User Manual: EDK 350, EPK 350, EDK 352
Contents
1. In order to simulate a wall switch PTM 21x you need to use the contact pins on top of the board For details see PTM 330 user manual Page 14 GmbH 2012 Wireless 4 Working with DolphinStudio 4 1 DolphinStudio Installation 1 Download DolphinStudio from http www enocean com en download 2 Install DolphinStudio via setup program 3 Unplug jumper on STM 330 and keep it for later usage 4 Plug STM 330 temperature sensor top of EOP 350 antenna to the left side 5 Connect EOP 350 via USB cable to PC 6 Start DolphinStudio and select COM port Attention If you have installed a previous DolphinStudio version it is recommended to uninstall older version and install latest version from website If you have already installed older FTDI USB driver it is recommended to remove previous and install latest FTDI driver by cross marking installation menu at the end of DolphinStudio Setup V1 0 October 2012 Page 15 350 EDK 352 EPK 350 User Manual 4 2 Check Firmware Version and Update Firmware Version Start DolphinStudio and ENE select EOPX Programmer tab 665 2 Select Chip information Press Retrieve button 4 Current application type and version will be shown Update Firmware 1 Program and compile your own FW oder Ju download update from EnOcean website2. Manufacturer ID for example to EnOcean GmbH Manufacturer Id 0 GmbH 6 You can change the wake up cycle but keep in mind this will heavily affect the energy budget For details see STM 31x user manual Cyclic wake up Configure the cyclic wake up behaviour This configuration will overwrite the hardware settings the D enable hardware settings select OxFFFF default 1 65534 wake up cycle times use hardware settings default Typical values for OEM products are Cyclic wake up cycle 100s wake up and check temperature value Redundant retransmission min min send interval every 7 wake up Redundant retransmission mx 14 max send interval every 14 wake up Page 18 EnOcean GmbH 2012 Wireless 7 Unplug STM 330 from EOP 350 and set jumper as before near learn button Start DolphinView Advanced 9 Connect to USB 300 or TCM 320 with DolphinSniffer as gateway 10 Press learn button STM 330 gt Learn telegram will be sent and DolphinView will automatically recognize the temperature sensor see EEP symbole in node list 11 Select EEP tab and wait for the first telegram send by the sensor after the retransmission interval gt Sensor values will be automatical interpreted and plotted into a diagram prede d Di gt Manufectarcr 0x08 iraun Functions
3. Set Profile button to interpret Equipment Profile Press rocker on I side marking on PTM 210 to send switch on telegram Press rocker on O side marking on PTM 210 to send switch off telegram Equipment Profile RORG RPS Telegram FUNC 10 02 Rocker Switch 2 Rocker 0 01 Light and Blind Control Application Style 1 Number of buttons pressed simultaneously other bit combinations are not valid button Energy Bow released V1 0 October 2012 Page 11 EDK 350 EDK 352 EPK 350 User Manual 2 5 Demonstration of PTM 215 security optional The self powered PTM 215 switch comes with implemented security feature PTM tele gram contains a rolling code to prevent copying PTM supports normal mode and secure mode In order to use the secure mode you need a transceiver firmware with encryption firmware or DolphinView gt V3 2 3 0 with DolphinSniffer gt V2 6 1 0 to evaluate and view telegrams Use EOP 350 with TCM 320 DolphinSniffer to receive secure telegrams Start DolphinView and connect TCM 320 DolphinSniffer Press two contact nibbles 1 and the energy bow 2 at the same as illustrated below gt PTM will send a learn and synchronisation telegram to the receiver Received telegram log and interpreted telegram EEP view will be shown Additional documentation is available at www enocean com en security spe
4. 3 1 ECO 200 8 PTM 330 Push Button Generator amp Radio Module The ECO 200 is an energy converter for linear motion It can be used to power the PTM 330 radio module The energy output at every actuation is sufficient to transmit 3 sub telegrams with a free field range of 300m Possible applications are miniaturized switches and sensors in building technology and industrial automation Radio telegrams will be received USB 300 and shown DolphinView Basic Attention Press spring to send telegram 330 will be shown in the node list Select node and press Set Profile button to interpret Equipment Profile Press spring to send telegram Energy Bow pressed Pull spring to send telegram Energy Bow release EEP View Node Statistics Profiles 1 basic Reload Chart time resolution 1 minute EnOcean Equipment Profile RORG 0525 RPS Telegram FUNC 0x02 Rocker Switch 2 Rocker TYPE 0801 Light and Blind Control Application Style 1 Learn Telegram Data Telegram Interpretation Rocker ist action Button AO Switch light off or Dim light up or Move blind open Energy Bow pressed Rocker 2nd action Button AI Switch light or Dim light down or Move blind closed 2nd Action No 2nd action Number of buttons pressed simultaneously other bit combinations are not valid no button
5. 18 SL HUR BND SL HUB FT2232D GNDGNDGNDGNDGNDGND GND Page 24 EnOcean GmbH 2012 Green Smart Wireless enocean 3 34 DC DC converter Itz LP2335 3 3 UIN ENABLE ui T GNO GNO m LJ Programmer interface Da e 5 2441 BR m e P P4 e nb 2 1 m 4 nb zi RxD 5 5 SCLEDIOL 5 RSOADIOS ng z gyf 11 WSOADIO2 H i OW Ta Ding 2 21 E 18 ADO 28 ia D BD GHO SUS V1 0 October 2012 Page 25 EDK 350 EDK 352 EPK 350 User Manual EXT PINS 1 ACTUATOR zz 502 te Hbi a SED H PEDIR HgO LDDL 18141 GATEWAY R35 06 Ln GHOGHO BUTTONS R36 UCCIOINT ent Bin too 2 SKOA RESET lU HODE1 JPL R25 162 GHOGHO Page 26 212 1 0 LABORATORY USE ONLY n ANTENNA t T DOOR SS IE 8 Gu 2 u dq au m GATEWAY 2 ACT i LMI m io 0 og Bug 808 808 504 p EEG gt 5 5 5 EOP350 2 October 2012 en 0 PROG Wireless 125
6. Rule for Enforcement of Radio Law of Japan Use this kit only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this product or use of this product only after you obtained the technical regulations conformity certification as provided in radio law of Japan with respect to this product Do not transfer this product unless you give the same notice above to the transferee Please note that if you could not follow the instructions above you will be subject to penalties of Radio Law of Japan Wireless 1 Introduction UM RM M UEM NU NNNM MERE NUS 4 1 1 Overview EnOcean Developer EDK 350 0 0102222222 2 4 1 1 Developer Kit EDK 5 1 2 EnOcean Thermo Developer EDK 352 2 2 2 2 4 2 2 4 6 1 3 Programmer Kit EPK 350 audiui 7 2 First Steps and 8 2 1 Demonstration of 1 Channel Relay Switch and Learn Concept 8 2 7 SoftWare Installation gt 9 2 3 DolphinView __________ 10 2 4 Demonstration of 210 PTM 21
7. 0 10 Room Operating Pane Tyne Teeparstirs Sanear Set Point wed Onnan Contro Set Point 4 00 antl mac s ta noue 1127 13 19 20 A Tempasturs 21 85 C ntl Device A amp FE 4 ues j V1 0 October 2012 Page 19 350 EDK 352 EPK 350 User Manual 5 Write your own Firmware Download DolphinAPI and install from http www enocean com en download Get your IDE Keil uVision and C51 develop ment tool PK51 from ARM http www keil com c51 pk51kit as A description and C cod samples of DolphinAPI can be found within the installation folder Implement your application and upload the firmware via DolphinStudio If you have any questions please contact our application engineering Support enocean com Page 20 radio ULP mod Application gallcg 59 35 e n u J 48 3 58 3 2 Flash Memory 32k TX State Engine PWM Timer SPI UART Voltage Regulator Mixed Signal Sensor Interface 16 I Os 16V EnOcean GmbH 2012 Green Smart Wireless 6 Usage of EDK 352 Thermo Developer Kit optional Introduction EDK 352 extends the basic developer kit EDK 350 with a thermo powered radio module solution Energy is converted from the heat flux through the Peltier element EnOcean s ultra low
8. MD RW ER RIEN RM REDE M 24 V1 0 October 2012 Page 3 350 EDK 352 EPK 350 User Manual 1 Introduction 1 1 Overview EDK 350 Thermo Dev Kit extend your developer kit or programmer kit with a thermo harvester powered sensor platform EPK 350 Programmer Kit EDK 350 Developer Kit upgrade your starter kit to the everything you need to start full blown developer kit implementing innovative self powered solutions demonstrate configure hardware design and software programming ESK 300 Starter Kit the easy way to get started with battery less technology 4 EnOcean GmbH 2012 FA Wireless enocean EnOcean Developer Kit EDK 350 EDK 350 contains everything you need to start implementing innovative solutions with EnOcean s energy harvesting and ultra low power radio technologies The kit will help you to demonstrate and configure EnOcean products Additionally you can easily design new hardware and start software programming Content User Manual USB 300 USB Stick Gateway PTM 210 Push button switch or PTM 215 Switch with security Rocker amp housing example STM 330 Self powered temp sensor ECO 200 Mechanical energy harvester PTM 330 Push button radio module TCM 320 Transceiver module STM 300 Radio sensor module EOP 350 Universal programmer board Updates for this user manual are available at http www enocean com en
9. Oct 10000 RSDADIO3 45040102 SCLKDIO4 SCSEDIO PROG_EN yoo yoo JDDLIM RESET WAKE4 27 EnOcean is the originator of patented energy harvesting wireless sensor technology The company manufactures and markets maintenance free wireless sensor solutions for use in buildings and industrial installations EnOcean solutions are based on miniaturized energy converters ultra lowpower electronic circuitry and reliable wireless Combining these elements enables EnOcean and its product partners to offer sensor systems that are fundamental for energy efficient buildings and innovative industry www enocean com Our value added distributors provide customers gt with applications support and technical expertise SA ocean www enocean com distributor SET UP ON THE ENOCEAN STANDARD FOR ENERGY HARVESTING WIRELESS SENSOR SOLUTIONS
10. enocean modules edk 350 V1 0 October 2012 Page 5 350 EDK 352 EPK 350 User Manual 1 2 Thermo Developer Kit EDK 352 EDK 352 extends the EnOcean Developer Kit EDK 350 with a thermo harvester powered radio sensor platform Content User Manual STM 312 Universal radio sensor module ECT 310 Ultra Low Voltage Converter Peltier element Updates for this user manual are available at http www enocean com en enocean modules edk 352 Page 6 EnOcean GmbH 2012 Green Smart Wireless 1 3 350 The programmer EPK 350 is an upgrade for the starter kit ESK 300 to the the features set of the developer kit EDK 350 Content User Manual TCM 320 Transceiver module STM 300 Radio sensor module EOP 350 Universal programmer board Updates for this user manual are available at http www enocean com en enocean modules epk 350 V1 0 October 2012 Page 7 EDK 350 EDK 352 EPK 350 User Manual 2 First Steps and Demonstrations 2 1 Demonstration of 1 Channel Relay Switch and Learn Concept The TCM 320 module has already several pre implemented features for building automa tion The 1 relay mode is used to switch on and of a module pin If you connect a relay to this pin you can switch mains powered device 1 Plug TCM 320 into EOP 350 and set jumper to 1 CH ACT ui 2 C
11. voltage converter converts tiny voltage 20mV from the Peltier element to operate the STM 312 sensor module Content EDK 352 User Manual STM 312 generic sensor platform ECT 310 ultra low voltage DC DC converter Peltier element V1 0 October 2012 Page 21 EDK 350 EDK 352 EPK 350 User Manual 6 1 Connect STM 312 with ECT 310 and Peltier element Solder output pins of the ultra low voltage converter ECT 310 to the power input pads on the backside of STM 312 sensor Peltier element to the input pins of ECT 310 For details and pin layouts see STM 31x user manual 6 2 Demonstration Expose the Peltier element to a heat flux of more than 1 2 C temperature difference between cold and hot side With an ambient temperature of about 20 C it is enough to hold the finger on top of the hot side of the Peltier element This causes enough energy to power STM 312 and send several telegrams In order to generate a permanent heat flux we recommend to use heat spreader on the cold side and a hot surface e g heating system hot en gine etc on the hot side For details of external sensor pins see STM 31x user manual Page 22 EnOcean GmbH 2012 Green Smart Wireless 7 References USB 300 http www enocean com en enocean modules usb 300 oem 210 http www enocean com en enocean modules ptm 210 PTM 215 http www enocean com en enocean module
12. 5 standard mode 11 2 5 Demonstration of 215 security optional 2 2 2 2 22 2 12 3 Assembling of an Industrial Switch 13 3 1 200 amp 330 Push Button Generator amp Radio 14 4 Working with Dolphin Studio NUFEERE E MEE ERR ENUFER ERR EE TEFRF KNEE REN EE EE REN NM EE 15 ases conia cunei S __ __________ d Ra Pn 15 4 2 Check Firmware Version and Update 2 2 2 2 7 16 4 3 Configuration of Temperature Sensor STM 330 2 17 5 Write your own Firmware 20 6 Usage of EDK 352 Thermo Developer Kit optional eese eere 21 6 1 Connect STM 312 with ECT 310 and Peltier 22 6 2 Demonstration C Bm 22 7 References 2 2 2 23 8 EOP 350 2 Circuit amp LayOUEL uisssexss cus un S EE EDE ERU NK EUR EU
13. T 19 2 in 5 O 5 o np Y O Ou 2 COMPE a O 5 199 LA LA EDK 350 Developer EDK 350 EDK 352 350 Important Notes This information describes the type of component and shall not be considered as assured characteristics No responsibility is assumed for possible omissions or inaccuracies Circuitry and specifications are subject to change without notice For the latest product specifications refer to the EnOcean website http www enocean com As far as patents or other rights of third parties are concerned liability is only assumed for modules not for the described applications processes and circuits EnOcean does not assume responsibility for use of modules described and limits its liability to the replacement of modules determined to be defective due to workmanship Devices or systems containing RF components must meet the essential requirements of the local legal authorities The modules must not be used in any relation with equipment that sup ports directly or indirectly human health or life or with applications that can result in danger for peo ple animals or real value Components of the modules are considered and should be disposed of as hazardous waste Local government regulations are to be observed Packing Please use the recycling operators known to you By agreemen
14. cification and http www enocean com en enocean modules ptm 215 Export Profiles 2 5 Chart time resolution 1 minute 0 Equipment Profile RORG 0834 SECD Decrypted Secure Telegram FUNC 0802 Rocker Switch 2 Rocker TYPE 1001 Light and Blind Control Vie F rao p serai 09 Logdiepdenycus 194 0 Port Data Status Ace 09 46 04 396 FEFFFEFO SEC TI 25 48 ES 68 FO 17 59 09 COMIS 09 46 04 064 FEFFFEFO 1 SE 48 D ES D 43 00 09 46 08 115 FEFFFEF 09 oF 09 09 09 46 08 356 SECD 09 46 09 269 FEFFFEF SECD 2 12 EnOcean GmbH 2012 Green Smart Wireless 3 Assembling of an Industrial Switch Just combine the plastic frame switch with mechanical energy harvester ECO 200 and radio electronic board PTM 330 and you have assembled your first self powered switch This demonstrates how EnOcean s energy harvesting and ultra low power radio technol ogy can be implemented within various environments 1 Place ECO 200 generator into plastic frame 2 Clip PTM 330 electronic board on top f Er E 3 Press the spring on the ECO 200 and it will send multiple EnOcean telegrams V1 0 October 2012 Page 13 EDK 350 EDK 352 EPK 350 User Manual
15. e g i o http www enocean com en download _ 2 Start DolphinStudio and ___ select EOPX Programmer tab p Select Programmer 4 Select FW file via Browse button chip configuration file will be automatically recognized by ending cfg hex 5 Press Execute button to start the update process o Page 16 EnOcean GmbH 2012 4 3 1 2 3 4 V1 0 Configuration of Temperature Sensor STM 330 Select Configuration tab within DolphinStudio Select STM 33x within configuration window Click on read configuration button 030001 Configuration EOPX Programmer Modul Configuration Programmer Configuration ea Modul Information Modul Configuration EnOcean Equipment Profile Teach In telegram You will get on overview of the temperature sensor pre defined configuration EnOcean Equipment Profile Teach In telegram Select EnOcean Equipment Profile EEP The EEP information is used in teach in telegram Select Manufa System Log Reserved to disable teach in telegrams NOTE In order to use Humidity Sensor profiles a HSM 100 module has to be plugged in Profile A5 02 05 Temperature 0 to 40 Manufacturer October 2012 Page 17 EDK 350 EDK 352 EPK 350 User Manual 5 STM 330 will only send a LEARN telegram if an Manufacturer ID is configured Change
16. ode for switching dimming etc Comprehensive software libraries wireless communication energy management V1 0 October 2012 Page 9 350 EDK 352 EPK 350 User Manual 2 3 DolphinView Advanced EnOcean DolphinView visualizes and interprets EnOcean radio telegrams It receives EnOcean telegrams via USB 300 or TCM 320 with DolphinSniffer Software PTM i Radio based EnOcean DolphinView 210 215 USB Serial 300 S Se on EnOcean Alliance Protocol Version 3 STM Equipment Profile 330 2 2 ISO IEC 14543 3 10 330 Download DolphinView from EnOcean s Software download website Execute the DolphinView setup program and follow instructions Connect the USB 300 to your PC or notebook Execute DolphinView and press the connect button Page 10 EnOcean GmbH 2012 FA Wireless 2 4 Demonstration of 210 215 standard mode The push button radio transmitter module enables the implementation of wireless remote controls without batteries Key applications are wall mounted flat rocker switches with 1 or 2 rockers as well as handheld remote controls with up to 4 single push buttons Radio telegrams will be received via USB 300 and shown by DolphinView Press rocker to send switch telegram gt 210 will be shown in node list Double click on PTM within the node list 3 PTM will be added to the node list Select node and press
17. onnect EOP 350 with USB power e g PC 3 Learn PTM 210 215 switch ID to TCM 320 Press LEARN button on EOP 350 gt 0 55 gt LMI LED will light CHO will flash Push switch rocker one time to send learn telegram Finish learn mode with LEARN button gt 0 55 4 Push PTM 21x rocker will toggle CHO LED relay pin Attention This example works only with TCM 300 320 standard firmware If you have changed TCM firmware e g DolphinSniffer load TCM 320 default firmware from website If you push the switch a second time during learn mode this will delete the learned ID Page 8 EnOcean GmbH 2012 FA Wireless 2 2 Software Installation Please register your personal account on the EnOcean website http www enocean com en download Following software components need to be downloaded and installed DolphinView Visualize properties of EnOcean radio nodes Receives sends and analyses radio telegrams according to the EnOcean standard Get detailed information e g sub telegram timing and signal strength Content of telegrams can be analyzed online and logged with time stamp Supports remote management features like ping query and remote learn DolphinStudio DolphinStudio software provides a graphical user interface allowing easy configuration and programming of EnOcean modules with Dolphin chip DolphinAPI Operating system for self powered applications Source code samples in C C
18. s ptm 215 STM 330 http www enocean com en enocean modules stm 330 ECO 200 http www enocean com en enocean modules eco 200 PTM 330 http www enocean com en enocean modules ptm 330 Software can be found at www enocean com download Additional information http www enocean com knowledge base Technical support support enocean com EnOcean radio physical data link and network layer ISO IEC 14543 3 10 Information Technology Home Electronic Systems http www iso org iso catalogue detail htm csnumber 59865 EnOcean Alliance application layer EnOcean Equipment Profiles http www enocean alliance org en home EnOcean security specification WWw enocean com en security specification V1 0 October 2012 Page 23 350 EDK 352 EPK 350 User Manual 8 EOP 350 2 Circuit amp Layout USB serial converter UB RSTOUT PHREN H 2 CLKDIO USBDP USBDH pxDa api 23 RTSA AD2 UD XTIN 5 UR PROGLED OSPA ADS 12 2 50 XTDUT PIR RD 4 YDENA 6 15 6 egi 80107 A ACL x gt EEDRTR TXLED RC3 X XD auc ta Bx 46 auec RTSB BD2 38 R4 RESET ucc CTSB BD3 ES UCE 26 220 UCCIOR 5 22 ada C14 0 08 806 aj 1 22nF L RIB BD N 3l 3U30UT n amp TEST TXDENB BCO pm SLEEPB BCi 29 GNDGND GNDGND NI AGND PxLEDB BC2 GND TXLEDB BC3 2
19. t we will take packing material back if it is sorted You must bear the costs of transport For packing material that is returned to us unsorted or that we are not obliged to accept we shall have to invoice you for any costs incurred This development kit and its components are intended for use for evaluation demonstration or engineering development purposes only It is not considered to be a finished end product fit for consumer use Persons handling this developer kit must have electronics expertise and observe good engineering practice standards As such the goods being provided are not intended to be complete in terms of required design marketing and or manufacturing related protective considerations including product safety and environmental measures typically found in end products that incorporate such electronic components or circuit board EnOcean does not reliable consequences for any HW or SW changes modifications of the developer board done by the developer Important notice for users in Japan This developer kit is not certified as confirming to technical regulations of radio law of Japan If you use this kit in Japan you are required by Radio Law of Japan to follow the instructions below with respect to this product Use this product in a shielded room or any other test facility as defined in the notification 173 issued by Ministry of Internal Affairs and Communi cations on March 28 2006 based on sub section 1 1 of article 6 of the
Download Pdf Manuals
Related Search