OWNER`S MANUAL
Contents
1. extensions to deflect hot exhaust away from the Raxter or return your Raxter before using REGULARLY CHECK THAT ALL HARDWARE IS IN PLACE AND TIGHT THE CARRIAGE BOLTS USED TO ATTACH CROSSBARS TO THE MAIN TUBE SHOULD BE CHECKED BEFORE EACH USE TO INSURE THEY ARE IN PLACE AND TIGHT DO NOT REMOVE OR OVERTIGHTEN SOCKET HEAD CAP SCREWS USED IN CLAMPING THE SWING ARM Item 5 Figure 2 of Parts Breakdown Section TO ITS PIVOT REMOVING OR OVERTIGHTENING THESE SCREWS CAN CAUSE BREAKAGE OF THE SWING ARM AND POSSIBLE LOSS OF BIKE DURING USE RECOMMENDED TORQUE IS 20 IN LB See note in How to Use section USE ALL 4 STRAPS PROVIDED FOR SECURING EACH BIKE TO THE RACK FAILURE TO DO SO COULD CAUSE LOSS OF BIKE DURING USE Ili ASSEMBLY INSTRUCTIONS Slide each cross bar assembly into a saddle with wheel trays up Insert M8 carriage bolts into saddle and install M8 lockwashers flat washers and acorn nuts onto each carriage bolt and tighten securely Affix Raxter decal on end crossbar as shown Check Acorn nuts for tightness before each use CARRIAGE BOLT MAS FLAT WASHER MB LOCK WASHER M8 ACORN NUT raster DEC AL IV HOW TO USE 1 Unwrap all straps and pivot swing arms open wide enough to accommodate bicycle o e 3 D 2 Load bike onto rack with each wheel in a wheel tray Center bike on rack One at a time rotate each swing arm and shoe upward until it contacts each tire Snugly wrap2. ART JUMBER DESCRIPTION P 10370 E T 2 1 1064c TUBE MAIN OFFSET P 1080c DECAL FRAME RAXTER 1 3 4 V 1077 MANUAL 2 2 BIKE 5 P 1123 PIN SNAP DOMED 5 8 CROSSBAR COMPLETE ASSY PLUS TWO PN 1 10514 ITEM NO PART NUMBER DESCRIPTION 1 P 10800 DECAL FRAME RAXTER 1 P 103 7a CAP PRO 1 1066c TUBE MAIN EXTENSION 2 ASSY 1 P 1052 BOLT HEX 378 164 3 2 5 P 1054 WASHER LOCK 3 8 2 P 1053 NUT 3 8 16 2 1 1097g CROSSBAR COMPLETE ASSY 2 Attach 2 bike extension to rack using 2 3 8 16 x 3 bolts with lock washers and nuts as shown 318 16 X 3 BOLTS N LOCKWASHERS NUTS TARSUS 2 PN 1 1110 TEM NO PART NUMBER DESCRIPTION US 1 1067 MECHANISM FOLDING 2 DOUBLE ASSY 1 1 1097a CROSSBAR COMPLETE ASSY P 1080c DECAL FRAME RAXTER 1 FOLDING MECH 2 PN 1 1067 TEM NO PART NUMBER DESCRIPTION QTY 1 1072 TUBE MAIN PIVOT 1 Z 1 107 TUBE HITCH PIVOT P 1109 PIN SNAP DOMED 1 2 hi0 B 1037a 5 P 1113 BOLI HEA 162 139 6 P 1112 SUT LOC K T 2 1372INC P 1123 PIN SNAP DOMED 5 8 Folding mechani
3. at the factory and under normal circumstances should need no further adjustment These screws provide for adjustability of rotational resistance of the swing arm and provide structural integrity to the swing arm clamp Proper tightness of the screws will allow for rotation resistance of the swing arm of 5 15 pounds of force at the end of the swing arm opposite the pivot Ideally torque should be adjusted with a torque wrench However if a torque wrench is not available tighten or loosen each socket head cap screw turn at a time 74 turn of one screw then turn of the other checking swing arm rotation resistance after each adjustment until acceptable resistance is achieved Under no circumstances should the screws be so tight as to lock the swing arm in place This prevents proper operation of the rack as well as possibly leading to failure of the swing arm in the clamp area and allowing the potential for loss of bike during use Under no circumstances should the screws be removed or loosened to the point that the screws can rattle in their bores This can also lead to catastrophic failure of the swing arm in the clamp area For RAXTER Racks equipped with the RAXTER Quick Pin 1 When installing rack slide rack partially into hitch until button is against the edge of the hitch 2 Press the button on the Quick Pin then insert rack slightly further into hitch until button is engaged in hitch tubing If removing rack press the
4. button and slightly slide rack out of hitch until button is engaged in hitch tubing 3 Once button is engaged in hitch tubing remove finger from button and slide rack into hitch until button pops through hitch hole or finish removing rack from hitch IMPORTANT Be sure to remove finger from button after button is partially engaged in hitch tubing to avoid injury to finger DO NOT PUSH YOUR FINGER INTO HOLE The rack can then be fully installed or removed Make sure Quick Pin Button is fully engaged in hitch hole and give a firm tug on rack to insure rack is properly secured in hitch WERIC LE PATEH DEPRESS BUTTON SLIGHTLY WHEN INSTALLING OR REMOVING Raxter RACK DO NOT PUT FINGER IN HOLE Raxter RACK V PARTS BREAKDOWN ai 4 10 2 NUT LOCK NYLOCK Mel 4 5 rosa 8 WHEEL VELCRO 4 9 Lee FEMALE 4 STINGER 1 25 PN 1 1046a NO PART NUMBER DESCRIPTION QTY 1 1062a TUBE BIKE 125 1097c CROSSBAR COMPLETE ASSY ae wii 103 CAP 1 29 1109 PIN SNAP DOMED 1 2 DECAL FRAME RAXTER 1 STINGER 2 PN 1 1047a ITEM NO PART NUMBER DESCRIPTION QTY 1 1065a TUBE 1 BIKE CROSSBAR COMPLETE ASSY 0370 CAP PEO PIN SNAP DOMED 5 8 DECAL FRAME RAXTER 1 DUOPOD PN 1 1049e TEM NO P
5. elephone number listed above will provide the purchaser with the appropriate mailing address and any additional instructions Please note that the purchaser will be responsible for the cost of mailing the product to RAXTER and that proof of purchase in the form of an original purchase invoice or receipt and a detailed description of the defect must be included in the mailing DISCLAIMER OF LIABILITY REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUCT OR THE ISSUANCE OF A REFUND OR CREDIT AS DETERMINED BY RAXTER IS A PURCHASER S EXCLUSIVE REMEDY UNDER THIS WARRANTY DAMAGE TO A PURCHASER S VEHICLE CARGO AND OR TO ANY OTHER PERSON OR PROPERTY IS EXCLUDED THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE RAXTER S SOLE LIABILITY TO ANY PURCHASER IS LIMITED TO THE REMEDY SET FORTH ABOVE IN NO EVENT WILL RAXTER BE LIABLE FOR ANY LOST PROFITS LOST SALES OR FOR ANY CONSEQUENTIAL DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR PUNITIVE DAMAGES OR FOR ANY OTHER DAMAGES OF ANY KIND OR NATURE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS MAY NOT BE APPLICABLE THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Raxter CAR RACK SYSTEMS LIMITED LIFETIME WARRANTY EFFECTIVE JANUARY 1 2006 Regi
6. raxter RACK YOUR BIKE www raxterracks com OWNER S MANUAL www raxterracks com 3820 West El Paso ST Broken Arrow OK 74012 918 706 7987 Manual No M 1169 TABLE OF CONTENTS Introduction ll Precautions and Warnings III Assembly Instructions IV How to Use V Parts Breakdown Vi Warranty and Disclaimer I INTRODUCTION Congratulations on your purchase of the Raxter bike rack This rack represents the fusion of creative design modern material usage and sturdy construction techniques The Raxter is an easy to use fast loading and robust design It is lightweight and thus easy to install remove and store The Raxter provides you with the ultimate value in bike racks With proper care your Raxter should provide you with many years of trouble free service Thank you for the purchase of your Raxter ll PRECAUTIONS AND WARNINGS RACK CAPACITY IS 40 POUNDS PER BIKE 40 POUND TOTAL WEIGHT FOR SINGLE RACKS 80 POUNDS TOTAL WEIGHT FOR 2 BIKE RACKS 160 POUNDS FOR 2 BIKE RACKS WITH 2 BIKE EXTENSION When using the Quick Pin be sure to remove finger from button after button is partially engaged in hitch tubing to avoid injury to finger DO NOT PUSH YOUR FINGER INTO HOLE MAKE SURE THAT THE RAXTER IS NOT DIRECTLY IN LINE WITH THE VEHICLE S EXHAUST HOT EXHAUST CAN DAMAGE BIKE TIRES AND CAN CAUSE CATASTROPHIC DAMAGE TO YOUR RAXTER If the Raxter is directly in line with the vehicle s exhaust add exhaust
7. shoe straps around tire and rim being careful not to wrap a strap over a valve stem Slide wheel tray straps directly under the center of each wheel and snugly wrap straps around tire and wheel Make sure that straps do not wrap over a valve stem Do not drive vehicle without securing all straps on each bike Note If loading bikes with small rims and tires such as road bikes in which the wheel tray straps do not contact rims when straps are wrapped over rim move strap on front wheel forward and strap on rear wheel rearward so that straps are in firm contact with the rim where rim rises above top of wheel tray due to curvature of rim This will insure stability of bike s during transport and help prevent side to side shifting during extreme cornering 3 When loading multiple bikes face each adjacent bike in the opposite directions It normally eases loading to move each bike a few inches forward allowing seat seat tube and handlebar clearance This is a unique feature of your Raxter Make sure that crank arms pedals handlebars and seats seat tube are not rubbing against one another 4 When not in use wrap straps around wheel trays and shoes Fold swing arms downward until flat Note Proper tightness of socket caps screws Item4 Figure 1 in Parts Breakdown Section in the swing arm s pivot clamp is important Recommended torque is 20 in Ib The torque of these screws is preset
8. sms for Tarsus and Thorax racks are operated as demonstrated below DEPRESS BUTTON SLIGHTLY ROTATE RACK UPWARD DO NOT PUT FINGER IN HOLE DO NOT PUT FINGER IN HOLE DEPRESS BUTTON SLIGHTLY ROTATE RACK DOWNWARD DO NOT PUT FINGER IN HOLE DO NOT PUT FINGER IN HOLE 10 TARSUS 1 25 PN 1 1111 le TEM NUMBER DESCRIPTION QTY 1 10996 MECHANISM FOLDING 1 25 DOUBLE ASSY 1 7 pleas E 2 1 1097a CROSSBAR COMPLETE ASSY 2 3 P 1080c DECAL FRAME RAXTER 1 PE FOLDING MECH 1 25 PN 1 1099a ITEM NO PART NUMBER DESCRIPTION QTY I 1104 TUBE MAIN FOLDING 1 1 025 TUBE HITCH FOLDING P 1 105 BOLT HEX gjo L 2 20 P 1106 NUT LOCK 3 8 16 P I0360 GAP L25 A 1 23 P 109 PIN SNAP DOMED 172 B IN THORAX PN 1 1142 Na FOLDING MECH 1 25 3 BIKE PN 1 1139 ITEM NO PART NUMBER DESCRIPTION QIY l 1140 TUBE MAIN FOLDING l l 1102b TUBE HITCH FOLDING P 1105 JBOLI HEX 3 8 16 X 2 25 P 1 106 NUT LOCK 3 8 16 P 1036a GAF L29 A L23 2 2 P 1 109 PIN SNAP DOMED 1 2 VI WARRANTY AND DISCLAIMER RAXTER LLC will warranty all RAXTER LLC brand car rack systems during the period that an original retail purchaser owns the product An exception applies to the wheel securing straps which will be
9. ster online at www raxterracks com register 15
10. warrantied for a period of 3 years from the time of original purchase This warranty terminates if a purchaser transfers the product to any other person Subject to the limitations and exclusions described in this warranty RAXTER will remedy defects in materials or workmanship by repairing or replacing at its option a defective product without charge for parts or labor In addition RAXTER may elect at its option not to repair or replace a defective product but rather issue to a purchaser a refund equal to the purchase price paid for the product or a credit to be used toward the purchase of a new RAXTER bike rack system No warranty is given for defects caused by normal wear and tear cosmetic rust scratches accidents unlawful vehicle operation or modification of or any types of repair of a bike rack system other than those authorized by RAXTER No warranty is given for defects resulting from conditions beyond RAXTER s control including but not limited to misuse overloading or failure to assemble mount or use the product in accordance with RAXTER LLC s written instructions or guidelines included with the product or made available to the purchaser In the event that a product is defective the purchaser should contact RAXTER in writing or by phone at Raxter Attn Customer Service 3820 W El Paso ST Broken Arrow OK 74012 918 706 7987 In the event that a product needs to be returned to RAXTER a RAXTER technician at the address or t
Download Pdf Manuals
Related Search