Home

9485/9487 - Steven Engineering

1. System Power It is always a good practice is to use isolation transformers on the incoming AC power line to the 9485 9487 An isolation transformer is especially desirable in cases in which heavy equipment is likely to introduce noise onto the AC line The isolation transformer can also serve as a step down transformer to reduce the incoming line voltage to a de sired level The transformer should have a sufficient power rating units of volt amperes to supply the load adequately Proper grounding is essential to all safe electrical installations Refer to the National Electric Code NEC article 250 which provides data such as the size and types of con ductors color codes and connections necessary for safe grounding of electrical compo nents The code specifies that a grounding path must be permanent no solder continu ous and able to safely conduct the ground fault current in the system with minimal im pedance The following practices should be observed e Separate ground wires from power wires at the point of entry to the enclosure To minimize the ground wire length within the enclosure locate the ground reference point near the point of entry for the plant power supply e All electrical chassis and machine elements should be grounded to a central ground bus normally located near the point of entry for the plant power supply of the enclo sure Paint and other nonconductive material should be scraped away from the area whe
2. Exit View Returns to the Main Menu Allows viewing the macro for the selected key without having to worry about an accidental change to the macro When View is chosen the Exit option and the state of the click clicks are not supported on the 9485 9487 are displayed on the menu bar and a graphic representation of the chosen keypad is shown Select Exit from the View Menu to return to the Macros Menu To select a key to view use the arrow keys to position the cursor on the desired key and press ENTER The macro is displayed as two lines ASCII and code The ASCII line displays each keycode as the keys 1t represents on the full stroke keyboard Special la bels are used for certain keys e g Spe for space bar UAr for up arrow and bk for the break code prefix The code line is displayed in either hex or deci mal as explained below There is a one to one correspondence between the ASCII and code lines to help you interpret the code line The menu bar displayed while viewing the macro offers two options Exit and Hex Decimal Exit Returns to View menu Hex Decimal Toggles between displaying the macro in hex or deci mal format Default is Hex When Hex is chosen the keycodes are displayed as they are in memory hexa decimal value scan codes When Decimal is chosen the keycodes are displayed as the decimal equivalent of the hex codes For example the macro abe would be displayed as 1C FO 1C 32 FO 32 21 FO 21 in hex and
3. Floppy Disk Keyboard Port Access There are two display choices a 256 color STN LCD dual scan 9485 or 256 color CCFT TFT LCD 9487 all protected from breakage by an im pact resistant shield If a touch screen is factory in stalled the impact resistant shield is replaced by the touch screen which is backed by tempered safety glass The 20 sealed function keys are located directly below the display They provide the user with easy access to familiar PC software routines The func tion keys are programmable as well as relegend able to enable you to customize your keypad key codes This sealed 32 key numeric keypad includes the following keys for data entry ESC SHIFT CTRL ALT DEL PAGE UP HOME INSERT PAUSE PAGE DOWN END SPACE BACK SPACE up down left and right arrows and numbers 0 9 The top three rows 15 keys on this keypad are relegendable Located below the keypad this door accesses the floppy disk drive and keyboard port The keyboard port located just above the disk access allows a PC keyboard to be interfaced with the system Note The access door must be closed and latched to maintain the NEMA seal Warning In order to maintain a safe condition an external keyboard cannot be used when the unit is operating in a hazardous environment System Status LEDS The front panel features six status LEDs Three are wired to hardware Power Disk and COM The remaining three Mainten
4. Depth 5 62 142 75 Figure B 3 9485 9487 System Cutout Dimensions Note A full size template is available from Xycom s Application Engineering Department Appendix B Block Diagram B 3 Appendix C Pinouts This appendix describes the pinouts for the keyboard speaker jack COM1 COM2 and VGA connectors Keyboard Connectors Two standard five pin keyboard connectors are available on the 9485 9487 Figure C 1 illustrates the pin locations O3 10 oO 2 O Front View Figure C 1 Keyboard Connector Pin Locations Table Appendix C 1 describes the pinout Refer to figures 3 1 and 3 3 for the location of these connectors Table Appendix C 1 Keyboard Pinouts 9485 9487 Manual COM1 COM2 Serial Port Connectors The COM1 and COM2 serial ports are standard DB 9 connectors located on the I O side of the unit see Figure 1 4 Table Appendix C 2 COM1 COM2 Serial Port Pinouts DCD1 RXD1 TXD1 DTR1 GND l6 DSR RTS1 18 CTS1 R4 A HE VGA Connector VGA The VGA connector is a 15 pin subminiature located on the CPU board Refer to the CPU manual for more information Table Appendix C 3 VGA Pinouts Pin 9 KEY NC 5 GND_ 1 6 GND 7 GND_ HYSNC 13 HYSNC GND VYSNC 15 NC GND 15 NC Appendix C Pinouts Parallel Port Connector LPT1 The parallel port connector LPT 1 is a 25 pin female D subminiature connector loc
5. lt 4 gt move the cursor left up down and right Press ENTER to validate your selec tion e ESC exits the menu You are prompted to save changes e F5 selects the previous or smaller value 9485 9487 Manual F6 selects the next or higher value F9 automatically configures the system with the default values These values are de fined by the system configuration and the values are set in the Setup Menu F10 loads previous values Quadtel BIOS If the CPU board has a Quadtel BIOS press CTRL ALT S simultaneously after the post RAM test has completed to access the Setup Menu Make changes by following direc tions on the screen Press F10 to save the Setup and ESC to exit Refer to your CPU manual for more information on the Setup Menu Preparing for the Tests 2 2 To test your system you need the following equipment Xycom System Test Disk bootable 3 5 inch DS DD disk Xycom part number 99290 001 IBM PC AT compatible keyboard Xycom part number 91971 001 or equivalent Centronics compatible printer cable Parallel printer Centronics style interface Two serial loopback test connectors refer to Figure Chapter 2 1 for pinouts Formatted scratch disk 3 5 inch DS HD Perform the steps below before starting the system tests 1 Place the CPU board jumpers and switches to the factory set positions Refer to your CPU manual for these settings Plug the female end of the AC power cable into the side of the
6. 12 VDC 45 A Total not to exceed 42 watts Total not to exceed 35 watts EIA standard 19 panel Flat Panel 10 4 STN dual scan color LCD display 9485 E 10 4 TFT high brightness CCFT color display 9487 Agency Approvals UL 508 1604 if configured for hazardous locations CUL C22 2 No 14 213 if configured for hazardous locations im EN 60950 Regulatory ee rec 47 CFR Part 15 Class A EN55022 1994 Class A IEC 801 2 1991 8 kV CD 15 kV AD IEC 801 3 1984 27 500 MHz 10 V m IEC 801 4 1988 1kV Signal 2kV AC 9485 9487 Manual Table Appendix A 2 Environmental Specifications Characteristic Specification Temperature Operating STN Color display 9485 TFT color display 9487 Non operating Humidity Operating Non operating Altitude Operating Non operating Shock with no rotating media Operating Non operating Vibration with no rotating media Frequency Operating Non operating 0 to 50 C 32 to 122 F 0 to 50 C 32 to 122 F 20 to 60 C 4 to 140 F Note On 133 and 200 MHz systems with Pentium processors the CPU may be moved to slot one to obtain a total of three expansion slots If this is done you must derate the temperature specifications by 5 C 20 to 80 RH non condensing 20 to 80 RH non condensing Sea level to 10 000 feet 3048 m Sea level to 40 000 feet 12192 m 15 g peak acceleration 11 msec duration 30 g peak acceleration 11 msec duration
7. 28 240 28 50 240 50 33 240 33 in decimal Chapter 4 Programmable Keyboard Interface Module Teach Allows you to record key strokes into a macro When Teach is selected a graphic representation of the keypad currently in memory is displayed Menu bar choices are Exit ASCII Hex Decimal and Click ON OFF Exit Returns to Macros menu ASCIVHex Decimal Chooses the format to display the keystrokes as they are entered Default is ASCII Click ON OFF Not supported on the 9485 9487 To select a key to define use the arrow keys to position the cursor on the de sired key and press ENTER After a key is selected the utility records every key stroke on the external full stroke keyboard into a macro to be assigned to the chosen key As the keys are entered they are displayed using the chosen format ESC is used to stop recording and return to the Teach Menu so it is not a recordable key However ESC can be included in a macro by using the edi tor Note The changes made to the macros in the Teach Menu are not pro grammed until you select Download Edit Displays a graphic representation of the keypad in memory and a menu bar displaying Exit and Click ON OFF Exit Returns to the Macros Menu Click ON OFF Not supported on the 9485 9487 To select a key to edit use the arrow keys to position the cursor on the desired key and press ENTER In edit mode the macro is displayed as two lines The top line the edit line displays the
8. 4 7 Download Men tsscsacsckecheaedssexsdhatarced tailandia aa aaa idad tire tit 4 7 A RS 4 7 COS OST TE A ER A A AE 4 8 Chapter 5 Maintenance ooommccccconnncncnnnnnnnnnnnnnnnnnnnnnn rre 5 1 Preventive Maintenances es a tia 5 1 Routine Maintenance isaac 5 1 Replacingthe FUSE ciuda o a 5 2 Replacing the Slide out Computer Module occcoconnccccnoncccccnonoccconnnnccnononaccnnnnnnccnnnnnncnnonnnnccnnnnnnccnns 5 2 Replacing the Fan Eller aaron 5 3 AO O 5 4 Product Repair Program Returning a Unit to XyCOM occcoconcccconcnnccccnnnnccnnnnnncccnnnanccnnnnnncrnnnnnnccnnnnnnccnns 5 5 Keyboard ConmeCtors oi an serene cueadacetinreer ee aice shea Eras C 1 COM1 COM2 Serial Port Connectors ecs ansionsa era Eea eA EAEE e CESANA EREE AERIANA AAKA AS ALEAR C 2 VGA Connector VGA sicsccitiissccactsitcorbiearconcthtscegaedtncuediestcagbbettaussigds cada ihaeediautcoubenatayeeiatnecaenttaedss C 2 Parallel Port Connector LP Tia oia C 3 Speaker Jack Connectoren i ena aE ci tada Rev de is C 3 Appendix A Technical Specifications ccccccceeeseeeeeeeeeeeeeeeeeeeeeeeseeeeeeeseeeeneeseeeaeeeseeeeeeeneeeseees A 1 Appendix B Block DiaQramns c 22 lt c e s2cs2 ccnscecccarzac lt eateeansceagcceseqesecnetasccadseccaaenecesacaesecoudeucassecnteeces B 1 Appendix C Pinouts Keyboard COnmeCtors vss sscccectanceedaenececautanes tardor AAEE AE E daria detuavcheaesa ner day C 1 COM1 COM2 Serial Port Connectors cece cece c
9. 5 to 2 000 Hz 006 15 mm peak to peak displacement 1 0 g maximum acceleration 015 38 mm peak to peak displacement 2 5 g maximum acceleration Front panel impact specification Designed to meet UL1418 Appendix B Block Diagram KEYPAD FUNCTION KEYPAD FLOPPY DRIVE AC POWER SWITCH CONTROLLER SERIAL TOUCH SCREEN TOUCH SCREEN KEYBOARD FRONT PANEL HARD DRIVE AC POWER SUPPLY ASSY BACKPLANE AC INPUT MODULE DC POWER SUPPLY POWER SWITCH FUSE HOLDER Figure B 1 System Block Diagram FLAT PANEL DISPLAY INVERTER KEYBOARD VO PANEL EXT BAT DC INPUT MODULE B 1 9485 9487 Manual Note Material 010 thk Aluminum with 090 thick domes Epoxy resin on the front side and 3M 468 adhesive on the back side 0 042 1 07 R 0 83 17 50 22160159 NOTE All dimensions are in inches mm Figure B 2 9485 9487 Logo Dimensions 0 25 6 35 diam hole 14 req d 0 23 5 84 3 156 80 16 gt 6 00 152 4 6 00 152 4 0 34 8 64 gt je F E 3 50 88 90 17 625 447 68 2 25 57 15 11 45 290 83 Depth listed does not account for any cabling that may extend 11 00 279 40 beyond the unit Torque 10 32 mounting nuts to 3 50 88 90 25 inch lbs 2 8 Nm 28 Kgf cm o 0 23 5 84 1 10 27 94 18 312 465 12 All dimensions are in inches mm
10. 9 drivers video 3 11 E EEPROM 4 8 enclosures hazardous locations installations 3 23 environmental specifications A 2 excessive heat 3 14 excessive line voltage 3 15 excessive noise 3 15 extender cable installation 3 9 F fan filter 3 5 maintenance 5 1 replacement 5 3 features optional 1 2 standard 1 1 floppy disk access 3 4 floppy disk drive 3 2 function keys 3 2 fuse replacement 5 2 H hardware specifications A 1 hardware options external 3 9 internal 3 8 hazardous locations installations 3 19 definitions Class I locations 3 21 Class II locations 3 21 Division 1 locations 3 22 Division 2 locations 3 22 groups 3 22 Index 2 Index enclosures 3 23 operation and maintenance 3 25 power switch 3 24 hazardous locations installations cable connections 3 24 heat excessive 3 14 hex scan codes programmable keyboard interface module 4 9 T O panel 3 5 IDE hard drive setup information 3 4 installation 8x14 font TSR 3 10 9000 RAD card 3 8 CPU into a chassis 3 17 DRAM 3 9 extender cable 3 9 external hardware options 3 9 hazardous locations 3 19 internal hardware options 3 8 keyboards 3 9 MS DOS 3 10 panel 3 13 PC AT boards 3 16 serial mouse 3 10 SIMMs 3 9 video drivers 3 11 internal hardware options installation 3 8 K keyboard installation 3 9 port 3 2 programmable 4 1 keyboard connectors C 1 keyboard port 3 5 keypads data entr
11. EEE AAR EAE AA AA AEEA NEE A ENARE AANS 3 14 Excess WENGIS Oiar ea E A E EE A E 3 15 EXCOSSIVE LIne VO aio 3 15 Mounting Ihe 9489 948 Trs rrene nd obagane Aaa AAA A 3 15 Installing PEAT BoOandS orrie iiaiai a EEE RAA AEEA EAER EATE DaS 3 16 Installing the CPU into a ChasSiS oooocccccooncccnnnnncccnnnnnccnnnnnnccnnnnnncrnnnnnncrnnnnnnnrnnnnnnnrnnnnnnrrnnnnnnrrnnnnnnens 3 17 9485 9487 Manual Available POWE Ninenin a aa a a ee A cbi at ine Mae edad iaw shee sled ce ieee ieee E EA 3 19 Hazardous Locations Installations 0 cccceceeeneeeeeeeeeee cece nent seen nae eeeeaaeeeeeeaaeeeeeeaaeeeeeaaeeeseeaaeeeeees 3 19 Safety Agency Approval ratresi ca 3 20 Defin ONS oi a aia aid 3 21 ENCIOSUTES iio da A AA A de ee AS 3 23 Power SWite M acciona rt a da ri 3 24 Cable Connections umi idas 3 24 Operation and MaintenancCe ooccccoonnnccccnnocnncnnnonnnonnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnrnnnnnnarnnnnanannnnns 3 25 Chapter 4 Programmable Keyboard Interface Module oommcccoonnncccccnnnccncnannccnnnnnncnnnnnnnnenenannnnnnans 4 1 Loading the PRIM Utility coi pdas 4 1 Using the PKIM UtilitY comodato dilatada a aaa pede aaaea aaa Aahidi 4 1 PRIM Startup coito iia nota tender teed autiaateteys wethoomeiten daa coito 4 2 PRIM Utility Batch ModE ccoo O alee dade ead 4 2 Malt MON AIEEE a Aachen ee ae E Ae eee Nees cate ae chs A touts St eh 4 3 NO 4 3 o o ena T 4 3 Macros Menta A a dd 4 4 Upload Menu opi alli canteens tenia dica
12. FDD 2 by pulling out the tab on the board and sliding the end of the connector into it Once the connector is inserted push the top of the tab back in toward the board Attach the COM1 and COM2 connectors internally Attach any serial devices to COM1 or COM2 on the VO panel Attach a printer to LPT1 optional Plug an external speaker into SPKR optional Plug the flat panel cable into FPNL Reconnect the slide out computer module to the front panel refer to the Removing the Slide Out Module section earlier in this chapter Connect the power sources The CPU is now ready for operation Chapter 3 Installation Available Power The power supply provides 80 watts of output throughout the 9485 9487 s temperature range The expansion power is limited as shown in Table Chapter 3 2 Table Chapter 3 2 9485 9487 Available Current Available Current Available Current 486 or Am5x36 Processors Pentium Processors Voltage Amps Watts Amps Watts Hazardous Locations Installations Xycom offers an optional version of the 9485 9487 with the intention of meeting the re quirements of Class I Division 2 Hazardous Locations applications Class II Division 2 requirements can also be met when the system is installed in an approved Type 4 enclo sure Division 2 locations are those locations that are normally non hazardous but could become hazardous due to accidents which may expose the area to flammable vapors gases or c
13. drives The drawer is easily removed by detaching six ACCESS fasteners Standard Features The 9485 9487 offers the following standard features e High performance single board 486 Am5x86 and Pentium processors e 5 62 inch mounting depth e Four slot full length passive ISA backplane e Flat panel display 640x480 10 4 inch 256 color STN LCD dual scan 9485 10 4 inch 256 color CCFT TFT LCD 9487 e 32 data entry and 20 function keys e 3 5 inch 1 44 Mbyte floppy drive e MS DOS e Slide out computer module for access to disk backplane and power supply e 110 watt power supply e IBM PC AT compatibility 1 1 9485 9487 Manual e Front or rear access floppy disk e External printer port e External COM1 and COM2 ports RS 232 e Front panel sealed to meet NEMA 4 4X 12 specifications when panel mounted Optional Features The following optional items are also available with the 9485 9487 e A variety of high capacity IDE hard drives and Solid State Flash drives e RADAR card with isolated RS 232C RS 485 serial ports e External full stroke keyboard e Durapoint sealed front panel mouse e 24 volt DC power supply e Two button serial mouse e Various sealed rack or panel mount keyboards see Chapter 3 Table 3 1 e Preloaded Windows 95 or Windows NT operating systems Unpacking the System When you remove the 9485 9487 from its box verify that you have the parts listed below Save the box and inner wrapping in cas
14. hazard batteries must only be changed in an area known to be non hazardous Warning Explosion Hazard When in hazardous locations turn off power before replacing or wiring modules Advertissment Risque D Explosion Dans les situations hasardees couper la courant avant de remplacer ou de cabler les modules Warning To maintain a safe condition an external keyboard must not be used when the unit is operating in a hazardous environment Definitions The following Class and Division explanations are derived from Article 500 Sections 5 and 6 of the United States National Fire Protection Agency National Electric Code NFPA 70 1990 They are not complete and are included here to provide a general de scription for those not familiar with generic hazardous locations requirements Persons responsible for the installation of this equipment in hazardous locations are re sponsible for ensuring that all relevant codes and regulations related to location rating enclosure and wiring are met Class Locations Class I locations are those in which flammable gases or vapors are or may be present in the air in quantities sufficient to produce explosive or ignitable mixtures Class II Locations Class II locations are those that are or may become hazardous because of the presence of combustible dust 9485 9487 Manual 3 22 Division 1 Locations A Division 1 location is one in which flammable or ignitable gases vap
15. is disabled when it is re enabled the system must be pow ered up for a minimum of 30 seconds Failure to follow this procedure may result in premature battery failure Disconnect all power supplies Remove the slide out computer module Verify all jumper settings as noted on the bottom of the front panel Place the CPU card into slot 0 connectors JK7 and JK8 in the backplane Push down on the card evenly until it firmly seats into the card edge connectors gee eae 5 Secure the ORB with one screw at the top Note Not all of the following connections will be in every application The in stallation instructions are geared toward an application using all of the CPU capabilities Ignore those that do not apply Caution Connectors can be connected backwards if you do not use keyed con nectors Ensure that the markings on the ribbon wire mate to pin 1 on both the board and the other component 9485 9487 Manual 3 18 Note Before connecting a ribbon cable to latched connectors make sure the latches are pulled halfway down When the cable connection is made the latches snap up When removing a cable connector move the latches down near the board This ejects the connector so you can remove it easily 8 9 10 11 12 13 14 If an external battery is used connect the lead to BAT IN For information on ena bling or disabling jumpers refer to your CPU manual Attach the floppy drive connector to
16. power required by these systems classifies the power switch as an incendiary device That is the voltage and current across the make break device is capable of creating a spark Hazardous locations regulations require that a power switch rated for ordinary locations may be used if it is located in an area specified as non hazardous However limits in ca ble length between the workstation and the power switch may apply Otherwise the switch must be compliant with Class L Division 1 requirements intrinsically safe These switches are built in a manner that prevents the possibility of a spark when con tacts are made or broken Suitable UL listed and or CSA Certified Class I Division 1 switches must be used in hazardous locations These switches are available from a number of sources It is the re sponsibility of the customer to ensure that the power switch selected for the installation has the correct hazardous locations rating for the location in which it is installed Cable Connections 3 24 Division 2 hazardous locations regulations require that all cable connections be provided with adequate strain relief and positive interlock A cable should never be connected or disconnected while power is applied at either end of the cable Power Cable Connection The power cable supplied with units configured for use in hazardous locations are UL Listed Type SJT 3 conductor 18AWG cord sets The system is supplied with a connec tor clamp that s
17. scan codes are listed in Table Chapter 4 1 Table Chapter 4 1 Special PKIM Scan Codes Code Meaning Chapter 4 Programmable Keyboard Interface Module Table Chapter 4 2 defines the hex scan codes used by the PKIM utility Table Chapter 4 2 Hex Scan Codes Space reso Table shaped 2 china on following page or PESE 5A 59 22 2 58 LOPE aed E pa pee 5 ECU 4 9 9485 9487 Manual Table Chapter 4 2 Hex Scan Codes continued from previous page Piso o enmon 68 IE E TEO ECT TIC E ETT a pa PB m feon feat fe Bwa jo f 2 4 10 Chapter 5 Maintenance The 9485 9487 was designed to withstand the harsh environment of the factory floor Routine maintenance can keep your 9485 9487 in good operating condition Preventive maintenance consists of several basic procedures that will greatly reduce the chance of system malfunction Preventive maintenance should be scheduled along with the regular equipment maintenance to minimize 9485 9487 down time Preventive Maintenance Some preventive measures are listed below Clean or change the fan filter periodically to ensure that the air circulating in the unit is clean Wash the filter with warm water and dish soap and let it air dry Do not scrub the filter and do not re install it into the unit until it is completely dry Base your maintenance schedule on the type of environment the system is in 1 e if th
18. started with the t switch PKIM Utility Batch Mode Versions 2 2 and above of the PKIM utility include a mode for reprogramming keypads from a batch file This feature is useful if you wish to reprogram many units with custom ized keypad macros without having to enter the full PKIM utility for each unit Once the full utility has been used to create and save keypad macros the files containing these macros can be included on a disk with the PKIM utility and then used to reprogram other units from a batch file PKIM filename Runs the PKIM utility batch mode where filename is the file containing the new keypad macros The filename extension must be included For example in a batch file PKIM nudef32 pkm would reprogram the default values for the numeric keypad You may also specify multiple macro filenames in the PKIM line For example PKIM nudef32 pkm 20funcff pkm will reprogram both the numeric and the function key key pads Chapter 4 Programmable Keyboard Interface Module Main Menu The main menu provides six selections Exit Files Macros Upload Download and Utili ties Figure Chapter 4 1 depicts the Main Menu Xycom PKIM Utility MAIN L Arrow R Arrow Enter Figure Chapter 4 1 PKIM Main Menu Each of the Main Menu selections is described in separate sections below Choices from the menu are discussed in the order they appear on the screen Exit Exit closes open files and exits the utility ESC can also be us
19. 9485 9487 PC AT Flat Panel Industrial Computer P N 99330 002E 1997 XYCOM INC Printed in the United States of America Xycom Revision Record Revision Description Manual Released Manual Updated Manual Updated Not Released Manual Updated updated rev level Trademark Information Brand or product names are registered trademarks of their respective owners Copyright Information This document is copyrighted by Xycom Incorporated Xycom and shall not be reproduced or copied without expressed written authorization from Xycom The information contained within this document is subject to change without notice xycom Technical Publications Department 750 North Maple Road Saline MI 48176 1292 313 429 4971 phone 313 429 1010 fax Table of Contents Chapter 1 Introductions cc iii das 1 1 Standard Features ochena Aiei A a E LA a ci 1 1 Optional FSQtUTOS mrar eo i ana to a de tai ada 1 2 Unpacking the System nesrecna ri a id da did are 1 2 QUICK Start Up san eaea a aaae aae aa ea aa a a aaie eap eaaa 1 3 Chapter 2 Testing iii ads 2 1 Checking System SUD a 2 1 Phoenix BIOS aaneen tnne eiaa a E eA EER EE EAE E EE N 2 1 eWt tori eD R PA A A O T E eran bb iaa tak 2 2 Preparing tOr MS Tests ui a ie chains 2 2 PRUNING ihe Tests ai aa aca 2 3 Chapter 3 Installation oooomcccccnnnneccnonnnnncnonnnnnnnnnnnn rre 3 1 System COMPOME MS vessinssceisserscesteatadecehdarecssrad tech seasuuebtata
20. ace the 9000 RAD card into the slots in the backplane Push down on the card evenly until it firmly seats into the card edge connectors 6 Secure the 9000 RAD ORB to the host system by replacing and tightening the screw that was removed in Step 4 7 Reconnect the computer module to the front panel and tighten the fasteners that were removed in Step 2 8 Plug the 9485 9487 into an AC wall outlet and turn on the power Chapter 3 Installation DRAM and Additional DRAM Single Line Memory Modules SIMMs You can order your 9485 9487 CPU factory configured for many DRAM configurations You can reconfigure the DRAM capacity by changing the DRAM SIMMs on your board For more information refer to the CPU manual Installing External Hardware Options This section explains how to install the external hardware options available with the 9485 9487 Extender Cable The extender cable allows the 9485 9487 to operate when the slide out computer module is pulled out from the system enclosure This cable connects between the two P2 and P3 connectors on the front panel and the interconnects on the backplane of the 9485 9487 Caution High voltages are present in the computer module when the extender ca ble is used The extender cable should only be used for development and servicing Do not leave the unit unattended when the extender cable is used 1 Turn off the power 2 Remove the slide out computer module refer to the Remov
21. al panel 5 6 7 8 Detach the CPU module Install the monitor portion of the unit into the cutout Reattach the CPU module Tighten the 14 10 nuts to 27 inch pounds Installing PC AT Boards 3 16 1 AAA DO Check that the memory and I O configuration of the board you want to install does not conflict with the CPU and I O memory maps in your CPU board manual Remove the slide out computer module Remove the ORB screw in the desired track Slide the PC AT board into a corresponding rail Push the board into the backplane connectors Note Do not force the boards or apply uneven pressure Secure the board by installing the screw through the hole in the board s metal ORB and into the top of the track Reconnect the slide out computer module to the front panel refer to the Removing the Slide Out Module section earlier in this chapter Chapter 3 Installation Note On systems with 133 and 200 MHz Pentium processors the CPU may be moved to slot one to obtain a total of three expansion slots If this is done derate the temperature specifications by 5 C Refer to Appendix A for temperature specifications Installing the CPU into a Chassis Following are the steps required to install the CPU into a chassis Warning Disconnect all external power supplies before you open and service any piece of equipment Also always use static protection when handling CPU boards Warning If the battery
22. ance Fault and RA DAR are programmable and can be accessed through Xycom s LED Status register Refer to your Xycom CPU manual for more information on programming status LEDs Chapter 3 Installation Contrast On the 9485 display contrast can be regulated us ing the data entry keypad Use the ALT and key to increase the contrast ALT and the key to de crease the contrast Note The contrast inherent in the 9487 TFT active matrix LCD technology eliminates the need for contrast adjustment Back Panel Figure Chapter 3 2 illustrates the 9485 9487 back panel components PRODUCT REMOVE ACCESS FASTENERS 6 I D LABEL TO DISASSEMBLE SYSTEM 04 Se eigaqa Y amp amp ty REAR FLOPPY EXTERNAL BATTERY HOLDER ACCESS PLATE Figure Chapter 3 2 9485 9487 Back Panel 3 3 9485 9487 Manual ACCESS Fasteners Floppy Disk Access Product ID Label Power Panel There are six fasteners located across the top and bottom of the back panel Each is labeled AC CESS When these fasteners are removed you can remove the slide out computer module The floppy disk drive can be user configured for rear panel access Remove the metal plate to ac cess There is some disassembly and re assembly required to change the floppy drive from front to rear access This label located in the upper left corner of the back panel includes IDE hard drive setup infor mation A se
23. anual After you have finished installing options on your 9485 9487 reconnect it to the front panel according to the instructions below 1 Match the top and bottom guides on the module with the slider indentations on the inside of the front panel shell as illustrated in Figure Chapter 3 5 2 Push forward firmly until the top and bottom of the module are flush with the top and bottom of the front panel shell 3 Reinsert the six ACCESS fasteners removed earlier see Figure Chapter 3 2 Installing Internal Hardware Options Caution Turn off the unit before installing internal hardware To install internal hardware options you first need to remove the slide out module 9000 RAD Card Before installing the 9000 RAD card Solid State Disk board into the 9485 9487 jump ers and switches must be set appropriately for your particular configuration See your 9000 RAD manual for more information After the 9000 RAD is properly configured it can be installed into the 9485 9487 card cage as follows 1 Unplug the 9485 9487 from the AC wall outlet 2 Remove the 9485 9487 slide out computer module refer to the Removing the Slide Out Module section earlier in this chapter Set the six ACCESS fasteners aside for later use 3 Verify jumper and switch settings Refer to the 9000 RAD manual for the correct settings 4 If present remove the blank ORB from the slot that the 9000 RAD card will occupy Save the screw 5 Pl
24. ated on the CPU board Refer to the CPU manual for more information Table Appendix C 4 Parallel Port Pinouts Pin Signal 2 Po Eien a AUTOFEED PERROR INIT SELIN GND GND GND je PDe 21 GND GND GND GND GND 143 SELECT Speaker Jack Connector The speaker jack is a subminiature phone jack located on the CPU board Refer to the CPU manual for more information Table Appendix C 5 Speaker Jack Pinouts SOURCES CURRENT SLEEVE C 3 Index Numeric 9000 RAD card installation 3 8 A ACCESS fasteners 3 4 access floppy disk 3 4 approvals safety agency 3 20 BIOS Phoenix 2 1 Quadtel 2 2 setup information 2 3 block diagram B 1 C cable connections hazardous locations installations 3 24 communication 3 25 power 3 24 Class I locations 3 21 Class II locations 3 21 COM port C 2 COM2 port C 2 unavailable 3 6 communication cable interface 3 25 connectors COM1 3 6 C 2 COM2 3 6 C 2 keyboard 3 2 3 5 C 1 parallel port LPT1 C 3 printer 3 6 serial loopback 2 3 speaker 3 6 speaker jack C 3 VGA C 2 video 3 6 contrast display 3 3 CPU installation into a chassis 3 17 current available 3 19 D data entry keypad 3 2 diagnostics 2 1 Index 1 9485 9487 Manual dimensions logo B 2 system cutout B 2 display 3 2 display contrast adjusting 3 3 Division 1 locations 3 22 Division 2 locations 3 22 DRAM installation 3
25. ations If your system has the Windows 95 or Windows NT operating system the video drivers are installed in the operating system Note Read the install txt file in the OS2 subdirectory to create an OS2 driver disk Installing the Sealed Durapoint Mouse Drivers Xycom offers an optional sealed Durapoint mouse installed in the front panel floppy door If you have purchased this option a driver disk will be included with your system This disk contains drivers that optimize the functionality of the Durapoint mouse for the MS DOS Windows 3 x and Windows 95 operating systems Note If you have ordered the touch screen option along with the Durapoint sealed mouse option you will need to use a standard Logitech mouse driver The custom Durapoint drivers do not operate properly when a touch screen is installed 9485 9487 Manual Using a Touch Screen 3 12 The Xycom touch screen is based on resistive membrane technology and consists of two thin sheets of polyester with transparent conductive coatings on the facing sides Finger or stylus pressure causes the outer sheet to make electrical contact with the inner sheet Xycom s touch screen complies with environmental specifications and maintains a NEMA 4 seal when panel mounted It remains operational even after two million touches The touch screen interface module circuit impresses a voltage across the conductive coatings and when pressed converts from analog to x and y
26. cessenstaaperadteee seas saeebiadtacbetetaugerndteed denn nceeth 3 1 FONT Paola income 3 1 Back Pa ii A A A AA O ta te 3 3 Power Panel ic ooo EER 3 4 VO PANEL unos iii 3 5 Preparing the SM iio 3 6 Removing Reconnecting the Slide out Computer MOdule 0 cceeeeeeeneeeeeeeaeeeeeeeaaeeeeeeaaeeeeeeaaeeeeees 3 6 Removing the Slide Out Module asainne a aan Ea A AETA ERAN SEEEN AAST ETERRA 3 7 Reconnecting the Slide out Module sspears niini enaa aA A EEA NAE RA ENAERE AAAA 3 7 Installing Internal Hardware Options arseenin e e i A EN EA aE EEDA Ra 3 8 9000 RAD Cdi EE AA TE A E E E AEN 3 8 DRAM and Additional DRAM Single Line Memory Modules SIMMS oooonccccnoncccccnnncccncnnnnccncnnnnccnns 3 9 Installing External Hardware OPtIONS oooooccccnonncccononoccnononnccnnnnnnccnonnnnccnnnnnnccnnnnnnccnnnnnncrcnnnnncrnnnnnncinns 3 9 Extender Cable cti e iio ola 3 9 KeybOards ii da 3 9 sonal MOUS coito 3 10 Installing Operating SYStOMS siared aaea AEA AA E AAAA TAER EAA AAT 3 10 Installing the 82014 Font TSR eerie a bras 3 10 Installing videt Divers rascar E a EAEE a A A E E AES 3 11 Installing the Sealed Durapoint Mouse DriVerS ocooconnccccncncccnnnonnccnnnnnnccnnnnnncrnnnnnncrnnnnnncrnnnnnncrnnnnnnens 3 11 Using a TOUCH A NS 3 12 Installing the System into a Paneler e A A A RA E SEATS 3 13 Mounting Considerations cio aE AN ARE EENE RE a E ATE eee NAA 3 13 E POWER E E A E E A E EE E E E E E A 3 14 Excessive Heal rarena sariin aee aE
27. com PKIM Utility and the current menu title are shown at the bottom of the screen see Figure Chapter 4 1 A full stroke keyboard is needed to enter keystrokes while recording a new key macro editing an existing macro and entering utility commands All keys on the keypads are re definable While the utility is running the keypads are disabled Dialog boxes appear for user prompts and to display error and user advice messages Two keys can be used to exit from the menus e ESC moves to the previous menu or out of the utility from the Main Menu e Fl returns to the current menu headings in some of the menus where Exit can be chosen to exit this menu The keys specific to each menu are shown at the bottom of each screen 4 1 9485 9487 Manual PKIM Startup This section describes the startup options for the PKIM utility PKIM l t Runs the full PKIM utility Where Ir Reduced functionality Some keyboard controllers will not allow the PKIM utility to have control In this case keycodes uploaded from the EEPROM cannot be translated correctly Starting the PKIM utility with the r switch removes the Upload option from the Main Menu In this mode editing must start with macros read in from a file since they cannot be read from EEPROM It e Translate Some systems initialize the keyboard to run in XT mode In this case the scan codes read in from the keyboard when in Teach mode will not be correct unless the PKIM utility is
28. ctor strain relief to maintain a reliable degree of strain relief The D sub connectors must always be secured to the 9485 9487 workstation mating connectors via the two screws located on both sides Warning The communication cables should never be connected or disconnected while power is applied at either end of the cable This may result in an incendiary spark Furthermore permanent damage to the workstation communication components may occur Operation and Maintenance 9485 9487 systems have been investigated for compliance with relevant spark ignition tests by UL However please note that the workstation front panel membrane keyboard keys and keyboard connector are the only make break components intended to be exer cised by the operator in the course of normal operation Warning To maintain a safe condition an external keyboard must not be used when the unit is operating in a hazardous environment With respect to hazardous locations installations the following rules must always be ob served 1 The workstations must always be installed within an enclosure suitable for the spe cific application General purpose enclosures may be acceptable for Class I applica tions but are never acceptable for Class II applications Type 4 IP 65 enclosures are recommended even when not required by regulations 2 Ifpresent enclosure doors or openings should remain closed at all times to avoid the accumulation of foreign matter ins
29. d COM2 connec tors Disconnect the serial cable from COM1 Connect the jumper to the COM1 connector Connect the COM2 serial cable to the COM2 port Reconfigure the touch screen driver for COM 1 Refer to the Elographics manuals for details The COM2 port is now enabled and the COM port is disabled Sy SOS a Removing Reconnecting the Slide out Computer Module The slide out computer module allows access to the CPU boards and disk drives The slide out module is shown in Figure Chapter 3 5 Chapter 3 Installation Figure Chapter 3 5 Slide out Computer Module Removing the Slide Out Module 1 Remove the six ACCESS fasteners shown in Figure Chapter 3 2 that attach the slide out computer module to the 9485 9487 back panel A 14 inch nut driver is needed to remove the 8 32 size fasteners 2 If the unit is not panel mounted place it face down Hold the front part down lo cated behind keypad while pulling off the back panel to break the interconnect con nection 3 Grasp the handles that protrude from the back panel on the left and right sides above the I O inserts 4 Pull straight back The module should slide out easily Reconnecting the Slide out Module Note If you are replacing the current module with a different module refer to Table 5 1 for the correct switch settings If the switch settings are incor rect the Fault light blinks and the display will not light up 3 7 9485 9487 M
30. digital coordinate positions and passes the x and y codes to the Elographics driver installed The touch screen moni tor mouse driver emulates a Microsoft mouse Note Refer to the Elographics manuals for complete installation details Specify Elodev 2210 2 9600 when installing the default touch screen driver Note When a touch screen is factory installed the COM2 port is disabled There are some special considerations when you have a mouse and a touch screen con nected at the same time When a mouse is set to relative mode a standard mouse driver has two modes absolute and relative the monitor mouse driver will not be aware of movement because it can only send information to the mouse driver it cannot receive in formation from the driver You may correct this problem by disconnecting the mouse Elographics provides a pro gram called patchmse which patches the mouse driver to operate without a mouse con nected If you do not have the option of disconnecting your mouse follow the steps below to get the touch screen and the mouse cursor into synchronization 1 Touch the touch screen in the center and while still pressing slide your finger all the way to the right side center then to the top center then to the left center and fi nally to the bottom center 2 The cursor should be directly under your finger If not try the steps again moving more slowly across the screen or recalibrate the touch screen using the exec
31. e cursor will appear on the Edit line 4 Place the cursor on the last character to copy and press ENTER The copied item does not appear on the screen until you select Paste Inserts a sequence of scan codes which were saved in memory using Copy into the macro To paste a se quence of scan codes that were previously copied posi tion the cursor where you want the text to appear and then press F1 Select Paste and then press ENTER Displays a table of keys and their scan codes in hex Toggles between displaying the scan codes in hex and decimal formats Toggles the insert key between insert and overtype mode Chapter 4 Programmable Keyboard Interface Module Upload Menu Use the Upload Menu to choose which keypad macro information to load The menu choices are defined below Function Keypad Commands the PKIM to send its entire macro set for the func tion key keypad Numeric Keypad Commands the PKIM to send its entire macro set for the nu meric key keypad Keyboard Commands the PKIM to send its entire macro set for the switch array keyboard The 9485 9487 does not support the ability to reprogram switch array keyboards You may choose to upload a keyboard but the keys will not be defined PKIM version Commands the PKIM to send its firmware revision number Exit Returns to the Main Menu Note Only one macro set may reside in memory at one time Also Upload is not available if the utility is started with the
32. e area is dusty you should schedule maintenance more often than if it is a dry clean area Also check the filter often to determine if it needs to be changed ahead of schedule Remove dust and dirt from PC components If dust builds up on heat sinks and cir cuitry an obstruction of heat dissipation could cause the unit to malfunction If dust reaches the electronic boards a short circuit could occur Check the connections to I O modules especially in environments where shock could loosen the connections Check to see that all plugs sockets terminal strips and module connections are solid Do not place unnecessary articles such as drawings or manuals on the unit They could obstruct air flow and create hot spots which cause the system to malfunction Do not place noise generating equipment near the 9485 9487 Stock spare parts to minimize down time resulting from part failure The spare parts stocked should be 10 percent of the number of each unit used Main CPU cards should have one spare each Each power supply should have a backup In certain ap plications where immediate operation of a failed system is required an entire spare computer module may need to be stocked See the Spare Parts List later in this chapter Make sure the module is the correct type when replacing If the new module solves the problem but the failure reoccurs check for inductive loads that may be generat ing voltage and current spikes and may require ex
33. e you need to reship the unit e 9485 9487 unit e Documentation kit which includes Power cable PKIM utility disk Diagnostic software disk 20 hex nuts 6 spares 9485 9487 user manual CPU manual VGA utility disk e Binder e Business reply card If you ordered the system with a touch screen installed you will also receive a touch screen driver disk and a manual 1 2 Chapter 1 Introduction Quick Start up Warning Turn off the power to the unit and unplug the power cord before making any adjustments to the inside or outside of the computer Perform the following steps to prepare the system for use 1 Attach optional keyboards mouse Connect an external keyboard to the keyboard connector behind the access door on the front panel or to the connector on the power panel A serial mouse can be connected to either COM1 or COM2 If a touch screen is in stalled one of the COM ports will no longer be available default is COM2 When a mouse or touch screen is used the COM LED on the data entry keypad lights up Re fer to the Touch Screen manual to use the touch screen and mouse simultaneously Attach other optional equipment following the instructions in Chapter 3 Attach the power cord from the power receptacle to a properly grounded 90 250 VAC 50 60 Hz outlet Turn on the power to the unit The system will boot up at the C prompt Adjust the contrast on the 9485 using the data entry keypad ALT and to incr
34. ease ALT and to decrease if necessary Install application software via drive A located behind the access door on the front panel 1 3 9485 9487 Manual Chapter 2 Testing Diagnostic tests are provided to verify the operation of the 9485 9487 system hardware functions under MS DOS Note Diagnostic disks are not included if your system ships with Windows 95 or Windows NT preloaded These operating systems have built in diag nostics that are invoked when the operating system boots up If any of these tests fail either you do not have the correct default setting or there is a failure Check the default settings and run the tests again If there is another failure contact Xycom s Product Repair amp Customization Department PR amp C Note Unexpected failures may occur if Xycom diagnostics are run with device drivers or memory resident programs installed on the system Remove these before running any diagnostic tests Checking System Setup You want to ensure that the Setup Menu is configured properly factory set configura tion The way you access the Setup Menu depends on the CPU board installed in your system Phoenix BIOS If the CPU board has a Phoenix BIOS press F2 to enter the Setup Menu and then press F2 to display the Main Menu Make the necessary changes by following the on screen di rections General instructions for navigating through the Setup screens are described be low e
35. ece cece cece eter ee ee eee eeeeee eres A E a i C 2 VGA Connector VGA ci iO alt adage anes talent C 2 Paralel Pont Connector PTI a oia C 3 Speaker Jack Connector orere ninie aa EE EAE EAA EA E e EAA AEAEE EAEE AAAS C 3 Chapter 1 Introduction The 9485 9487 PC AT Flat panel Industrial Computer also known as the Portrait PC combines a PC AT computer with a flat panel display to offer a powerful compact pack age for the factory floor and other harsh environments The 9485 9487 features an open architecture to meet a wide variety of applications where both a powerful PC and a dura ble industrial enclosure are required The system integrates a computer card cage mass storage display keypads and power supply in a truly industrial form factor The 9485 9487 system includes a four slot full length passive ISA backplane a VGA flat panel display hard and floppy disk drive facilities and data entry function keypads The front panel is sealed to NEMA 4 4X 12 standards and the flat panel display is pro tected by an impact resistant shield The open architecture design accepts IBM PC AT compatible cards and keyboards The processor board combines the functions of a complete IBM PC AT compatible com puter on a single industrially hardened circuit board Refer to the Xycom CPU manual for more information on processor and hardware features The system s modular design allows easy access to boards switches power supply and disk
36. ecurely fastens the female connector to the unit Warning Explosion Hazard Failure to securely fasten this connector clamp voids the UL listing for use in hazardous locations Plug the female plug of the cable into the AC power receptacle on the system s left side Using the offset screwdriver supplied tighten the clamp securely around the plug The other end of the cable requires field termination to the incoming AC power line The cord may be shortened for optimal length Strip 3 0 inches 76 mm of outer jacket insu lation from the three conductors The three conductors L1 Hot White L2 Blue Neutral and PE Protective Earth Ground Green Y ellow should be stripped to expose 0 25 inches 6 mm of wire A small amount of solder should be applied to these ends to prevent loose strands of wire from being bent back and accidentally shorting to adjacent leads These three leads should be securely fastened to their corresponding in coming lines Chapter 3 Installation Communication Cable Interface All communication cables should include a chassis ground shield This shield should in clude both copper braid and aluminum foil The D sub style connector housing should be a metal conductive type e g molded zinc and the ground shield braid should be well terminated directly to the connector housing Do not use a shield drain wire The outer diameter of the cable must be suited to the inner diameter of the cable con ne
37. ed for this purpose and for exiting the other menus Files Menu Files containing keypad macro sets a macro for each key may be saved on disk and loaded into memory to view edit or download to the PKIM Some of these files may be included in the utility package for use in reconfiguring the keypads for different software packages and as templates for defining completely new keypad macro sets When you choose Files a drop down menu displays the following choices Open Opens a file that contains a macro set for one of the keypads and loads the contents into memory Any macro set previously in memory is overwritten Once loaded the macro set is available to edit view teach and or download to the PKIM Close Clears the macros from memory and closes the file from which they came Save Copies the set of macros from memory back into their original file The origi nal file contents are overwritten 9485 9487 Manual Save As Delete Exit Macros Menu 4 4 Creates a new file under the specified name and copies the set of macros from memory into it For example to define different sets of codes save each set under a different name and download the one you wish to use Deletes a file Returns to the Main Menu When Macros is selected a menu bar displays four choices Exit View Teach and Edit Note You must have a macro file in memory before the Macros Menu is avail able To load a macro file Open or Upload a file
38. g system or re install a current operating system re fer to the operating system manual for instructions Note The Windows NT operating system only ships on CD ROM it does not ship on floppy disk Therefore if Windows NT was preloaded on your system you may have to purchase an external parallel port CD ROM drive if you need to reinstall the operating system Installing the 8X14 Font TSR If an application does not display 8x14 characters correctly you must install the TSR font file found on the disk included with the documentation kit or on C VGA CIRRUS To install this file add the following line to your AUTOEXEC BAT file TSRFONT COM Chapter 3 Installation Once you ve added this line you must reboot the system For more information on edit ing the AUTOEXEC BAT file refer to the MS DOS manuals Note These instructions apply only to MS DOS installations If your system has the Windows 95 or Windows NT operating system the 8x14 font TSR is installed in the operating system Installing Video Drivers Video drivers are found on the disk included with the documentation kit refer to the README file on this disk for information on unzipping the video drivers or on C VGA CIRRUS WIN3 1 For systems with AT5 boards the video drivers are found in the following directories C VGA C amp T548 WIN or using either of the following extensions WINNT OS2 Note These instructions apply only to MS DOS install
39. ide the workstation 3 The unit should never be subjected to any installation or service procedures unless power is removed and the area is non hazardous This includes the installation or removal of power cables communication cables or removal of the rear cover of the unit 4 Installation and service should only be performed by technically qualified service personnel These workstations are designed to require no service in the course of normal operation by an operator Chapter 4 Programmable Keyboard Interface Module A programmable keyboard interface module PKIM circuit is integrated into the front panel of the 9485 9487 This lets users redefine all keypad keys with new scan codes us ing PKIM utility software An external full stroke PC AT keyboard is used to access the PKIM utility This key board is not redefinable Note While the PKIM utility is running the keypad switch arrays are disabled Loading the PKIM Utility The PKIM utility can be run from the disk or copied onto your hard drive To run the util ity from the disk change the directory to the appropriate drive and type PKIM To load the PKIM utility onto your hard drive create a subdirectory for the files and copy all the files on the disk into that subdirectory Enter the subdirectory and type PKIM Using the PKIM Utility The PKIM utility uses a menu bar and pull down menu system All menu bars are dis played across the top of the screen Xy
40. ing the Slide Out Module section earlier in this chapter 3 Connect the male end of the extender cable to the interconnects in the slide out com puter module 4 Connect the female end of the extender cable to the P2 and P3 connectors inside the 9485 9487 front panel located on the PSIC board refer to the system block diagram in Appendix B 5 Turn on the power The computer module cannot be re installed into the computer system with the extender cable connected Before re installing the computer module turn off the power and dis connect the cable Keyboards Four keyboards are available for the 9485 9487 the 8000 KB5 8000 KB6 8000 KB7 and 8000 KB8 Table Chapter 3 1 lists the features of each keyboard 3 9 9485 9487 Manual Table Chapter 3 1 Available Keyboards Keyboard Features PC AT interface keys 8000 KB7 A stand alone 104 key QWERTY NEMA 4 keyboard 8000 KB8 A stand alone numeric NEMA 4 keyboard with 42 function keys The keyboards are installed in the same manner Mount them according to the cutout in Appendix B Once the keyboard is mounted connect the cable to the keyboard port Serial Mouse To install Xycom s 4100 MS1 two button serial mouse attach the connector on the mouse cable to COM1 or COM2 on the side of the back panel Note When a touch screen is factory installed the COM2 port is disabled Installing Operating Systems If you want to install a new operatin
41. ixtures Dust accumulations are normally insufficient to in terfere with normal operation of electrical equipment or other apparatus Combusti ble dust may be in suspension in the air as a result of the following infrequent mal functioning of handling or processing equipment combustible dust accumulations on or in the vicinity of electrical equipment may be ignitable by abnormal operation or failure of electrical equipment Groups All electrical equipment approved for use in hazardous locations must include a group rating Various flammable and combustible substances are divided into these groups as a Chapter 3 Installation function of their individual maximum experimental safe gap MESG explosion pres sure and ignition temperature Component temperatures and the potential for spark based upon voltage current and circuit characteristics within electrical equipment determines the equipment group rating A device approved for installation within Class I Group A locations may also be used in Groups B C or D Note Approved Class I equipment may not be suitable for Class II installa tions Class I includes Groups A B C and D Class II includes Groups F and G Enclosures 9485 9487 systems are designed for installation within a clean and dry enclosure for both ordinary and hazardous locations The front panel meets the requirements of UL and CSA Type 4 4X and 12 enclosures The enclosure used for Class I hazardo
42. lect deselect or use the arrow keys to move then use the SPACE key to select deselect a test or function Figure Chapter 2 2 Main Menu Note Please read the DIAG TXT and CMOS TXT files on the diagnostics disk for detailed information Refer to the CMOS TXT file for BIOS setup information 2 3 9485 9487 Manual 2 4 Note If you use the Solid State Flash drive option avoid repeated running of any hard disk diagnostic utility The Flash drive has a limited number of writes to each logical sector Repeated writes from a diagnostic utility will prematurely shorten the life of the drive Chapter 3 Installation This chapter discusses how to install 9485 9487 options System Components This section describes the components on the 9485 9487 front back power and I O panels Front Panel The 9485 9487 comes equipped with a NEMA 4 4X 12 sealed front panel The panel protects the system s interior when the system is properly panel mounted See panel mounting instructions later in this chapter Figure Chapter 3 1 illustrates the front panel features of the 9485 9487 DATA ENTRY KEYPAD SYSTEM STATUS kass PROTECTIVE SHIELD FEDS AND DISPLAY FLOPPY DISK FUNCTION KEYS KEYBOARD PORT F1 F20 a ACCESS DOOR LATCH 777 Figure Chapter 3 1 9485 9487 Front Panel 3 1 9485 9487 Manual 3 2 Display Function Keys Data Entry Keypad
43. macro in either hex or decimal format and is the line in which the actual editing takes place The bottom line the ASCII line dis plays the macro in ASCII format and is not user configurable This line helps keep track of which part of the macro you are editing and will be updated by the utility as editing takes place For example edit line gt 12 75 FO 75 FO 12 1C FO 1C 12 22 FO 22 FO 12 0 ASCII line gt sh 8 bk 8 bk sh a bk a sh X bk X bk sh EOM The insert delete and cursor control keys are active for editing 9485 9487 Manual When a key is selected the menu bar displays the following choices Exit Cut Copy Paste Codes Hex Decimal and I O Insert Overtype The macro for the chosen key is also displayed Exit Cut Copy Paste Codes Hex Decimal roO Returns to the Edit Menu Deletes a sequence of scan codes from the macro To select a section to cut 1 Place the cursor on the first character to cut 2 Press F1 and select Cut 3 Press ENTER Cut should still be highlighted but the cursor will appear on the Edit line Place the cursor on the last character to cut and press ENTER The last character of every macro is the end of the macro EOM and cannot be deleted Copies a sequence of scan codes from the macro into memory To select the section to copy 1 Place the cursor on the first character to copy 2 Press F1 and select Copy 3 Press ENTER Copy should still be highlighted but th
44. ng changes that enhance operating specifications Products returned to Xycom will be tested with standard Xycom test di agnostics Follow the steps below to prepare the unit for shipment 1 DARA Obtain an RMA number for your unit by calling the nearest Xycom repair center Have the following information available e Company name and shipping and billing address e Type of service desired product repair or product exchange e Product model number part number quantity serial number s and warranty status e Failure mode and failure systems e Purchase order number or repair order number Make sure the front panel assembly is properly attached to the unit and the slide out computer module is secured by all six ACCESS fasteners To speed processing attach failure information to the unit Place the unit securely in a heavy duty box Mark the RMA number on your purchase order and on the outside of the box Send the unit to the nearest Xycom repair center Appendix A Technical Specifications Table Appendix A 1 Hardware Specifications Characteristic Specification Mechanical Height 12 2 310 mm Width 19 483 mm Depth 5 62 143 mm Weight 27 lbs 12 2 kg Electrical 90 250 VAC 20 25 VDC 45 51 VDC 2 1 A maximum 10 A maximum 5 A maximum 47 63 Hz Available Power 486 or Am5x86 Processors Pentium Processors 5 VDC O 3 8A 5 VDC O 2 6 A 12 VDC O 3 2 A 12 VDC O 3 2A 5 VDC O 45 A 5 VDC 45 A 12 VDC 45 A
45. odes 4 8 startup 4 2 Upload Menu 4 7 using 4 1 Utilities Menu 4 7 R reconnecting slide out computer module 3 7 removing slide out computer module 3 7 repair 5 5 replacment fan filter 5 3 fuse 5 2 slide out computer module 5 2 S safety agency approvals 3 20 serial loopback connectors 2 3 serial port connectors C 2 serial ports 3 6 setup information IDE hard drive 3 4 SIMMs installation 3 9 slide out computer module reconnecting 3 7 removing 3 7 replacing 5 2 spare parts 5 4 speaker jack connector C 3 speaker port 3 6 specifications environmental A 2 hardware A 1 system components back panel ACCESS fasteners 3 4 floppy disk access 3 4 product ID label 3 4 back panel 3 3 front panel 3 1 contrast 3 3 data entry keypad 3 2 display 3 2 floppy disk drive 3 2 function keys 3 2 keyboard 3 2 VO COMI 3 6 COM2 3 6 printer port 3 6 speaker port 3 6 video port 3 6 T O panel 3 5 power panel 3 4 fan filter 3 5 keyboard port 3 5 on off switch 3 5 power receptacle 3 5 system cutout dimensions B 2 system power 3 14 system preparation 3 6 system setup checking 2 1 system status LEDs 3 2 T testing 2 1 preparing for 2 2 running 2 3 touch screen using 3 12 TSR 8x14 font 3 10 U unpacking the system 1 2 V VGA connector C 2 video drivers installation 3 11 video port 3 6 Index 3
46. ombustible dusts These systems have been UL and CUL listed as non incendiary devices They are not in trinsically safe and should never be operated within a Division 1 normally hazardous location when installed as described here Nor should any peripheral interface device at tached to these systems be located within Division 1 locations unless approved and or certified diode barriers are placed in series with each individual signal and DC power line Any such installations are beyond the bounds of Xycom design intent Xycom ac cepts no responsibility for installations of this equipment or any devices attached to this equipment in Division 1 locations Note When adding cards it is the customer s responsibility to ensure they meet operating conditions for Class I Division 2 hazardous locations It is the responsibility of the customer to ensure that the product is properly rated for the location If the intended location does not presently have a Class Division and Group rating then users should consult the authorities having jurisdiction to determine what the correct rating for that hazardous location should be 3 19 9485 9487 Manual In accordance with federal state provincial and local regulations all hazardous loca tions installations should be inspected by the authority having jurisdiction prior to use These systems are to be installed serviced and inspected only by technically qualified personnel Safety Agency A
47. ors or combusti ble dusts and particles can exist due to the following e Normal operating conditions e Because of repair maintenance conditions leakage or where mechanical failure or abnormal operation of machinery or equipment might release or cause explosive or ignitable mixtures to be released or produced e Combustible dusts of an electrically conductive nature may be present in hazardous quantities Note 9485 9487 systems are not suitable for installation within Division 1 lo cations Note Electrical equipment cannot be installed in Division 1 locations unless it is intrinsically safe installed inside of approved explosion proof enclo sures or inside of approved purged and pressurized enclosures Division 2 Locations Division 2 locations are listed below e Class I volatile flammable liquids or flammable gases are handled processed or used but confined within closed containers or closed systems from which they can escape only in cases of accidental rupture or breakdown of such enclosures or sys tems or in case of abnormal operation of equipment e Ignitable concentrations of Class I vapors or gases are normally prevented by posi tive mechanical ventilation but which may become hazardous due to mechanical failure of those ventilation systems e Location is adjacent to a Division 1 location e Class II combustible dust is not normally in the air in quantities sufficient to produce explosive or ignitable m
48. pproval 3 20 9485 9487 systems are UL and CUL listed and have also been investigated for compli ance with the following standards e Underwriters Laboratories Inc UL 1604 Standard for Safety Electrical equipment for use in Class I and Class II Division 2 and Class III hazard ous classified locations e Underwriters Laboratories Inc UL 508 Industrial Control Equipment e Canadian Standard Association Specification C22 2 No 213 M1987 Non incendiary electrical equipment for use in Class I Division 2 hazardous loca tions e Canadian Standards Association Specification C22 2 No 14 Industrial Control Equipment e UL File No E180970 Suitable for use in Class I Division 2 Groups A B C and D and Class II Division 2 Groups F and G hazardous locations or non hazardous locations only operating temperature Code T4 Warning Explosion Hazard Substitution of components may impair suitability for Class I Class II Division 2 Advertissment Risque D Explosion La substitution de composants peut rendre ce materiel inacceptable pour les emplamements de classe I II Division 2 Warning Explosion Hazard Do not disconnect equipment unless power has been switched off or the area is known to be non hazardous Advertissment Risque D Explosion Avant de deconnecter l equipment coupler le courant ou s assurer que l emplacement est designe non dangereux Chapter 3 Installation Warning Explosion
49. r switch A checksum will be calculated during transmission and an error message displays if an er ror occurs Download Menu Caution Any macro set previously programmed is overwritten when you select Download Download sends the set of keypad macros to the PKIM The macro set must reside in memory before you can download it During transmission a checksum is calculated and an error message displays if an error occurs As the macro is sent PKIM programs its EEPROM with the new macros which become the new key definitions for the selected keypad Utilities Menu When you select Utilities a menu bar displays the following menus 9485 9487 Manual Codes 4 8 Func Lock ON Func Lock OFF Clear EEPROM Exit Turns on the function key interlock feature The function key in terlock disables all function keys as long as one function key is pressed only one function key can be activated at one time Turns off the function key interlock feature allowing multiple function key presses Erases the EEPROM memory This clears the set of keypad macros the contrast setting the backlight timeout setting and the function key interlock setting After using this feature turn the unit off and then on This initializes the EEPROM with the de fault settings Returns to the Main Menu Special PKIM codes replace the standard IBM scan codes for 101 key keyboard en hanced keys in macros that use these keys The special
50. re a chassis makes contact with the enclosure In addition to the ground connec tion made through the mounting bolt or stud a one inch metal braid or size 48 AWG wire can be used to connect between each chassis and the enclosure at the mounting bolt or stud e The enclosure should be properly grounded to the ground bus Make sure a good electrical connection is made at the point of contact with the enclosure e For continued safety machine ground should be connected to the enclosure and to earth ground Excessive Heat 9485 9487 systems are designed to withstand temperatures from 0 to 50 C The systems are cooled by convection in which a vertical column of air is drawn in an upward direc tion over the surface of its components To keep the temperature in range the cooling air at the base of the system must not exceed 50 C Proper spacing must also be allocated between internal components installed in the enclosure When the air temperature is higher than 50 C in the enclosure use a fan or air conditioner Chapter 3 Installation Excessive Noise Electrical noise is seldom responsible for damaging components unless extremely high energy or high voltage levels are present However noise can cause temporary malfunc tions due to operating errors which can result in hazardous machine operation in certain applications Noise may be present only at certain times may appear at widely spread intervals or in some cases may exis
51. t a comfortable working level Consider locations of accessories such as AC power outlets and lighting interior lighting and windows for installation and maintenance convenience Install a thermostat controlled heater or air conditioner if condensation is expected Avoid obstructing the air flow to allow for maximum cooling Place any fans or blowers close to the heat generating devices Ifusing a fan make sure that outside air is not brought inside the enclosure unless a fabric or other reli able filter is used This filtration prevents conductive particles or other harmful con taminants from entering the enclosure Do not select a location near equipment that generates excessive electromagnetic in terference EMI or radio frequency interface RFI equipment such as high power welding machines induction heating equipment and large motor starters Place incoming power line devices such as isolation or constant voltage transform ers local power disconnects and surge suppressors away from the 9485 9487 The proper location of incoming line devices keeps power wire runs as short as possible and minimizes electrical noise transmitted to the 9485 9487 9485 9487 Manual e Make sure the location does not exceed the 9485 9487 s shock vibration and tem perature specifications e Avoid overloading the supply circuit e Incorporate a readily accessible disconnect device in the fixed wiring for perma nently connected systems
52. t continuously Noise usually enters through input output and power supply lines and may be coupled into lines electrostatically through the capacitance between these lines and the noise sig nal carrier lines This usually results from the presence of high voltage or long closely spaced conductors When communication lines are closely spaced with lines carrying large currents the coupling of magnetic fields can also occur Use shielded cables to help minimize noise Shielded communication cables should be grounded at the 9485 9487 end only Potential noise generators include relays solenoids motors and motor starters especially when operated by hand contacts like push buttons or selector switches In ac cordance with National Electrical Code specifications 1t is recommended that the high voltage and low voltage cabling be separated and dressed apart In particular the AC ca bles and switch wiring should not be in the same conduit with the PLC communication cables Excessive Line Voltage The power supply section of the 9485 9487 is built to sustain line fluctuations of 90 250 VAC and still allow the system to function within its operating margin As long as the incoming voltage is adequate the power supply provides all the logic voltages necessary to support the processor memory and I O In cases in which the installation is subject to unusual AC line variations a constant voltage transformer can be used to prevent the system from sh
53. t operate the 9485 9487 without a fan filter Dust build up could cause the unit to malfunction Figure Chapter 5 2 Changing the Fan Filter 5 3 9485 9487 Manual Spare Parts List Following is a list of available 9485 9487 replacement parts To order contact the Xy com Customer Service department at 1 800 289 9266 e Front Panel Assembly e STN Display 9485 e TFT Color Display 9487 e Replacement Bulb Assembly e STN 9485 e TFT 9487 Note As flat panel display technology changes rapidly please provide Xycom Customer Service with a model number if you need to purchase a re placement part for a display display bulb or inverter This model number is located inside the unit on the display itself e CPU specify clock speed e AT4 PCI 0 Mbytes e AT5 0 Mbytes e DRAM e Extender cable e Fan filter guard e Drives specify drive size e Floppy drive e Hard drive e Solid State FLASH drive e Keypads e 32 numeric e Function keys e Keypad inserts 9485 9487 e Function keys e ORB blank e PSIC card 9485 9487 5 4 Chapter 5 Maintenance Power cord assembly for units configured for hazardous locations 1 e Class I Divi sion 2 Power supply Touch screen controller Product Repair Program Returning a Unit to Xycom Xycom s Product Repair amp Customization Department PR amp C restores equipment to normal operating condition and implements engineeri
54. ternal suppression Routine Maintenance This section describes routine maintenance you can do on the 9485 9487 9485 9487 Manual Replacing the Fuse Warning Turn off power to the terminal before removing the fuse The 9485 9487 uses a 5 amp 3AG 250 volt fuse The fuse holder is located on the power supply Grasp the fuse or place an object such as a pen or pencil behind it and pull it toward you It should snap out of the holder Replace the fuse by placing it sideways against the holder and pushing it away from you until it snaps into place Figure Chapter 5 1 Fuse Holder Replacing the Slide out Computer Module Refer to Chapter 3 for information on reconnecting the slide out computer module Caution The switch settings on the CPU board must match those listed on the la bel found at the bottom of the front panel Chapter 5 Maintenance Table Chapter 5 1 lists the switch settings for color flat panel displays Table Chapter 5 1 AT Processor Switch Settings Monitor swia swi2 sw swia swis swro swi7 swis If SW1 5 through SW1 8 do not match the label on the front panel the Fault LED will blink to signal a mismatch A blinking Maint LED indicates a communication failure between the CPU and the PKIM Replacing the Fan Filter To change the fan filter remove it as illustrated in Figure Chapter 5 2 Clean the filter and snap the grill back into position Caution Do no
55. the I O panel below the CPU COM2 is not available when the system is shipped with a touch screen installed Refer to Preparing the System later in this chapter for information on reconfiguring the COM ports when a touch screen is factory installed Printer Port The parallel printer port LPT1 is a DB 25 female connector located on the CPU Video Port The video port a 15 pin VGA connector located on the CPU board is shipped disabled To enable it you must change the default switch settings which will disable the flat panel display Refer to the switch settings on the label on the inside bottom of the front panel Speaker Port The speaker port located on the CPU board is a sub miniature phone jack protruding through the ORB For pinout information refer to Appendix C Preparing the System To prepare the system for use attach one end of the power cord to the power receptacle and the other to a properly grounded 90 250 VAC 50 60 Hz outlet see Hazardous Lo cations Installations within this chapter If you have purchased any options install them according to the instructions in the next two sections If a touch screen has been factory installed the COM2 port will be unavailable If you would like to reconfigure the touch screen to use the COM1 port perform the following steps 1 Remove the slide out computer module as described in the following section 2 Disconnect the jumper between the touch screen TCHSCRN an
56. tup information label is also located on the hard disk casing Figure Chapter 3 3 illustrates the components on the left side of the 9485 9487 FAN AND FILTER ON OFF POWER SWITCH PC AT XT KEYBOARD PORT POWER RECEPTACLE Figure Chapter 3 3 9485 9487 Power Components 3 4 Chapter 3 Installation On Off Switch Position this switch to off O until the system is properly configured The switch is removed when configured for hazardous locations Power Receptacle The power receptacle is located below the On Off switch The plug and cord must be securely posi tioned before turning the power on See Hazardous Locations Installations later in this chapter when configuring the system for hazardous locations Keyboard Port Located to the left ofthe On Off switch the key board port allows a PC keyboard to be interfaced with the system Do not use when in the presence of a hazardous environment Fan and Filter The fan and filter are located above the keyboard port The filter cover can be removed for cleaning 1 O Panel Figure Chapter 3 4 illustrates the I O components on the right side of the 9485 9487 FRONT PANEL 486 CPU SPEAKER PORT MOUNTING STUDS PARALLEL PORT ACCESS LATCH VIDEO PORT COM1 COM2 TOUCH SCREEN INTERFACE OPTIONAL Figure Chapter 3 4 9485 9487 I O Components 3 5 9485 9487 Manual COM1 COM2 Ports The serial ports RS 232 are DB 9 connectors lo cated on
57. unit and the male end into a properly grounded outlet Connect the serial loopback connector s and the printer cable to the appropriate connectors and connect a PC AT keyboard to a keyboard connector Figure Chapter 2 1 illustrates the wiring necessary for the loopback connection Chapter 2 Testing 6 7 3 8 4 9 5 Figure Chapter 2 1 Serial Loopback Connections Running the Tests To run the test insert the diagnostics disk into drive A Turn on the computer the diag nostics program will boot up Figure Chapter 2 2 shows the Main Menu as it is dis played on the screen Copyright 1990 1994 Xycom Inc All rights reserved Diagnostic Tests Sequence Selection Menu Rel xx WILL pause on error Auto select tests Save setup to file Quit and exit to DOS 5 SINGLE PASS test mode 6 Deselect all tests 7 8 Extract setup from a file Return to previous screen D RAM Test Video Interface Test Video RAM Test Speaker Port Test Extended RAM Test LPT1 Printer Port Test Real Time Clock Test LPT2 Printer Port Test COM1 Serial Port Test Hard Drive Interface Test COM2 Serial Port Test Hard Drive Interface Test COM3 Serial Port Test Floppy Drive Interface Test COM4 Serial Port Test Floppy Drive Interface Test Math Coprocessor Test Keyboard Keypad Tests G H E aah vu aw video Adjustments Test Test Selected ENTER START TESTING Use the letters to move the cursor and se
58. us locations should have a minimum rating of Type 12 NEMA 12 IP 5X However Type 4 IP 6X enclosures are strongly recommended Warning The floppy disk keyboard port access door must be closed and latched at all times to maintain a proper seal against water and dust Panel flatness and rigidity are important if a proper panel seal is to be maintained If non metal type enclosures such as plastic or fiberglass are used install a rigid metal stiff ener behind the front panel Failure to do so may result in an inadequate panel seal due to flexure of the front panel material between the stud mounts The nuts on the mounting studs must be tightened to 25 inch pounds These systems are UL listed for installation within Class H locations only when installed within UL approved Type 4 enclosures Failure to do so voids that UL listing The requirements for enclosure fittings conduit and wiring vary according to the spe cific rating of the location and the type of flammable or combustible material involved Those requirements are beyond the scope of this document and it is the responsibility of the customer to ensure that their installation is compliant with codes and regulations which apply to their specific location Reference NFPA 70 Article 500 for specific regulations in the United States 9485 9487 Manual Power Switch A 9485 9487 system that will be used in a hazardous location does not have a power switch The amount of input
59. utable file elocalib Also some software packages may cause cursor movement to become erratic ifa loca tion greater than 128 pixels away from the current cursor location is touched This may occur if the variable that is relied on to hold the delta X value is only 8 bits This enables movements of only 128 pixels maximum from the previous position Please contact your software manufacturer if the cursor moves erratically during touch screen use Chapter 3 Installation Installing the System into a Panel The 9485 9487 s rugged design allows it to be installed in most industrial environments The 9485 9487 is generally placed in a NEMA 4 12 enclosure to protect against con taminants such as dust moisture etc Metal enclosures also help minimize the effects of electromagnetic radiation that may be generated by nearby equipment Mounting Considerations Note A full size mounting template can be obtained by contacting Xycom s Application Engineering Department Follow these guidelines when installing your 9485 9487 Select an enclosure and place the unit to allow easy access to the 9485 9487 ports and slide out module Account for the unit s depth when choosing the depth of the enclosure Mount the 9485 9487 in an upright position Note To ensure proper operation of the floppy drives the manufacturer rec ommends that the unit be mounted within 25 degrees of an upright posi tion Place the 9485 9487 a
60. utting down too often However a first step toward the solution of the line variations is to correct any possible feed problem in the distribution system If this correction does not solve the problem a constant voltage transformer must be used The constant voltage transformer stabilizes the input voltage to the 9485 9487 by com pensating for voltage changes at the primary in order to maintain a steady voltage at the secondary When using a constant voltage transformer check that the power rating is sufficient to supply the 9485 9487 Mounting the 9485 9487 Note A full size mounting template can be obtained by contacting Xycom s Application Engineering Department 9485 9487 Manual Once the conditions in the preceding sections have been met follow the instructions be low to mount the 9485 9487 1 Locate a position for your 9485 9487 that meets the specifications required see pre vious sections and Appendix A Add the cutout shown in Appendix B to the enclosure Make sure the area around the cutout is clean and free from metal burrs Implement the proper grounding techniques Establish a ground path from the 9485 9487 chassis to the enclosure chassis Note To make a proper ground scrape paint off the inside of the enclosure panel around the mounting stud holes in at least two places at opposing ends of the unit This insures that a good electrical connection is made between the chassis and the grounded met
61. y 3 2 See programmable keyboard interface module 4 1 L LEDs system status 3 2 line voltage excessive 3 15 locations hazardous Class I 3 21 Class II 3 21 Division 1 3 22 Division 2 3 22 logo dimensions B 2 maintenance 5 1 preventive 5 1 routine 5 1 mounting 3 13 3 15 mouse serial 3 10 MS DOS installation 3 10 N noise excessive 3 15 O On off switch 3 5 operation and maintenance hazardous locations installations 3 25 options external hardware 3 9 internal hardware 3 8 P panel installation 3 13 parallel port LPT1 connector C 3 PC AT boards installation 3 16 pinouts COM C 2 COM2 C 2 keyboard connectors C 1 parallel port C 3 serial loopback 2 3 speaker jack connector C 3 VGA connector C 2 PKIM See programmable keyboard interface module PKIM scan codes programmable keyboard interface module 4 8 ports COM C 2 COM1 COM2 3 6 COM2 C 2 keyboard 3 2 3 5 C 1 parallel LPT1 C 3 printer 3 6 speaker 3 6 speaker jack C 3 VGA C 2 video 3 6 power cable connection 3 24 power panel 3 4 Index 3 9485 9487 Manual power receptacle 3 5 power switch hazardous locations installations 3 24 printer port 3 6 product ID label 3 4 Index 4 Index programmable keyboard interface module 4 1 batch mode 4 2 Download Menu 4 7 Files Menu 4 3 hex scan codes 4 9 loading 4 1 Macros Menu 4 4 Main Menu 4 3 PKIM scan c

9485/9487 - Steven Engineering

Contents

Download Pdf Manuals

Related Search

Related Contents