Autoline 410 Manual
Contents
1. e Ensure the calibration values have been verified Outputs e Ensure all outputs activate the intended guns Marked Pattern Module Length e Mark at least four modules of a line gap pattern e g 3m line 9m gap in a straight line ata constant and typical marking speed e Measure from the start of the second line to the start of the third line and the start of the third line to the start of the fourth line The first line is not used for checking in case there is a sticking gun etc e The distances measured should be equal to the line gap sum of the pattern This further validates that the speed calibration is correct and the system is measuring distance correctly Set Line Adjust Measure the length of the second third and fourth lines marked Compare these lengths with the required pattern length e Use the Line Adjust setting to increase decrease the line length This will compensate for the mechanical delays within the system Mark another set of four modules and measure new line lengths e Repeat process until line length matches required pattern length Note Check the air system solenoids and guns if consistent line lengths cannot be achieved Ensure the air hoses going from the air solenoids to the guns are kept to a minimum length Ensure installed air hoses installed have a suitable aperture Ensure that the air pressure is stable Check operation of guns Set Spot Length if applicable e Mark out at least t2. Cycle feature retards advances pattern cycle during re marking applications Full graphic display with continuous speed readout in metres or feet Speed alarm function Suitable for profile vibraline applications Adjustable spot marking mode Layout wizard Automatic calibration wizard Bulit in user pattern for field programming PC utility available to edit patterns Specifications Power Supply 9 30VDC Operating Temperature 5 to 60 deg C 23 to 140 deg F No Sensor Inputs 1 Input speed Sensor Input Polarity Negative switched NPN or Positive switched PNP No Trigger Inputs 2 Inputs Trigger Input Polarity Negative switched NPN or Positive switched PNP No Outputs 2 Outputs Output Polarity Positive switched PNP Output Current max 3 5A Display Type Transflective LCD Dimensions W x H x D 104mm x 112mm x 24mm 4 1in x 4 4in x 0 9in Enclosure ABS Sealing IP65 NEMA4 Compliant not including cable entry Notes Refer to the wiring diagrams for further electrical information Autoline 410 Controller User Manual Installation Mounting The Autoline controller should be mounted in a location where the operator can view the screen and touch the keys with ease The Autoline controller should be mounted on a flat surface The mounting fasteners should be finger tightened See below for mounting drill guide Available as an option is the Autoline Mount
3. e This type of sensor is installed into the speedometer cable port of the gearbox e Typical pulse resolution is 100ppm 30p ft Digital Multiplier e This device connects to the vehicle s onboard electronic speed signal and multiplies the output resolution so that it is suitable for roadmarking use e Multiplication factor options include x8 x16 x32 Drive Shaft Collar e This consists of a sensor such as a proximity or hall effect sensor mounted to detect movement from a gear toothed or magnetic disc mounted to the drive shaft Further technical information and installation details are available Contact the manufacturer or distributor Triggers Trigger inputs use mechanical switches to activate marking outputs These are typically mounted in a convenient location for the operator to use The trigger inputs can either be an NPN or PNP open collector signal depending on the Input Type selection found in the Calibration sub menu NPN input type is recommended and the default setting Refer to wiring diagrams for installation wiring Either standard trigger switch assemblies from the manufacturer can use used or a custom trigger switch assembly can be made Contact the manufacturer or distributor for options Autoline 410 Controller User Manual 29 Product Warranty amp Disclaimers 12 Month Limited Warranty Novo Innovation Ltd warrants only to the purchaser of the Product from Novo Innovation Ltd the Cus
4. NOVO INNOVATION Hi Tech Roadmarking Solutions USER MANUAL Up Down AVO Autoline 410 Standalone Roadmarking Controller Rev 2 1 Autoline 410 Controller User Manual l Table of Contents Safety Information Introduction Specifications Installation Main Operation Menu Access amp Navigation Setup Menu Operating Menu Normal Marking Mode Operation Layout Wizard Mode Setup Checklist Pattern Editing PC Based Pattern Editing Program Built in User Pattern Function Sensors Triggers Product Warranty and Disclaimers Appendices Appendix A Software Update amp Revision History Appendix B Document Revision History Autoline 410 Controller User Manual 13 15 17 18 19 19 19 22 22 23 23 23 23 Safety Information Please read the following safety information Equipment misuse can cause equipment malfunction resulting in serious injury e Read and understand all manuals wiring diagrams and any other supporting documentation provided in full before installing or operating the equipment e A Suitably qualified technician must carry out installation e This equipment is for professional use only All operators must be suitably qualified and trained to use the equipment e Use the equipment only for its intended purpose Contact the manufacturer or distributor if you are unsure of any aspects of installation or operation e Do not alter or modify this equipment Installati
5. TION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE CUSTOMER S SOLE REMEDY FOR ANY DEFECTIVE PRODUCT WILL BE AS STATED ABOVE AND IN NO EVENT WILL NOVO INNOVATION LTD BE LIABLE FOR INCIDENTAL CONSEQUENTIAL SPECIAL OR INDIRECT DAMAGES IN CONNECTION WITH THE PRODUCT This Limited Warranty shall be void if the Customer fails to comply with all of the terms set forth in this Limited Warranty This Limited Warranty is the sole warranty offered by Novo Innovation Ltd with respect to the Product Novo Innovation Ltd does not assume any other liability in connection with the sale of the Product No representative of Novo Innovation Ltd is authorized to extend this Limited Warranty or to change it in any manner whatsoever No warranty applies to any party other than the original Customer Novo Innovation Ltd and its directors officers employees subsidiaries and affiliates shall not be liable for any damages arising from any loss of equipment loss or distortion of data loss of time loss or destruction of software or other property loss of production or profits overhead costs claims of third parties labour or materials penalties or liquidated damages or punitive damages whatsoever whether based upon breach of warranty breach of contract negligence strict liability or any other legal theory or other losses or expenses incurred by the Customer or any third party Obtaining Warranty Service If the Product was purchase
6. ack to the start Note Pattern program lengths apply to the unit setting of the Autoline controller So a L3 will be 3m if Metric units are selected or 3 feet if Imperial units are selected Autoline 410 Controller User Manual 20 Following is a series of pattern program examples to show the use of the pattern programming elements L Generates an indefinite line output Used for solid line generation G Generates an indefinite gap output Used for measurement patterns that require distance measurement but no output generation Also used in counting patterns L30 Generates a 30m line and then STOPS L3G9C Generates a 3m line a 9m gap and then continues with a 3m line a 9m gap and so on LSG12C Generates a distance based spot a 12m gap and then continues with a spot a 12m gap and so on L3G4 5LSG4 5C Generates a 3m line a 4 5m gap a distance based spot a 4 5m gap and then continues with a line a gap a spot a gap and so on Note The following example shows how the C element can be used to jump to a program location other than the start This is done by defining the required element number for the continue point the first element being number 1 G9L1G1C2 Generates a 9m gap a 1m line a 1m gap and then jumps back to the 1m line 1m gap 1m line 1m gap and so on Output configuration Select the output s that are required to be activated by the pattern generator None one or bot
7. can be browsed and selected while the Autoline controller is idle e Use the Ay keys to select pattern cycles Display Modes If the vehicle is stationary speed is zero the screen will always display the distance counters for the pattern cycles If the vehicle is moving the screen can toggle between the speed value and the distance counters being displayed 300 White solid e Press the G key to toggle between speed display and distance counter display Marking Operation Basic marking operation as follows Select a pattern cycle 1 2 Drive vehicle at required application speed 3 Activate trigger to start line outputs Deactivate trigger to stop line outputs When a pattern is active the ID number will be highlighted Pax Press the key to cancel marking immediately Resync Cycle The Cycle ReSync function is used during re painting to advance retard the pattern cycle so the placement of outputted lines matches over the existing lines on the road This function can only be used when the trigger is activated Use the A keys to set the Cycle ReSync distance Multiple key presses will increase the distance in accordance with the ReSync Resolution setting The Cycle ReSync will only be effective for the next line After the next line has started the Cycle ReSync distance will be reset to zero Autoline 410 Controller User Manual 15 Trigger Latch Mode Latch Mode latches ON the line outputs until the complet
8. count The distance count for pattern cycles can be selected to count in two modes Pattern line gap Applied line only ii Painting Setup Minimum speed Offset adjust it Applie line only v ReSync resolution 30 m Distance count Applied About Displays software version details and serial number Autoline 410 Pe a SN 1234 Version 1 48 Operating Menu This menu can only be accessed when the machine is stationary and the Autoline is idle Line Adjust Line Adjust setting compensates for mechanical delays within the system by increasing decreasing the line length output slightly The mechanical delays are be introduced by the air system solenoids and guns etc Line Adjust can be set as either a distance based mm or time based ms value Time based adjustment gives an adjustment independent of the vehicle speed and is the recommended setting Distance based adjustment is a legacy option that provides a constant adjustment based on speed pulses There are two methods to adjust the Line Adjust setting Adjust from menu e Use the A keys to make the adjustments e Use the G key to save the adjustment and exit Adjust during operation At ant time while a pattern is selected e While holding the M key down press the aF keys to make the adjustments Line adjustmen 20 Miliseconds Autoline 410 Controller User Manual 13 Clear Counters Clear this pattern This clears to zero the di
9. d from a Distributor please contact that Distributor to obtain a Returned Material Authorization RMA If the Product was purchased directly from Novo Innovation Ltd please contact us direct at peter novoinnovation co nz or 64 9 419 1219 Customer shall prepay shipping charges for Products returned to Novo Innovation Ltd for warranty service and Novo Innovation Ltd shall pay for return of Products to Customer However Customer shall pay all shipping charges duties and taxes for Products returned to Novo Innovation from outside New Zealand Autoline 410 Controller User Manual 23 Appendix A Software Update amp Revision History Software Update Capability The Autoline controller can have the software updated through the use of the PC based Autoline Pattern Editor program The Autoline controller is connected to the PCB via the Autoline USB cable Please refer to the Autoline Pattern Editing Guide for further details on the software update capability Software Revision History Version Release Date Comments 1 48 13 09 2012 First release Autoline 410 succeeds Autoline 400 Appendix B Document Revision History Revision Release Date Comments 2 1 13 09 2012 First release This publication is intended for reference purposes only All document content and product specifications are subject to change without notice No part of this publication may be reproduced in any form or by any
10. erating menu Ment Clear all patterns Layout wizard Output testing Combine measurements KA Edit user pattern Line Configuration Two individual pattern generators exist Line 1 and Line 2 Each line can be edited separately Combine measurements checkbox The pattern generators can have separate counters for distance measurement or have the measurement combined into a single counter Trigger amp 0o Triggers Trigger B F E Trigger latch enable M Other line Pattern L2G20 Other line latched O Autoline 410 Controller User Manual 19 Counter only checkbox Selecting counter only will produce a pattern with incremental counting functionality 1 2 3 4 there are no outputs enabled This is useful for counting events such as RRPMs pedestrian crossings etc Triggers Configuration Select the trigger input s required to activate the pattern generator Line 2 has the additional options of cascading off Line 1 where the pattern generator can be activated from the other line being active This is useful for thermoplastic applications using profile vibraline Other Line Output This is useful in thermoplastic tactile applications where one line may be a slave of the other The slave line will only be activated if the master line has an active output Other Line Latched This is useful in multiple line barrier and thermoplastic tactile applications where one line may be a slave of the other T
11. eys The gun outputs can still be tested at zero speed if the minimum speed setting is greater than zero This is useful to check gun operation clear nozzle etc Stationary start can be allowed by setting the minimum speed threshold to zero However the outputs will not be activated until the first speed pulse is detected f Painting Setup Target speed Speed margin Minimum st 0 00 Offset adjust Time When minimum speed threshold is set to zero the output testing page will have to be accessed from the operating menu Output testing Output 1 on Output 2 off Line Adjust Units Line Adjust can be set as either a distance based mm or time based ms value Time based adjustment gives an adjustment independent of the vehicle speed and is the recommended setting Distance based adjustment is a legacy option that provides a constant adjustment based on speed pulses Painting Setup set adjust units Target speed Speed margin ReSync resolution The increment length for the Cycle ReSync function is entered into this setting Each key press during Cycle ReSync use will be incremented by this length Example If ReSync resolution set to 30mm and Cycle Resync function has the UP key pressed 3 times the total Cycle Resync distance will be 90mm Painting Setup Minimum speed 0 70 Offset adjust Time ReSyne resolution 30 mm Distance count Applied Autoline 410 Controller User Manual 12 Distance
12. h output s can be configured for each pattern generator An output offset can also be configured These offsets are additional to the offsets set in the painting setup menu The offset provides a permanent distance offset so the output will not activate for a defined distance after the pattern has been activated This is for advanced use only These offsets are additional to the output offsets configured in the painting setup menu which provide better flexibility to the operator Autoline 410 Controller User Manual 21 Speed Sensors For accurate line measurement the recommended minimum speed signal resolution is Metric 100ppm pulses per metre This provides a line accuracy of 10mm Imperial 30p ft pulses per foot This provides a line accuracy of 0 033ft For more accurate line requirements a sensor with greater resolution should be used The speed input can either be an NPN or PNP open collector signal depending on the Input Type selection found in the Calibration sub menu NPN input type is recommended and the default setting Refer to wiring diagrams for installation wiring There are various sensor options available to generate accurate vehicle motion pulses Following are examples of possible options 5 Wheel Encoder e This type of sensor is fitted so it runs along a tyre of the vehicle e Typical pulse resolution options include 100ppm 30p ft 200ppm 60p ft 400ppm 120p ft Gearbox Encoder
13. he slave line will be activated if the master line is active this includes when both line or gaps are being outputted Trigger latch enable checkbox The trigger latching checkbox enables the pattern to operate in semi automatic mode This mode latches ON the line outputs until the completion of the line pattern if enabled in the pattern program This semi automatic functionality is useful for remark work and multiple line barrier applications The Trigger Latching Mode needs to also be enabled in the Painting Setup menu of the Autoline controller A LitSet value Pattern Generator Program The pattern program can be edited by adding elements and editing their values Elements can be added inserted or deleted Select each element to modify value or type Following is a table outlining the basic pattern programming elements Element Description Details L Line Line generation L element is followed by line length e g L3 G Gap Gap generation G element is followed by gap length e g G9 Distance spot generation Length is dependent of spot length setting in Distance Spot the Autoline controller setup menu Time spot generation Duration is dependent of spot length setting in the S Timed Spot Autoline controller setup menu C Continue This element is used to define a jump in the pattern generation Normally Go To is used on the end of the pattern program to jump b
14. ing Kit this includes a mounting plate and a RAM Mount P N RAM B 102U A Alternative mounting options are available The enclosure is rated to IP65 sealing NEMA4 compliant except for the rear cable wire entry This allows the unit to be subjected to low pressure water jets without any harmful ingress of water The rear cable entry allows the enclosure to breathe and dispel moisture Mounting Drill Guide 19mm 0 75in r L 56 3mm 2 22in 78mm 3 07in Autoline 410 Controller User Manual 5 Wiring Installation Refer to wiring diagram for installation wiring Speed Sensor Installation See specific manual chapters for installation details relating to the speed sensor Other information may be located in the wiring diagram and supporting documentation Trigger Installation See specific manual chapters for installation details relating to the triggers Other information may be located in the wiring diagram and supporting documentation Static Strap It is recommended that a static strap be fitted to the vehicle to prevent ESD electrostatic discharge damaging electronic devices Welding Warning All electronic devices must be completely disconnected before any welding is carried out on the vehicle Welding can cause severe damage to sensitive electronic devices Excessive Transient Voltage Warning All electronic devices must be completely disconnected in the event of servicing to the equipmen
15. ion of the line pattern if enabled in the pattern program This semi automatic functionality is useful for remark work and multiple line barrier applications During remark work the start of the line output can be triggered by momentarily activating the input trigger The programmed line length will be outputted and stopped automatically at completion Multiple line barrier applications can be configured so multiple line outputs turn off together when deactivated This provides the uniform line finish that is required in some applications The Latch Mode function is ignored by patterns containing only solid lines This is because these patterns do not have a known end to the line Line Adjust Line Adjust setting compensates for mechanical delays within the system by increasing decreasing the line length output slightly The mechanical delays are be introduced by the air system solenoids and guns etc Adjust during operation At ant time while a pattern is selected e While holding MO key down press the ar keys to make the adjustments Line adjustmen 20 Miliseconds Notifications Release trigger A trigger input is currently activated when the system does not allow trigger activity The most common cause of this is when the painting activity has been disabled due the vehicle speed falling below the minimum speed threshold Autoline 410 Controller User Manual 16 Layout Wizard Mode Operation The layout w
16. izard creates and stores up to five layouts which may be reused or edited at any time The two main types of layout these are designed for straight and angle parking bays General purpose spotting of any size can be done using the Depth spot The three spot pattern lines showing a indicator dot are available to operate at the distance showing The offset pattern has a calculated gap for angle parking use see layout3 below E L length depth and offset and can be edited Stall Size by pressing and using the arrow keys A Stalls or can be re measured by pressing the trigger and Jeoth running the vehicle along the ground then releasing Space i ea the trigger Offset Item Ready to adjust or re measure Examples amp oO 2 g B i space if Length E Angle Highightanduse Min Stall Size ESAR required 3 Stall Size o a space e e pR 2 530 Length Angle Min Stall Size Stall Size Highlight and use function required offset to first space If angle selected there will be no dot at start General purpose spotting example using depth spots Autoline 410 Controller User Manual 17 Setup Checklist This checklist helps outline the required steps for a standard setup Installation e Ensure system components are installed and wired correctly e Refer to wiring diagrams Sensor Calibration e Ensure the speed calibration procedure has been carried out
17. ly at completion Multiple line barrier applications can be configured so multiple line outputs turn off together when deactivated This provides the uniform line finish that is required in some applications The Latch Mode function is ignored by patterns containing only solid lines This is because these patterns do not have a known end to the line Speed Display Accuracy Sets the number of decimal places of the speed display The options are e 0 No decimal place e g 8km hr e ji One decimal place e g 8 4km hr Reverts to no decimal place over 20km hr e 2 Two decimal places e g 8 42km hr Reverts to one decimal place over 10km hr Display accuracy can be adjusted with the Ay keys Speed Alarm Function This function is designed to assist with application rates and QA This function provides visual and audible alarms as the actual speed falls and exceeds the margin set for the target speed value This can be set to off or to a target speed value with the Ay keys The allowed speed margin can be adjusted with tneZ keys Example speed alarm results 696 8 12 Autoline 410 Controller User Manual 11 Minimum Speed This setting determines the minimum speed required to allow marking of pattern outputs If the soeed falls below this threshold the Release Trigger notification will be displayed Default setting is 0 5km hr 0 5 Miles hr Minimum Speed setting can be adjusted with the Ay k
18. means electronic photocopying recording or otherwise without prior written permission of the publisher All brand and product names are trademarks or registered trademarks of their respective companies Novo Innovation Ltd 2012 Novo Innovation Ltd N Ovo P 64 9 419 1219 INNOVATION E peter novoinnovation co nz Hi Tech Roadmarking Solutions www novoinnovation co nz Autoline 410 Controller User Manual 24
19. on and wiring must be strictly in accordance with the instructions provided within the manuals wiring diagrams and any other supporting documentation provided e The Autoline controller must be mounted in a safe position where it is easily visible and will not interfere with the operator s view of the road e Check equipment routinely Repair or replace worn or damaged parts immediately e Comply with all applicable local state and national fire electrical and safety regulations e To avoid serious injury or equipment damage the Autoline controller must be disconnected whenever servicing any part of the roadmarking machine e Operators of equipment must at all times follow occupational health and safety protocols issued by their organization Autoline 410 Controller User Manual 3 Introduction The Autoline 410 roadmarking controller provides an electronic means of controlling pattern generation of roadmarking operations This product range is suitable for paint thermoplastic and cold applied plastic applications Features Quick pattern selection Can paint 1 or 2 lines simultaneously useful for barriers 2 outputs with offsets to help improve beads coverage over paint single line applications only 2 trigger inputs useful for quickly changing between two patterns Adjustable line length compensation Latch mode provides semi automatic operation useful for re marking applications Look ahead triggering ReSync
20. stance counter for the current pattern selected Clear all patterns This clears to zero the distance counters for all patterns Layout Wizard Selecting the Layout Wizard changes operation mode from Normal Marking mode to the Layout Wizard mode See page 17 for further details Output Testing This function allows the outputs to be tested in a stationary manner without a vehicle speed signal This is useful for testing both trigger and output operation and for unblocking the guns etc Output testing Output 1 on Output 2 off To test the outputs activate the corresponding trigger The output will remain ON until the trigger is deactivated Trigger A activates Output 1 Trigger B activates Output 2 If the Minimum Speed Threshold in the Painting Setup sub menu is NOT set to zero then the output testing function can also be accessed from the normal marking mode operation without having to enter the menu This can be by achieved by simply activating the triggers when the vehicle is stationary speed is zero Edit User Pattern The User Pattern allows the operator to enter customs patterns in the field This function can be accessed through the operating menu For further details see the Pattern Editing section on page 19 enu Clear all patterns Layout wizard Output testing Edit user pattern Autoline 410 Controller User Manual 14 Normal Marking Mode Operation Pattern Cycle Select Patterns cycles
21. t Units Can be set as either distance based or time based ReSync resolution Sets the increment length for the ReSync Cycle function Distance count Configures distance measurement as Pattern or Applied Trigger Offset The Trigger Offset function allows for a distance based offset between when the trigger is activated and when the output is activated This is useful for look ahead triggering where the operator may be triggering from a pointer extended in front of the vehicle and several metres in front of where the guns are positioned The Trigger Offset value will be the distance between the operator s visual triggering point and the position of the guns The Trigger Offset enable allows the offset function to be enabled disabled without having to clear the offset value Trigger pointer Trigger offset 1510 000 Gun 4 offset D Gun B offset 0 000 Timed spot 100 maj Settings for Triggers GunA and GunB are adjustable from the settings menu Output Offsets Global look ahead trigger offset Per pattern fixed offset GunA can deliver Pattern A or Patten A B Gun A rerpatom GOL fixed offset GunB can deliver Pattern B or PatternB A Painting Setup Patterns sequences pattern offset settings Trigger offset 0 000 trigger and gun routing are set from the Gun A offset 0 000 programming utility global offset B Gun B offset 0 000 Timed spot 100 ms The O
22. t that has the potential to develop excessive transient voltages that can cause severe damage to sensitive electronic devices Examples of such events are welding jump starting batteries servicing alternators etc Autoline 410 Controller User Manual 6 Main Operation Menu Access amp Navigation Up Down ON OFF VOO ON OFF e Turn the Autoline controller ON by pressing and releasing the key e Shut down OFF the Autoline controller by pressing and holding the key for 3 seconds Setup Menu Access e Shut down OFF the Autoline controller by pressing and holding the key for 3 seconds e While holding the key down press and release the key to enter the Setup Menu Operating Menu Access e Ensure machine is stationary and Autoline controller is idle e Press the G key to enter Main Menu Menu Navigation e Navigate to the required setting using the Ay keys e Use the m key to select a menu item e Use the A keys to make the adjustments e Press the G key to confirm Press the key to go back Autoline 410 Controller User Manual 7 Setup Menu This menu is where most system settings are configured General Units Sets the measurement units as either Metres or Feet Speed Units Sets the speed Backlight Sets the backlight level of the display Auto power on Enables Disables the automatic power on function Key beep Enables Disables beeping
23. ther deactivate the trigger or press the W key to Stop calibration when the vehicle reaches the end of the calibration distance e Use the G key to save the new calibration value and exit alibratio ew calibration factor 24 9 Pulses per metre sig icancell It is recommended to verify the entered calibration by checking the operation e Example The system should measure a 100m distance if the vehicle travels 100m Input Type The Speed and Trigger inputs can be configured to be compatible with either NPN or PNP open collector signals NPN input type is recommended and the default setting Manual Automatic Input type Autoline 410 Controller User Manual Painting Setup Trigger offset Sets the offset between when the trigger is activated and when the output is activated Output Offsets Sets offsets between outputs to help match material placement on road Useful for matching placement of paint and beads Timed Spot Length Sets duration of time based spots Distance Spot Length Sets length for distance based spots Trigger latch enable Enable Disables the Trigger Latch Mode Display accuracy Sets number of decimal places of speed display Target speed Sets the target speed for the Speed Alarm function Speed margin Sets the speed margin for the Speed Alarm function Minimum speed Sets minimum speed that system will allow marking Line Adjus
24. tomer that the product purchased from Novo Innovation the Product will be free from defects in materials and workmanship under the normal use and service of which the Product was intended for a period of 12 months from the date of purchase of the Product by the Customer The Customer s exclusive remedy under this Limited Warranty shall be the repair or replacement at Novo Innovation Ltd s sole option of the Product or any part of the Product determined by Novo Innovation Ltd to be defective This Limited Warranty does not extend to any Product damaged by reason of alteration accident abuse neglect or misuse or improper or inadequate handling improper or inadequate wiring utilized or installed in connection with the Product installation operation or use of the Product not made in strict accordance with the specifications and written instructions provided by the manufacturer use of the Product for any purpose other than those for which it was intended ordinary wear and tear disasters or Acts of God unauthorized attachments alterations or modifications to the Product the misuse or failure of any item or equipment connected to the Product not supplied by Novo Innovation Ltd improper maintenance or repair of the Product or any other reason or event not caused by Novo Innovation Ltd NOVO INNOVATION LTD HEREBY DISCLAIMS ALL OTHER WARRANTIES WHETHER WRITTEN OR ORAL EXPRESS OR IMPLIED BY LAW OR OTHERWISE INCLUDING WITHOUT LIMITA
25. utput Offset function allows for a distance based offset between when the pattern is activated and when the actual output is activated This is useful for the matched placement of paint and beads Each output has an individual offset setting Example Paint gun on Output 1 Bead gun on Output 2 Physical distance between guns is 500mm Output 1 Offset value Omm Output 2 Offset value 500mm Autoline 410 Controller User Manual 10 Distance Spot Length Timed Spot Length Setting Both these settings set the length of the spot pattern output Distance based spot patterns use the program script element LS Distance based unit is millimetres mm or feet e Time based spot patterns use the program script element S Time based unit is milliseconds ms It is recommended to edit this setting to adjust the spot length rather than using the Line Adjust setting This will maintain the correct Line Adjust setting for the line outputs Refer to the Autoline Pattern Editor Guide for further pattern program details Trigger Latch Mode Latch Mode latches ON the line outputs until the completion of the line pattern if enabled in the pattern program This semi automatic functionality is useful for remark work and multiple line barrier applications During remark work the start of the line output can be triggered by momentarily activating the input trigger The programmed line length will be outputted and stopped automatical
26. when keys are pressed Factory defaults Reverts all setting back to factory defaults Speed Units Metric Options Imperial Options Km h Kilometres per hour Metres h Meteres per hour Miles h Miles per hour Feet h Feet per hour Calibration Manual Performs the manual speed calibration process Automatic Performs the automatic speed calibration process Input type Sets the input type as NPN or PNP Manual Speed Calibration Process This setting allows the speed calibration value to be manually adjusted e Use the Ay keys to make the adjustments e Use the G key to save the adjustment and exit Automatic Speed Calibration Process e Accurately measure and mark out a calibration distance Minimum of 30m 100ft is recommended e Enter the correct calibration distance into the Autoline controller Adjust distance setting if required alibration 5 Metres Use the Ay keys to make the adjustments Use the G key to continue Continued on next page Autoline 410 Controller User Manual Automatic Speed Calibration Process Continued e Position vehicle at the start of the calibration distance marked on the road e Either activate a trigger or press the G key to Start calibration e Drive the calibration distance The pulse count will increase as the vehicle travels alibratio Drive 50 Metres Pulses counted 4310 Cancel e Ei
27. wo spots at typical marking speed e Check spot length of second spot The first line is not used for checking in case there is a blockage in the gun etc e Adjust spot length setting as required Set Trigger and Output Offsets if applicable Set required offset values Mark some line output Check line application to ensure offset value set is correct Adjust and re check where necessary Autoline 410 Controller User Manual 18 Pattern Editing It is possible to edit add or remove paiterns by using either the PC based Pattern Editor program or the built in pattern editing function PC Based Pattern Editor Program Introduction The PC based Pattern Editor program can generate and save pattern files These files can then be loaded onto the Autoline controller via the Autoline USB cable connected to a PC The Pattern Editor can also be used as a means of updating the software in the Autoline unit Operation The VX10 Pattern Editor has the following capabilities Generate new or modify existing pattern files Create line patterns using the pattern programming elements e g L3G9C Configure trigger inputs Configure outputs Enable trigger latching Update Autoline software Refer to the Autoline Pattern Editor Guide for further information Built In User Pattern Function The User Pattern allows the operator to enter customs patterns in the field This function can be accessed through the op
Download Pdf Manuals
Related Search