3MP Interior Exterior Camera IPFD3TI
Contents
1. Extension Cable NO Item Description Ethernet RJ 45 port compatible 1 RJ45 with 10 100Mbps PoE Modular Jack 2 DC Jack Main Power DC Jack DC12V Al Alarm In 3 G GND AO Out Alarm input and output 3pin terminal MIC Audio In 4 G GND Audio line input 2pin terminal SPK Audio Out 5 G GND Audio line output 2pin terminal 2 2 Installing Camera Carefully remove the contents from the box and verify that nothing was damaged in ship ment Surface Type 1 Loosen the three torx screws located midway up the front of the housing leave the screws intact in the front portion Fig 1 2 Drill the mounting location using the supplied Drilling Guide Label Fig 2 3 Attach the surface Mount to the ceiling or wall using suitable fasteners The supplied M5x30 tapping screws are used only if they are applicable Fig 2 4 Insert the bottom case into the surface mount and turn the locking flap to fasten the bottom case to the surface mount using 3 screws Fig 3 Fig 4 5 Close the housing by fastening three torxscrews Torx Screws M4x10 3x Drilling Guide Label Flush Type Hole 116mm Mounting Screw M5x30 2x Surface mount Fiqure 2 10 Locking Flap s Screws x3 Locking Flap x3 CEILING WALL Note The ceiling tile must be thicker than 0 15inch 37mm 1 Loosen the2. has been spilled or ob jects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING IN STRUCTIONS UNLESS YOU QRE QUALIFIED TO DOSO 16 Use satisfy clause 2 5 of IEC60950 1 UL60950 1 or Certified Listed Class 2 power source only 17 ITE is to be connected only to PoE networks without routing to the outside plant Contents 1 Introduction 6 E21 Components brit eae wegen Alaa ee ae 6 Features sh ze a os OO ea Be 7 Installation 8 2 XJVOLVIOW a eat cet tete we og p sawed Oe em QE ad 8 2 2 Installing Camera a m UE A ig 9 2 3 POONNEENON isset isa 13 2 4 Resetting to the factory default settings 14 Appendix 15 O pelo Me Speeiiealon s mss ice et s 15 1 Introduction This installation manual applies to the IPFD3TI networkcamera The network camera is fully featured for security surveillance and remote monitoring needs Itis based on the DSP compression chip and makes it available on the network as real time full frame rate Motion JPEG and H 264 videostreams The alarm input
3. on events Mechanical or electrical switches can be wired to the Al Alarm In and G Ground connectors G Ground Connect the ground side of the alarm input and or alarm output to the G Ground connector AO Alarm Out The network camera can activate external devices such as buzzers or lights Connect the device to the AO Alarm Out and G Ground connectors Connecting the Power Connect the power of 12 450mA for the network camera Connect the positive pole to the position and the negative pole to the position for the DC power Be careful not to reverse the polarity when connecting the power cable A router featuring PoE Power over Ethernet can also be used to supply power to the camera For the power specifications refer to the Appendix Product Specification f PoE and 12 VDC are both applied the camera will be supplied with power from PoE Connecting Audio Connect Speaker to Audio line output and external Mic to Audio input line 14 2 4 Resetting to the factory default settings To reset the network camera to the original factory settings go to the Setup gt System gt Maintenance web page described in System gt Maintenance of User s Manual or use the Reset button on the network camera as described below Reset Button Using the Reset button Follow the instructions below to reset the network camera to the factory default settings us in
4. 4 1280x720 960 Video Resolution 1024x768 704x480 576 640x360 480 320x240 Video Video Frame Rate Max 25fps 30fps Audio Video Streaming 25 30fps Triple Stream H 264 x 2 MJPEG x 1 Composite Out Audio Compression G 711 Audio Streaming 2 Way Video Contents Analysis Line Detector Field Detector Motion Detection Area 16 Programmable Area Include Area 8 Exclude Area8 Privacy Mask 8 Programmable Zone FTP Uploading MJPEG E mail FTP Notification Server Event Notification XML Notification Audio Alert AIHM Audio Alert User Defined 3 Audio files Login Authority Administrator Operator Guest System FTP Pre 30sec Post 30sec Event Buffering SD Record Pre 10sec Post 60sec Manual Trigger 4 Programmable Trigger Security Multi User Authority IP Filtering HTTPS SSL Network Time Sync NTP Server Synchronize Computer Manual Software Reset Restart Reset Factory Default Hardware Factory Reset Yes Auto Recovery Backup Restore Remote Upgrade Web Browsing IE Chrome Safari Firefox SmartManager SD Recording Mode Event Continuous 16 Protocols TCP IP UDP IPv4 IPv6 HTTP HTTPS QoS FTP UPnP RTP RTSP RTCP DHCP ARP Zeroconf Bonjour Client Software Web SmartManager Client S W Mobile S W User Connection Live 10 Users Playback 3 Users API Support Open API ONVIF Compliance M
5. INSTALLATION MANUAL Onvir IP INTERIOR EXTERIOR DOME CAMERA IPFD3TI Please read this manual thoroughly before use and keep it handy for future reference WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EX POSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is in tended to alert the user to the presence of dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product FCC COMPLIANCE STATEMENT This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful inter ference and 2 this device must accept any interference received including interference that may cause undesired operation FCC INFORMATION T
6. and alarm output can be used to connect various third party devices such as door sensors and alarm bells 1 1 Components This system comes with the following components Dome Camera 1 Installation Guide CD 1 Drilling Guide Label 1 1 Accessory Kit Note 1 Check your package to make sure that you received the complete system includ ing all components listed above Note 2 Adapter for DC 12V is not supplied 1 2 Key Features Brilliant video quality The network camera offers the highly efficient H 264 video compression which drasti cally reduces bandwidth and storage requirements without compromising image qual ity Motion JPEG is also supported for increased flexibility Wide Dynamic Range The network camera provides digital WDR Wide Dynamic Range that improves video exposure quality in scenes with high contrast between bright and dark areas in the video for example a shady area and a sunny area in the same scene Dual or Triple Streams The network camera can deliver dual or triple video streams simultaneously at full frame rate in all resolutions up to 2048 x 1536p using H 264 and Motion JPEG This means that several video streams can be configured with different compression formats resolutions and frame rates for different needs Intelligent video capabilities The network camera includes intelligent capabilities such as enhanced video motion detection The network cameras external inputs and outputs can
7. be connected to de vices such as sensors and relays enabling the system to react to alarms and activate lights or open close doors Improved Security The network camera logs all user access and lists currently connected users Also its full frame rate video can be provided overHTTPS PoE Power over Ethernet This network camera can be powered through PoE IEEE802 3af which simplifies installation since only one cable is needed for carrying power as well as video controls ONVIF Certificate This is a global interface standard that makes it easier for end users integrators con sultants and manufacturers to take advantage of the possibilities offered by network video technology ONVIF enables interoperability between different vendor products increased flexibility reduced cost and future proof systems Micro SD Recording support The Network Camera also supports a micro SD memory slot for local recording with removable storage of type SDHC and SDXC Audio support The Network Camera also supports two way audio 2 Installation For the operation of the Network Camera it is necessary to connect a network cable for data transmission power connection from supplied power adapter Depending on operation methods it is possible to connect an alarm cable additionally For its fixation on different locations please consult with aninstaller 2 1 Overview e Dimension 99 0 INNER 093 0 113 9 54 7 0143 4
8. g the Reset button 1 Switch off the network camera by disconnecting the power adapter Press and hold the Reset button while reconnecting the power Keep the Reset button pressed for at least 2 or more seconds Release the Reset button a C N The network camera resets to factory defaults and restarts after completing the factory reset CAUTION When performing a Factory Reset you will lose any settings that have been saved Default IP 192 168 30 220 Appendix Product Specification Model Network Camera Lens Varifocal 2 8mm 12 0mm F1 4 DC IRIS Angle of View 97H 37 H Type 1 2 8 Sony Exmor CMOS Image Sensor Pixels 2048 H x 1536 V Color 0 1 Lux F1 4 Min Illumination B W 0 Lux F1 4 Scanning Mode Progressive Scan Wide Dynamic Range D WDR Day and Night Mode True D N Auto Day Night Image Noise Reduction 2DNR 3DNR Digital Zoom Yes ROI Exposure Control Auto Auto White Balance Control Auto Incandescent Fluorescent Outdoor Manual Back Light Compensation Yes Image Effect Flip Mirror Aisle Defog HLC S LDC Flicker Free Mode 50Hz 60Hz Shutter Speed Auto 1 10 000 1 sec Manual Quality 30 IR LEDs Angle 76 Distance up to 30m Video Compression H 264 Baseline Main High Profile MJPEG Bitrate Control CVBR VBR 2048x1536 1920x1080 1280x102
9. his equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commer cial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the in struction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful in terference in which case the user will be required to correct the interference at his own expense CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme 003 du Canada CE COMPLIANCE STATEMENT WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions 2 Keep these instructions 3 Heed all warning
10. obile Support Android i OS Audio 1 Input 1 Output Terminal Block External Alarm 1 Input 1 Output Terminal Block In Out Ethernet RJ 45 10 100Base T SD Card SDHC SDXC Operating Humidity 0 90 RH Non condensing Operating Temperature 309C 45 C Power Supply PoE IEEE802 3af compliant Class0 12VDC ETC Power Consumption DC 12V 450mA 5 4W PoE 120mA 5 7W with IR on Dimensions 143 4mm x 113 9mm H Net Weight Approx 720g Ingress Protection IP66 gt Specifications are subject to change without notice 17 En IP INTERIOR EXTERIOR DOME CAMERA IPFD3TI 50303945A
11. s 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturers in structions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs conve nience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used Use caution when moving the cart apparatus combination to avoid in jury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is re quired when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid
12. three torx screws located midway up the front of the housing leave the screws intact in the front portion Fig 1 2 Remove the ceiling tile from the ceiling Draw a circle whose diameter is 116mm on the tile You can user carton with a hole Cut the circle out of the ceiling tile Fig 2 3 Insert the bottom case into the ceiling tile and turn the locking flap to fasten the bottom case to the ceiling tile using 3 screws Fig 3 Note When installing the camera flush with the ceiling three locking flaps hold firmly which makes it easy to install Fig 4 4 Close the housing by fastening three torx screws Torx Screws Locking M4x10 3x la PT Drilling Guide Label Flush Type Hole 116mm Figure 2 12 Locking Flap s Screws x3 Locking Flap x3 CEILING WALL 13 2 3 Connection e Micro SD memory card insertion Remove the bubble of the camera to insert the SD memory card s i o A gt ii 2 2 g 4 T JS Connecting to the RJ 45 Connect a standard RJ 45 cable to the network port of the network camera Generally a cross over cable is used for directly connection to PC while a direct cable is used for connection to a hub You can also use a router featuring PoE Power over Ethernet to supply power to the camera Connecting Alarms Al Alarm In You can use external devices to signal the network camera to react
Download Pdf Manuals
Related Search