Gentex-710LS 550-0060
Contents
1. aa ee eS z Lea Room DR Figure 1 A SMOKE ALARM SHOULD BE LOCATED BETWEEN THE SLEEPING AREA AND THE REST OF THE FAMILY LIVING UNIT In family living units with more than one bedroom area or with bedrooms on more than one floor more than one smoke alarm will be needed as shown in Figure 2 Brine T anen Bedroom TWReem pom y tuea Beceem Besom Figure 2 IN FAMILY LIVING UNITS WITH MORE THAN ONE SLEEPING AREA A SMOKE ALARM SHOULD BE PROVIDED TO PROTECT EACH SLEEPING AREA IN ADDITION FIGURE 2 SHOWS REQUIRED ALARMS IN EACH BEDROOM FOR NEW CONSTRUCTION In addition to smoke alarms outside of the sleeping areas NFPA 72 requires the installation of a smoke alarm on each additional story of the family living unit including the basement These installations are shown in Figure 3 The living area smoke alarms should be installed in the living room or near the stairway to the upper level or in both locations The basement smoke alarm should be installed in close proximity to the stairway leading to the floor above The alarm should be positioned relative to the stairway so as to intercept smoke coming from a fire in the basement before the smoke enters the stairway Bedroom nan Bedroom eg Dining Reem Room Figure 3 A SMOKE ALARM SHOULD BE LOCATED ON EACH STORY Where to Locate the Required Smoke Alarms in New Construction All of the smoke2. LR DETECTOR DOES NOT SEE ene fe TEST EACH SMOKE eon fender MAINTENANCE After your smoke alarm has been in operation for a period of time or if it was installed prior to the completion of all building construction your smoke alarm may have become more sensitive due to dirt build up in the smoke alarm s optic sensing chamber which could cause nuisance alarms or could cause activation from small amounts of smoke build up If this should occur following this simple washing procedure will restore your smoke alarm back to its original condition For further information regarding frequency of cleaning and testing refer to NFPA 72 NFPA Batterymarch Park Quincy MA 02269 IMPORTANT Failure to follow full cleaning instructions could result in damage to this smoke alarm DO NOT remove all alarms at the same time for cleaning 1 Unplug the electrical power cord to the smoke alarm 2 Twist the smoke alarm counter clockwise to remove it from its mounting plate Select three 3 standard size wash buckets and fill them each with one gallon of normal tap water distilled or de ionized treated water is recommended as a final rinse if water is extremely hard in your area 4 Add 1 8 cup of Ivory dishwashing liquid to the first bucket of water and allow it to mix thoroughly then place one dirty smoke alarm into the soap water mixture until it becomes completely covered or submerged NOTE If the smoke alarms are exceptionally dirt
3. alarms specified for existing construction are required and in addition a smoke alarm is required in each bedroom Are More Smoke Detectors Desirable The required number of smoke alarms may not provide reliable early waming protection for those areas separated by a door from the areas protected by the required smoke alarms For this reason it is recommended that the householder consider the use of additional smoke alarms for those areas for increased protection The additional areas include basement bedrooms dining room near furnace room utility room and hallways not protected by the required smoke alarms The installation of smoke alarms in kitchens attics finished or unfinished or garages is not normally recommended as these locations occasionally experience conditions that can result in improper operation IMPORTANT CONSIDERATION We recommend replacing your alarm s every ten 10 years why Dust dirt and other environmental contaminants can affect your alarm over a prolonged period Fast changing industry consensus standards and codes on all alarms make it advisable to periodically upgrade your alarm to maximize life safety Assurance that your smoke alarm needs are kept abreast with the constantly improving electronic technology Smoke alarms are recognized as one of the lowest cost ways to protect dwelling inhabitants against the danger of fire s It makes good common sense to periodically replace and up
4. from fires and about preparing your family s escape plans NOTE Current studies have shown smoke alarms may not awaken all sleeping individuals and that it is the responsibility of individuals in the household that are capable of assisting others to provide assistance to those who many not be awakened by the alarm sound or to those who may be incapable of safely evacuating the area unassisted WHAT THIS SMOKE ALARM CAN DO This smoke alarm is designed to sense smoke entering its sensing chamber The smoke alarm does not sense gas heat or flames When properly located installed and maintained this smoke alarm is designed to provide early warning of developing fires at a reasonable cost This smoke alarm monitors the air and when it senses smoke activates its built in alarm horn It can provide precious time for you and your family to escape from your residence before a fire spreads Such an early warning however is possible only if the smoke alarm is located installed and maintained as specified in this User s Manual NOTE This smoke alarm is designed for use within single residential living units only that is it should be used inside a single family home or one apartment of a multi family building In a multi family building the smoke alarm may not provide early warning for residents if it is placed outside of the residential units such as on outside porches in corridors lobbies basements or in other apartments In
5. to permit optimum smoke entry from any direction while rejecting light from outside the smoke alarm The light source is an infrared invisible LED which pulses every 8 seconds The light sensor is a photodiode matched to the light frequency of the LED light source Under normal conditions the light generated by the pulsing infrared LED is not seen by the light sensor as it is positioned out of the direct path of the light beam When smoke enters the sensing chamber light from the pulsing LED light source is reflected by the smoke particles onto the photodiode light sensor At the first sighting of smoke the smoke alarm is put into a pre alarm mode This is indicated by a rapidly flashing LED on the face of the smoke alarm Once the light sensor confirms smoke for 2 consecutive pulses inside the chamber the light sensor produces the signal necessary to trigger the alarm This technique of verifying the smoke condition combined with a 5 to 1 signal to noise ratio substantially reduces the possibility of nuisance alarms HOW TO TELL IF YOUR SMOKE ALARM IS WORKING PROPERLY Your smoke alarm is provided with an alarm horn and pulsating Light Emitting indicator Diode which pulses every 15 30 seconds and a green AC power on LED When turning the test knob on the alarm to TEST 1 the red LED will rapidly flash the horn will sound and the strobe light will flash If AC power fails the green LED will turn off The test knob on you
6. 2 Determine proper location for smoke alarm above a receptacle that is NOT CONTROLLED BY AN ON OFF SWITCH 3 If screw anchors are used drill two 3 16 holes insert the screw anchors and mount the plate to wall using the supplied screws 4 Mount the smoke alarm as illustrated in Figure 7 5 Use the enclosed cord retainer clamp as illustrated in Figure 6 to insure the unit is not accidentally disconnected Place the smoke alarm up to the mounting plate rotating it to about 10 00 o clock then rotate it clockwise to 12 00 It should snap lock firmly into place Keep the smoke alarm parallel to the mounting plate so upper and lower tabs on the plate seat into the smoke alarm Figure 7 TobMBTPgETON IMPORTANT WARNING Failure to observe any of the conditions set forth may cause system malfunction and damage to the smoke alarm CHECKOUT amp TROUBLESHOOTING Turn test knob to the NORMAL position and supply house power to the smoke alarm The red indicator should flash every 30 seconds showing that the smoke alarm is operating properly 2 If red light is not flashing or the green LED is not on a Check the house current b Check to see if the plug is in the outlet Ifthe power and wiring check out but the red light does not flash return the alarm to the manufacturer See TO RETURN A SMOKE ALARM 3 Testing with the Test Knob a Rotate the test knob counter clockwise to the TEST 1 Position and wait up
7. Do not leave small children home alone c Develop a family escape plan and practice it with your entire family especially small children Draw a floor plan of your home and find two ways to exit from each room There should be one way to get out of each bedroom without opening the door Pg 7 1 550 0060 Teach children what the smoke alarm signal means and that they must be prepared to leave the residence by themselves if necessary Show them how to check to see if doors are hot before opening them how to stay close to the floor and crawl if necessary and how to use the alternate exit if the door is hot and should not be opened Decide on a meeting place a safe distance from your house and make sure that all your children understand that they should go and wait for you if there is a fire Hold fire drills at least every 6 months to make sure that everyone even small children know what to do to escape safely Know where to go to call the fire department from out side your residence Provide emergency equipment such as fire extinguishers and teach your family to use this equipment properly d Bedroom doors should be closed while sleeping if a smoke alarm is installed in the bedroom They act as a barrier against heat and smoke e Establish an escape plan Post a detailed floor plan depicting the chosen escape routes Each bedroom should have at least two escape routes Make sure your children know what to do in case of f
8. GENTEX CORPORATION A Smarter Vision 710LS 713LS PHOTOELECTRIC TYPE SMOKE ALARMS AC POWERED 120V 60Hz Installation Instructions Owner s User s Information Manual READ CAREFULLY AND SAVE INTRODUCTION The 713LS Smoke Alarm is a Photoelectric Type Smoke Alarm for use as an evacuation device in residential applications while the 710LS is for use as an alert and relocate device Each smoke alarm has a solid state piezo signal to warn and alert the household to the presence of threatening smoke Your photoelectric smoke alarm is designed to detect the smoke that results from an actual fire Consequently it is uncommon for household smoke such as cigarette smoke or normal cooking smoke to cause an alarm MODEL NO DESCRIPTION 710LS 120 VAC Wall Mounted Provided With a 9 ft Line Cord Pulsating Horn 713LS Same as 710LS but with a Temporal Horn This unit produces a non temporal audible alarm and is therefore not intended for locations where the desired action of the occupant s is evacuation NOTE Loss of electrical input will cause the smoke alarm not to function For maximum safety you should install both battery operated and AC powered smoke alarms HOW YOUR SMOKE ALARM WORKS The 710LS 713LS Smoke Alarm operates on the photoelectric light scatter principle The unit s sensing chamber houses a light source and a light sensor The darkened sensing chamber is exposed to the atmosphere and designed
9. SPECIFIED ABOVE PLEASE NOTE THAT SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMBLIED WARRANTY LASTS SO FHE ABOVE EXCLUSION MAY NOT APPLY TO YOU LIMITED WARRANTY GENTEX WILL NOT BE LIABLE FOR ANY LOSS DAMAGE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING IN CONNECTION WITH THE SALE USE OR REPAIR OF THIS SMOKE ALARM PLEASE NOTE THAT SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLU Sian MAY NOT APPLY TO YOU madia dealin workmanstip materiais or constuction shoud cause your Smoke Alan o come naperabie wihin ihe warranty parod you must retum the Smaka Alarm 1o Gentex postage ad Yeu ust aiso pack he Smoke Alarh Ye minimize the rsx Of I being damaged In ara Got mus aiso enclose a retum adres Gmoke Aarne returned ts mamani sere shoud be sent 1o Gentex Corporation 10485 Chicago Drive Zeeland Mil Sadbe iin rect a Smoka Alarm ne damaged coriton aa The result of shipping we wil notify you Sis LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE yea pene ta tt ek han orphan ae a We GENTEX CORPORATION 550 0060 13 10985 CHICAGO DRIVE ZEELAND MI 49464 PHONE 1 800 436 8391 wurw gentex com FP_RMA gentex com 9 1 87 Pg 7 5
10. ance alarms are caused by placing alarms where they will not operate properly To avoid nuisance alarms do not Place alarms In or near areas where combustion particles are normally present such as kitchens in garages where there are particles of combustion in vehicle exhausts near furnaces hot water heaters or gas space heaters Install smoke alarms at least 20 feet 6 meters away from kitchens and other areas where combustion particles are normally present In air streams passing by kitchens Figure 5 shows how a smoke alarm can be exposed to combustion particles in normal air movement paths and how to correct this situation mef ay Smo pe sxacom tg Room Figure 5 In damp or very humid areas or next to bathrooms with showers The moisture in humid air can enter the sensing chamber as water vapor then cool and condense into droplets that cause a nuisance alarm Install smoke alarms at least 10 feet 3 meters away from bathrooms In very cold or very hot environments or in unheated buildings or outdoor rooms where the temperature can go below or above the operating range of the alarm Temperature limits for proper operation are 40 to 100 F 4 4 to 37 8 C In very dusty or dirty areas Dust and dirt can build up on the smoke alarms sensing chamber and can make it overly sensitive or block openings to the sensing chamber and keep the smoke alarm from sensing smoke Near fresh air inlets or returns or
11. date your smoke alarm that contributes so much to life safety MOUNTING LOCATION Wall location locate the top of the alarm at least 4 inches and not more than 12 inches from the ceiling Observe alarm for proper top bottom orientation test knob is near bottom of unit x Soa swore ees Nt EEA LETS vest Locanion Figure 4 RECOMMENDED SMOKE ALARM MOUNTING LOCATION WHERE SMOKE ALARMS SHOULD BE PUT IN MOBILE HOMES In mobile homes built after about 1978 that were designed and insulated to be energy efficient smoke alarms should be installed as described in the section above In older mobile homes that have little or no insulation compared to today s standards uninsulated metal outside walls and roofs can transfer heat and cold from outdoors making the air right next to them hotter or colder than the rest of the inside air These layers of hotter or colder air can prevent smoke from reaching a smoke alarm Therefore put smoke alarms in such units only on inside walls between 4 and 12 inches 10 and 30 cm from the ceiling If you are not sure about the insulation level in your mobile home or if you notice that the walls or ceiling are unusually hot or cold put the alarm on an inside wall Minimum protection requires one alarm as close to the sleeping area as possible For better protection put one alarm in each room but first read the Locations to Avoid Pg 7 3 550 0060 LOCATIONS TO AVOID Nuis
12. er to NFPA 101 The Life Safety Code and NFPA 72 for smoke alarm requirements for fire protection in buildings not defined as households Installing smoke alarms may make you eligible for lower insurance rates but smoke alarms are not a substitute for insurance Home owners and renters should continue to insure their lives and property PLACEMENT OF SMOKE ALARMS THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION S STANDARD 72 National Fire Protection Association Batterymarch Park Quincy MA 02269 Pg 7 2 550 0060 For your information the National Fire Protection Association s Standard 72 reads as follows Smoke detectors shall be installed outside of each separate sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit including basements and excluding crawl spaces and unfinished attics In new construction a smoke detector shall be installed in each sleeping room Where to Locate the Required Smoke Detectors in Existing Construction The major threat from fire in a family living unit is at night when everyone is asleep The principal threat to persons in sleeping areas comes from fires in the remainder of the unit therefore a smoke alarm s is best located between the bedroom areas and the rest of the unit In units with only one bedroom area on one floor the smoke alarms should be located as shown in Figure 1
13. excessively drafty areas Air conditioners heaters fans and fresh air intakes and returns can drive smoke away from smoke alarms making the smoke alarms less effective In dead air spaces at the top of a peaked roof or in the corners between ceilings and walls Dead air may prevent smoke from reaching the smoke alarm In insect infested areas If insects enter a smoke alarm s sensing chamber they may cause a nuisance alarm Get rid of the bugs before installing alarms where bugs are a problem Near fluorescent light fixtures Electrical noise from nearby fluorescent light fixtures may cause a nuisance alarm Install smoke alarms and fluorescent lights on separate electrical circuits WARNING Never disconnect an AC alarm to silence a nuisance alarm Open a window or fan the air around the alarm to remove the smoke The alarm will automatically turn off when the smoke in the air is completely gone Do not stand close to the alarm The sound produced by the alarm is loud because it is designed to awaken you in an emergency Prolonged exposure to the horn at a close distance may be harmful to your hearing MOUNTING PLATE amp ALARM LINE CORD MODEL 710LS 713LS The 710LS 713LS is supplied with a 9 foot line cord for installation to a normal outlet box For this type of installation 1 Care should be taken to lace cord through slots in base as show in in Figure 6 to insure cord does not interfere with engagement of the mounting bracket
14. from its mounting plate 3 Carefully pack the manufacturer cannot be responsible for consequential damage and return to the manufacturer Include complete details as to exact nature of difficulties being experienced and date of installation 4 Return to Gentex Corporation 10985 Chicago Drive Zeeland Michigan 49464 Prior to returning call Gentex at 1 800 436 8391 or e mail FP_RMA gentex com to obtain a RMA Number from our return department For a period of 12 months trom the date of purchase or a maximum of 18 months from the date of manufacture Genter warrants fo you Ine original consumer purchaser thal your Smoke Alarm wil be fee ron detects in workmanship mato and cotton under normal use and Service It a detect in workmanship matenas eonsrucion should cause your Smoke Alarm fo Become inperasie ini ine warranty period Gentex ns repair yout Smoke Alarm or amish ou Wha new Gr rebu replacement Smoke Alar whau charge 10 you except fr postage Teated io retum the Smoke Alarm fo us Your repairs ar replacement Smoke Alarm will be reiumed to Youttee o charge and wil be covered unger Pes waranty forthe Balance of ine warranty period TS mara fo ingpecton ol your sgt Am shone Pat he damage ore Imatlenence or epaiz other ihan nose perlormed bY us gs ANY WARRANTIES IIBLIED UNDER ANY STATE LAW INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLY ONLY FOR THE WARRANTY PERIOD
15. ire and teach them to follow the escape plan you have posted Agree on an outside meeting place Conduct fire drills at least twice a year Be sure each member of the family is familiar with the smoke alarm so they can react properly WHAT TO DO IF THERE IS A FIRE IN YOUR HOME If you have prepared family escape plans and practiced them with your family you have increased their chances of escaping safely Review the following rules with your children when you have fire drills so everyone will remember them in a real fire emergency If smoke alarm should sound a Don t panic stay calm Your safe escape may depend on thinking clearly and remembering what you have practiced b Get out of the house following a planned escape route as quickly as possible Do not stop to collect anything or to get dressed c Open doors carefully only after feeling to see if they are hot Do not open a door if itis hot use an alternate escape route d Stay close to the floor smoke and hot gases rise e Cover your nose and mouth with a cloth wet if possible and take short shallow breaths f Keep doors and windows closed unless you open them to escape g Meet at your prearranged meeting place after leaving the house h Call the Fire Department as soon as possible from outside your house Give the address and your name i _ Never re enter a burning building Contact your local Fire Department for more information on making your home safer
16. multi family buildings each residential unit should have alarms to alert the residents of that unit Smoke alarms designed to be interconnected should be interconnected within one family residence only otherwise nuisance alarms will occur when an alarm in another living unit is tested IMPORTANT NOTE WHAT SMOKE ALARMS CANNOT DO Smoke alarms will not work without power Battery operated smoke alarms will not work without batteries with dead batteries or if the batteries are not installed properly AC powered smoke alarms will not work if their AC power supply is cut off by an electrical fire an open fuse or circuit breaker or for any other reason If you are concerned about the reliability of either the batteries or your AC power supply for any of the above reasons you should install both battery and AC powered alarms for maximum safety Smoke alarms may not sense fire that starts where smoke cannot reach the alarms such as in chimneys in walls on roofs or on the other side of closed doors If bedroom doors are usually closed at night smoke alarms should be placed in each bedroom as well as in the common hallway between them Smoke alarms also may not sense a fire on another level of a residence or building For example a second floor smoke alarm may not sense a first floor or basement fire Therefore smoke alarms should be placed on every level of a residence or building The horn in your smoke alarm meets or exceeds curre
17. nt audibility requirements of Underwriters Laboratories However if the smoke alarm is located outside a bedroom it may not wake up a sound sleeper especially if the bedroom door is closed or only partly open If the smoke alarm is located on a different level of the residence than the bedroom it is even less likely to wake up people sleeping in the bedroom In such cases the National Fire Protection Association recommends that the smoke alarms be interconnected so that an alarm on any level of the residence will sound an alarm loud enough to awaken sleepers in closed bedrooms This can be done by installing a fire detection system by connecting alarms together or by using radio frequency transmitters and receivers All types of smoke alarm sensors have limitations No type of smoke alarm can sense every kind of fire every time In general smoke alarms may not always warn you about fires caused by violent explosions escaping gas improper storage of flammable materials or arson NOTE This smoke alarm is not designed to replace special purpose fire detection and alarm systems necessary to protect persons and property in non residential buildings such as warehouses or other large industrial or commercial buildings It alone is not a suitable substitute for complete fire detection systems designed to protect individuals in hotels and motels dormitories hospitals or other health and supervisory care and retirement institutions Please ref
18. r smoke alarm simulates actual smoke conditions FIRE PROTECTION PLAN WHAT YOU CAN DO TO MAKE YOUR FAMILY SAFE FROM FIRES This smoke alarm can quickly alert you to the presence of smoke it cannot prevent fire The ultimate responsibility for fire protection rests solely on you Installing smoke alarms is just the first step in protecting your family from fires You also must reduce the chances that fires will start in your home and increase your chances of safely escaping if one does start To have an effective fire safety program a Install smoke alarms properly following the instruction this manual Keep your smoke alarms clean Test your smoke alarm weekly and repair or replace it when it no longer functions As with any electronic product alarms have a limited life and alarms that don t work cannot protect you b Follow safety rules and prevent hazardous situations Use smoking materials properly never smoke in bed Keep matches and cigarette lighters away from children Store flammable materials in proper containers and never use them near open flames or sparks Keep electrical appliances and cords in good working order and do not overload electrical circuits Keep stoves fireplaces chimneys and barbecue grills grease free and make sure they are properly installed away from combustible materials Keep portable heaters and open flames such as candles away from combustible materials Do not allow rubbish to accumulate
19. to 20 seconds for the smoke alarm to sound If the smoke alarm does not sound after 20 seconds return the smoke alarm for service b After successfully testing smoke alarm return test knob to NORMAL non test position and wait 20 seconds for the smoke alarm to stop sounding c To test smoke alarm for high sensitivity turn test knob clockwise to test position 2 Smoke alarm should remain silent Return knob back to the normal position If your smoke alarm sounds during this test it means the smoke alarm s sensitivity has become too high and may cause false alarms This could mean your smoke alarm is dirty and should be cleaned as described in the maintenance procedure below If the smoke alarm continues to alarm for TEST 2 position following cleaning return it to Gentex for service d To check for proper smoke entry into your smoke alarm s sensing chamber Gentex recommends using the Home Safeguard Smoke Detector spray This test should be performed once a year and should be sprayed from a distance no closer than 12 inches from smoke alarm Pg 7 4 550 0060 IMPORTANT The test knob is not an electrical switch nor is it connected in any way to the alarm Therefore when you test with the test knob you are actually simulating a smoke condition in the alarm as well as testing the sensitivity of the photodiode and the circuit between the photodiode and the alarm TEST KNOB IN NORMAL NOT TEST POSITION PHOTODIODE INFRARED
20. u have any questions please contact Gentex Corporation or your local Gentex distributor WARNING If the smoke alarm does not work properly do not try and fix it yourself This will void your warranty See To Return A Smoke Alarm for instructions to return smoke alarms that do not operate properly DO NOT TRY TO FIX IT YOURSELF IMPORTANT Gentex recommends smoke alarms be tested a minimum of once a week WARNING Never use an open flame of any kind to test your smoke alarm You may ignite and damage the smoke alarm as well as your home The test feature of your smoke alarm accurately simulates smoke conditions and tests the smoke alarm s functions as required by Underwriters Laboratories WARNING Do not cover tape or otherwise block the openings of your smoke alarm These openings are designed to allow air to pass through your smoke alarm thus sampling the air around the alarm WARNING Smoke alarms are not to be used with detector guards unless the combination has been evaluated and found suitable for that purpose FAILURE TO REGULARLY CLEAN THIS SMOKE ALARM WILL RESULT IN FALSE ALARMS A BUILD UP OF DUST CREATES AN OBSCURATION THAT SIMULATES SMOKE THIS MEANS THE UNIT WILL GO INTO ALARM WITHOUT A FIRE CONDITION TO RETURN A SMOKE ALARM Should you experience problems with your smoke alarm proceed as follows 1 Unplug the electrical power cord to the smoke alarm 2 Twist the smoke alarm counter clockwise to remove it
21. y you may wish to first wipe off any excess dirt before washing smoke alarm so as not to dirty the wash water too quickly DO NOT open smoke alarm for cleaning IF SMOKE ALARM IS OPENED DURING CLEANING PRODUCT WARRANTY BECOMES VOID WARNING ONLY IVORY DISHWASHING LIQUID IS TO BE USED OTHER BRANDS ARE NOT RECOMMENDED AND MAY CAUSE YOUR SMOKE ALARM TO MALFUNCTION Allow smoke alarm to soak for approximately 10 minutes longer if extremely dirty Then agitate for 5 or 10 seconds to flush out any remaining dirt left inside smoke alarm s housing 6 Remove smoke alarm from wash water and transfer directly to one of the first rinse buckets containing clear water Again allow smoke alarm to become completely submerged agitate once more for 5 or 10 seconds to remove soap residue 7 Finally transfer smoke alarm to your second and final rinse bucket repeating method found in Step 6 then remove smoke alarm to a clean dry area for a period of 48 hours to allow it to thoroughly dry WARNING SMOKE ALARMS ARE TO BE AIR DRIED ONLY DO NOT PLACE SMOKE ALARM IN OVEN MICROWAVE OR USE A HOT AIR BLOWER TO ACCELERATE DRYING TIME THIS COULD RESULT IN DAMAGE TO YOUR SMOKE ALARM IMPORTANT IT IS RECOMMENDED TO CHANGE WASH AND RINSE WATER AFTER FIVE 5 SMOKE ALARMS IF YOUR SMOKE ALARMS ARE EXTREMELY DIRTY WATER SHOULD BE CHANGED MORE FREQUENTLY In the event you experience difficulty in the cleaning of your smoke alarm or if yo
Download Pdf Manuals
Related Search