RoboScan 812 - Music For Dancing
Contents
1. P N 11820002 Set the Address When using the RoboScan 812 with a controller you must set the DIP switch 3 to the start channel also known as the address which is the first channel the controller uses to send instructions to the RoboScan 812 For independent control each fixture must have its own address and control channels Two or more RoboScan 812s may have the same address however they will receive the same instructions and behave identically Installation 7 Martin mode The RoboScan 812 uses 1 channel to communicate with the controller The address may be any channel between 1 and 32 DMX mode The RoboScan 812 may be operated in tracking or vector mode see the DMX protocol for details It uses 5 consecutive DMX channels in tracking mode and 7 consecu tive DMX channels in vector mode The factory default is tracking mode The address may be any channel up to 508 within the controller s range 506 if 7 channels are used Example 4 RoboScans using tracking mode 5 channels may be addressed as follows Of N OO LOOK C0 D O QOD SF LO COI CO OD o Da N 812 No 1 812 No 2 812 No 3 812 No 4 Address 1 Address 6 Address 11 Address 16 Use the following procedure to set a Martin or DMX address 1 Select an available address within the controller s range 2 Look up the DIP switch setting on page 19 You can2. Reassemble the unit before connecting to AC power RoboScan 812 EU Transformer Ballast 50 Hz AC Supply Setting Setting 218 234 V 230 V 230 V 235 240 V 230 V 240 V 241 244 V 250 V 240 V 245 260 V 250 V 250 V Remove the cover above the lamp 6 Remove the cover 8 above the circuit board Move the BROWN transformer wire to the transformer setting shown above Do not move the WHITE and BLUE wires from terminal 1 Remove the end plate 5 to access the ballast RoboScan 812 7 Remove the GRAY wire from the ballast terminal insert a screwdriver in the small hole under the terminal and release the spring with a clockwise turn Open the spring for the correct ballast terminal and insert the GRAY wire The terminals are marked on the side of the ballast Reassemble the unit before connecting to AC power Replacing the Fuse The holder for the main fuse is built in to the mains input socket 4 If the fuse blows repeatedly the fixture requires servicing by a qualified technician Never replace the fuse with one of a different rating 1 Unplug the mains cable from the input socket Pry open the fuse holder and remove the fuse Replace the fuse with one of the same type and rating The fuse rating is listed on serial number label on the end plate Close the fuse holder and replace the mains cable Service and Maintenance 15 appendix a DMX 512 PROTOCOL The RoboScan 812 supports track
3. 812 s XLR connections are configured for Martin protocol controllers such as the 3032 When connecting a RoboScan 812 to any DMX standard device you must swap pins 2 and 3 with a phase reversing cable 1 Connect the controller s data output to the RoboScan 812 s input 2 If using a Martin standard controller use a direct 3 pin to 3 pin cable such as the one provided If using a DMX controller use a phase reversing cable either 3 pin to 3 pin or 5 pin to 3 pin depending on the output of the controller Continue the link connect the output 1 of the fixture closest to the con troller to the input of the next fixture Use a direct cable when connecting same standard fixtures Use a phase reversing cable only when connect ing a DMX standard fixture to a Martin fixture with pin 2 hot Up to 32 fix tures may be connected on a serial link Insert a male 120 XLR termination plug in the output of the last fixture on the link The termination plug is simply a 3 pin male XLR plug with a 120 resistor soldered between pins 2 and 3 The termination plug is required for error free communication 3 pin to 3 pin Phase Reversing Cable Connections Male Female 1 1 2 2 gei 5 pin to 3 pin Phase Reversing Cable 3 pin to 5 pin Phase Reversing Cable P N 11820006 Connections Male Female 1 i 2 2 3S 3 4 5 Connections Male Female ia 2 2 os 4 5 P N 11820003
4. 1899221 2535 285 317 349 3819 413 445 477 509 Oo 1 1 1 1 30 62 94 1269 158 1909222 2544 286 318 350 3829 414 446 478 510 1 1 1 1 1 31 63 95 1279159 1919223 2554 287 3199 351 3839 415 4474479 511 DIP Switch Table 19
5. 6 9 and 10 are set to off DIP SwitchSeting 0 070 070 OF 0 OF 1 191 1491 1914 1 0 070 0F1 191 170 OFO0 O0F1 1491 1 O OFF 0 O0F1 1470 O0F1 170 OF 1 170 071 1 1 0N 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 A 2 B A 6 0 0 00 0 0 32 64 96 f 128 1609192 2244 256 288 320 3525 384 416 448 480 1 0 0 0 0 1 339 6 97 129 161 193 2259 257 289 321 3539 385 4179 449 481 0 1 00 0 2 Al amp 98 150 1624194 226 258 2904 322 3544 386 4184 450 482 1 1 0 0 0 3 3167 997131 1639195 227 259 201 323 3554387 4199 451 483 0 0 1 0 0 4 36 f 68 100 132 1649 196 228 260 202 324 3569 388 420 452 484 1 0 1 0 0 5 379 69 101 133 1659197 229 261 2939 325 3571 389 421 453 485 Oo 1 1 0 0 6 38 70 102 134 166 198 230 262 294 326 3589 390 4221 454 486 1 1 1 0 0 7 399 71 1039 135 1674199 231 263 2951327 3599 391 4239 455 487 0 0 0 1 0 8 40 72 104 136 168 200 232 264 2964 328 3604392 424 456 488 1 0 0 1 0 9 41 f 73 1059 137 1699201 233 265 297 329 3619393 4259457 489 0 1 0 1 0 10 42 74 106 138 1709 202 2344 266 298 330 3629 394 426 458 490 se OO u 8f 7 1079 139 1714203 2354 267 299 331 3639 395 427 459 491 0 0 1 1 0 12 449 76 108 140 1729 204 236 268 300 332 3644 396 428 460 492 10 1 10
6. B 45 J 77 1099 141 173 205 237 269 301333 3654397 420 461 493 Oo 1 1 1 0 14 46 78 1109 142 1749 206 238 270 3024 334 3664398 430 462 494 1 1 1 1 0 15 479 79 1119143 1759207 239 271 303 335 3679 399 431 463 495 0 0 0 0 1 16 48 80 1129 144 1769 208 240 272 3044 336 3684 400 432 464 496 L OR ROR RON a 17 499 81 1139 145 1779209 241 273 305 337 3699 401 4339 465 497 0 1 0 0 1 18 50 82 1149 146 178 210 2421 274 3064 338 370 402 434 466 498 1 1 0 0 1 19 51 8 1159 147 1799 211 243 275 3074339 3719 403 435 467 499 0 0 1 0 1 20 52 J 84 116 148 1809212 244 276 308 340 3729 404 436 468 500 1 0 1 0 1 21 53 85 1179149 1819213 2459 277 309 341 3739 405 437 469 501 Oo 1 1 0 1 22 BAF 86 118 150 1829214 2464 278 310 342 3749 406 438 470 502 ii ti al 23 55 9 87 1199151 1839215 2474279 311 343 3754407 4394 471 503 0 0 0 1 1 24 56 88 1204 152 1844216 248 280 312 344 3764408 4404 472 504 1 0 0 1 1 25 57 89 1219153 1859217 2499 281 313 345 3779 409 441 473 505 OQ Li Ol a a 26 58 90 1221 154 1869218 250 282 314 346 3784 410 442 474 506 1 1 0 1 1 27 599 91 1239155 1879219 251 283 315 347 3794 411 4439475 507 0 O 1 1 1 28 60 92 1249 156 188 220 252 284 31 6 348 3804412 444 476 508 i ab ak al 29 6l 93 1259157
7. also calculate it by subtracting pin values until the total of the values equals the address Start with the highest pin value that can be subtracted and work down until there is no remainder The table below shows the pin values 3 Set the DIP switch 3 by flipping ON the pins found in step 2 pin 1 2 3 4 5 61 71 8 9 10 lt n gt Ww om CO D ojl N BR wl al z E o O mn oO Example Channel 6 Example Channel 82 Pins 2 and 3 ON Pins 2 5 and 7 ON channel 6 channel 82 value of pin 3 4 value of pin 7 64 remainder 2 remainder 18 value of pin 2 2 value of pin 5 16 remainder 0 remainder 2 value of pin 2 2 remainder 0 BERGE GE 45678910 RoboScan 812 section 3 OPERATION Stand Alone Operation The RoboScan 812 may be operated without a controller in stand alone mode In this mode the fixture performs a random sequence that is triggered by the beat of the music or auto matically at a set speed The DIP switch must be set to the desired stand alone mode before applying power Settings for the different modes are shown below 1 With the fixture powered off set the DIP switch 3 for the desired mode Pins not listed must be switched off 2 Apply power to the RoboScan 812 to run the sequence Stand Alone Modes Description Pins Switched ON Random sequence wi
8. mains cable mounting bracket and hardware this user manual Installing a Plug on the Power Cord WARNING For protection from dangerous electric shock the fixture must be grounded earthed The AC supply shall be fitted with a fuse or circuit breaker and ground fault protection The RoboScan 812 is delivered without a plug on the power cord Following the manufac turer s instructions install an approved 3 prong grounding type plug that fits your supply Connect the wires to the pins as listed below The table shows some possible pin identifica tion schemes if the pins are not clearly identified or if you have any doubts about proper installation consult a qualified electrician Wire Pin Marking Screw color brown live SE yellow or brass blue neutral N silver yellow green ground m green Installation 5 Checking voltage and frequency settings The RoboScan 812 voltage setting must be within 5 of the AC mains supply The voltage setting may be adjusted to local conditions The frequency 50 or 60 Hz depending on model however must match your supply Check the settings printed on the label near the mains input See page 13 to change the voltage setting if necessary Releasing the Pan Tilt Lock The pan tilt assembly 9 floats in a special rubber mount to reduce noise when operating the pan and tilt motors In order to protect the pan tilt assembly from damage during ship ment it is secured wi
9. service not described in this manual to a qualified Martin technician This manual covers the RoboScan 812 with software version 2 8 or higher The latest infor mation on the RoboScan 812 is always available from your dealer and the Martin web site at http www martin dk SAFETY PRECAUTIONS The RoboScan 812 is NOT for domestic use For protection against dangerous electric shock always ground earth the fixture electrically use only a source of AC power that complies with local building and elec trical codes and do not expose the fixture to rain or moisture Disconnect the fixture from AC power before removing any cover or part Disconnect the fixture from AC power if the lamp blows Allow the fixture to cool for 10 minutes before installing a new lamp Do not illuminate surfaces within 30 cm 12 inches of the fixture Do not place filters or other objects over the lens or mirror Keep all combustible materials for example fabric wood paper at least 10 cm 4 inches away from the fixture Keep flammable materials well away from the fixture Provide a minimum clearance of 10 cm 4 inches around the fan and air vent Do not operate the fixture if the ambient temperature exceeds 40 C 104 F When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices and secure the fixture with an approved safety cable Block access bel
10. the service consult qualified service personnel for assistance Disconnect the fixture from power before removing any cover Martin 150 W Metal Halide Osram HTI 150 GE CSS 150 Martin P N 97010107 97010108 97010104 Average Life 2000 h 750 h 1000h Color Temp 5000K 6500K 5000K Output 900 Im 1200 Im 900 Im The three lamps shown above may be used in the RoboScan 812 Installing any other lamp may damage the fixture The lamp holder is adjusted at the factory if further alignment is necessary the procedure is described on page 12 1 Remove the 3 thumbscrews 10 securing the lamp socket assembly to the rear of the RoboScan Gently pull out the assembly If changing the lamp remove the old lamp from the socket Holding the new lamp in a clean cloth do not touch the glass carefully insert it firmly and squarely into the lamp socket If your fingers touch the glass clean the bulb with a clean lint free cloth wetted with alcohol Replace the lamp socket assembly and tighten the thumbscrews Service and Maintenance 11 Adjusting the Lamp 12 The RoboScan 812 comes fully adjusted from the factory however readjustment of the lamp may improve performance The lamp is adjusted by turning the 3 screws 11 on the lamp access plate 12 Turning these clockwise pulls the lamp back towards the rear and vice versa Keep adjustments small to avoid pulling the lamp so far off center that it hits the r
11. 2 230 234 90 92 color 1 235 239 92 94 white 240 255 94 100 black 16 RoboScan 812 Gobo 0 15 0 6 closed gt open 15 30 6 12 open gt gobo 1 30 45 12 18 gobo 1 gt gobo 2 45 60 18 24 gobo 2 gt gobo 3 60 75 24 29 gobo 3 gt gobo 4 75 90 29 35 gobo 4 gt gobo 5 90 105 35 41 gobo 5 gt gobo 6 105 120 41 47 gobo 6 gt gobo 7 120 135 47 53 gobo 7 gt gobo 8 135 150 53 59 gobo 8 gt gobo 9 150 165 59 65 gobo 9 gt gobo 10 165 180 65 71 gobo 10 gt gobo 11 180 184 71 72 gobo 11 185 189 73 74 gobo 10 190 194 75 76 gobo 9 195 199 76 78 gobo 8 200 204 78 80 gobo 7 205 209 80 82 gobo 6 210 214 82 84 gobo 5 215 219 84 86 gobo 4 220 224 86 88 gobo 3 225 229 88 90 gobo 2 230 234 90 92 gobo 1 235 239 92 94 open 240 255 94 100 closed Pan 0 0 Max Left 127 50 Neutral 255 100 Max Right Tilt 0 0 Max Up 127 50 Neutral 255 100 Max Down Movement Speed vector mode only 0 0 Tracking mode enabled 1 255 1 100 Speed fast gt slow Color Gobo speed vector mode only 0 0 Tracking mode enabled 1 255 1 100 Speed fast gt slow DMX 512 Protocol 17 appendix b TECHNICAL SPECIFICATIONS RoboScan 812 EU US Dimensions ME CMS a sea aba r a A a EE e 436 mm 17 2 Height incl excl bracket s es 267 mm 165 mm 10 5 6 5 Width incl excl bracket cccccceses
12. RoboScan 812 user manual i 8 T g g ia op E io A i 2 lo i RoR o i F 1 o 8 oth _9 g al oH d 4d I gt 11mm z E h P Oj e Ce 6 g f Cl mmm 1 a5 ls 436 mm 1998 1999 Martin Professional A S Denmark All rights reserved No part of this manual may be reproduced in any form or by any means without permission in writing from Martin Professional A S Denmark Printed in Denmark P N 35000052 Rev C section 1 INTRODUCTION Thank you for selecting the Martin RoboScan 812 It is designed and built to be bright reli able and easy to use With proper setup and maintenance the RoboScan 812 will provide years of trouble free operation Read this manual before operating the RoboScan 812 Safety hazards or damage to the fix ture may occur if it is handled or operated incorrectly For your protection and other s always follow the safety precautions listed below and observe the warnings in this manual and printed on the fixture If you have questions about how to operate and service the fix ture please contact your Martin dealer for assistance before proceeding Refer any
13. The moving mirror allows you to pan the beam 175 and tilt it 83 Movement speed may be adjusted with the controller fade time DMX tracking mode and Martin controllers or on a separate channel DMX vector mode Color Wheel The RoboScan 812 has 13 positions on the color wheel 11 with saturated dichroic colors open white and blackout The wheel can be positioned between 2 colors to split the beam The speed of the color and gobo wheels may be adjusted with the controller fade time DMX tracking mode and Martin controllers or on a separate channel DMX vector mode Selecting color strobe causes the color wheel to change between any 2 adjacent colors or between white and black The strobe speed is variable Gobos The RoboScan 812 has 11 gobos on the gobo wheel plus open and blackout Selecting gobo strobe causes the gobo wheel to change between any 2 adjacent gobos or between full open and black The strobe speed is variable Random Sequence The RoboScan 812 may be set to perform a preprogrammed sequence with automatic or music trigger Focus 10 Focus may be adjusted manually from 1 meter to infinity by turning the threaded lens barrel 7 Screwing the lens in increases the focus distance screwing it out decreases the distance at which the image is focused RoboScan 812 section 4 SERVICE AND MAINTENANCE Changing the Lamp WARNING Read the procedures carefully If you do not feel completely competent to perform
14. de pan tilt auto trigger 2 10 Random sequence wide pan tilt music trigger 1 2 10 Random sequence narrow pan tilt auto trigger 2 3 10 Random sequence narrow pan tilt music trigger 1 2 3 10 Lamp ON 8 10 Lamp OFF 7 10 Adjustment sequence for service use and lamp adjustment 5 10 L E D chase auto trig for service use only 4 10 L E D chase music trig for service use only 1 4 10 Controller Operation Getting Started The RoboScan 812 may be used with DMX 512 and Martin protocol controllers it auto matically determines which protocol is in use Protocol auto detection can be reactivated if necessary by switching on all ten DIP switches and then resetting the address 1 Connect the RoboScan 812 to the controller and set the address Switch on and configure the controller Apply power to the RoboScan After a short reset procedure it will respond to the controller Operation 9 Controllable Effects Lamp After switching on the RoboScan 812 the lamp remains off until a lamp on command is sent from the controller If using a Martin protocol controller the lamp may also be turned off via the controller This feature is not implemented in the DMX protocol to turn off the lamp you must power off the fixture It s important to note that the lamp is a cold restrike type it must be cold before striking is possible The lamp must cool for approximately 5 minutes before it can be turned on again Pan Tilt
15. e factory setting is printed on the serial number label next to the mains input If the voltage is not within 5 percent of the local supply then the ballast and trans former must be rewired Model Selectable Voltages Frequency RoboScan 812 EU 230 V 240 V 250 V 50 Hz RoboScan 812 US 100 V 7 110 V 120 220 V 50 or 60 Hz The RoboScan 812 US may also be used with a 100 V 50 Hz supply when wired for 120 V 60 Hz operation Service and Maintenance 13 14 WARNING Make sure the fixture is disconnected from AC power RoboScan 812 US 1 Remove the cover above the lamp 6 Remove the cover 8 above the circuit board Locate the connection block next to the circuit board Right beside it is a label indicating the proper terminal for each voltage With a small screwdriver loosen the screw in the terminal that holds the BROWN wire Remove the brown wire Tighten the screw Note The BLACK wire must always be connected to the 220 V terminal Loosen the screw for the terminal closest to the supply voltage and insert the BROWN wire Tighten the screw Remove the end plate 5 to access the ballast To set the frequency move the GREY wire on the ballast to the 230 50 50 Hz or 230 60 60 Hz terminal The wire is released and locked by inserting a small screwdriver in the square hole next to the terminal and prying back the spring Tug lightly on the GREY wire to make sure that it is connected securely
16. eflector 1 Set up the RoboScan 812 so that you can access the lamp access plate 12 and if adjusting the lamp without a controller the DIP switch 3 With controller Turn on the RoboScan 812 and allow the lamp to warm up for 5 minutes From the controller select white light with the open gobo and position the beam on a flat white surface Focus the beam Without controller Flip DIP switch pins 1 5 and 10 on Flip all other pins off Apply power to the RoboScan 812 After it has reset the fixture produces a white light with an open gobo for adjustment purposes Wait approximately 5 minutes for the lamp to reach full brightness Position the fixture and or mirror so the light shines on a flat white surface and focus the beam If there is an off center hot spot the lamp is not centered in the reflec tor Pull the hot spot into the center of the field with small adjustments of one or more of the screws 11 Note the Martin Metal Halide lamp is nearly as large as the reflector opening very little side to side adjust ment is possible or necessary If the light is significantly brighter in the center of the field than it is at the edge the lamp is too far forward in the reflector Pull the lamp in by turn ing all three screws clockwise 1 4 turn at a time until the light is evenly distributed If the light is brighter around the edge than it is in the center or if light output is low the lamp is too far back in the re
17. flector Push the lamp out by turning the screws counterclockwise 1 4 turn at a time until the light is bright and evenly distributed If you have made large sideways adjustments disconnect the fixture from AC power allow it to cool and remove the lamp assembly to ensure that the lamp is still placed squarely in the socket RoboScan 812 DMX Mode Selection PL11 654321 7 channel vector mode mmn D 5 channel tracking mode _ g 5 fan connector jumper The DMX mode is set with a jumper on the circuit board inside the unit The factory default is tracking mode Follow the procedure below to change the mode WARNING Make sure the fixture is disconnected from AC power 1 Remove the cover 6 above the lamp Remove the cover 8 above the circuit board 2 Locate connector PL11 on the circuit board refer to the label inside the chassis On one or two of the pins there is a black clip a jumper that creates an electrical connection when placed over 2 pins 3 Place the jumper on pins 4 and 5 to enable 7 channel vector mode Remove the jumper to enable 5 channel tracking mode You can store the jumper by placing it sideways on one of the pins 4 Reassemble the fixture Selecting Voltage The voltage and frequency settings must match the local AC power supply Operating at the incorrect setting can result in poor light output shortened lamp life overheating and dam age to the fixture Th
18. ing and vector mode In tracking mode speed is deter mined by the controller s fade time In vector mode speed is determined by a value pro grammed on a separate DMX channel For smooth movement in vector mode the controller s fade time must be set to 0 i e the position must bump from the current value to the next If the RoboScan 812 is set to run vector mode tracking mode can be enabled by programming the speed channels to 0 DMX DMX Channel Values Percent Effect Strobe SA Reset Lamp ON 0 10 0 4 No strobe 11 74 4 29 Gobo strobe fast gt slow 1 75 138 29 54 Color strobe fast gt slow 139 170 55 67 Remote Auto trig 171 202 67 79 Remote Music trig 203 235 80 92 Reset fixture 236 255 93 100 Lamp power ON Color 0 15 0 6 black gt white 15 30 6 12 white gt color 1 30 45 12 18 color 1 gt color 2 45 60 18 24 color 2 gt color 3 60 75 24 29 color 3 gt color 4 75 90 29 35 color 4 gt color 5 90 105 35 41 color 5 gt color 6 105 120 41 47 color 6 gt color 7 120 135 47 53 color 7 gt color 8 135 150 53 59 color 8 gt color 9 150 165 59 65 color 9 gt color 10 165 180 65 71 color 10 gt color 11 2 180 184 71 72 color 11 185 189 73 74 color 10 190 194 75 76 color 9 195 199 76 78 color 8 200 204 78 80 color 7 205 209 80 82 color 6 210 214 82 84 color 5 215 219 84 86 color 4 220 224 86 88 color 3 225 229 88 90 color
19. ow the work area whenever installing or removing the fixture For protection against dangerous UV radiation never operate the fixture with missing and or damaged covers or lenses installed and do not stare into the light Replace any broken or cracked component immediately Refer all service to a qualified technician Introduction 3 Features e 150 watt discharge lamp 11 dichroic colors plus white 11 gobos plus open and blackout 175 pan movement 83 tilt movement Variable speed control on all functions Split color and gobo effects Variable strobe up to 7 Hz Remote lamp on off with Martin protocol controllers Coated precision optics Adjustable focus e Controllable via Martin and DMX 512 controllers Preprogrammed stand alone operation Music trigger using built in microphone Power factor correction for low current consumption Efficient fan cooling Overheating protection 4 RoboScan 812 section 2 INSTALLATION The RoboScan 812 is delivered fully adjusted from the factory only a few setup steps are necessary Please follow them carefully to get the most out of your new equipment Unpacking The packing material is carefully designed to protect the fixture during shipment always use it or a flight case to transport the fixture The RoboScan 812 comes complete with the following items 150 W Martin Metal Halide discharge lamp 5 meters XLR XLR cable
20. seesteeseeesees 245 mm 190 mm 9 6 7 5 Weight incl bracket EU model s essesessesesssssseseessssesseserssssses 9 4 Kg 20 7 1b Weight incl bracket US model s sssesssssseeessssessssssesessrsssesses 10 5 Kg 23 1 1b Electrical Power and current consumption s ssseseesesseeseeesee 170 W 1 A at 230 V 50 Hz AC voltage and frequency EU model 00 eee 230 240 250 V 50 Hz AC voltage and frequency US model 0 0 100 110 120 220 V 60 Hz FUSE E E EE E E TT 3 15 AT EU 4AT US Compatible Lamps Martin Metal Halide 150 standard ccccccesseeseeseeeseeeseeseeesees P N 97010107 Ostram HAT LIO a nTa aA AR NAAA EEA ER P N 91010108 GE Lighting CSS 150 cssssssscssscnsersensensensenscncseessessesensensenes P N 91010104 Photometric Beaman ANTEE TE TE EE ETE E EET BS 18 RoboScan 812 appendix c DIP SWITCH TABLE This table shows DIP switch settings for channels 1 511 To find a setting locate the chan nel in the table Follow the row to the left to find the settings for pins 1 through 5 follow the column to the top to find the settings for pins 6 through 9 A 0 indicates the pin is turned off and a 1 indicates the pin is turned on Pin 10 is always switched OFF when using the RoboScan 812 with a controller Example The table shows the setting for channel 212 is 00101 for pins 1 5 and 0110 for pins 6 9 Pins 3 5 7 and 8 are set to on pins 1 2 4
21. th two plastic straps and a locking thumbscrew These must be removed before using the RoboScan It is strongly recommended that the pan tilt assembly be locked for transportation by replac ing the thumbscrew in position A over the pan tilt assembly 1 Cut and remove the two plastic straps 2 Remove the thumbscrew over the pan tilt assembly and store it in the threaded hole labelled B on the pan tilt plate 3 Carefully remove the surface protection foil and warning notice from the mirror Installing the Mounting Bracket Use the 11 mm hole in the center of the mounting bracket to fasten a clamp not included or to permanently bolt the fixture in place with a grade 8 8 minimum M10 bolt and lock nut For safety verify that the structure can support at least 10 times the weight of all installed fixtures clamps cables auxiliary equipment etc and always use an approved means of secondary attachment such as a safety cable to prevent falls The mounting bracket may also be used as a floor stand 1 Insert the two black plastic hand wheels into the bracket holes 2 Place a plastic spacer on each hand wheel between the bracket and the casing and screw the hand wheels into the fixture 3 Turn or tilt the RoboScan to the desired position and tighten the hand wheels 6 RoboScan 812 Setup for Controller Operation Connect the Serial Link The RoboScan 812 may be used with DMX and Martin protocol controllers The RoboScan
Download Pdf Manuals
Related Search