S2000-IK Rev.03 Instruction Manual
Contents
1. 2000 IK Rev 03 Addressable Volumetric PIR Motion Detector INSTRUCTION MANUAL GENERAL 2000 IK Revision 03 Addressable Volumetric Passive Infrared PIR Motion Detector hereinafter referred to as the detector is designed to be used indoors It detects intrusion into protected areas and sends an alarm message to the connected S2000 KDL controller via the two wire multiplex addressable polling loop The S2000 IK rev 03 supports DPLS_v2 xx protocol The detector features v A red LED to indicate detector s operability v Programming the address and communicating data with the connected S2000 KDL v A tamper switch to provide detection of unauthorized access as well as to adjust the detector The detector is intended for round the clock operation SPECIFICATIONS Input Voltage via the polling loop of an S2000 KDL Current Consumption via the loop of the S2000 KDL Pre Operation Time Detection Range Target Speed White Light Immunity Sabotage Resistant Zone Operating Temperatures Humidity Overall Dimensions H x W x D Weight STANDARD DELIVERY Find the following unpacking the S2000 IK rev 03 2000 IK rev 03 detector This Instruction Manual Two woodscrews 3 5x30 Two wall plugs 6x30 Two tapping screws 2 2x6 5 Bracket to be ordered separately Package VLNNNAN A MOUNTING LOCATION CONSIDERATIONS 8 10 VDC 0 65 mA max when indication is off 15 s max 0 3 m to 12 m 0 3 m s to 3 m s Better tha2. ODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty gives you specific legal rights and you may also have other rights which vary from country to country No increase or alteration written or verbal to this warranty is authorized B oO Li m ZAO NVP Bolid 4 Pionerskaya Str Korolev 141070 Moscow Region Russia Phone fax 7 495 775 7155 SECURITYLSYSTEMS Email info bolid ru overseas bolid com www bolid com
3. ON Summarized current consumption of all the addressable devices connected to an S2000 KDL must not exceed 65 milliamperes If for example the polling loop of the S2000 KDL comprises only S2000 IK rev 03 detectors their maximum number will be equal to 65 mA n 0 65 mA Parameters of the polling loop must correlate with parameters described in the manual of the S2000 KDL 100 pcs You can check the correctness of the mounting and the correctness of the estimated number of the detectors to be connected to the polling loop by requesting for the value of the polling loop voltage at the location of the detector by means of UProg Configuration Tool This value must be above 7 V Figure 1 shows the typical schematic of wiring the detector to the multiplex addressable polling loop of an S2000 KDL In the S2000 KDL configuration the detector s type should be specified as 5 Intrusion with Tamper Check or 7 Entrance please see S2000 KDL User s Manual 2000 KDL 2000 M 2000 IK Power Supply Figure 1 Detector s Wiring Diagram PROGRAMMING The S2000 IK rev 03 to operate properly within two wire addressable polling loop of the S2000 KDL controller it must be assigned to a unique number in the range of 1 to 127 within the loop the address which is stored in the S2000 IK rev 03 non volatile memory EEPROM An S2000 IK rev 03 is supplied with the default address of 127 This address value can be changed u
4. device with the newly assigned address shall be displayed by a network controller S2000 M or UProg Configuration Tool Mark down the assigned address on the marking field of the detector If you ve failed to assign the address wait for 3 s and repeat programming ENABLING DISABLING LED INDICATION On detector s switching on the LED indication is enabled To disable indication press the tamper switch in LLSL pattern otherwise to enable indication press the tamper switch in LLSS pattern where L stands for a long pressing longer than 0 5 s while S stands for a short pressing shorter than 0 5 s Pauses between pressings must not exceed 1 s each WALK TEST The detector having been connected to the polling loop its LED lights up indicating its start self testing procedure After self testing being completed successfully the LED switches off To check the correctness of detectors mounting walk through the detection zone several times The detector is to be armed by the relevant command issued from the network controller the S2000 console When an intrusion into the protected area is detected the detector sends an alarm to the network controller and its LED flashes triply After issuing the alarm the detector will be ready to operate in two seconds If the detector s case has been open the detector sends the network controller a tamper alarm The Tamper Restored message will be issued to the network controller in 15 seconds since c
5. fitness for a particular purpose or otherwise are limited in duration to a period of one year from the date of original purchase Any action for breach of any warranty including but not limited to any implied warranty of merchantability must be brought within 12 months from date of original purchase In no case shall seller be liable to anyone for any consequential or incidental damages for breach of this or any other warranty express or implied or upon any other basis of liability whatsoever even if the loss or damage is caused by the seller s own negligence or fault Some countries do not allow limitation on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Seller does not represent that the product may not be compromised or circumvented that the product will prevent any personal injury or property loss by burglary robbery fire or otherwise or that the product will in all cases provide adequate warning or protection Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or other events occurring without providing an alarm but it is not insurance or guarantee that such will not occur or that there will be no personal injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PR
6. losing the case DETECTION PATTERN Figure 2 S2000 IK Rev 03 Detection Pattern BOLID ONE YEAR LIMITED WARRANTY Bolid Company and its divisions and subsidiaries Seller 4 Pionerskaya Str Korolev 141070 Moscow Region Russia warrants its security equipment the product to be free from defects in materials and workmanship for one year from date of original purchase under normal use and service Seller s obligation is limited to repairing or replacing at its option free of charge for parts or labor any product proven to be defective in materials or workmanship under normal use and service Seller is not responsible for results where the product is used improperly where it is used for any application it is not intended for used under unacceptable environmental conditions and mishandled or stored under improperly Seller shall have no obligation under this warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than the Seller In case of defect contact the security professional who installed and maintains your security equipment or the Seller for product repair This one year Limited Warranty is in lieu of all other express warranties obligations or liabilities There are no express warranties which extend beyond the face hereof Any implied warranties obligations or liabilities made by seller in connection with this product including any implied warranty of merchantability or
7. n 6500 Lux Yes 30 to 500 Up to 95 at 25 non condensing 68 mm x 93mm x 41 mm max 125 gram max The detector is intended to be used indoors Considering a location to mount the detector please take into account the following 1 Do not locate the detector above heaters radiators etc or close to vent openings 2 Do not locate the detector in places where it can be exposed to direct sun rays 3 In capital facilities the detector should be mounted on a wall or in a corner 4 Within light metal structures the detector should be mounted on structural frames columns trusses rather than on a wall or a corner 5 To avoid condensation on the lens and case of the detector do not attach the detector just over the entrance opening 6 There should not be any waving things like curtains and incandescent lamps in the detection area 7 Inthe premises where the detector is to be installed for the time of protection all the windows air vents balcony doors etc must be closed all ventilators heaters air conditioners must be switched off and there should not be any birds or animals 8 Non transparent objects in the detection area such as cabinets room dividers etc as well as glass or mesh partitions obscure the detection and result in forming of dead zones through which human s moving can be not detected The recommended mounting height for the detector is 2 1 meters above the floor WIRING THE DETECTOR ATTENTI
8. sing either S2000 M console tools or PC tools such as UProg Configuration Tool In order to program the unique S2000 IK rev 03 loop address connect it to a S2000 KDL controller which is in turns connected to a network controller an S2000 M console or PC under UProg software Then send one of the following commands to the S2000 KDL controller for getting more information see the relevant User s Manual Change the Device Address Use the Change Device Address command specifying the old detector address and the new detector address as the parameters see more information in the referred Manuals The network controller will display the messages about disconnecting the device with the old address and then detecting the device with newly programmed address Mark down the assigned address on the marking field of the detector Program the Device Address If the detector address is unknown or two devices have the same address then use the Program Device Address command specifying a required address as the parameter Then remove the detector cover and ensure the LED is flashing indicating the programming mode frequent short flashes every 2 s Next press the tamper switch in LLLS pattern where L stands for long pressings between 0 5s and 2s while S stands for short pressings shorter than 0 5s pauses between pressings not exceeding 3 s each If the address has changed successfully the LED will be lit steady and a message about detecting the
Download Pdf Manuals
Related Search