600 WATT WIND TURBINE
Contents
1. 2 The height of installation should be 22 ft 7 m to 33 ft 10 m The wind speed below 22 ft 7 m constrained by the terrain is low and chaotic For example If winds in your area are more than 30 mph 13 4 m s the height of 7 m 1s recommended The higher the Wind Turbine stands more than 10 m the much stress your pole kit will sustain Also the Wind Turbine possibly brakes in extreme weather conditions Wind Speed Operating Environment A Operating Temperature 4 F 20 C 122 F 50 C B Operating Humidity lt 80 AAA C Average Wind Speed lt 30MPH lt 13 m s or lt 48KMH D Max Peak Wind Speed lt 45MPH lt 20m s or lt 70KMH E Elevation lt 1000m F Applicable Installation Height 8 85ft 33ft 2 7m 10m Health area for wind turbine 10m It is subject to IEC 61400 2 safety standards If the operating SS 7m temperature and wind speed exceed the above mentioned AJiaua puim Mo limits please turn on the manual brake in proper way to shut off the Wind Turbine 3 The rooftop may not be the best place for your Wind Turbine Here are three reasons a The flow is more turbulent above the rooftop and leads to the low wind power availability b The stress the pole kit sustains varies in rooftop constructions The evaluation and stability cannot be guaranteed c The slight noise and vibration still affect sleep for some sensitive people and2. Will it affect the regulation of my 600 Watt Wind Turbine to install an RF radio frequency filter An RF filter should not affect the regulation of the Turbine but any electronic devices placed in line with the turbine must be rated for the proper current and voltage It is best to place any line filters on the power lines for the load device that requires it and as close to the device as possible Trouble shooting You may require an extra person to assist with these tests 1 Remove the blade hub from the turbine Replace the rotor hub nut on the rotor shaft 2 Quickly spin the rotor shaft manually with your fingers while connecting and disconnecting the red and black wires turbine must not be connected to batteries 3 With the red and black wires connected to each other the shaft should be more difficult to turn When the wires are disconnected it should spin freely Should this not be true please contact supplier or manufacturer 4 With your 600 Watt Wind Turbine connected to your battery bank use an electric hand drill to spin the rotor shaft 5 Below 500 RPM the rotor should spin freely without friction 6 At 500 RPM and above the Wind Turbine should be charging the battery You should feel resistance on the rotor shaft 1f the shaft 1s not rotating contact your turbine dealer or manufacturer Be aware your battery banks needs to be under 12V or 24V for this testing as the Turbine needs to read a charge Warranty We w
3. MPPT brake or mechanical stop switch 3 Listen to your Turbine should you hear any mechanical noise maintenance may be required please contact The Products Customer Service 4 After installation re adjust and tighten the screws and bolts 5 Adhere to proper grounding techniques as established by the NEC 6 Your Wind Turbine must be installed in accordance with this manual and local and national building code Incorrect installation may void your warranty 7 Wind turbine blades spin at a potentially dangerous speed this must be respected Never approach a turbine in motion 8 Note wire size gauge chart included prior to wiring Any under sizing of wire can be potentially dangerous 1 1 Mechanical Hazard Rotating blades present the most serious mechanical hazard The rotor blades are made of very strong thermoplastic At the tip the blades may be moving at velocities over 15m s At this speed the tip of a blade is nearly invisible and can cause serious injury Under no circumstances should you install the turbine where a person could come in contact with moving rotor blades 1 2 Electrical Hazard The 600W Turbine 1s equipped with sophisticated electronics designed to provide protection from electrical dangers Please note that the inherent personal dangers from electrical current still exist therefore caution should always be used when connecting this and other electrical devices Heat in a wiring system 1s often a result of too m
4. as copper The 600 Watt Wind Turbine uses copper or tinned copper for the yaw wires 8 What battery should I choose for my 600 Watt Wind Turbine There are multiple battery options in today s market flooded lead acid absorbed Glass mat AGM gel cell and NiCad There is no definitive choice for your alternative energy needs Normally the choice of battery 1s determined by availability and pricing Should you have questions regarding batteries please consult a local battery supplier Or view www batterycouncil org The capacity of your battery bank is determined by your use Below is a good guideline e 12 volt systems 400 Amp hours e 24 volt systems 200 Amp hours 16 Possible Battery Configurations suggested 12 24 VOLT BATTERIES IN PARALLEL 9 Is lightning protection necessary You should ground your 600 Watt Wind Turbine Proper grounding illustrated below provides protection to individuals and equipment by eliminating the possibility of dangerous voltage Remember a steel tower is a conduit for lightning Every wind turbine and turbine tower needs to be grounded at the tower base even though the system may be grounded at the battery bank Grounding the tower at its base may help prevent shocks to persons touching the tower due to lightning or electrical faults Please take the time to review the National Electrical Code NEC and local building and zoning regulations for complete requirements Even in Off
5. has 30 days to return the product Failure to deliver the product within the 30 days results in the RA as no longer being valid and a new RA must be issued Manufacturer is under no obligation to accept any product that is returned to them without a proper RA 20 Limitation of Liability UNDER NO CIRCUMSTANCES WILL THE MANUFACTURER OR ITS AFFILIATES OR SUPPLIERS BE LIABLE OR RESPONSIBLE FOR ANY LOSS OF USE INTERRUPTION OF BUSINESS LOST PROFITS LOST DATA OR INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND REGARDLESS OF THE FORM OF ACTION WHETHER IN CONTRACT TORT INCLUDING NEGLIGENCE STRICT LIABILITY OR OTHERWISE RESULTING FROM THE DEFECT REPAIR REPLACEMENT SHIPMENT OR OTHERWISE EVEN IF THE MANUFACTURER OR ITS AFFILIATE OR SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE Neither the manufacturer nor its affiliates or suppliers will be held liable or responsible for any damage or loss to any items or products connected to powered by or otherwise attached to the hardware The total cumulative liability to Customer from all causes of action and all theories of liability will be limited to and will not exceed the purchase price of the Product paid by Customer This warranty gives the Customer specific legal rights and the Customer may also have other legal rights that vary from state to state or province to province 21 Appendix A MECHANICAL STOP SWITCH The MPPT controller has an integrated ba
6. mph 6 m s average wind speed sites Bearing life will vary from one application to another however you should expect at least a five year performance in adverse conditions and 10 years in normal conditions 4 Can the 600 Watt Wind Turbine be connected in reverse polarity to the battery without causing any damage 15 Reverse polarity will cause damage to both your MPPT controller and battery 1f not quickly remedied Always double check any wiring to reduce the risk of reverse polarity Your turbine 1s equipped with polarity protection to reduce the risk of damage but it is still possible to degrade your wiring and cause damage to the overall system 5 Will it hurt my 600 Watt Wind Turbine to short circuit the output No the 600 Watt Wind Turbine is designed to be short circuited as a normal shutdown procedure by a fuse The function of the stop switch is to both disconnect the turbine from the batteries as well as short circuit the output of the turbine 6 Where can I locate tubing to make a tower Your 600 Watt Wind Turbine is designed to make mounting as simple and straightforward as possible Should you not wish to purchase the custom tower kit feel free to utilize schedule 40 1 5 inch steel tubing This should be available through your local hardware outlet 7 What 1s the difference between copper and aluminum wire Generally aluminum wire is less conductive so it must be bigger for the same amp load and resistive losses
7. will lose overall balance resulting in a decrease in efficiency Should you notice damage to the blades you must replace all 3 The blades are balanced as sets e Check the blade bolts and the hub nut for tightness e Check nosecone for cracks and tighten nuts e Wipe any excess dirt build up from the blades e Check all electrical connections to make sure they are tight and free from corrosion e Check the voltage of your battery bank with a Multi meter and clean the terminals e We suggest replacing the blades every five years for optimal performance 7 FAQS 1 How does the 600 Watt Wind Turbine control power and RPM in high winds Your Turbine s operation will be halted to reduce the risk of damage due to overcharge and over spin of the rotor blades This process of braking is handled internally through your Turbines electronics 2 What is the maximum wind speed the 600 Watt Wind Turbine will survive and do I need to take it down in a storm Your wind turbine is designed to operate in most climatic conditions Should you expect or experience winds of 1SOMPH upwards please turn off the MPPT controller which will in turn manually apply the braking system to protect from any over spin Once the Turbine has stopped it 1s possible to lay down the Tower to offer further protection 3 How long will the bearings or other wearing parts last According to engineering calculations the bearings should have a 10 year life span in 12
8. 600 WATT WIND TURBINE User s Manual TABLE OF CONTENT PP PE E e o EOI l kt Mechamcat Hazi dinas tora E E EE ca ae EAE EEE l lA E E E E E E E E E ET A E E E A E l 2 IMODEIZAND SPECIFICATION TAB LE en i o ae EE AA OETA 3 2 MaDe C MIC AOU TADI peronon em den EEEN dd 3 2 2 Performance A SE Messe seen listes anses A oon Soon 4 3 DIGITAL CONTROLLED MPPT WIND POWER CHARGER 4 Sh System Wine Diarani ds ide AA eee pas ow SHS ees 5 ts PACKAGE CONTENIDA Eo Pool 9 d INSTALLATION RPOCEDURE cacera aa oia 10 O MAINTENANCE sr ai delicia 15 Te FAQS AA AAA AAA ARANA RIAS AAA ARAS ARANA 15 TROUBLE SHOOTING ciar SAS AA a Rene 19 WARRANT O 19 APPENDIX MECHANICAL STOP SWITCH rica 22 APPENDIX B IMPORTANT SAFETY INSTRUCTIONS 8 23 APPENDIX C BEAUFORT WIND SCALDE erinra nent ioda ion ions 24 1 SAFETY Your 600 Watt Wind Turbine is designed with your personal safety as the first priority However there are still some inherent dangers involved with any electrical and or mechanical equipment Safety must be the primary concern as you plan the location installation and operation of the turbine Please read the following Important Safety Instructions Please take the time to read through this manual prior to assembly 1 Place this instruction manual in a safe place for reference 2 Wait until a calm day to install or perform maintenance on your Turbine with activation of
9. Grid Systems there are multiple ways for tower grounding the most common method is a copper clad steel electrode s driven into the soil Please view the following grounding diagram nn rai Tower we F Cable Ciamp r Grounding Conductor 6 AWG Min Must be secured and buried for protection _ Grounding Wire Clamp Grounding Rod gt A Existing Grade Foundation A ai di 10 What effect does radio interference have on my 600 Watt Wind Turbine The internal circuitry of the 600 Watt Wind Turbine is shielded and filtered to prevent radio interference and has been tested to insure electro magnetic compatibility 11 What effect does my 600 Watt Wind Turbine have on radio transmissions The 600 Watt Wind Turbine normally does not affect radio transmitters Care should be taken however to route power lines from the 600 Watt Wind Turbine away from the power and antenna lines of a radio transmitter An old ham radio operator s trick 1s to twist positive and negative wires together to provide an even distribution of EMF noise across both wires which serves to cancel out the electrical noise created 18 This technique can be used on the 600 Watt Wind Turbine power lines on the radio s power lines and on transmission wires Transmission lines should always be kept as far from power lines as is practically possible Proper grounding of the Turbine and other system components must also be observed 12
10. SSED WARRANTY SET FORTH ABOVE THE MANUFACTURER DISCLAIMS ALL OTHER EXPRESSED AND IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OR FITNESS FOR A PARTICULAR PURPOSE MERCHANTABILITY AND NON INFRINGEMENT NO OTHER WARRANTY EXPRESSED OR IMPLIED WHETHER OR NOT SIMILAR IN NATURE TO ANY OTHER WARRANTY PROVIDED HEREIN SHALL EXIST WITH RESPECT TO THE PRODUCT SOLD UNDER THE PROVISIONS OF THESE TERMS AND CONDITIONS THE MANUFACTURER EXPRESSLY DISCLAIMS ALL LIABILITY FOR BODILY INJURIES OR DEATH THAT MAY OCCUR DIRECTLY OR INDIRECTLY BY USE OF THE PRODUCT BY ANY PERSON ALL OTHER WARRANTIES ARE EXPRESSLY WAIVED BY THE CUSTOMER Warranty Claims amp Return Policies To be eligible for service under this warranty customer must either contact manufacturer either through written request or by telephone to submit a service request for the wind turbine covered by this warranty within specified period 1 year from original date of purchase and request a return authorization RA number This RA must be issued before any product can be returned All notifications must include the following information a Description of alleged defect b How the wind turbine was being used c Serial d The original purchase date e Name phone address of party requesting warranty Within 2 to 3 business days we will provide the customer with an RA and will direct customer to location where the product is to be returned Once an RA has been issued the customer
11. ale 7 Please refer to Appendix A for detailed information
12. animals 4 Check the manual brake health periodically We suggest that the users turn on the manual brake of MPPT to see if the speed is getting low Meanwhile the RED LED should be illuminated once the manual brake is turned on If you hear the sound of the relay it means the MPPT works normally 5 Check the three wires from the Wind Turbine output periodically Please use a current clamp meter to measure AC current If the outputs are not consistent please contact the distributor for further instruction For safety reasons please stop operating your Wind Turbine 6 Check the battery health periodically The abnormal battery and improper connection will cause over spin issues The Wind Turbine s operation should be halted to reduce the risk of damage due to over spin of the rotor blades 7 Survival wind speed means that the wind turbine will survive 157 MPH 250 KMH when the manual brake is turned on Exceeding this stated wind speed will result in wind turbine failure and collapse 23 Appendix C BEAUFORT WIND SCALE Beaufort No Description Calm Avg Wind Avg Wind Avg Wind Image Speed knot h Speed km h Speed m h Light air 0 55 1 66 3 13 19 Moderate breeze 20 30 3 61 5 27 MCE Dome e car Gentle breeze 17 5 20 83 ml om oe It is strongly advised to manually turn on your Mechanical Stop Switch during periods of high winds upwards of Beaufort Wind Sc
13. arrant your product to be free from defects in material and or workmanship for a period of 1 year from original date of purchase Warranty coverage is extended only to customer original purchaser If product proves defective during warranty period manufacturer at its option will 1 Replace wind turbine with new or refurbished product 2 Correct reported problem Customers warranty continues to be valid on repaired or replaced product from original warranty date Restrictions This warranty covers defects in manufacturing discovered while using the product as recommended by the manufacturer The warranty does not apply to a equipment materials or supplies not manufactured by 19 manufacturer b Product that has been modified or altered other than by manufacturer or without prior manufacturer s approval c Has been exposed to winds exceeding 157mph d Windstorms upwards of Beaufort Wind Scale 7 lightning and Hail damage e Repairs performed by other than authorized support staff f All acts of God misuse negligence or accidents g Tower foundation and wire has not been installed operated repaired or maintained in accordance with the instructions supplied by manufacturer Any service identified in the above list or product 1s found not to have any defect in manufacturers workmanship or materials the customer will be responsible for the costs of all repairs and expenses incurred by manufacturer Disclaimer EXCEPT FOR THE EXPRE
14. bine depending on your power requirements and available components Single Turbine installation Please apply the Mechanical Stop Switch simultaneously Refer to Page 22 Appendix for detailed info 600W Wind a Turbine 30 Amp Meter a Tower Battery Turbine Red Lead Black Lead Blue Lead Positive Battery Negative Multiple Turbine installation Please apply the Mechanical Stop Switch simultaneously Refer to Page 22 Appendix for detailed info N 600W Wind 600W Wind 600W Wind Turbine Turbine Turbine A m T 7 T o H jg v al 2 5 o B 8 24 414 eo 4 ES E 3 gt u D D Oo lt lt 5 ol 3 59 al Sil sis e SlIT Slim Ee Sisal po mia e aja e aja D a a 2 E y E En Eb T D En E As T a 30 Amp Meter Battery Battery Hybrid Solar Wind System Please apply the Mechanical Stop Switch simultaneously Refer to Page 22 Appendix for detailed info 600W Wind Turbine 4 12V or 24V 14 Solar Array A p Solar Change Controller 30 Amp Meter Tower Turbine Red Lead Black Lead Blue Lead Positive Negative A typical hybrid system Photovoltaic and Wind combined is wired as follows whenever feasible wire the turbine and solar panels to their own set of battery terminals 4 PACKAGE CONTENTS Check the parts listed with
15. r of your installation Should the turbine continue to spin check your terminal connections Do not approach the turbine without activation of this mechanical stop switch under any circumstance Notes e It is not necessary to apply MPPT brake during activation of the mechanical stop switch e eat e It is strongly advised to test both mechanical 7 and MPPT stop switch periodically ad e Your mechanical stop switch is pre wired with 10 AWG wire this should not be altered e The mechanical stop switch should be placed close to your MPPT in a dry ventilated environment e For multiple turbine applications please use one mechanical stop switch for each wind turbine e This mechanical stop switch has been designed specifically for your Wind Turbine it should not be incorporated into other models 22 Appendix B IMPORTANT SAFETY INSTRUCTIONS Read these instructions below before installing your Wind Turbine to ensure people and property against accidents Please also make sure it is set up under environmental and operating conditions 1 Locate your Wind Turbine in windy sites so as not to disturb neighbors and animals around The noise and vibration element cannot be got rid of even 1f Wind Turbine offers the lowest noise than any others on the market The better location of your Wind Turbine requires avoiding personnel or animal activities within a 33 ft 10 m radius and human habitation and wildlife within a 66 ft 20 m radius
16. s 12 volt System AWG Metric Wire Size mm Turbines 0 9 m 9 18 a 18 27 27 46 m 46 58 ite 58 76 m 76 95 m 95 119 m 119 152 bi a enome 616mm 4 26 mm 2 85 mn 1 60mn 0 60 mn 00 70 mn 000 00 mme 000 90 mm 2 erie 425 nn 1 80m 00 70 ms 00m a gt C a rme 2 35 mms 0 50 000 90 mn 00007120 mm ff RR If your system requires this length of wire consider using parallel wires 24 volt System AWG Metric Wire Size mm Number of 0 30 ft 30 60 ft 60 90ft 90 150 ft 150 190 ft 190 250 ft 250 31 Oft 310 390 ft 390 500ft Turbines 0 9 m 9 18 m 18 27 m 27 46 m 46 58 m 58 76 m 76 95 m 95 119 m 119 152 m AS 14 25 mm 12 4 mm 10 6 mm 8 10 mm 616mm 425mm 4 25mm 000 90 mm 000 90 mm 12 4 mm 8 10 mm 6 16 mm 4 25 mm 4 25 mm 2 35 mm 2 35 mm 1 50 mm 0 50 mm BE 10 16 mm 810mm 66mm 425mm 2 35mm 2 35 mm 1 50 mm 0 50mm 00 70 mm System protection see also included manual Your MPPT charge controller comes equipped with state of the art overcharge protection Temperature of the internal circuitry is moderated by an internal fan that is activated at 45 C 110 F When the temperature of the MPPT exceeds 65 C 150 F your MPPT will automatically apply both the internal fan and braking system to your Wind Turbine to prevent damage 3 1 System wiring diagrams There are multiple options to connect your Wind Tur
17. sten the bolt by using the hex wrench Caution 1 Ensure that rubber spacer is attached to the tower pole prior to turbine installation otherwise the turbine will be overtight and unable to sustain vibrations Any product damage caused by operations without rubber spacer is not included in the warranty as well Caution 2 Owing to the base of the turbine the outside diameter of the iron pipe should be 48 3mm to 48 6mm and the wall thickness should be 1 9mm at least 1 1 2 Pipe 48 3mm Diameter Wall Thicknss at least 1 9mm Figure 7 12 Step 6 Install the hub on the wind turbine using M14 nut and spring washer Figure 8 Figure 9 Caution Make sure the nut ts secured with the spring washer Step 7 Put the sleeve inside the nose cone and fasten the nose cone to the hub Apply pressure to the connections to ensure a secure fit Figure 10 Figure 12 13 Step 8 Final product diagram Figure 13 6 MAINTENANCE Your 600 Watt Wind Turbine has been designed to run for long periods without requiring any maintenance Performance will be enhanced 1f you periodically inspect your system Review the following simple maintenance procedures and implement every six months Caution Do not go near the wind turbine during operation Caution The blades are sharp Please handle with care e Check blades for superficial damage Replace blades if damaged It is important to not use blades that are damaged as you
18. the contents of the box and make sure that you have everything needed for assembly Figure 1 _ Vertical Stabilizer Generator P Blade Nose Cone Base _ Caution The edges of the blades are sharp Please handle with care Name A Inverse tooth Nut M14xP2 0 Hex Screw M6XL40 a Nut M6 KE Hex Screw M5XL50 Washer M14 Washer M6 Hex Key no 5 Accessory Pack Hex Key no 3 Rubber Spacer Hex Screw M5XL20 Spacer for Vertical Tail Inverse tooth Nut M14xP2 0 Hex Screw M6XL40 Nut M6 Hex Screw M5XL50 Washer M14 Rubber Spacer Hex Screw MSXL20 Washer M6 Hex Screw M6XL35 2 Replacement Accessory Pack 5 INSTALLATION PROCEDURE Step1 Open box to ensure all parts are present remove the hub from the box Figure 2 10 Step 2 Take out the blades from box and fasten the blades on the hub with nuts Figure 3 Figure 4 Caution Make sure that all of the bolts are secured with nuts Step 3 Re us Use the four supplied spacers and HEX screws to firmly connect the Tail Fin to the hub Figure 5 11 Adhesive strip should be wrapped around your Tower not included to increase secure connection to the Yaw shaft Step 4 Take out the wind turbine from box and put the cables through the mast Figure 6 Step 5 Attach a rubber spacer to your chosen tower not included To install the wind turbine to the tower and securely fa
19. ttery controlled braking mechanism This is explained in your MPPT manual Further to this protection we have incorporated a secondary level of safety and convenience with a mechanical 3 phase AC brake During periods of high winds upwards of 30 mph 13m s it is strongly advised to utilize your MPPT brake and your mechanical stop switch The use of your mechanical stop switch will not affect the voltage of your battery We strongly advises the activation of the mechanical stop switch during any maintenance of or around your 600 watt turbine This will prevent the blades spinning and voltage to be transferred Likewise during initial installation please activate the mechanical brake The final step in installation of turbine controller and battery should be release of this mechanical stop switch The mechanical stop switch is pre wired for your convenience with 10 AWG wire and battery terminal connections The wire configuration is explained in the diagram below fig 1 Place the corresponding wires red black blue from the mechanical stop switch into the MPPT input terminals This should match the similar colored wires from your turbine Your turbine and stop switch share input terminals on the MPPT This provides a parallel connection Test the connection of your mechanical stop switch at the point of initial installation Push the brake ON You should see the turbine stop its rotation Continue to apply this brake during the remainde
20. turbine will survive 157 MPH 250 KMH when the manual brake is on Exceeding this stated wind speed will result in wind turbine failure and collapse 2 2 Performance specifications The following power curve shows the performance you should expect from your wind turbine During smooth steady wind speed you can expect to see output resembling the curve illustrated below To convert between power and current use the following formula POWER VOLTAGE x AMPS Power output W 6 a 10 Wind speed m s 3 Digital controlled MPPT Wind Power Charger Please see included Manual for your MPPT Charge Controller 4 MCU fully digital controlled MPPT wind power charger 24 SEPIC conversion large DC input voltage range 24 Smart load management function braking function Rated Output Power 600W Max Battery Voltage Range 12V or 24V DC Input Voltage Range 5 75 Vrms Charger Efficiency Battery Protection Voltage 12V 14 4V Lead acid batteries or 15 8V Deep cycle batteries 24V 28 8V Lead acid batteries or 30V Deep cycle batteries Rated Load Current 35A Max Over Speed Braking lt 1400 rpm Caution Please review the following wire gauge table to install the correct wire gauge We recommend these as the minimum wire sizes for optimal performance Always use the largest gauge wires that are practical and affordable Local state and or national electrical codes take precedence over these general recommendation
21. uch current flowing through an undersized wire or through a bad connection Please consult wire guide table below Batteries can deliver a dangerous amount of current If a short circuit occurs in the wiring from the batteries a fire can result In order to avoid this threat a properly sized fuse or circuit breaker 1s required in the lines comnecting to the battery Choosing your 600 Watt Wind Turbine s location Prior to the mounting of your 600 Watt Wind Turbine you must carefully consider a location Things to consider when thinking about your location A Distance from any obstacles that will cause turbulence trees buildings etc B Distance from MPPT controller and battery bank C Any local zoning restrictions D Clearance of power lines In general terms the higher the tower the less obstruction to air flow leading to a more efficient charge capacity The minimum recommended tower height 1s 30 ft or 20 ft above nearby obstructions as shown below Prevailing wind Cl q 2 MODEL AND SPECIFICATION TABLE 2 1 Specification Table 600W Turbine Rated speed 12 5 m s 41 ft s Rated power 600W Voltage with MPPT 12 or 24V 131 m 4 2 f Cut in wind speed 4 5 MPH Survival wind speed 157 MPH Number of blades Blade material Fiber glass Suggested battery capacity gt 100 A Hr The manual brake should be turned on when the wind speed upwards 30 MPH 48 KMH Survival wind speed means that the wind
Download Pdf Manuals
Related Search