F4X5 Indoor Series Network Camera User`s Manual
Contents
1. Working Period gt Alarm Di Alarm Anti Dither 1 Second 0 100 Video Masking gt Abnormity Storage Record Channel System Record Delay 10 Second C 10 300 Information Relay out Alarm Delay 10 Second 10 300 C Send E Mail O pr Activation None Address 0 Snapshot Figure 4 23 AWatch Eis Network Event gt Alarm gt Abnormity Storage System information a lo ie Figure 4 24 Please refer to the following sheet for detailed information You need to check the box to enable this function 38 Parameter Function Sensitivity There are six levels The sixth level has the highest sensitivity Area e There are six levels The sixth level has the highest sensitivity e Region you can click this button to set Video masking zone The interface is shown as in Figure 4 24 There are PAL 22X18 NTSC 22X15 zones Right click mouse you can go to full screen display mode Do remember clicking OK button to save your Video masking zone setup Working e Video masking function becomes activated in the specified Period periods e There are six periods in one day Please draw a circle to enable corresponding period e Select date If you do not select current setup applies to today only You can select all week column to apply to the whole week e Click OK button system goes back to motion detection interface please click save button to exit Anti dither System only mem2. gt Multicast gt WIFI gt aos Event Storage System Information Figure 4 15 4 2 10 Multicast The multicast interface is shown as in Figure 4 16 Multicast is a transmission mode of data packet When there is multiple host to receive the same data packet multiple cast is the best option to reduce the broad width and the CPU load The source host 30 can just send out one data to transit This function also depends on the relationship of the group member and group of the outer Here you can set multicast address and port You also need to go to Live interface to set the protocol as Multicast Watch NEI Camera Multicast Network gt TCP IP Multicast Address 239 255 42 42 Pot 36666 1025 65535 gt Connection PPPOE gt DDNS gt IP Filter gt SMTP E mail gt UPnP gt SNMP gt Bonjour gt gt WIFI gt aos Event Storage System Information Figure 4 16 4 2 11 WIFI Please note this function is for the device of WIFI module The WIFI interface is shown as in Figure 4 17 31 Camera Network gt TCP IP gt Connection Connect mode Encryption Mode Signal Quality gt PPPoE gt DDNS gt IP Filter gt SMTP E mail gt UPnP gt SNMP gt Bonjour gt Multicast WIFI INFO gt Current Hot Spot gt Q08 Event IP address Storage Subnetmask System Default IP Gateway Information Figure 4 17 Please check the
3. Figure 4 43 Add group It is to add group and set its corresponding rights See Figure 4 45 Please input the group name and then check the box to select the corresponding rights lt includes shutdown reboot device live view record control PTZ control and etc Watch NEI Camera Account Network User Name Group Event i ey eee a Add Group System Group gt General Remark gt Authority List O All C Shutdown Reboot Default C Live gt PTZ C Record control O HDD FIPTZ Save Cancel Record control Backup PTZ Account Import Export Auto Maintain Upgrade Information Authority List Shutdown Reboot Live Log Search Clear Log Network Alarm Add Group Relay infout System Update Auto Maintain General Setting Encode Record RS232 Video Detect PFE Default Video Input Figure 4 44 53 Modify group Click the modify group button you can see an interface is shown as in Figure 4 45 Here you can modify group information such as remarks and rights WatchiNEi Camera Account Network User Name Event Modify Group Storage System erin gt General Remark gt Authority List gt PTZ gt Default gt ImportExport gt Auto Maintain gt Upgrade Information Authority List Shutdown Reboot Live Log Search Clear Log Network Alarm Add Group 4 5 3 PTZ Please note some series product does not support this function The PTZ interface is shown as in Figure 4 46 Watch
4. Information Remote Path Figure 4 36 4 4 3 Record control The record control interface is shown as in Figure 4 37 WatchWEI CT A Serup TA Camera Conditions Network Pack Duration 8 Minute 1 120 Event Pre event Record 1 Second 0 30 Storage Disk Full Overwrite gt Schedule Record Mode Automatic Manual Off gt Destination System Information Figure 4 37 Please refer to the following sheet for detailed information Parameter Function Pack Here you can select file size Default setup is 8 minutes Duration Pre record Please input pre record value here For example system can record the four seconds video in the buffer The record begins from the fifth second 47 Disk Full There are two options stop recording or overwrite the previous files when HDD is full e Stop Current working HDD is overwriting or current HDD is full it will stop record e Overwrite Current working HDD is full it will overwrite the previous file Record There are three modes Auto manual close mode 4 5 System 4 5 1 General The general interface includes the local host setup and the date time setup 4 5 1 1 Local host The local host interface is shown as in Figure 4 38 Watch NEJ Camera General Date amp Time Network Device Name TZ01CWV 15200022 Event Language English x Storage e xj Video Standard PAL System E gt Account gt PT
5. Figure 4 31 Please refer to the following sheet for detailed information 43 Parameter Function Event e The abnormal events include no disk no space disk error net error Type offline IP conflict e Threshold You can set the minimum percentage value here The device can alarm when capacity is not sufficient e You need to draw a circle to enable this function Record system auto activates channel to record once alarm occurs For offline type only See Figure 4 31 You need to check the box to enable this function Record System can delay the record for specified time after alarm ended The Delay value ranges from 10s to 300s Relay Out The corresponding alarm output channel when alarm occurs You need to check the box to enable this function Some series product does not support this function Relay out The alarm output can delay for the specified time after alarm stops The Delay value ranges from 10s to 300s Some series product does not support this function If you enable this function system can send out email to alarm the specified user This function is invalid when network is offline or IP conflict occurs 4 4 Storage 4 4 1 Record schedule and snapshot schedule In these two interfaces you can add or remove the schedule record snapshot setup See Figure 4 32 There are three record modes general auto motion detect and alarm There are six periods in one day Please make sure you have enab
6. 4 1 3 Audio Please note some series product does not support this function The audio interface is shown as below See Figure 4 6 18 Watch NE Camera Audio gt Conditions Main Stream Sub Stream gt Video Enable O Enable Network Encode Mode G 711A x Encode Mode G T11A Event Storage System Information Figure 4 6 Please refer to the following sheet for detailed information Parameter Function Audio enable Main stream Recorded file only contains video by default You need to check the audio box here to enable audio function Sub Extra stream Recorded file only contains video by default You need to check the audio box here to enable audio function Encode mode The encode mode of the main stream and extra stream include PCM G 711A and G 711Mu The setup here is for audio encode mode and the bidirectional talk encode both 4 2 Network 4 2 1 TCP IP The TCP IP interface is shown as in Figure 4 7 19 Watch NEJ Camera Network gt gt Connection 3 Wire DEFAULT Setas Default gt PPPoE Ethernet Card gt DONS Mode Static DHCP MAC Address Host Name DYR gt IP Filter gt SMTP E mail IP Version IPV4 gt UPnP IP Address 10 15 gt SNMP Subnet mask 255 255 gt Bonjour Default Gateway 10 15 gt Multicast E Preferred DNS Server 8 B y gt QoS Alternate DNS Server BS B Event Enable ARP Ping to set IP address service
7. Thursday Friday C Saturday Period 1 00 00 00 24 00 00 C Period 2 00 00 00 24 00 00 C Period 3 00 00 00 24 00 00 C Period 4 00 00 00 24 00 00 C Period 5 00 00 00 24 00 00 C Period 6 00 00 00 24 00 00 Figure 4 21 35 Watch NE Camera Area Network Event gt Alarm gt Abnormity Storage System Information 0009000500100 050 5009000500 IAM Figure 4 22 Please refer to the following sheet for detailed information You need to check the box to enable motion detection function Sensitivity There are six levels The sixth level has the highest sensitivity Region e There are six levels The sixth level has the highest sensitivity e Region If you select motion detection type you can click this button to set motion detection zone The interface is shown as in Figure 4 22 There are PAL 22X18 NTSC 22X15 zones Right click mouse you can go to full screen display mode Do remember clicking OK button to save your motion detection zone setup Working e Motion detection function becomes activated in the specified Period periods See Figure 4 21 e There are six periods in one day Please draw a circle to enable corresponding period e Select date If you do not select current setup applies to today only You can select all week column to apply to the whole week e Click OK button system goes back to motion detection interface please click save button to e
8. 33 Watch NEN Camera Network Realtime Monitor 0 0 53 gt TCPIIP Command 0 0 63 gt Connection gt DONS gt IP Filter gt SMTP E mail gt UPnP gt SNMP gt Bonjour gt Multicast gt WIFI gt Event Storage System Information Figure 4 19 Please refer to the following sheet for detailed information Parameter Function Real time The value ranges from 0 to 63 The router or the switcher can monitor provide different service for various data packets Command The value ranges from 0 to 63 The router or the switcher can provide different service for various data packets 4 3 Event 4 3 1 Video detect 4 3 1 1 Motion Detect The motion detect interface is shown as in Figure 4 20 34 Watch NEJ Camera Motion Detect Network ENE Cl Enable Video Masking m Working Period gt Alarm gt Abnormity Aoa Anti Dither O Second 0 1003 sensitivity 3 e Storage System Record Channel Information Record Delay 10 Second 10 300 Relay out Alarm Delay 10 Second 10 300 LJ Send E Mail O PZ Activation None Address 0 Snapshot Figure 4 20 WatchNEN Camera Working Period Network 0 Sunday Event gt Monday gt Alarm Tuesday gt Abnormity Wednesday Storage Thursday System i Friday AAA Information Saturday AAA AA Setup All Sunday Monday Tuesday Wednesday C
9. Audio to set bidirectional talk mode Some series product does not support this function 2 6 Video Window Setup The interface is shown as in Figure 2 8 Figure 2 8 Video Window Setup Please refer to the following sheet for detailed information 1 Image Click it to open picture setup interface See Figure 2 9 This control interface is on the top right pane 2 Original Click this button to go to original size It is to display the actual size size of the video stream lt depends on the resolution of the bit stream 3 Full screen Click it to go to full screen mode Double click the mouse or click the Esc button to exit the full screen 4 Width and Click it to restore original ratio or suitable window height ratio The picture setup interface is shown as in Figure 2 9 image Adjustment Figure 2 9 Please refer to the following sheet for detailed information setup brightness e All the operations here a es Please go to Setup It is to adjust monitor video gt Camera gt Conditions saturation to adjust o corresponding items It is to adjust monitor video hue Reset Restore brightness contrastness saturation and hue to system default setup 3 PTZ Control Please note some series product does not support this function Before PTZ operation please make sure you have properly set PTZ protocol Please go to Setup gt System gt PTZ to set Here you can view direction keys speed zoom focus
10. Relay Activation Network Event CL Enable gt video Detect Relay in Alarm Working Period ele Anti Dither 0 Second 0 100 SensorType NO y Storage System Record Channel Information Record Delay 10 Second 10 300 3 Relay out Alarm Delay 10 Second 10 300 O Send E Mail ETZ Activation None v Address 0 Snapshot Figure 4 25 Please refer to the following sheet for detailed information You need to check the box to enable this function Working e This function becomes activated in the specified periods Period e here are six periods in one day Please draw a circle to enable corresponding period e Select date If you do not select current setup applies to today only You can select all week column to apply to the whole week e Click OK button system goes back to motion detection interface please click save button to exit Anti dither System only memorizes one event during the anti dither period The value ranges from Os to 100s Sensor type There are two options NO NC 40 Parameter Function Relay out e There is 1 channel alarm output e Corresponding to motion detection alarm output port e Enable alarm activation function You need to select alarm output port so that system can activate corresponding alarm device when alarm occurs Alarm Delay System can delay the alarm output for specified time after alarm ended The value ranges from 10s to 300s Record System auto acti
11. Storage System Information Figure 4 7 Please refer to the following sheet for detailed information Parameter Function Host Name It is to set current host device name lt max supports 32 digit character Ethernet Card Please select the Ethernet port It is for the wire LAN by default Please note for the W series product it has the wireless network card and you can modify the default Ethernet port setup Please note the device needs to reboot to activate the new setup once you modify the default setup Mode There are two modes static mode and the DHCP mode The IP submask gateway are null when you select the DHCP mode to auto search the IP If you select the static mode you need to set the IP submask gateway manually If you select the DHCP mode you can view the IP submask gateway from the DHCP If you switch from the DHCP mode to the static mode you need to reset the IP parameters Besides IP submask gateway and DHCP are read only when the PPPoE dial is OK Mac Address It is to display hose Mac address 20 IP Version It is to select IP version IPV4 or IPV6 You can access the IP address of these two version IP Address Please use the keyboard to input the corresponding number to modify the IP address and then set the corresponding subnet mask and the default gateway Preferred DNS DNS IP address Alternate DNS Alternate DNS IP address Enable You can use ARP Ping command to modify or set
12. box to enable WIFI function and then click the Search SSID button Now you can view all the wireless network information in the following list Double click a name to connect to it See Figure 4 18 32 IWatcO NE Camera Network gt TCP IP gt Connection Connect To huaguest gt PPPoE huaquest gt DDNS huso Signal aa E TP LINK anra S a gt SMTP E mail Authentication Manner WPA PSK TKIP gt UPnP Input Password gt SNMP A gt Bonjour gt Multicast WIFI INFO cane Current x gt aos Hot Spot any connecting Event IP address Storage Subnetmask System Default IP Gateway Information Figure 4 18 4 2 12 Qos The QoS interface is shown as below See Figure 4 19 Qos Quality of Service is network security mechanism It is a technology to fix the network delay and jam problem and etc For the network service the quality of service includes the transmission bandwidth delay the packet loss and etc We can guarantee the transmission bandwidth lower the delay reduce the loss of the data packet and anti dither to enhance the quality We can set the DSCP Differentiated Services Code Point of the IP to distinguish the data packet so that the router or the hub can provide different services for various data packets It can select the different queues according to the priority of the packets and select the bandwidth of the each queue lt can also discard at the different ratio when the broad bandwidth is jam
13. iris preset tour pan scan pattern aux close and PTZ setup button See Figure 3 1 e PTZ direction PTZ supports eight directions left right up down upper left upper right bottom left bottom right Oo Speed The step 8 speed is faster than step 1 You can click this icon to display or hide the PTZ control platform Figure 3 1 PTZ Interface Click PTZ set button the interface is shown as in Figure 3 2 Set Left Lirit Set Aight Limit Preset Effective Scope 0 255 o Add Delete Tour Effective Scope 1 255 i Add Delete Delete Group Pattern Effective Scope 1 255 i Start Record Stop Record Assistant Compensation ka Start Stop Matris Monitor Output f Video Input o Matris ID f Video Switch Light Wiper Turn on Turn off Figure 3 2 PTZ Setup Please refer to the following sheet for PTZ setup information Scan Move the camera to you desired location and then click left limit button e Then move the camera again and then click right limit button to set a right limit Preset Use direction keys to move the camera to your desired location and then input preset value Click add button you have set one preset The preset value ranges from 1 to 80 It may vary due to different protocols Tour Input auto tour value and preset value Click add button you have added one preset in the tour Repeat the above procedures you can add more presets in one tour Or you can cli
14. sheet for detailed information Parameter Function Brightness It is to adjust monitor window bright The value ranges from O to 100 The default value is 50 The larger the number the bright the video is When you input the value here the bright section and the dark section of the video will be adjusted accordingly You can use this function when the whole video is too dark or too bright Please note the video may become hazy if the value is too high The recommended value ranges from 40 to 60 11 Gain Adjust Exposure Mode It is to adjust monitor window contrast The value ranges from 0 to 100 The default value is 50 The larger the number the higher the contrast is You can use this function when the whole video bright is OK but the contrast is not proper Please note the video may become hazy if the value is too low If this value is too high the dark section may lack brightness while the bright section may over exposure The recommended value ranges from 40 to 60 It is to adjust monitor window hue The value ranges from 0 to 100 The default value is 50 The input value will adjust the hue but has no effect on the general brightness of the whole video Such as turn the red color to the blue color There is a default value according to the sensitization of the sensor Usually you do not need to do some major setup The recommended value ranges from 40 to 60 It is to adjust monitor window saturation The value ra
15. sound file 59 6 Log out Click log out button system goes back to log in interface See Figure 6 1 Figure 6 1 Note e Slight difference may be found in user interface eo All the designs and software here are subject to change without prior written notice 60
16. the device IP ARP Ping set address if you know the device MAC address device IP Before the operation please make sure the MPIX and the PC address service in the same LAN This function is on by default You can refer to the steps listed below Step 1 Get an IP address Set the MPIX and the PC in the same LAN Step 2 Get the physical address from the label of the MPIX Step 3 Go to the Run interface and then input the following commands arp s lt IP Address gt lt MAC gt ping 480 t lt IP Address gt Such as arp s 192 168 0 125 11 40 8c 18 10 11 ping 480 t 192 168 0 125 Step 4 Reboot the device Step 5 You can see the setup is OK if you can see there are output information such as Reply from 192 168 0 125 from the command output lines Now you can close the command line Step 6 Open the browse and then input http lt IP addres gt Click the Enter button you can access now 4 2 2 Connection The connection interface is shown as in Figure 4 8 21 WatchN Ei Camera Connection Network Max Connection 1 20 gt TCPIIP 5 TCP Port 1025 65535 gt PPPoE MOR Er 1025 65535 NA HTTP Port 80 RTSP Port 554 gt IP Filter gt SMTP E mail gt UPnP gt SNMP gt Bonjour gt Multicast gt WIFI gt aos Event Storage System Information Figure 4 8 Please refer to the following sheet for detailed information Parameter Function Max It i
17. MPIX Web Manual Table of Contents 1 Network Connection iii tidad 1 2 Mal intenace Introducido 2 2 1 e e y II cae E va dieedaun Sus ON 2 2 2 EVENE AAA II O A E ane ioakt 4 2 9 ENCONS Se UDa E E A EA te 4 2 4 IVS EN MG PP E A N E A Pe 5 25 Video Window FUNCTION OPTION ccccccnnnnnnncnnnaonacnnnnonononoconononanananananonnnnnnnononcncnonons 5 2 6 video VVINGOW SUD 6 o E call A Y cf 6 EEA Omer meen o e T 8 A NT 11 4 1 EAE E caida nse etic he ects ea dee E A eke redhead dessin ach A E 11 a a O A A A ANAE 11 A AG AS 14 AROS O A II AN AOS 18 4 2 NOWO A A Cane MS OUTER CSTE SOeee ORE 19 A 2w OPRI acct esl ears ace ested dor se uk sacar A 19 4 22 NA A eee e OE EN OF eet Se On ON OF Ne rn ne eee ee 21 AL dl ad gg ae Ee eee NI 23 AZA DDNS ee ee ee eC 23 AE a i E E SE EE EEE ENEE E AE TAS 24 426 SMTP e mail ooccnnnnnncccnnnnnnnnnccnnnnnonnnonnnnnnonnnnnnnnnnonnnnnnnnnnnnnnnnncnnnnnninnnnnnnnnas 25 AT GROP ea aT ene Sree ma arte eMC eR ROT Tomer ne en Om RET Eg Monty reson 27 ARS NME oaea E E il cd at led ocd do 28 Teo BONO e No E E O oe enn mee ae ee eee ree 30 4 2 10 UB AI N IN ha researches S 30 4 2 11 AAA Lo A E EEE E A EEA EEE O E EA EE E A 31 4 2 12 setas 33 4 3 AA A 34 ASI o 31 Sener eee enna et A A eT Sennen tie Recto 34 PEE A II ein cigs emcees ne saat oases ek 40 430 0 ADNO sido caia 42 4 4 b ane Pr ae er re ee 44 4 4 1 Record schedule and snapshot schedu
18. Z gt Default gt ImportExport gt Auto Maintain gt Upgrade Information Figure 4 38 Please refer to the following sheet for detailed information Device No It is to set device name Video This is to display video standard such as PAL Standard Language You can select the language from the dropdown list Please note the device needs to reboot to get the modification activated 4 5 1 2 Date and time The date and time interface is shown as in Figure 4 39 48 WatchN Eji Camera Network Event Storage System gt gt Account ne Pre gt Default gt ImportExport gt Auto Maintain gt Upgrade Information General Date amp Time Date Format Year Month Day Time Format GMT 08 00 10 Time Zone Current Time 2011 Port 37 Update Period 10 24 Hour based System DST Enable DST Type ODate Week Start Time Jan w ist Sunday aal 00 00 End Time Jan w 2nd Monday 00 00 Synchronize with NTP NTP Server clock isc org Minute 0 30 9 i 4 a cr O ee r x y 25 11 03 50 Sync PC Figure 4 39 Please refer to the following sheet for detailed information Date format Here you can select date format from the dropdown list Time Format There are two options 24 H and 12 H The time zone of the device Sync PC System It is to set system time You can click this time can set according f
19. address here Blank Page Windows Internet Explorer sis 7 about blank amp ww Blank Page Figure 2 1 IE The login interface is shown as below See Figure 2 2 Please input your user name and password Default factory name is admin and password is 1234 Figure 2 2 Login Interface If itis your first time to login in system pops up warning information to ask you whether install control webrec cab or not Please click OK button system can automatically install the control When system is upgrading it can overwrite the previous Web too If you can t download the ActiveX file please check whether you have installed the plug in to disable the control download Or you can lower the IE security level See Figure 2 3 Internet Options 2 Security Settings Internet Zone General Security Privacy Content Connections Programs Advanced Settings Disable Select a zone to view or change security settings Enable 4 Download signed Activex controls not secure Disable 2 Enable not secure X Jv 4 Internet Local intranet Trusted sites ao O Prompt recommended Internet mz 9 Download unsigned Actives controls mot secure tod This zone is for Internet websites ae Disable recommended except those listed in trusted and 0 Enable not secure restricted zones O p t romp l Initialize and script Actives controls not marked as safe For s Security
20. ck delete button to remove one preset from the tour The tour value ranges from 1 to 255 It may vary due to different protocols Parameter Function Pattern You can input pattern value and then click start record button to begin PTZ movement Please go back to Figure 3 1 to implement camera operation Then you can click stop record button in Figure 3 2 Now you have set one pattern Assistant The assistant items include BLC Digital zoom night vision camera brightness flip You can select one option and then click start or stop button Matrix Please select the matrix X and then input the corresponding monitor output number video input channel number and then you can click video switch button to complete the operation Light and You can enable or disable the light wiper wiper 10 4 Setup 4 1 Camera 4 1 1 Conditions Here you can view device property information Slight differences may be found due to different MPIX series The setups become valid immediately after you set See Figure 4 1 Camera Conditions gt Video Brightness o A 50 Network Contrast D 50 Event Hues f 50 Storage Saturation 4 50 Gain Mode Auto O Manual System Information Gain Upper Limit j s0 Exposure Mode Auto Manual Scene Mode Auto lv Day Night Mode Auto Backlight OFF Mirror O ON OFF Flip ON O OFF Figure 4 1 Please refer to the following
21. count gt PTZ gt gt ImportExport gt Auto Maintain gt Upgrade Information Figure 4 47 4 5 5 Import Export The interface is shown as in Figure 4 48 55 WatchiNEi Camera Import Export Network Event Backup Path System gt General gt Account va Ta gt Default gt gt Auto Maintain gt Upgrade Information Figure 4 48 Please refer to the following sheet for detailed information Import It is to import the local setup files to the system Export It is to export the corresponding system setup to your local PC 4 5 6 Auto maintenance The auto maintenance interface is shown as in Figure 4 49 Here you can select auto reboot and auto delete old files interval from the dropdown list If you want to use the auto delete old files function you need to set the file period Camera Auto Maintain Network Event Auto Reboot Everyday 02 00 Storage Auto Delete Old Files Customized lv 1 Days ago System gt General Manual Reboot gt PTZ gt Default gt ImporiExport gt gt Upgrade Information Figure 4 49 56 4 5 7 Firmware update The firmware interface is shown as in Figure 4 50 Please select the upgrade file and then click the update button to begin firmware update Important Improper upgrade program may result in device malfunction WatchN Eji Camera Upgrade Network Event Select Firmware File Storage System gt Gene
22. d in the SD card 45 Parameter Function It saved in the FTP server lt can save according to the corresponding network protocol The local interface is shown as in Figure 4 34 Here you can view local SD card or disk information You can also operate the read only write only hot swap and format operation Watch NE Camera Network Network Event Device Name Attribute Free Capacity Total Capacity Storage gt Schedule gt gt Conditions System Information Read Only Read amp Write Hot Swap Figure 4 34 The FTP interface is shown as in Figure 4 35 You need to check the box to enable the FTP function When network disconnect occurred or there is malfunction Emergency storage can save the record snapshot picture to the local SD card Camera Network Network Event Enable Storage Server IP gt Schedule Port 21 0 65535 User Name anonymity gt Conditions Password System Remote Path share Information Emergency Local Figure 4 35 46 The network interface is shown as in Figure 4 36 You need to check the box to enable the network Please select the mode from the dropdown list It includes NFS ISCSI and etc You can select according to your actual requirements mus PA A E IA TA Camera Network Network Event Enable Storage Protocol NFS gt Schedule Server IP gt Part 21 0 65535 gt Conditions User Name System Password
23. e 4 27 through Figure 4 31 IP Conflict SD Card Error Disconnection Camera No SD Card Network Capacity Warning Enable Event gt Video Detect Relay out gt Alarm Relay out Delay 10 Second 10 300 gt O Send E Mail Storage Information Figure 4 27 IP Conflict Disconnection SD Card Error Camera No SD Card Network Capacity Warning O Enable Capacity Limit 10 0 99 Event gt Video Detect gt Alarm Relay out gt Relay out Delay 10 Second 10 300 storage Send E Mail System Information Figure 4 28 42 Camera No SD Card Capacity Warning SD Card Error Disconnection IP Conflict Network Event O Enable gt Video Detect Relay out gt Alarm Relay outDelay 10 Second 10 300 C Send E Mail Storage Information Figure 4 29 Camera No SD Card Network SD Card Error Disconnection IP Conflict Capacity Warning Enable Event gt Video Detect Record gt Alarm Record Delay 10 Second 10 300 gt Relay out Storage Relay outDelay 10 Second 10 300 System Information Default Figure 4 30 E WatchNEN Camera No SD Card Capacity Warning SD Card Error Disconnection IP Conflict Network O Enable Event gt Video Detect Record gt Alarm Record Delay 10 Second 10 300 m Relay out UL Storage Relay outDelay 10 Second 10 300 System Information Default
24. e as 18 00 00 The video in the specified period will be color while the video in the rest period will be black and white This function can make the target clearer It can make the details of the dark section become clear when the background is too bright This function is disabled by default 13 Flip It is to switch video up and bottom limit This function is disabled by default Mirror It is to switch video left and right limit This function is disabled by default Some series product does not support this function 4 1 2 Video 4 1 2 1 Video bit stream The video bit stream interface is shown as below See Figure 4 2 HED EISM OE Lote A setup A P Logout Camera Video Snapshot Overlay Path gt Conditions Main Stream Sub Stream gt gt Audio C Enable Code Stream Type General EA Network Code Stream Type General lv Encode Mode H 264 hd Event Encode Mode H 264 y St Resolution 1080P 1920 1080 w hot be Resolution CIF 352 288 y peere Frame rate FPS 25 A y ae Te Frame rate FPS 6 y x it Rate Type v tad E Bit Rate Type CBR Mm Reference Bit Rate 3584 8192Kb S Reference Bit Rate 48 256Kb S Bit Rate 8192 E _ Bit Rate 80 Frame Interval 50 25 150 gt Frame Interval 12 6 150 Watermark Settings Watermark Character DigitalCCTV Figure 4 2 Please refer to the following sheet for detailed information Parameter Function Main Bit
25. email test please save the email setup information 4 2 7 UPnP It allows you to establish the mapping relationship between the LAN and the public network Here you can also add modify or remove UPnP item See Figure 4 13 In the Windows OS From Start gt Control Panel gt Add or remove programs Click the Add Remove Windows Components and then select the Network Services from the Windows Components Wizard Click the Details button and then check the Internet Gateway Device Discovery and Control client and UPnP User Interface Please click OK to begin installation Enable UPnP from the Web If your UPnP is enabled in the Windows OS the MPIX can auto detect it via the My Network Places Update period interval 21 WatchiNEis Camera UPnP Network C Enable Status Mapping Failed gt TCP IP E E Ae Port Mapping List gt Connection Service Name Protocol Internal Port External Port gt PPPoE gt DDNS gt IP Filter Hew E gt SMTP E mail gt gt SNMP gt Bonjour gt Multicas gt WIFI gt aos Event Storage System Information Figure 4 13 4 2 8 SNMP The SNMP interface is shown as in Figure 4 14 The SNMP allows the communication between the network management work station software and the proxy of the managed device Please install the software such as MG MibBrowser 8 0c software or establish the SNMP service before you use this function You need to
26. erver regularly e You can set interval value between the device and DDNS filter server here 24 The IP filter interface is shown as in Figure 4 11 You can enable IP filter function so that some specified IP user can access the MPIX You can add IP address or IP address section If you do not check the box here it means there is on access limit WatchN E Camera IP Filter Network Trusted Sites gt TCP IP Trusted Sites gt Connection IP address gt PPPoE gt DDNS gt gt SMTP E mail gt UPnP gt SNMP gt Bonjour gt Multicast Add IP gt WIFI gt aos Event Storage System Information Figure 4 11 4 2 6 SMTP e mail The SMTP interface is shown as in Figure 4 12 Remove All gt an D Watch NEN Camera Network gt TCP IP gt Connection gt PPPoE gt DDNS gt IP Filter gt gt UPnP gt SNMP gt Bonjour gt Multicast gt WIFI gt aos Event Storage System Information SMTP E mail SMTP Server Port Anonymity Username anonymity Password ecce Sender none Authentication None Title IPC Message Attachment Mail Receiver Interval 0 Second 0 3600 Health Mail Update Period Minute 1 3600 Email Test Figure 4 12 Please refer to the following sheet for detailed information SMTP Server Input server address and then enable this function Default value is 25 You can modify it if necessary Anonymity For t
27. f your device supports Sub Extra lf network width is not sufficient you can use sub stream to stream realize network monitor Protocol You can select stream media protocol from the dropdown list There are three options TCP UDP Multicast 2 4 System Menu System menu is shown as in Figure 2 6 Please refer to chapter 2 2 Live chapter 3 PTZ chapter 4 Setup chapter 5 Alarm chapter 6 Log out for detailed information 2 5 Video Window Function Option The interface is shown as below See Figure 2 7 Figure 2 7 Video Window Function Please refer to the following sheet for detailed information 4 Alarm Click it to generate an alarm output output 2 Digital Click this button and then left drag the mouse in the zone to 200m zoom in Right click mouse system restores original status 3 Snapshot You can snapshoot important video All images are memorized in system folder 1 picture download default You can go to Setup gt Camera gt Video gt Path to modify the local record save path 4 Record When you click local record button the system begins recording The recorded file is saved to system folder Record Download default You can go to Setup gt Camera gt Video gt Path to modify the local record save path 5 Audio Turn on or off audio when you are monitoring output Some series product does not support this function Bidirectional Click it to begin audio talk You can go to Setup gt Camera talk gt
28. h Clear Log Upgrade Auto Maintain General Video Audio Schedule Destination Network Abnormality Video Detect Default import Export Conditions Figure 4 40 Add user lt is to add a name to group and set the user rights See Figure 4 41 There are four default users admin user guest and hidden user default Except user guest other users have administrator right The user guest can only have the monitor rights 50 Hidden user default is for system interior use only and can not be deleted When there is no login user hidden user default automatically login You can set some rights such as monitor for this user so that you can view some channel view without login Here you can input the user name and password and then select one group for current user Please note the user rights shall not exceed the group right setup For convenient setup please make sure the general user has the lower rights setup than the admin WatchNEN Camera Network Event Storage System gt General gt gt PTZ gt Default gt ImportiExport Account User Name Add User User Name Password Confirm Password Group Remark Group Name gt Auto Maintain Authority List All oo Shutdown Reboot Information Live Authority List Record control shutdown R HDD S Relay in out Log Search Clear Log PTZ Network Alarm Add User Figure 4 41 Modify user It is to modify the user property belo
29. he max bit stream value in the recommend bit to get the better video output effect Resolution There are multiple resolutions You can select from the dropdown list For each resolution the recommended bit stream value is different m Rate PAL 1 25f s NTSC 1 30f s parere fom frame rate may vary due to different resolutions There are two options VBR and CBR Bit Rate Type e Bit Rate Type Please note you can set video quality in VBR mode D Recommended bit rate value according to the resolution D and frame rate you have set Bit Rate e In CBR the bit rate here is the max value In dynamic video system needs to low frame rate or video quality to guarantee the value e The value is null in VBR mode e Please refer to recommend bit rate for the detailed information Frame Here you can set the P frame amount between two frames The value ranges from 1 to 150 Default value is 50 Recommended value is frame rate 2 4 1 2 2 Snapshot The snapshot interface is shown as in Figure 4 3 WatchNEis Camera Snapshot Overlay gt Conditions Snapshot Type General Image Size gt Audio g Network BUD Event Interval 15 td System Information Figure 4 3 Please refer to the following sheet for detailed information There are two modes general schedule and Event activation It is the same with the resolution of the main stream Quality It is to set the image quality There are six levels It i
30. he server supports the anonymity function You can auto login anonymously You do not need to input the user name password and the sender information The user name of the sender email account The password of sender email account Sender email address Authentication You can select SSL or none Encryption mode Title Subject Input email subject here Attachment System can send out the email of the snapshot picture once you check the box here Mail receiver Input receiver email address here Max three addresses 26 Parameter Function The send interval ranges from 0 to 3600 seconds 0 means there is no interval Please note system will not send out the email immediately when the alarm occurs When the alarm motion detection or the abnormity event activates the email system sends out the email according to the interval you specified here This function is very useful when there are too many emails activated by the abnormity events which may result in heavy load for the email server Interval Health mail Please check the box here to enable this function enable This function allows the system to send out the test email to check the connection is OK or not Please check the box to enable this function and then set the corresponding interval System can send out the email regularly as you set here Email test The system will automatically sent out a email once to test the connection is OK or not Before the
31. iNEis Camera PTZ Network Protocol PELCOD Event Address 1 Storage Baudrate 9600 System gt General Data Bit g gt Account Stop Bit 1 Parity None Sone Defaut Default gt ImportExport gt Auto Maintain gt Upgrade Information admin administrator group All Shutdown Reboot Live M Record control HDD PTZ Save Cancel Record control Backup HDD RIZ Account Relay infout System Update Auto Maintain General Setting Encode Record RS232 Video Detect Rie Default Video Input Figure 4 45 E is 5 5 8 Figure 4 46 Please refer to the following sheet for detailed information SA A CO A OA Select the corresponding dome protocol Protocol Address Set corresponding dome address Default value is 1 Please note your setup here shall comply with your dome address otherwise you can not control the speed dome Select the dome baud rate Default setup is 9600 Rate Data Bit Default setup is 8 Please set according to the speed dome dial switch setup Stop bit Default setup is 1 Please set according to the speed dome dial switch setup Parity Default setup is none Please set according to the speed dome dial switch setup 4 5 4 Default The default setup interface is shown as in Figure 4 47 Please note system can not restore some information such as network IP address Watch yE arm Camera Default Network Storage System gt General gt Ac
32. ice information You can access the client end via this address Watch NEN Camera PPPoE Network gt TCP IP O Enable gt Connection Username gt Password gt DDNS gt IP Filter gt SMTP E mail gt UPnP gt SNMP gt Bonjour gt Multicast gt WIFI gt QoS Event Storage System Information Figure 4 9 4 2 4 DDNS The DDNS interface is shown as in Figure 4 10 23 The DDNS is to set to connect the various servers so that you can access the system via the server Please go to the corresponding service website to apply a domain name and then access the system via the domain lt works even your IP address has changes WatchiNEi Camera Network gt TCP IP gt Connection gt PPPoE gt gt IP Filter gt SMTP E mail gt UPnP gt SNMP gt Bonjour gt Multicast gt WIFI gt QoS Event Storage System Information Server Type Server IP Port Domain Name Username Password Update Period CN99 DDNS none 60 1 65535 5 Minute 1 500 Figure 4 10 Please refer to the following sheet for detailed information 4 2 5 IP Parameter Server Type You can select DDNS protocol from the dropdown list and then enable DDNS function The private DDNS protocol means you use your self defined private protocol to realize DDNS function Server IP Server Port Domain Name User Password Update period e Device sends out a live signal to the s
33. le ooccooooccccnoooccnccononnncconnannnonnno 44 4A 2 MESA MM e tes ri RTN 45 Ao RECO CONO utonntonen leido eo lesiona lois Man ear cales lat 47 4 5 SVS Le eerste att hoes cine Ste eae averages tensa eo ea aeons 48 4 5 1 Generals it rd et diana 48 AD A IS 50 7a Ta Si AAA Oe 54 ADA MEA atleta 55 AO IN PONEN di ote 55 A56 AUTO Manten Ne e deal ns NEO 56 4S A Gam dc A ree ie Mtr roe ae eee ete Pr one 57 4 6 NR 57 AG MUA a tose o O 57 Aa EO O 58 By PANGAN TAM A E 59 0 MOTO ica 60 Important The following functions are for reference only Some series products may differ from the functions listed below 11 1 Network Connection This series MPIX product support the Web access and management via PC Web includes several modules includes monitor channel preview PTZ control system configuration alarm and etc Please follow the steps listed below for network connection Make sure the MPIX has connected to the network properly e MPIX IP address and PC IP address shall be in the same network segment If there is router please set the corresponding gateway and subnet mask e Use order ping IP camera address to check connection is OK or not 2 Main Interface Introduction 2 1 Log in Open IE and input IP camera address in the address bar For example if your camera IP is 192 168 1 108 then please input http 192 168 1 108 in IE address bar See Figure 2 1 Input your IP
34. led the corresponding record mode in the Setup gt Storage gt Conditions You can view the current time period setup from the color bar e Green color stands for the general record snapshot e Yellow color stands for the motion detect record snapshot e Red color stands for the alarm record snapshot 44 WatchN Eji Camera Network Event Storage gt gt Destination gt Conditions Record Schedule 0 2 4 6 uy Monday Tuesday Wednesday snapshot Schedule a Setup System Thursday Information Friday Saturday Figure 4 32 4 4 2 Destination The destination interface is shown as in Figure 4 33 It is to set the storage mode of the MPIX record file or snapshot pictures There are three options local FTP network You can only select one mode System can save according to the event types It is corresponding to the three modes general motion alarm in the Schedule interface Please check the box to enable the save functions Watch NEN Camera Path Network PMA RAP TA Network Record Snapshot Event Storage Event Type Timer Motion Detect Alarm Event Type Timer Motion Detect Alarm gt Schedule Local oo FTP O O O FTP DO O o gt Conditions Network go O O O O 5 O System Information Figure 4 33 Please refer to the following sheet for detailed information Parameter Function Event Type lt includes general motion detect and alarm Local It save
35. level for this zone O Disable ded A Disable recommende Allowed levels For this zone Medium to High Enable not secure A e Medium high Prompt E e Appropriate For most websites Prompts before downloading potentially unsafe a Run Acke controls and plug ins content An Adraimickr shar anne Unsigned Activer controls will not be downloaded Iy Takes effect after you restart Internet Explorer Ea Reset custom settings Reset to medium high default v Reset all zones to default level oh Figure 2 3 Security Settings 2 2 Live Interface After you logged in you can see the live monitor window See Figure 2 4 A http 1110 15 5 84 8088 Windows Internet Explorer File Edit View Favorites Tools Help r i A j i gt Y ja v Back gt E a i A Search HZ Favorites E LS E Ly Address http 10 15 5 84 8088 Watch NEIT A o 5a l Local intranet Figure 2 4 Live Interface There are four sections e Section 1 Encode setup bar e Section 2 System menu e Section 3 Window function option bar e Section 4 Window adjust bar 2 3 Encode Setup The encode setup interface is shown as in Figure 2 5 Figure 2 5 Encode setup Please refer to the following sheet for detailed information Parameter Function Main stream In normal network width environment main stream can record audio video file and realize network monitor You can set the main stream resolution i
36. nges from O to 100 The default value is 50 The larger the number the strong the color is This value has no effect on the general brightness of the whole video The video color may become too strong if the value is too high For the grey part of the video the distortion may occur if the white balance is not accurate Please note the video may not be attractive if the value is too low The recommended value ranges from 40 to 60 There are two options manual auto The gain adjust is to set the gain value The default value may vary due to different device models The smaller the value the low the noise But the brightness is also too low in the dark environments It can enhance the video brightness if the value is high But the video noise may become too clear There are two modes Auto exposure AE and Manual exposure ME There are several values for the manual exposure mode You can select from the dropdown list It support the long exposure lt supports customized setup too The device can auto exposure according to the exposure time you set here The value ranges from 0 1 to 80ms The exposure time is fixed if the max and min value are the same Customized value System can auto exposure according to the value you set here The value ranges from 0 1 to 80ms 12 Auto Iris Scene Mode Day Night Mode Before the setup please make sure you have installed the auto Iris You can check the box before ON to enable
37. nging group password and rights See Figure 4 42 Modify password It is to modify the user password You need to input the old password and then input the new password twice to confirm the new setup Please click the OK button to save Please note the password ranges from 1 digit to 6 digit It shall include the number only For the user of the account rights he can modify the password of other users 51 Watch NEI Camera Account Network User Name Event Storage Modify iser System User Name admin General Modify Password Group admin Remark admin s account Default Import Export o Authority List TA Auto Maintain 7 Shutdown Reboot 7 Live Information 7 Record control 7 Storage Authority List M Account Clear Log Network Video Detect Default import Export Conditions gt Upgrade Figure 4 42 4 5 2 2 Group The group management interface can add remove group modify group password and etc The interface is shown as in Figure 4 43 32 Watch NEN Camera Network Account User Name Group Event i Group Name Storage System user group gt General gt PTZ Default Import Export Auto Maintain Upgrade Information Authority List Shutdown Reboot Live Log Search Clear Log Network Alarm Add Group Record control Backup HDD BTE Account Relay infout System Update Auto Maintain General Setting Encode Record RS232 Video Detect PRIZ Default Video Input
38. og Logout Login Login Logout Add Group Add User Logout Login M4 111 gt bi GoTo Clear Search You can select log type from the drop down list and then click search button to view the list You can click the stop button to terminate current search operation Detailed You can select one item to view the detailed information information Clear You can click this button to delete all displayed log files Please note system does not support clear by type You can click this button to backup log files to current PC 58 5 Alarm Click alarm function you can see an interface is shown as in Figure 5 1 Here you can set device alarm type and alarm sound setup Alarm Type Motion Detect Disk Error External Alarm Operation O Prompt Alarm Tone O Play Alarm Tone Tone Path live prz setup CO SA Alarm Type O Disk Full O Video Masking hemes Figure 5 1 Alarm Please refer to the following sheet for detailed information Alarm Motion detection System alarms when motion detection alarm type occurs Disk full System alarms when disk is full malfunction malfunction masking External alarm Alarm input device sends out alarm Some series product does not support this function System automatically pops up alarm dialogue box Alarm Audio When alarm occurs system auto generates alarm audio audio The audio supports customized setup lo Path Here you can specify alarm
39. orizes one event during the anti dither period The value ranges from Os to 100s Relay out Enable alarm activation function You need to select alarm output port so that system can activate corresponding alarm device when alarm occurs Some series product does not support this function Alarm Delay System can delay the alarm output for specified time after alarm ended The value ranges from 10s to 300s Some series product does not support this function Record System auto activates motion detection channel to record once channel alarm occurs working with motion detection function Please note you need to go to Storage gt Schedule to set current channel as general record Record Delay System can delay the record for specified time after alarm ended The value ranges from 10s to 300s Email If you enabled this function System can send out email to alert you when alarm occurs PTZ e Here you can set PTZ movement when alarm occurs Such as go to preset x when there is an alarm e The event type includes preset tour and pattern Some series product does not support this function Capture You need to input capture channel number so that system can backup motion detection snapshot file 39 4 3 2 Alarm Please note some series product does not support this function 4 3 2 1 Alarm activation The alarm activation interface is shown as in Figure 4 25 WatcoNer E Relay out Camera
40. ormat N You can set the time server address It is to set the time server port Update period time lt becomes valid after you set button to save the system time as your PC current Here you can set day night save time begin time and end time You to the date format or according to the week You can check the box to enable NTP function It is to set the sync periods between the device and the time server 49 4 5 2 Account Note e For the character in the following user name or the user group name system max supports 6 digits The space in the front or at the end of the string is null The valid string includes character number and underline e The user amount is 20 and the group amount is 8 when the device is shipped out of the factory The factory default setup includes two levels user and admin You can set the corresponding group and then set the rights for the respective user in the specified groups e User management adopts group user modes The user name and the group name shall be unique One user shall be included in only one group 4 5 2 1 User name In this interface you can add remove user and modify user name See Figure 4 40 Watch NEJA Camera Account Network Event Storage System admin s account gt General user s account gt Default gt Import Export gt Auto Maintain gt Upgrade Information Authority List Shutdown Reboot Live Record control Storage Account Log Searc
41. ral gt Account PTZ gt Default gt ImporiExport gt Auto Maintain gt Information Figure 4 50 4 6 Information 4 6 1 Version The version interface is shown as in Figure 4 51 Here you can view system hardware features software version release date and etc Please note the following information is for reference only Camera Version Network sofware Version 2 103 WT00 0 T build 2013 05 20 Event WEB Version 3 0 0 0 Storage SIN 14MPIX20W4DWIRM1212 00500334 System CopyRight 2011 All Rights Reserved Information 2 Online User T al a i 57 Figure 4 51 4 6 2 Log Here you can view system log See Figure 4 52 WatchiNEi Camera Network Event Storage System Information gt Version gt Start Time 2011 10 24 13 26 57 End Time 2011 10 25 13 26 57 mi Find 25 log Log Time 2011 10 24 14 12 45 2011 10 25 13 28 09 2011 10 25 13 28 09 2011 10 25 13 28 07 2011 10 25 13 17 35 2011 10 25 12 35 07 2011 10 25 11 52 34 2011 10 25 11 45 16 2011 10 25 10 17 29 2011 10 25 10 17 26 Type All 1 2 3 4 5 6 7 8 Detailed Information Figure 4 52 Please refer to the following sheet for log parameter information Type Log types include system operation configuration operation data operation event operation record operation user management log clear Start time Set the start time of the requested log Set the end time of the requested l
42. reboot the device to activate the new setup 28 Watch NEN Camera SNMP Network gt TCP IP SNMP v1 gt Connection SNMP v2 gt PPPoE SNMP Port 161 1 65535 gt DDNS Read Community public gt IP Filter Write Community private gt SMTP E mail Trap Address gt UPnP Trap Port 162 1 65535 gt gt Multicast gt WIFI gt aos Event Storage System Information Figure 4 14 Please refer to the following sheet for detailed information SNMP V1 System only processes the information of V1 SNMP V2 System only processes the information of V2 SNMP Port The listening port of the proxy program of the device lt is a UDP port not a TCP port The value ranges from 1 to 65535 The default value is 161 Read Community lt is a string lt is a command between the manage process and the proxy process It defined the authentication access control and the management relationship between one proxy and one group of the managers Please make sure the device and the proxy are the same The read community will read all the objects the SNMP supported in the specified name The default setup is public Write Community It is a string lt is a command between the manage process and the proxy process It defined the authentication access control and the management relationship between one proxy and one group of the managers Please make sure the device and the proxy are the same The read community will read write acce
43. s the max Web connection for the same device The value ranges from 1 connection to 20 The max connection amount is 20 TCP port The default value is 4000 You can input the actual port number if necessary UDP port The default value is 4001 You can input the actual port number if necessary HTTP port The default value is 80 You can input the actual port number if necessary 22 RTSP port The default value is 554 Rtsp streay query format is Main stream risp username password Wip port cam realmonitor channel 1g8subtype 0 Sub stream rtsp Username password ip port cam realmonitor channel 1 amp subtype 1 You need to input the following four items manually Username password IP and port The IP is device IP and the port default value is 554 You can leave it in blank if it is the default value You do not need to input the user name and password if you do not need to the verification Such as rtsp ip port cam realmonitor channel 1 amp subtype 0 4 2 3 PPPoE The PPPoE interface is shown as in Figure 4 9 Input the PPPoE user name and password you get from the IPS internet service provider and enable PPPoE function Please save current setup and then reboot the device to get the setup activated Device connects to the internet via PPPoE after reboot You can get the IP address in the WAN from the IP address column Please note you need to go to the IP address item to via the device current dev
44. s to set snapshot frequency The value ranges from 1s to 7s 4 1 2 3 Video Overlay The video overlay interface is shown as in Figure 4 4 Watch NEI Camera snapshot Overlay gt Conditions z i Yi EF a ell q ue FF i a ee a O Privacy Masking Tli a gt Audio Network Channel Title Event System Time Title pi gt Hi f i i i F 7 a o Storage x PE AA 7i information 17 Figure 4 4 Please refer to the following sheet for detailed information Parameter Function Privacy mask e Here you can privacy mask the specified video in the monitor video e System max supports 4 privacy mask zones Time Title e You can enable this function so that system overlays time information in video window e You can use the mouse to drag the time tile position Channel Title e You can enable this function so that system overlays channel information in video window e You can use the mouse to drag the channel tile position 4 1 2 4 Path The storage path interface is shown as in Figure 4 5 Here you can set snap image saved path e in the preview interface and the record storage path in the preview interface The default setup is C PictureDownload Please click the Save button to save current setup Camera Snapshot Overlay gt Conditions gt Snapshot Path C PictureDownload gt Audio Record Path C RecordDownload Network Storage System Information Figure 4 5
45. ss all the objects the SNMP supported in the specified name The default setup is write Trap address The destination address of the Trap information from the proxy program of the device 29 Parameter Function The destination port of the Trap information from the proxy program of the device lt is for the gateway device and the Trap port client end PC in the LAN to exchange the information lt is a non protocol connection port It has no effect on the network applications It is a UDP port not TCP port The value ranges from 1 to 165535 The default value is 162 4 2 9 Bonjour The Bonjour interface is shown as below See Figure 4 15 Bonjour is based on the multicast DNS service from the Apple The Bonjour device can automatically broadcast its service information and listen to the service information from other device You can use the browse of the Bonjour service in the same LAN to search the MPIX device and then access if you do not know the MPIX information such as IP address You can view the server name when the MPIX is detected by the Bonjour Please note the safari browse support this function Click the Display All Bookmarks and open the Bonjour system can auto detect the MPIX of the Bonjour function in the LAN Watch NEJIN Camera Bonjour Network gt TCP IP Enable gt Connection Server Name PC HF3300 TZC1CWW15200022 gui gt DDNS gt IP Filter gt SMTP E mail gt UPnP gt SNMP gt
46. stream type It includes general stream motion stream and alarm stream stream You can select different encode frame rates form different recorded events System supports active control frame function ACF allows you to record in different frame rates For example you can use high frame rate to record important events record scheduled event in lower frame rate and it allows you to set different frame rates for motion detection record and alarm record 14 Parameter Function Encode mode There are three options H 264 main profile standard H 264B baseline standard encode and MJPG encode eo The H 264 and H 264B both are H264 bit stream H 264 is the Main Profile encode and the H 264B is the Baseline Profile encode mode H 264B is for Blackberry cell phone to realize the monitor MJPEG In this encode mode the video needs to large bit stream to guarantee the video definition You can use the max bit stream value in the recommend bit to get the better video output effect Resolution There are multiple resolutions You can select from the dropdown list For each resolution the recommended bit stream value is different Frame Rate PAL 1 25f s NTSC 1 30f s The frame rate may vary due to different resolutions There are two options VBR and CBR Bit Rate Type yP Please note you can set video quality in VBR mode Recommended Recommended bit rate value according to the resolution Bit and frame rate you have se
47. t Bit Rate e In CBR the bit rate here is the max value In dynamic video system needs to low frame rate or video quality to guarantee the value e The value is null in VBR mode e Please refer to recommend bit rate for the detailed information Frame Here you can set the P frame amount between two frames The value ranges from 1 to 150 Default value is 50 Recommended value is frame rate 2 This function allows you to verify the video is tampered or not Here you can select watermark bit stream watermark mode and watermark character Default character is WatchnetCCTV The max length is 85 digit The character can only include number character and underline Watermark Sub Enable Please check the box here to enable extra stream stream function a This function is enabled by default General bit stream Bit stream type 15 Parameter Function C al mode There are three options H 264 main profile standard H 264B baseline standard encode and MJPG encode eo The H 264 and H 264B both are H264 bit stream H 264 is the Main Profile encode and the H 264B is the Baseline Profile encode mode H 264B is for Blackberry cell phone to realize the monitor You need to enable the sub stream function in your camera and set the resolution as CIF Then you can monitor via the Blackberry cell phone MJPEG In this encode mode the video needs to large bit stream to guarantee the video definition You can use t
48. this function The auto iris may change if the light becomes different When you disable this function the iris is at the max System does not add the auto iris function in the exposure control This function is on by default Some series product does not support this function It is to set the white balance mode It has effect on the general hue of the video This function is on by default You can select the different scene mode such as auto sunny cloudy home office night disable and etc to adjust the video to the best quality eo Disabled The white balance function is off The video will be output at the original color e Auto The auto white balance is on System can auto compensate the color temperature to make sure the vide color is proper Sunny The threshold of the white balance is in the sunny mode Night The threshold of the white balance is in the night mode Customized You can set the gain of the red blue channel The value reneges from O to 100 It is to set device color and the B W mode switch The default setup Is on Color Device outputs the color video Auto Device auto select to output the color or the B W video according to the device feature The general bright of the video or there is IR light or not B W The device outputs the black and white video Switch by periods You can se the day night mode switch time For example you can set the sunrise time as 06 00 00 and the sunset tim
49. vates motion detection channel to record once Channel alarm occurs working with motion detection function Please note you need to go to Storage gt Schedule to set current channel as general record Record Delay System can delay the record for specified time after alarm ended The value ranges from 10s to 300s Send Email If you enabled this function System can send out email to alert you when alarm occurs and ends e Here you can set PTZ movement when alarm occurs Such as go to preset x when there is an alarm e The event type includes preset tour and pattern Snapshot You need to input capture channel number so that system can backup motion detection snapshot file 4 3 2 2 Relay output The relay output interface is shown as in Figure 4 26 WatchiNEi Camera Relay Activation Network Event a gt video Detect gt Abnormity PA A Setup PA Relay out Storage System Information Figure 4 26 Please refer to the following sheet for detailed information 41 Parameter Function Alarm output There is only one output channel Please click the button 1 If you want to enable the alarm activation output function please press the corresponding button and then trigger Search alarm output status 4 3 3 Abnormity lt includes five statuses No SD card capacity warning SD card error and disconnection and IP conflict There are two interfaces for you reference See Figur
50. xit 36 Parameter Function Anti dither System only memorizes one event during the anti dither period The value ranges from Os to 100s Relay out Enable alarm activation function You need to select alarm output port so that system can activate corresponding alarm device when alarm occurs Some series product does not support this function Alarm Delay System can delay the alarm output for specified time after alarm ended The value ranges from 10s to 300s Some series product does not support this function Record System auto activates motion detection channel to record once channel alarm occurs working with motion detection function Please note you need to go to Storage gt Schedule to set current channel as general record Record Delay System can delay the record for specified time after alarm ended The value ranges from 10s to 300s Send Email If you enabled this function System can send out email to alert you when alarm occurs and ends e Here you can set PTZ movement when alarm occurs Such as go to preset x when there is an alarm e The event type includes preset tour and pattern Some series product does not support this function Snapshot You need to check the box here so that system can backup motion detection snapshot file 4 3 1 2 Video Masking The video masking interface is shown as in Figure 4 23 37 sone mm a WatchNEN Camera Motion Detect Network
Download Pdf Manuals
Related Search