Tesco_EJ09_Sewing_MachineIB_V0_en PDF
Contents
1. Insert a new needle Insert the needle correctly flat side towards the back Choose a needle to suit the thread and fabric Select the correct foot Check the threading Thread the bobbin case as illustrated The needle size must suit the fabric and thread Correct the thread tension Select a finer needle Readjust the stitch length Loosen the thread tension Select a better quality thread Remove bobbin case and retread and insert correctly Do not pull on the fabric while sewing let it be taken up by the machine Lubricate as described Clean the hook and feed dog as described Only use good quality sewing machine oil Replace the needle Remove the upper thread and bobbin case turn the handwheel backwards and forwards by hand and remove the thread remands Lubricate as described BR WwN WN WN e BWYN BWYN AU Nae WN S DU B W NN Page 35 CONCLUSION AFTER USE Disconnect the machine from the power supply by removing the plug from the mains socket Remove the cord connecting the foot pedal Store the machine securely together with all accessories in a cool dry place away from heat and damp and where it cannot be interfered with by children or pets CLEANING THE CASE The case of the sewing machine may be cleaned with a barely damp cloth and then dried thoroughly Do not wet the appliance body cord or mains plug NEVER allow water to penetrate the case or foot pedal CAUTION2. 2 Stitch along the edge pulling both threads slightly when beginning to sew Use thicker than normal threads for sewing 3 After sewing remove the basting and the paper To finish tie knots on the reverse side at the beginning and the end of the seams Page 29 APPLIQUE STITCH LENGTH DIAL STANDARD FOOT Turn stitch length dial to the desired length Turn pattern selector dial to small zigzag width 3 Cut out the appliqu design and baste it to the fabric Sew slowly around the edge of the design Trim excess material outside the stitching Make sure not to cut any stitches Remove the basting thread Tie top and bottom thread under the appliqu to avoid unravelling Page 30 MONOGRAMMING AND EMBROIDERING 1 USING AN EMBROIDERY HOOP NOT SUPPLIED STITCH LENGTH DIAL PREPARATION Set the machine as illustrated opposite The 0 setting means the machine will not feed the fabric leaving you to manoeuvre it freely yourself Remove the presser foot and the presser foot holder Attach the darning plate Lower the presser foot lever before starting to sew Adjust the stitch width according to the size of lettering or design OPERATION 1 Draw the desired lettering or design on the right side of the fabric Stretch the fabric between embroidery hoop as firmly as possible Place the fabric under the needle Make sure the presser foot bar is down in its lowest position Turn the balance wheel towards you
3. LENGTH DIAL Install the Button Sewing Foot Install the Darning Plate See Fig 1 Position the work under the foot Place the button on the marked position and lower the foot Set the pattern selector knob on B and sew a few securing stitches Select the zig zag stitch width according to the distance between the two holes of the button Turn the handwheel to check if the needle goes into the right and the left hole of the button without any obstruction adjust the stitch width according to the button Slowly sew on the button with about 10 stitches Select pattern B and sew a few securing stitches If a shank is required place a darning needle on top of the button and sew Fig 3 For buttons with 4 holes sew through the front two holes first Fig 2 push the work forward and then sew through the back two holes as described Fig 3 Page 22 SEWING BUTTONHOLES Preparation Attach the buttonhole foot Adjust the stitch length dial between STITCH LENGTH DIAL BUTTONHOLE FOOT 0 5 1 The density of the stitch depends on thickness of the fabric Note Always test sew a buttonhole aq To prepare the fabric Measure the diameter of the button and add 0 3 cm 1 l I 1 8 for the bartacks If you have a very thick button add more to the diameter X 3 2 measurement Mark the position and length of the buttonhole on the fabric i Position the fabric so that the needle is on the mark that is furthest f
4. Never use scouring pads abrasives or harsh cleaners TESCO WARRANTY Your TESCO appliance is covered by a warranty for 12 months from the date of purchase If a fault develops during this period please contact the TESCO electrical help line on 0845 456 6767 Please have your original purchase receipt with you when you call This warranty in no way affects your consumer rights UK Waste electrical products should not be disposed of with household waste Separate disposal facilities exist for your nearest facilities See ps www recycle more co uk or in store for details ROI Produced after 13th August 2005 Waste electrical products should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice ww aaa ESCO Stores Ltd Delamare Road Cheshunt Herts EN8 9SL
5. Triple zig zag is suitable for firm fabrics like denim corduroy etc WWVINVMINININININ SMOCKING STITCH STITCH LENGTH DIAL STANDARD FOOT Use for seams hems T shirts underwear etc Set the machine as illustrated Fig 1 Pattern selector D stitch length S1 This stitch can be used for all types of jersey as well as for woven fabrics Fig 2 Sew at 1 cm 1 4 from the fabric edge and trim the surplus fabric Fig 3 Page 27 DECORATIVE AND PRACTICAL STITCHES STITCH LENGTH DIAL Set the machine as illustrated Turn the stitch length dial to suit the fabric Shell hem Fig A For decorative edges Suitable for edges on sheer fine and stretch fabrics The larger stitch should go just over the edge of the fabric to create the shell effect Rampart Fig B For flat joining seams sewing on elastic visible hems This stitch can be used for firm thicker fabrics Bridging Fig C For seams place mats tablecloths Decorative joining seam for a fagoted effect Gathering with cord or shirring elastic Page 28 STANDARD FOOT PATCHING STITCH LENGTH DIAL STANDARD FOOT These stitches are used to join two pieces of fabric while leaving a space between their edges Set the pattern selector on H Turn the stitch length dial to S1 1 Fold over the edges of the two pieces of fabric for the hem and baste the edges to a thin piece of paper leaving a small space between them
6. 9 11 65 75 Light duty thread in cotton nylon or polyester fabrics and needle sizes 14 90 Medium weight fabrics cotton duck woollen heavier knits terry cloth Use polyester threads on synthetic materials and cotton on denims natural woven fabrics for best results 16 100 Heavyweight fabrics canvas woollens outdoor tent and quilted fabrics Always use the same thread on top and bottom denims upholstery material light medium 18 110 Heavy woollens overcoat fabrics upholstery fabrics some leathers and Heavy duty thread carpet thread Use heavy foot vinyls pressure large numbers IMPORTANT Match needle size to thread size and weight of fabric NEEDLE FABRIC SELECTION NEEDLES EXPLANATION TYPE OF FABRIC Standard sharp needles Sizes range thin to large 9 Natural woven fabrics wool cotton silk etc Not 65 to 18 110 recommended for double knits Natural and synthetic woven fabrics polyester blends Knits polyesters 15x1 705H SUK Semi ball point needle scarfed 9 65 to 18 110 interlocks tricot single and double knits Can be used instead of 15x1 for sewing all fabrics 15x1 705H SUK Full ball point needle 9 65 to 18 110 Sweater knits Lycra swimsuit fabric elastic Leather vinyl upholstery Leaves smaller hole than standard 130 PCL Leather needles 12 80 to 18 110 large needle Page 21 SEWING ON BUTTONS Set the Stitch Length Dial and the Pattern Selector as shown STITCH
7. AILS OF THE MACHINE REAR VIEW Spool pin Bobbin winder Hole for second spool pin Hand wheel Patten selector dial Power switch Main plug socket Bobbin thread guide Upper thread guide Handle Presser foot lever Page 5 SUPPLIED ACCESSORIES Standard foot Zipper foot Buttonhole foot Button sewing foot L screwdriver Seam ripper brush Lubricating Oil bottle Pack of 3 needles EEN Seam guide 3 Bobbins Darning plate Spool holder Second spool pin LSS Spool pin felt JO sun ff YS J K H Oa M N Page 6 FITTING THE SNAP IN SEWING TABLE Hold the the snap in sewing table horizontal and push it in the direction of the arrow The inside of the snap in sewing table can be utilized as an accessory box Page 7 CONNECTING POWER Switch the machine s Power Switch OFF 0 position Plug in the Machine Power connector firmly Plug in the Mains Plug to the mains supply and switch on ye PS Adjust the position of the foot controller see Fig 2 below Now remove your foot from the control r F Switch the machine s Power Switch ON I position Your sewing machine is now ready for use Place the Foot Controller in a convenient unobstructed place Page 8 ATTACHING THE NEEDLE The Presser Foot Assembly is raised and lowered with the Preser Foot Lever No 23 on PXX This also raises and lowers the needle Insert the needle following the illustrated i
8. EJO9 Sewing Machine User Manual IMPORTANT SAFETY GUIDE Please follow all the precautions listed below for safety and to reduce the risk of fire injury or electrical shock Read all the instructions before operating the appliance and keep them for future reference If you pass the product on to a third party include these instructions Always unplug the sewing machine from the mains supply when removing covers lubricating or when making any user or servicing adjustments mentioned in the instruction manual Do not unplug the unit by pulling on the cord To unplug grasp the plug not the cord Ensure there is adequate room to operate the unit Never operate this appliance if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped into water Return the appli ance to a competent service centre for examination repair electrical or mechanical adjustment This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of this appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Do not use outdoors or in damp or wet conditions Before operating ensure that the surface on which the unit is placed is stable Never operate the applianc
9. Foot Refer to figure 3 Raise the presser foot Raise the lever e and the foot disengages To Attach the Seam Guide Refer to figure 4 The seam guide is a useful accessory to help you gauge the position of seams etc but its use is not essential Attach the seam guide g in the slot as illustrated Adjust according to need for hems pleats etc WINDING THE BOBBIN Your sewing machine works by stiching two threads The main thread is contained on the spool which is at the top of the machine A second thread is contained in a compartment under the machine This thread is wound onto a bobbin from the main spool Place the main spool as shown in the top illustration For large spools of thread place the spool holder with the large side next to the spool Fig 1 For small spools of thread place the spool holder with the small side next to the spool Fig 2 To wind the bobbin Wind thread clockwise around bobbin winder tension disc Fig 3 Thread the bobbin as illustrated and place on spindle Fig 4 Push the bobbin to the right Fig 5 This is the bobbin winding position Hold the thread end Fig 6 Switch the power on Step on the foot control pedal Fig 7 Gradually apply pressure to increase speed Allow the bobbin to wind sufficient thread Remove your foot from the pedal Now cut the threads 8 Press the bobbin to left 9 and remove Moving the bobbin to the left places the machine in the
10. Noise Performance SPL 75dBA Net Weight XXXXX CE Page 2 CONTENTS Safety Guide Details of the machine Front View Details of the machine Rear View Accessories Fitting the snap in sewing table Connecting power Attaching the needle The presser foot Winding the bobbin Inserting the bobbin Checking the bobbin tension Threading the upper thread Bringing up the lower thread Basic sewing Reverse sewing Removing the work More about Straight Stitching Zig Zag stitching Adjusting the upper thread tension More about the pressure foot Matching the needle fabric and thread Sewing on buttons Sewing buttonholes Attaching zippers and piping 3 step Zig Zag sewing Stitch selection Smocking stitch Decorative and practical stitches Patching Appliqu Monogramming and embroidering 1 Monogramming and embroidering 2 Maintenance 1 Replacing the Light Bulb Maintenance 2 Cleaning and Lubrication Troubleshooting After Use Care Warranty Page 3 Page 20 Page 21 Page 24 Page 25 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 36 Page 36 DETAILS OF THE MACHINE FRONT VIEW eee aS eS eS Thread tension dial Presser foot pressure Thread take up lever Thread cutting Presser foot Needle plate Sewing table Accessories box Bobbin stopper Stitch length dial Stitch display Reverse sewing lever Base Page 4 DET
11. bobbin case is not inserted correctly The bobbin case is threaded wrongly The lower thread tension is too tight The needle is not inserted correctly The needle is damaged The wrong size needle has been used The foot is not attached correctly The needle is damaged The needle is not correctly inserted Wrong needle size for the fabric The wrong foot is attached The machine is not correctly threaded The bobbin case is not correctly threaded Needle fabric thread combination is wrong Thread tension wrong The needle is too thick for the fabric The stitch length is wrongly adjusted The thread tension is too tight Poor quality thread The bobbin case is wrongly threaded Fabric has been pulled The machine must be lubricated Fluff or oil have collected on the hook or needle bar Poor quality oil has been used The needle is damaged Thread is caught in the hook Rethread the machine Reduce the thread tension lower number Select a larger needle Remove and reinsert the needle flat side towards the back Remove the reel and wind thread onto reel Replace the needle Reinsert the bobbin in the case The thread should pull easily Check both bobbin and bobbin case Loosen lower thread tension as described Remove and reinsert needle flat side towards the back Insert a new needle Choose a needle to suit the thread and fabric Check and attach the foot correctly
12. e stitch plate Figure 1 Turn the handwheel until the needle is fully raised Open the hinged front cover and unscrew the needle plate screw withe the screw driver Cleaning the feed dog Figure 2 Remove the bobbin case and use the brush supplied to clean the whole area Cleaning and lubricating the hook Figure 3 Remove the bobbin case Snap the two hook retaining arms A outwards Remove the hook race cover B and the hook C and clean withe a soft cloth Lubricate at the point D 1 2 drops with sewing machine oil ONLY Turn the handwheel until the hook race E is in the left position Replace the hook C Replace the hook race cover B and snap back the two hook retaining arms A Insert the bobbin case and bobbin and replace the stitch plate TROUBLESHOOTING If your machine is not working saftactorily please work through this checklist before returning it to Tesco or taking it for service The upper thread breaks The lower thread breaks Skipped stitches Needle breaks Loose stitches Seams gather or pucker Uneven stitches uneven feed The machine is noisy The machine jams Bf WN WNT WN Bw Rh B Ww PN B WN S WKN AD UT BW DN The machine is not threaded correctly The thread tension is too tight The thread is too thick for the needle The needle is not inserted correctly The thread is round wound the spool holder pin The needle is damaged The
13. e with any air openings blocked Keep all ventilation openings of the sewing machine and foot controller free from accumulations of lint dust and loose cloth Do not insert any object into ventilation slots Keep fingers away from all moving parts Special care is required around the sewing machine needle Always use the proper needle plate The wrong plate can cause the needle to break Do not use broken deformed or blunt needles Do not pull or push fabric while stitching It may deflect the needle causing it to break Switch the sewing machine off when making any adjustments in the needle area such as threading the needle changing needles threading bobbins changing the presser foot and the like Do not operate where aerosol spray products are being used or where oxygen is being administered This appliance is only for household use Industrial or professional use will invalidate the warranty Do NOT use this appliance for any purpose not covered by the instructions THE APPLIANCE MUST NOT BE LEFT UNATTENDED WHILE IT IS CONNECTED TO THE SUPPLY MAINS ELECTRICAL INFORMATION Before using this appliance ensure that the voltage of your electricity supply is the same as that indicated on the appliance The means of disconnecting this appliance from the mains supply is the mains plug This should be unobstructed and readily operable at all times SPECIFICATIONS Voltage Rating 220 240V AC 50Hz Power Consumption XXXXXXXXX
14. ias strip to form a welt Fig 3 Set the stitch length control between 1 4 according to thickness of fabric Page 24 3 STEP ZIG ZAG SEWING STITCH LENGTH DIAL STANDARD FOOT Use this technique for sewing on lace and elastic darning mending reinforc ing edges Set the machine as illustrated Figure1 Place patch in position The stitch length can be shortened to produce very close stitches Fig A a iat TT TA Me Me NO MES ON MES MM MEO hes L A When mending tears it is advisable to use a piece of backing fabric to reinforce The stitch density can be varied by adjusting the stitch length First sew over the center and then overlap on both sides Depending on the type of fabric and damage sew between 3 and 5 rows Fig B v Ye ANAN ANAON UNA NUN A NIN hA h AA y h 4 A h N Taa ee OR CO a a We a Wm Wea Wn T X Va Fe eRe ee a er Ge ey ak ee oe ae ek LOM MOM YEO MVE ON ENE MONE VOOM YE OM WES Wee BE ORE AE OR RE OR A RAS AA A OA A ws VV MOYEN OME I NE MEN MME AE OMEN u Page 25 STITCH SELECTION STITCH LENGTH DIAL Triple straight stitch Fig 1 For hardwearing seams Turn the stitch length dial to S1 The machine sews two stitches forwards and one stitch backwards This gives triple reinforcement Triple zig zag 2 STITCH LENGTH DIAL For hardwearing seams hems and decorative seams Turn the stitch length dial to S1
15. nstructions Fig 1 Loosen the needle clamp screw A Insert the needle with the flat side towards the back B and the eye facing the front C Push the needle as far as it will go D Re tighten the screw Change the needle regularly especially if it is showing signs of wear and causing problems Needles must be in perfect condition Fig 2 Problems can occur with A Bent needles B Blunt needles C Damaged points Attention ALWAYS swith the power off when attaching needles CAUTION Always exercise care when attaching needles Store needles HEE deter safely away from children and pets and dispose of them with great H care with the points protected THE PRESSER FOOT The Presser Foot Assembly is raised and lowered with the Preser Foot Lever No 23 on PXX E c First switch the power off B AK To attach the Presser Foot Holder Refer to figure 1 D A Raise the presser foot clamp Ce F B Attach the presser foot holder as illustrated STANDARD FOOT You can use the provided screw driver to loosen and tighten the screw To attach the Pressure Foot Refer to figure 2 Place the All Purpose foot F on the needle plate Gradually lower the presser foot holder B until the cut out C is directly above the pin D on the plate Raise the lever E Lower the presser foot holder fully onto the presser foot and the presser foot will lock automatically in place Release the lever To remove the Pressure
16. of the presser foot before continuing Page 16 MORE ABOUT STRAIGHT STITCHING Straight Stitching Centre Needle Position Turn the pattern selector dial so that A appears in the stitch display window Adjust the stitch length by turning the stitch length dial to the desired stitch length To get a reinforced triple straight stitch turn the stitch length dial to position S1 STITCH LENGTH DIAL _ STITCH DISPLAY WINDOW Straight Stitching Right Needle Position Turn the pattern selector dial so that B appears in the stitch display window Adjust the stitch length by turning the stitch length dial to the desired stitch length REVERSE SEWING SWITCH To get a reinforced triple straight stitch turn the stitch length dial to position S1 PATTERN SELECTOR DIAL STRAIGHT STITCHES Page 17 ZIG ZAG STITCHING Turn the pattern selector dial so that the stitch display shows C zig zag NW A Turning the pattern selector dial will increase or decrease the zig zag width STITCH LENGTH DIAL Using the stitch length dial while zig zag stitching The density of zig zag stitches increase as the setting of stitch length dial approaches 0 Neat zig zag stitches are usually achieved at settings of 2 5 or below Closed up zig zag stitches close together are referred to as a satin stitch Page 18 ADJUSTING THE UPPER THREAD TENSION Rotate the dial to adjust the upper thread tensi
17. on The basic thread tension setting is 4 To increase the tension turn the dial to the next number up To reduce the tension turn the dial to the next number down The diagram shows the effects of different thread tension settings A Normal thread tension B Upper thread tension too loose C Upper thread tension too tight Page 19 MORE ABOUT THE PRESSURE FOOT The presser foot can be raised through two levels When sewing several layers or thick fabrics the presser foot can be raised a second Stage for easy positioning of the work A Adjusting the pressure of the presser foot The presser foot pressure of the machine has ben pre set and requires no particular readjustment for different types and weights of fabric LOOSEN However if you need to adjust the presser foot pressure turn the presser adjusting screw with a coin For sewing very thin fabric loosen the pressure by turning the screw counter clockwise and for heavy fabric tighten by turning it clockwise Page 20 gt TIGHTEN MATCHING THE NEEDLE FABRIC AND THREAD NEEDLE FABRIC THREAD SELECTION GUIDE NEEDLESIZE FABRICS THREAD Lightweight fabrics thin cottons voile serge silk muslin interlocks cotton knits tricots jerseys crepes woven polyester shirt amp blouse fabrics 12 80 Medium weight fabrics cotton satin sailcloth double knits lightweight woollens Most threads sold are medium size and suitable for these
18. ough the stitch plate hole Lay both threads to the back under the presser foot 2 BASIC SEWING STITCH LENGTH DIAL Basic Machine Setting Figure 1 Set the Stitch Length Dial to 2 This provides a small medium stitch length Set the Pattern Selector Dial to display A in the Stitch Display Window This sets the needle to centre stitch position LI STITCH DISPLAY WINDOW es Raise the Presser Foot PATTERN SELECTOR DIAL l J REVERSE SEWING SWITCH Inserting the Fabric Figure 2 Lay the uper and lower threads to the rear of the presser foot Insert the fabric under the presser foot and line it up carefully Stitching the Fabric Figure 3 Switch the machine on Lower the presser foot onto the fabric N Press the foot pedal to start the machine Keeping a steady pressure on the foot pedal guide the fabric through the machine with a steady hand Page 15 REVERSE SEWING At the end of the seam Figure 1 Press down the reverse sewing lever A Sew a few reverse stitches Release the lever and the machine will sew forwards again REMOVING THE WORK Figure 2 Turn the handwheel towards you to bring the thread take up lever to its highest position raise the presser foot and remove work towards the back and side To cut the thread Figure 3 Gently pull the work away releasing a generous length of thread Place the threads over the cutting slot B and press down to cut the thread Lay the threads to the back
19. rom you Pull the buttonhole foot towards you as far as it will go Lower the foot Sewing the buttonhole 1 1 Turn the pattern selector dial to Ll Sew at moderate speed until you reach the end mark 4 2 Turn the pattern selector dial to and sew 5 6 bartack stitches 3 Now turn the selector dial to Sew the left side of the buttonhole to the mark at the end furthest from you SJ 2 gt 4 4 Turn the pattern selector dial to and sew bar tack stitches owe a a Remove the fabric from under the foot Draw the upper thread through the reverse side of the fabric and knot upper and lower threads Cut the centre of the buttonhole with the seam ripper being careful not to cut the stitches on either side i i 22N Tips Slightly reduce upper thread tension to produce better results Use backing material for fine and stretchy fabrics tis advisable to use a gimp cord for stretch or knit fabrics The zigzag should sew over the gimp 5 Page 23 ATTACHING ZIPPERS AND PIPING STITCH LENGTH DIAL ZIPPER FOOT Set the machine as illustrated Figure1 The zipper foot can be inserted right or left depending on which side of the foot you are going to sew Fig 2 To sew past the zipper pull lower the needle into the fabric raise the presser foot and push the zipper pull behind the presser foot Lower the foot and continue to sew It is also possible to sew in a length of cord into a b
20. sewing position Note When the bobbin winder spindle is in bobbin winding position the machine will not sew To start sewing push the bobbin winder spindle to the left sewing position Page 11 INSERTING THE BOBBIN fT ee When inserting or removing the bobbin the needle must be fully raised Switch the power OFF 1 Open the hinged cover 2 Hold the bobbin case with one hand Insert the bobbin so that the thread runs in a clockwise direction arrow 3 Put the thread under the tension spring 4 Hold the bobbin case by the hinged latch 5 Insert it into the shuttle Press it fully home and then release the latch CHECKING AND ADJUSTING THE BOBBIN TENSION The bobbin tension is factory preset and should not need adjusting However if the tension is not correct the thread will not feed properly To test the bobbin thread tension Remove the bobbin case and bobbin and hold it by suspending it by the thread Jerk it once or twice If the tension is correct the thread will unwind by about 25 50 mm If the tension is too tight it does not unwind at all If the tension is too loose it will drop too much To adjust turn the small screw on the side of the bobbin case Page 12 THREADING THE UPPER THREAD This operation is important to carry out correctly as by not doing so many sewing problems could result We suggest you read through the procedure carefully and carry out this process se
21. to bring up the lower thread through the fabric Sew a few securing stitches at the starting point Hold the hoop with thumb and forefingers of both hands while pressing the material with the middle and third fingers and supporting the outside of hoop with smaller finger Page 31 DARNING PLATE MONOGRAMMING AND EMBROIDERING 2 USING AN EMBROIDERY HOOP NOT SUPPLIED MONOGRAMMING 1 Sew moving the hoop slowly along the lettering at a constant speed 2 Secure with a few straight stitches at the end of the last letter EMBROIDERING 1 Stitch the outline of the design by moving the embroidery hoop 2 Fill in the design working from the outline of the design to the inside and from the inside to the edge of the outline until the design is completely filled in Keep the stitches close together A long stitch is made by moving the hoop rapidly and a short stitch is made by moving it slowly 3 Secure with a few straight stitches at the end of the design Page 32 MAINTENANCE 1 REPLACING THE LIGHT BULB Disconnect the machine from the power supply by removing the plug from the mains socket Loosen screw A as illustrated Figure 1 Remove the cover B Unscrew the bulb and fit a new one C Figure 2 Replace the cover and tighten the screw Page 33 MAINTENANCE 2 CLEANING AND LUBRICATION Disconnect the machine from the power supply by removing the plug from the mains socket Remove th
22. veral times before using the machine to familiarise yourself with the process Switch the power OFF Raise the needle to its highest point 1 Raise the presser foot to release the tension discs 2 Lift up the spool pin Place the spool of thread on the holder with the thread coming off the spool as shown For small thread spools place the small side of spool holder next to spool 3 Draw thread from spool through the upper thread guide 4 Guide the thread around the thread guide 5 pulling thread through pre tension spring as illustrated Thread the tension module by leading thread down the right channel and up the left channel 6 During this process it is helpful to hold the thread between the spool and thread guide 4 At the top of this movement pass thread from right to left through the slotted eye of the take up lever and then downwards again 7 Now pass thread behind the thin wire needle clamp guide 8 and then down to the needle which should be threaded from front to back Pull about 6 8 inches of thread to the rear beyond the needle eye Trim the thread to length with built in thread cutter 9 Page 13 Vi BRINGING UP THE LOWER THREAD Refer to Figure 1 Hold the upper thread LOOSELY with the left hand Turn the handwheel forwards to lower and then fully raise the needle Refer to Figure 2 The upper thread will catch and raise the lower thread Pull on the upper thread to bring the lower thread up thr
Download Pdf Manuals
Related Search