply for backlight unit 2 GND 1 Black Ground for backlight unit Lower CN2 1 2 Red Power supply for backlight unit 2 GND 2 Black Ground for backlight unit Cable Length 250mm 10mm LED Driver Board Specification Table 4 3 Specification Symbol Characteristics Condition Min Typ Max Unit Voltage 10 12 15 V Efficiency Vin 12V 85 Input lout 800mA Vout 19 2V Power 3 30 W Voltage 19 2 V Current 150 800 mA Output Current Accurancy 150mA lt lout lt 1000 5 10 mA Protection Thermal OVP Thermal Shutdown 165 C Operating Junction 125 C Temperature Environment Operating 20 70 C ture Storage Temperature 40 85 C Dimmer range Note 5 100 V 1 PWM Dim Dimmer VH 3 5 V mer E Dimmer VL 0 15 V Dimmer Frequency 0 25 0 5 1 KHz ON OFF Von 3 5 5 V off 0 2 V KHK on 5 Note When the input x 1KHz the high level digital output must be greater than the total output level of only 5 21 IDK 2119 User Manual 4 2 2 2 Input connector pin definition Table 4 4 Input pin definition Pin No Pin Definition Vin 12V Vin 12V GND GND ON OFF OV 5V On Dimming PWM RWIN 4 2 2 3 Output connector pin def
14. SXA2E Front View r 2 75 0 1 T 4 IE DID H olo ON ale SIW an zo 4 PIN a 0 S boy 1 301 06 0 3 Active Area 9 5 305 06 0 3 Bezel Size 324 0 0 5 4 3 IDK 2119 User Manual Rear View 17 8 0 5 IDK 2119 User Manual 1 3 2 IDK 2119R K2SXA2E Front View fra 5 1 158 33 9602 lt 6 e nov S IJE LE 0 968 7 302 05 T S Active Area 316 65 Touch 324 0 5 IDK 2119 User Manual Rear View IDK 2119 User Manual 1 4 Functional Block Diagram The following diagram shows the functional block of the 19 inch color TFT LCD mod ule TFT LCD 1280 3 1024 Pixels Figure 1 1 Function block diagram 1 5 Touch Screen Driver The T S driver CD ROM is in the accessory box and comes with the product 1 6 Absolute Maximum Ratings Absolute maximum allowable ratings for this module are as follows 1 6 1 Absolute Ratings for TFT LCD Module Item Symbol Min Max Unit Conditions Logic LCD Drive Voltage Vin 0 5 5 5 Volt Note 1 2 1 6 2 Absolute Ratings for Backlight Unit
15. chronous Signal IDK 2119 User Manual 16 HS Horizontal Synchro nous Signal Note Output signals from any system shall be low or Hi Z state when VDD is off 3 4 Interface Timing 3 4 1 Timing Characteristics Table 3 2 Timing Characteristics Signal Item Symbol Min Max Unit Period Ty 1032 1066 1150 TH Vertical oh Active 1024 1024 1024 Ty Blanking Tbp yy 8 42 126 TH Period TH 780 844 2047 Horizontal 5 Section Active 640 640 640 TGlock Blanking PWus 140 204 TClock Period T Glock 22 2 18 52 14 81 ns Clock Frequency Freq 45 54 67 5 MHz Frame Rate Frequency 1 Ty 50 60 75 Hz Note DE mode 3 4 2 Input Timing Diagram tt TE mm Dn 0 _____ Data m a Pixel Pixel xs pu s UE X 1 3 5 7 9 5 rs RGB Data r e X ses DE Ps Ins s De meme D 11 17 IDK 2119 User Manual 3 5 Power ON OFF Sequence VDD power and lamp on off sequence is as follows Interface signals are also shown in the chart Signals from any system shall be Hi Z state or low level when VDD is off LVDS VCC PWM Dimming Back Light ON OFF Power Sequence Timing Parameter Value Unit Min Typ Max T1 0 5 10 ms T2
16. e it should be taken into consideration that no bending twisting forces are applied to the TFT Module otherwise the TFT Module may be damaged A small amount of material having no flammability grade is used in the LCD module The LCD module should be supplied by power complying with require ments of Limited Power Source IEC60950 or UL1950 or an exemption applied for IDK 2119 User Manual 34 Enabling an Intelligent Planet www advantech com Please verify specifications before quoting This guide is intended for reference purposes only All product specifications are subject to change without notice No part of this publication may be reproduced in any form or by any means electronic photocopying recording or otherwise without prior written permis sion of the publisher All brand and product names are trademarks or registered trademarks of their respective companies Advantech Co Ltd 2013
17. ealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer IDK 2119 User Manual iv Contents Chapter Chapter Chapter Chapter 1 1 3 1 4 2 1 2 2 3 3 1 3 2 3 3 3 4 3 5 4 4 1 4 2 General Description 2 sheet 2 1 2 1 ECD Panels ina rr aep 2 12 2 LED Driver Board 2 1 2 3 Touch Screen series 2 1 2 4 napa 2 Mechanical 3 1 3 1 IDK 2119N K2SXA2E nase aan 3 1 3 2 IDK 2119R K2SXA2E 5 Functional Block Diagram 7 Figure 1 1 Function block diagram 7 Touch Screen nee ae 7 Absolute Maximum Ratings 7 1 6 1 Absolute Ratings for TFT LCD
18. grade LCD display and an LED driver board The series is also available with flexible options for touch screens and enhanced treatment such as AR surface treatment and optical bonding solution IDK 2119 series supports 1200 cd m2 high brightness with low power consumption at the maximum consumption of 29 61 W Equipped with high level of brightness and wide operating temperature IDK 2119 provides superior sun light readability and is perfect for applications whether in semi outdoor or outdoor environments 1 2 Specifications 1 2 1 LCD Panel Display Size 19 LED backlight panel Resolution 1280 x 1024 Viewing Angle U D L R 80 80 7 85 9859 Brightness 1200 cd m Contrast Ratio 1100 1 Response Time ms 5ms Colors 16 7 M Voltage 5V Power Consumption 41 14W Signal Interface 2 channel LVDS Weight R series 2800 Typ N series 1700 Typ Dimensions W x Hx D R series 396 H x 324 V x 20 7 D Typ N series 396 H x 324 V x 17 8 D Typ 1 2 2 LED Driver Board W Efficiency 85 Output Current amp Voltage 800 mA 19 2 Max m Dimensions W x Hx D 80 x 42 x 6 5 mm 1 2 3 Touch Screen R series Touch Screen 5 Wire Resistive Light Transmission 80 3 Durability 10 million times 1 2 4 Environment B Operating Temperature 0 50 C m Storage Temperature 20 60 C Humidity 8 90 25 C non condensing IDK 2119 User Manual 2 1 3 Mechanical Characteristics 1 3 1 IDK 2119N K2
19. h up and low down The measurement direction is typically perpen dicular to the display surface with the screen rotated to its center to develop the desired measurement viewing angle Normal Line 70 0 0 12 O clock 0 On direction 0 290 x a y 90 6 O clock x direction 90 Or 90 IDK 2119 User Manual 30 Note2 9 points position 90 50 10 10 90 Note3 The luminance uniformity of 9 points is defined by dividing the maximum lumi nance values by the minimum test point luminance Minimum Brightness of nine points 6 Maximum Brightness of nine points Note4 Measurement method The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring In order to stabilize the luminance the measurement should be executed after lighting Backlight for 30 minutes in a stable windless and dark room Optical Equipment DT 100 or equivalent Photo detector TFT LCD p Module ze ICD Panel Note5 Definition of response time The output signals of photo detector are measured when the input signals are changed from Full Black to Full White rising time and from Full White to Full Black falling time respectively The response time is interval between the 10 and 90 of amplitudes Please refer to the fig
20. ics Specification Remarks 1 Rated Voltage DC 7V max 2 Resistance X axis 2000 500Q Figure as bellow FPC connector axis 2000 800Q Figure as bellow 3 Linearity X lt 1 5 Figure as bellow Reference 250gf lt 1 5 Figure as bellow 4 Chattering lt 15ms Max 5 Insulation gt 20MQ min DC 25V Resistance IDK 2119 User Manual 24 5 1 6 General specification 5 2 5 2 1 5 2 1 1 Item Specification 1 Frame size 393 40 0 50 X 316 65 0 50 mm 2 View Area 380 90 0 20 X 305 65 0 20 mm 3 Active Area 377 30 0 20 X 302 05 0 20 mm 4 Total Thickness 3 20 0 20 mm 5 Tail length 305 00 6 00 mm Touch controller Optional for IDK 2119R only Advantech ETM RESO4C Touch Control Board is the ultimate combo board This touch panel controller provides optimum performance for analog resistive touch pan els for 5 wire models It communicates with PC system directly through USB and RS 232 connector You can see how superior the design is in sensitivity accuracy and friendly operation The touch panel driver emulates mouse left and right button func tions and provides the following features Touch Controller Characteristics Specifications Electrical Features m 5 Vdc 100 mA typical 50 peak to peak maximum ripple and noise Bi directional RS 232 serial communication and USB 1 1 full speed Report rate of RS 232 is 180 points sec max And USB is 200 points sec max
21. inition Table 4 5 Output pin definition Pin No pin definition 1 VLED 2 VLED 4 2 2 4 Dimension x4 4 6 0 5mm 6 5 mm 0 5mm 80 mm 0 5mm Figure 4 1 Dimension IDK 2119 User Manual 22 Touch Screen amp Touch Controller 5 1 5 1 1 5 1 2 5 1 3 5 1 4 5 1 5 Touch Screen Optional for IDK 2119R only Touch Characteristics TOUCH PANEL is resistance type that customer uses with flat display like LCD Once operator touches it either with round ended resin PEN or FINGER the circuit for TOUCH PANEL sends coordinate point to PC from voltage at contact point Optical Characteristics Specification Remarks 1 TRANSPARENCY 80 3 BYK Gardner 2 HAZE 8 0 3 BYK Gardner Environment Characteristics Specification Remarks 1 Operation temperature 20 C 70 C Note All terms under 1 2 Storage temperature 40 C 80 C atmosphere 3 Operation Humidity 20 80 RH 4 Storage temperature 20 90 RH Mechanical Characteristics Item Specification Remarks 1 Hardness of surface Pencil hardness 3H JIS K 5600 5 4 150gf 45 degree 2 FPC peeling strength 1 5N BN Min 1 Peeling upward by 90 2 19 6N 19 6N Min 2 Peeling downward by 90 3 Operation force Pen 0 05 1 96 Dot Spacer Finger 57200098 Within guaranteed active area but not on the age and Dot Spacer Electronic Characterist
22. ts Whether your new Advantech equipment is destined for the labo ratory or the factory floor you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known Your satisfaction is our primary concern Here is a guide to Advantech s customer services To ensure you get the full benefit of our services please follow the instruc tions below carefully Technical Support We want you to get maximum performance from your products So if you run into technical difficulties we are here to help For the most frequently asked questions you can easily find answers in your product documentation These answers are nor mally a lot more detailed than the ones we can give over the phone So please consult this manual first If you still cannot find the answer gather all the information or questions that apply to your problem and with the product close at hand call your dealer Our dealers are well trained and ready to give you the support you need to get the most from your Advantech products In fact most problems reported are minor and are able to be easily solved over the phone In addition free technical support is available from Advantech engineers every busi ness day We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products iii IDK 2119 User Manual Product Warranty 2 years
23. ure as below Tf Tr Optical response 31 IDK 2119 User Manual IDK 2119 User Manual 32 Appendix B Handling Precautions B 1 Optical Characterisctics The optical characteristics are measured under stable conditions at 25 C Room Temperature 1 2 Since front polarizer is easily damaged be careful not to scratch it Be sure to turn off power supply when inserting or disconnecting from input con nector Wipe off water droplets immediately Long contact with water may cause discol oration or spots When the panel surface is soiled wipe it with absorbent cotton or other soft cloth Since the panel is made of glass it may break or crack if dropped or if it collides with a hard object Since CMOS LSI is used in this module take care of static electricity and insure human earthing when handling Do not open or modify the Module Assembly Do not press the reflector sheet at the back of the module to any direction In case a Module has to be put back into the packing container slot after it was taken out from the container please press at the far ends of the LED light bar reflector edge lightly Otherwise the TFT Module may be damaged When inserting or removing the Signal Interface Connector be sure not to rotate nor tilt the Interface Connector of the TFT Module After installation of the TFT Module into an enclosure do not twist nor bend the TFT Module even momentarily When designing the enclosur
Download Pdf Manuals
Related Search