User Manual
Contents
1. stall the sensors to an It s necessary to avoid unstable surface Don t install the sensors in the sunlight of sunrise and sunset area where there are seasonal trees growing re ew n position should be Don t install the sensors near It s necessary to test the system suitable for alignment vertical corrosive Don t soak it in water after installation f horizontal 90 x v x v Multiple sets of the photobeam sensors can be used for longer distance guard Refer to the above figures to avoid mutual disturbances When two sets of photobeam sensors are used in the same side J1 should be short circuited for one of the two sets Remove the front cover and turn on the power switch the LED indicator of the transmitter flashes 3 times The receiver s LED indicator flashes 3 times and the buzzer beeps di didi Install the view finder as shown above and push it to the end Observe at a 45 angle Make the photo of transmitter receiver in the center of the view finder by vertical and horizontal adjustment First adjust the transmitter then adjust the receiver the Vericaladi serew beep sound di di di will be heard when LO alignment is successful Put the test paper up e before the receiver and repeat alignment until the beep sound di di di can be heard again Align vertical screw to desire position After successful alignme2. SWPB 50 SWPB 100 SWPB 250 SWPB 400 FEATURES Installation amp Operating Manual Solar Powered Wireless Photobeam Sensors 50ft 100ft 250ft 400ft OKINA Create a Virtual Wall with the photobeam sensors KINAS e Detection Range 50ft 100ft 250ft 400ft depending on model e Power Consumption 200uA fully charged sensors can operate more than 30 days without sunlight e Frequency 315MHz e RF Range 2000ft 600m open area e Response Time 50ms Copyright 2012 All Rights Reserved Powered by SEN TRATO S 61 S 62 S 63 S 64 R201205 v08 A Please read the Manual before attempting to use this product RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT OPEN COVERS OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Disposal of Old Electrical amp Electronic Equipment Applicable in the European MEE Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inapp
3. U Brackets e Four 4 U Bracket Screws e Two 2 Jumpers e Two 2 View Finders e One 1 Test Paper e One 1 User Manual For any returns please include all components listed above with original packaging in Resalable Condition Absolutely No Returns will be accepted if any component is missing damaged DIMENSIONS e 8 l g Units mm PARTS amp FUNCTIONS 5a ge pe oun 5 PP Np Front Cover Optics Lens Tamper Switch J1 Jumper Local Solar Panel b Local Solar Panel Connector Power Switch BAT Test Key LED Indicator Vertical Adjustment Screw 10 11 12 13 14 15 16 POLE Main frame Buzzer for Receiver only View Finder Metal Mounting Plate Metal Mounting Plate Screw U Clamp Bracket U Clamp Bracket Screws 17a External Solar Cell Charger 17b External Solar Cell Charger Connector APPLICATION DIAGRAM Tagen SE pem 6 jtara aq a ee Pa ce Recover Transrnitior tenia A T Turn your PTZ Camera into a Smart Tracking PTZ Pr Caner er ra es teens Bites ee Floorplan Diagram Application for 3 Solar Wireless Photobeam Devices Zone 2 Dew to Alarm np gt Set te reset 2 NOTE A S24 Buma is Recomended because slows the vehicle s sped pe PEE seme enough Um to focan cn te cone late or lhere JS POSITIONS NOT SUITABLE FOR INSTALLATION Don t
4. ator cover charging is quickly does not flash and buzzer does not beep when power is on Detection range is not 1 Alignment is not 1 Confirm proper installation of the enough optimum viewfinder and optimize alignment 2 Stored power is low with the test paper 2 This problem can be fixed after sitting out in direct sunlight False Alarm 1 The base was not 1 Select a firm installation base strong installed properly enough to withstand wind 2 Alignment is not 2 Optimize alignment with the test optimum paper 3 Batter power is low 3 Let photobeam sit out in direct 4 Front covers are sunlight to recharge polluted 4 Clean the front covers 5 There is some moving 5 Clear away any object blocking object between the photobeams transmitter and receiver Alarm Failure 1 The signal of the 1 Because of the reflection do not transmitter is reflected select long distance model for indoor to the receiver use Change the installation positions 2 Other transmitter s of the transmitter to avoid reflection signal are interfering 2 Change the other transmitter s with the receiver installation position 3 Battery power is low 3 Let photobeam sit out in direct sunlight to recharge 10 SPECIFICATIONS Model SWPB 50 SWPB 100 SWPB 250 SWPB 400 Detection Range Soft 100ft 250ft 400ft Detection Rahe Twin beam infrared pulse alarm only when all beams are broken Resp
5. less VS MCR 304 Receiver VS MCR 308 t 12
6. nt remove the view finder and then install the front cover Remove the View Finder P horizontal adjustment vertical adjustment a 180 90 10 CS INSTALLATION Note Due to various pole sizes the installation instruction below is recommended for poles with a diameter of about 1 18 30mm Visit your local hardware store if additional materials are required for mounting the photobeam sensors on a larger sized pole A Pole Mounting 1 Pull the two bottom corners of the front cover outward and remove the front cover 2 Fix the metal mounting plate and U Clamp bracket with screws 3 Screw the mainframe to the metal mounting plate 4 Place the cover back over the mainframe B Wall Mounting 1 Pull the two bottom corners of the front cover outward and remove the front cover 2 Fix the metal mounting plate to a wall with screws 3 Screw the mainframe to the metal mounting plate 4 Place the cover back over the mainframe Wall Mounting Sorew Holes TROUBLESHOOTING Trouble Reason Solution Transmitter LED The energy stored isnot Press BAT TEST key to check if there indicator does not enough to support the is enough stored energy IF LED is not flash when power is system on lighted put it under the sunlight and on check it next day Without the front Receiver LED indic
7. onse Time 50ms Power Input Solar energy Power Consumption 200UA the full charged system can work continuously more than 30 days without sunlight LED Indicator 1 Flash 3 times when power on 2 LED on in alarm condition Receiver only 3 __ Flash 1 9 times when alignment is successful receiver only Buzzer Receiver only 1 Beep dididi when power on 2 Beep di di when alignment is successful then stop beeping 3 __ Beep di per 10 seconds when alignment is not successful Alarm Output Wireless RF Transmission to Wireless Receiver SWPBR Frequency 315MHz RF Range 2000ft 600m open area Tamper Switch Valid Vertical 10 5 degrees Alignment Angel Horizontal 180 90 degrees Mounting Wall Mounting or Pole Mounting ARGIS 13 F 131 F 25 C 55 C Dimension 2 874 x 3 3465 x 7 0866 73mm x 8mm x 180mm Weight 1 4 Ibs Specifications are subject to change without notice 11 LIMITED WARRANTY LIMITED ONE 1 YEAR WARRANTY AND EXCLUSIONS Manufacturer warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Manufacturer is free of defects in materials and workmanship under normal and proper use for one 1 year from the purchase date Manufacturer s only obligation is to correct such defects by repair or replacement at its option if within s
8. ropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product CAUTION 1 Handle this product with care Avoid any shock or bumping of the product Improper handling could damage the product 2 Requires a proper operating environment This product is designed for outdoor use The allowable temperature range for operation of this product is between 13 F 131 F 25 C 55 C 3 Check the power source voltage The power source voltage should be within the specified range Product must meet the specifications 4 Objects and liquid entry Never push objects of any kind into this product as this may touch dangerous voltage points of short out parts that could result in a fire or electric shock Never spill any kind of liquid on the product 5 Servicing Do not attempt to service this product by yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all service to qualified servicing personnel 7 Retain Instructions The safety and operating instructions should be retained for future reference PACKAGE COMPONENTS One 1 Photobeam Transceiver e One 1 Photobeam Receiver e Two 2 Metal Mounting Plates e Two 2 Metal Mounting Plate Screws e Two 2 Pole Mounting
9. uch one 1 year period the product is returned prepaid with proof of purchase date and a description of the problem This warrant excludes and there is disclaimed liability for labor for removal of this product or reinstallation This warranty is voided if this product is installed improperly or in an improper environment overloaded misused opened abused or altered in any manner or is not used under normal operating conditions or not in accordance with any labels or instructions There are no other implied warranties of any kind including merchantability and fitness or a particular purpose but if any implied warranty is required by the applicable jurisdiction the duration of any such implied warrant including merchantability and fitness of or a particular purpose is limited to one 1 year Manufacturer is not liable for incidental indirect special or consequential damages including without limitation damage to or loss of use of any equipment loss sales or profits or delay or failure to perform this warranty obligation The remedies provided therein are the exclusive remedies under this warranty whether based on contract tort or otherwise RELATED ACCESSORIES Solar Powered Wireless Signal Repeater Solar Powered Wireless Siren SWPREPT SWSIREN 1 Zone Non Supervised External Solar Cell Charger Wireless Receiver SWEXCELL with One Alarm Output SWPREC1 7 One Zone Fully Supervised Wireless 4 Zone Fully Receiver Supervised Wire
Download Pdf Manuals
Related Search