User manual
Contents
1. www prolight co uk INTENSE 19T3 RGB LED SLIM PANEL Order code LEDJ255 User manual LEDJ Intense 19T3 RGB LED Slim Panel Safety WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty LEDJ Intense 19T3 RGB LED Slim Panel Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution Never remove warning or informative la2. of 3 pin 5 Pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The Chart below details the correct cable conversion 5 Pin XLR socket Pin E GND Se ra Bn sen Pin 2 Sj pin 3 Bienal H Pin XLR socket Bin TEN ecran in soc L screen Pin 1 GND screen Pin 2 Signal ar Pin 2 Signal Pin E Signal Pin 3 Signal Pin Pin 8 NC LEDJ Intense 19T3 RGB LED Slim Panel Notes Notes LEDJ Intense 19T3 RGB LED Slim Panel Notes Notes Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with seperate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please seperate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mix
3. 9 high Master slave mode To set the unit as the master simply use any of the modes on this unit To set the unit as a slave unit s press the MODE button on the LED display to show SLAv on the LED display Now the unit will follow in sequence with the master unit DMX charts 3 channel DMX chart CHANNEL VALUE FUNCTION Red 0 100 Green 0 100 Blue 0 100 FUNCTION Om TT LEDJ Intense 19T3 RGB LED Slim Panel DMX Charts 9 channel DMX chart ann En nn TT nn Taa namen RC Note 1 Inner pixel 2 Middle pixel 3 Outer pixel 11 channel DMX chart CHANNEL VALUE FUNCTION 0 255 Red 1 0 100 0 255 Green 1 0 100 0 255 Blue 1 0 100 e L eze En 0 255 Red 3 0 100 De cs ese TT a neri Da cs o am Note 1 Inner pixel 2 Middle pixel 3 Outer pixel LEDJ Intense 19T3 RGB LED Slim Panel DMX Set up DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers ADMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX Linking e DMX is a language allowing all makes and models of different manufactures to be linked together and operate fro
4. bels from the equipment Do not open the equipment and do not modify the equipment Do not connect this equipment to a dimmer pack Do not switch the equipment on and off in short intervals as this will reduce the system s life Only use the equipment indoors Do not expose to flammable sources liquids or gases Cleaning must be done at regular intervals Before cleaning wait until the unit has cooled Use a vacuum or dry compressed air and a soft brush to remove the dust collected on the external vents and accessible internal components Clean the external surfaces with a mild solution of non ammonia glass cleaner or isopropyl alcohol and wipe with a soft lint free cotton cloth or lense cleaning tissue Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable Make sure that the available voltage is between 100V 240V Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically e If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again e If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equi
5. e static colour mode press the MODE button on the LED display to show Colt on the LED display To change the brightness of each colour please see below Red Adjustment To adjust the brightness of the red LEDs press the MODE button to show t255 on the display Now press use the UP and DOWN buttons to adjust the brightness from 000 255 To confirm your choice press the ENTER button Note 000 off 255 full on Green Adjustment To adjust the brightness of the green LEDs press the MODE button to show G255 on the display Now press use the UP and DOWN buttons to adjust the brightness from 000 255 To confirm your choice press the ENTER button Note 000 off 255 full on Blue Adjustment To adjust the brightness of the blue LEDs press the MODE button to show B255 on the display Now press use the UP and DOWN buttons to adjust the brightness from 000 255 To confirm your choice press the ENTER button Note 000 off 255 full on Built in programme mode To access the static colour mode press the MODE button on the LED display to show Pr01 on the LED display Now use the UP and DOWN buttons to scroll the built in programmes from Pr01 to Pr12 To change the speed of the selected programme press the ENTER button and use the UP and DOWN buttons to set the speed from 00 to 99 To add strobe pres
6. ed with other commercial wastes for disposal Create Ihe right effect www prolight co uk
7. gure 1 Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight dealers Figure 1 Please guote CABL10 2M CABL11 5M CABL12 10M Also remember that DMX cable must be daisy chained and cannot be split Notice Be sure to follow figures 2 amp 3 when making your own cables Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out MM ra E DMX 512 in 3 pin XLR Oj Mx 3 pin XLR gt DMX u RE SEN EE SEELE eee i S S LR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 11 o Pin 1 Ground i i l Pin 2 Negative 3Hot 3 Hot Pin 3 Postive FIGURE 3 FIGURE 2 Special Note Line termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behaviour Termination reduces signal transmission problems O and interferance it is always advisable to connect a DMX terminal resistance 120 Ohm 1 4 W between pin 2 DMX and pin 3 DMX of the last fixture Using a cable terminator part number CABL90 3 pin CABL89 5 pin will decrease the possibilities of erratic behaviour 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for data transmission in place
8. m a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA Cable DMX cable requirements for DMX operation The LEDJ Intense 19T3 RGB can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output figure 1 Figure 1 Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight dealers Please quote CABL10 2M CABL11 5M CABL12 10M Also remember that DMX cable must be daisy chained and cannot be split LEDJ Intense 19T3 RGB LED Slim Panel DMX Set up DATA Cable DMX cable requirements for DMX operation The Intense Series can be controlled via DMX 512 protocol The DMX address can be set on the back of the fixture Your fixture and your DMX controller reguire a standard 3 pin XLR connector for data input output fi
9. pment switched off until it has reached room temperature If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service Only use fuses of same type and rating Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS WARRANTY One year from date of purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks LED failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property LEDJ Intense 19T3 RGB LED Slim Panel Technical specifications You should find inside the LEDJ carton the following items 1 Intense 19T3 RGB LED Slim Panel 2 Instruction manual 3 Power cable Technical Specifications DMX Channels 3 6 9 or 11 selectable 19 x 3W tri colour LEDs Beam angle 28 degrees Static colour colour change colour fade auto sound active master slave and DMX modes Rainbow pixel effect IEC power in sockets 3 Pin XLR in out sockets 4 push button menu with LED display Twin hanging floor bracket Convection cooled Power Cons
10. s the ENTER button again and use the UP and DOWN buttons to set strobe from 00 to 99 To confirm your setting press the ENTER button Note 00 slow 99 fast In Pr01 you can set a specific static colour When in Pr01 press the ENTER button and use the UP and DOWN buttons to scroll through the list of built in static colours 0 White o 1 Red 2 Amber 3 lt Spring yellow 4 Green 5 Cyan 6 Blue 7 Purple 8 Pink 9 Yellow Off Blackout To add strobe press the ENTER button again and use the UP and DOWN buttons to set strobe from 00 to 99 To confirm your setting press the ENTER button Note 00 slow 99 fast Auto run mode To access the auto run mode press the MODE button on the LED display to show AUTO on the LED display To change the speed of the auto run press the ENTER button and use the UP and DOWN buttons to set the speed from 00 to 99 To add strobe press the ENTER button again and use the UP and DOWN buttons to set strobe from 00 to 99 To confirm your setting press the ENTER button Note 00 slow 99 fast LEDJ Intense 19T3 RGB LED Slim Panel Operations Sound active mode To access the sound active mode press the MODE button on the LED display to show SU00 on the LED display Now use the UP and DOWN buttons to set sound sensitivity level from 00 31 Note 00 low 9
11. umption 68W Power supply 100 240V 50 60Hz Dimensions 260 x 93 x 295mm Weight 2 7Kgs Overview POWER IN POWER OUT DMX OUT 100 240V OISOHZ 100 240V 60 50HZ Identification Hanging floor bracket Earth screw LED display Function buttons DMX input socket DMX output socket 1 IEC power in socket IEC power out socket Hanging bracket tightening knobs 10 Safety bond point 11 Clamp mounting point 11 OMNOARWN gt Setup Operating Instructions The Intense 19T3 RGB is a DMX 512 controllable full RGB colour mixing Par Can made up of high efficiency 3W LED s There are three colour groups red blue and green whose intensity can be controlled individually allowing the creation of an unlimited range of colours The Intense 19T3 RGB will operate in Stand alone Master Slave Sound activated and DMX 512 control modes LEDJ Intense 19T3 RGB LED Slim Panel Operations DMX mode To access the DMX mode press the MODE button on the LED display to show d001 on the LED display Now press the ENTER button and use the UP and DOWN buttons to set the desired DMX address setting from d001 d512 Once you have selected the desired DMX address setting press the ENTER button to choose one of the 3 6 9 or 11 DMX channel modes use the UP and DOWN buttons and press the ENTER button to confirm the setting Static colour mode To access th
Download Pdf Manuals
Related Search