Home

T230 MOTORIZED VIP 3K OPERATION and MAINTENANCE

1. T230 MOTORIZED VIP 3K OPERATION and MAINTENANCE MANUAL TABLE OF CONTENTS BEFORE YOU START 3 TURNSTILE SAFETY INSTRUCTIONS 3 TURNSTILE USER INSTRUCTIONS 3 T230 MOTORIZED VIP 3KTURNSTILE TECHNICAL SPECIFICATIONS 4 T230 MOTORIZED VIP 3KTURNSTILE SYSTEM SPECIFICATIONS 5 POWER SUPPLY 5 T230 MOTORIZED VIP 3KTURNSTILE ASSEMBLY INSTRUCTIONS 1 6 T230 MOTORIZED VIP 3KTURNSTILE MATERIAL LIST 7 T230 MOTORIZED VIP 3KTURNSTILE ELECTRICAL CIRCUIT DIAGRAM 8 T230 MOTORIZED VIP 3KTURNSTILE HOW TO RUN 9 T230 MOTORIZED VIP 3KTURNSTILE MAINTENANCE INSTRUCTIONS 11 T230 3K TURNSTILE TROUBLESHOOTING 12 BEFORE YOU START Thank you for purchasing T230 Motorized Vip 3K Turnstile Please carefully read the instructions contained in this manual for a long and smooth operation of the turnstile and keep the manual for future references TURNSTILE SAFETY INSTRUCTIONS It is recommended to read all safety and maintenance instructions before installing and using the turnstile e Read the manual before operating the turnstile Do not open the turnstile due to safety precautions Any repairment must be done only Py authorized services Modifications made by user may result in danger or the turnstile and people e Do not operate damaged turnstiles and call an authorized service immediately e Comply with the power and voltage values specified in the technical specifications of turnstile e Comply with the operati
2. EMO AUX SUPPLY OUT 18 Vis GC ef connected to GEMO 121 INHIBIT Microswitch layout AG red led SETS Fa CH CO green led black m L_A2 D R vi E In12 I CH Buzzer Jor msi el A wie nl S 99 In10 z A Ing P CH mfrenjon JER KER RI ng Te ie KS e y A IL A InG o Y K m Ar 0247 E woo gt D KN re lt ETAT JE O Del Supply In Y kullarul miyor llan lm yor k_1 Binz e llan lm yor Input_2 llan lm Buzer fullanlmi yor A NIZI polo el on H sensori XA See E pink i H sensor L KUMANDA T230 MOTORIZED VIP 3KTURNSTILE HOW TO RUN A THE CONTROL IS STARTED IN 3 SEC AFTER POWER CUT IF THE ARM IS IN ZERO MODE CLOSED MODE IT IS LOCKED AT THIS POSITION IF THE ARM IS BETWEEN OPEN amp CLOSED POSITION IT MOVES IN CCW DIRECTION IF THE ARM COMES TO THE CLOSED MODE IT STOPS amp LOCKS IF THE ARM IS OPEN IN CCW DIRECTION IT STOPS AND CLOSES AFTER 5 SEC NOTE IF IT IS INHIBITED IN CCW DIRECTION IN SETUP ZERO MODE DIRECTION IS CW B THE BUTTONS ON THE REMOTE CONTROL 1 CCW COUNTER CLOCKWISE BUTTON IT IS FOR MOVING THE ARM IN ANTI CLOCKWISE DIRECTION IF THE ARM IS CLOSED IT OPENS IN CCW DIRECTION IF CW IS OPEN THE ARM IS CLOSED 2 CW CLOCKWISE BUTTON IT
3. IS FOR MOVING THE ARM IN CLOCKWISE DIRECTION IF THE ARM IS CLOSED IT OPENS IN CW DIRECTION IF CCW IS OPEN THE ARM IS CLOSED NOTE IF THE BUTTON IS PRESSED DURING OR AFTER THE ARM IS OPENED THE ARM REMAINS OPEN IN ORDER TO CLOSE THE ARM PRESS THE OTHER BUTTON IF THE ARM IS OPEN AND NOT IN IDLE MODE IT IS CLOSED AFTER 5 SEC TIME CAN BE CALIBRATED IN SETUP 3 IDLE CONTROLLED BUTTON WHEN PRESSED THE ARM IS IDLE AND IT CAN BE MOVED BY HAND WHEN THE BUTTON IS IN NORMAL POSITION THE EQUIPMENT IS CONTROLLABLE C USING SENSOR WHILE OPENING IF THE SENSOR DETECTS A PERSON THE ARM IS OPENED AFTER PRESSING THE OPEN ARM BUTTON D RED READY GREEN ON WARNING LIGHT AS OPENING GREEN BLINKS WHEN OPENED GREEN IS ON AS THE ARM IS CLOSING RED BLINKS WHEN CLOSED RED IS ON 11 Opening in CCW direction Closing in CCW direction fe i i gt Ne Open in CCW direction e 12 T230 MOTORIZED VIP 3KTURNSTILE MAINTENANCE INSTRUCTIONS 1 The clothing of the turnstile must be cleaned with wet rag 2 The connection screws of turnstile should be visually checked every 6 months 3 Turnstile arm connection must be visually checked NOTE Turnstile must have maintenance service by authorized service or distributors periodically In case it is not able to contact with an authorized service or dealer get into contact with producer firm and obtain information on periodical maintenance Turnstile Pl
4. Y INSTRUCTIONS Select a proper location so as not to obstruct turnstile s operation Check the structure of the ground of installation site to ensure the necessary stability reguirements Mark the hole places on the ground in which the turnstile will be mounted Drill the marked mounting holes by 310 drill bit and clean the dust inside the hole by the help of the air Fix the steel anchors to the drilled holes If the ground is not strong fix the steel anchors after using chemical soil mixture Wait 20 minutes for hardening of chemical soil mixture Pass the power and data cables which are prepared before through the hole on mounting plate Put the mounting plate on the steel anchors and after putting the washer and nuts fix the ground You can see the pictures and drawing illustrating anchor and turnstile s mounting operation HOLE FOR CABLES T230 MOTORIZED VIP 3K MATERIAL LIST A B C D E M6x10 M8x25 M8 M8 M8 STEEL INBUS RONDELA NUT WASHER ANCHOR BOLT 4 pieces 4 pieces 4 pieces 4 pieces 4 pieces T230 MOTORIZED VIP 3KTURNSTILE ELECTRICAL CIRCUIT DIAGRAM Ifyou want it not to open anti clockwise the wire connected to meet po pee GEMO AUX SUPPLY OUT 18 V is AUC Set U fo O 2 kid D o connected to GEMO 12 INHIBIT CW ua i in entry If you want it not to open clockwise the wire connected to 2 G
5. and smooth manner with the aid of electronic gear and smart control unit 4 Every turnstile is designed with a control card however it can be modified and programmed for customer needs and wants optional 5 Turnstiles switch to home mode in 15 sec if there is no pass after the entry data is received the locking time can be calibrated if needed as optional 6 The turnstile is switched to the emergency mode by the manual button or any data coming from the fire alarm system In emergency the system is shut down and turnstiles provide free passing in both directions 7 Turnstiles allow only one pass based on the Access type token card reader button etc 8 Entry data is transferred to terminal after the necessary system infrastructure POWER SUPPLY 1 Do not remove the protecting seal on the power supply 2 Please perform your operations paying attention to the warnings electricity and safety fuse data on the protecting seal and power supply 3 On the label placed on the power supply the connection points are shown Please follow the signs on the label while carrying out the connection NOTE PLEASE DO NOT PROVIDE THE POWER FROM THE CARD OR POWER SUPPLY ON THE TURNSTILE TO THE EXTERNAL EQUIPMENT THE MANUFACTURER WILL NOT ACCEPT ANY RESPONSIBILITY FOR ANY INQUIRY OR DAMAGE RESULTING FROM INCOMPLIANCE WITH THE SECURITY AND SAFETY INSTRUCTIONS INDICATED ABOVE T230 MOTORIZED VIP 3KTURNSTILE ASSEMBL
6. eplace after pass could be broken or there may microswitches and be connection defects check the connections 2 Check the cables 2 There may be defects in the carrying data cable transferring data 3 Replace electronic card 3 Electronic card could be broken Turnstile arms are giving noise due The main mechanism may have Tighten the nut If that to friction while turning been hit and or the nut could is not the case replace be loosened up the entire mechanism The entry and exit speeds are The turnstile may not be The turnstile should be different mounted in a level ground mounted on a level ground and this operation should be checked by water balance The turnstile is not standing at 90 Switch positions may be tilted 1 Calibrate the switch degrees and it is exceeding the due to hit or switches could be positions level broken due to hits 2 Replace the switches 14 Notes 15
7. exi Bolts 1 Control months Ground Fixing Bolts 1 Control months 1 1 2 2 urnstile Mechanism Solenoids 2 Control months Cleaning Wheel 2 Control months Cleaning 2 2 Carrier Shaft Nut 1 Control months Gear Connection Bolts 1 Control months Microswitches 12 Control months Carrying mechanism 12 Control months Lubrication Electronic Card Electrical Connections 12 Control months Motor Connection Cables 12 Control months PL 12 Control months 13 T230 TURNSTILE TROUBLESHOOTING Fault Reason s Solution s Although the electricity is on the 1 Power supply may be off or ie Ghoclowhetherthe arms cannot be locked the broken displays are turned off and the electrical cable is turnstile is functionless 2 Electrical fuse could be plugged in blown out 2 Change power supply if needed After one pass the turnstile is not 1 Direction sensor locked and it allows multiple microswitches could be broken passes 2 Electronic card could be microswitches broken i 3 Magnetic gear could be 2 Replace electronic broken card 3 Check the magnetic gear connections and replace if broken Although the electricity is on the 1 Solenoid could be broken or 1 Replace arms are turning freely there may be connection solenoid and also defects check the 2 Electronic card could be connections broken 2 Replace electronic card The turnstile does not send info 1 Cycle sensor micro switches 1 R
8. fety instructions indicated above T230 MOTORIZED VIP 3KTURNSTILE TECHNICAL SPECIFICATIONS 500 mm 230 mm 230 mm to 990 mm 990 mm Power 220V 50Hz 30 W Operating Voltage 24 V DC 20 Body Features Waterproof body with 1 5 mm 304 grade stainless steel Control System It is commanded by Dry Contact or any other recommended voltage It is possible to use with all kinds of access control units or token mechanisms Additionally it can be commanded by RS232 and RS485 optional Pass Block By using 15 mm transparent plexiglass with separator Locking It is locked by 24DC solenoid with special magnetic gear mechanism locks when the solenoids are pulled In emergency the system is shut down and turnstiles provide free passing in both directions Motion Control Bidirectional entry exit free control Arms 14mm and made up of plexiglass Operating Temp 10C 50C Passing Signs Red light while the plexiglass is closed and green light while it is open optional Dimensions 230 x 1030 x 990 mm Weight 35 kg Accessories Electrical control unit Remote unit Button unit Modular Platform T230 MOTORIZED VIP 3KTURNSTILE SYSTEM SPECIFICATIONS 1 The system is designed to allow free pass When the power is turned off the arm turns freely 2 The parts of the turnstile carrying load and giving motion are made up of stainless steel or galvanized materials 3 The pass is performed in a silent
9. ng temperature range specified in the technical specifications of turnstile e Check the power supply and control the card connections before re energizing the turnstile afterwards any maintenance or damage e Use certificated spare parts and accessories approved and allowed by the producer e In any problem cut off the electrical connections of the turnstile and call an authorized service e During the cleaning and maintenance cut off the electrical connections Otherwise damage to the parts may result e Use wet rag for cleaning e Keep the turnstile away from over heated or fire environment Over heat may result in a damage to the turnstile Do not use the turnstile in high magnetic areas e Do not expose the turnstile to excessive water in order to prevent any penetration e Provide your turnstile with electrical grounding connection TURNSTILE USER INSTRUCTIONS e The turnstile is designed so as to allow one person to pass each time and more than one person mustn t try to pass at the same time In case of not functioning properly avoid actions that may result in damage to the turnstile In case of any malfunctioning in order to avoid further damage to the system should the system be taken in idle state or mustn t be used e Substances harmful to turnstile mustn t be used for cleaning The manufacturer will not ar any responsibility for any inquiry or damage ulm from incompliance with the security and sa

T230 MOTORIZED VIP 3K OPERATION and MAINTENANCE

Contents

Download Pdf Manuals

Related Search

Related Contents