Home

the plasmon 8000 series autoloader lf 8120 user manual

Contents

1. DOOR LATCH 2X Figure 29 LF 8120 Media Access Returning the shuttle to home can be accomplished by host command or by pressing LOAD MENU at the DOC If access is authorized the drive will unload the media cartridge into the shuttle move the shuttle to the home position and unlock the electrical safety door lock If access is denied by command from the host pressing LOAD MENU will have no effect and the DOC will briefly display the Denied message PLASMON L MS LF 8120 USER MANUAL Page 70 CARTRIDGE INSERTION LM 8000 media cartridges are inserted directly into the LF 8120 shuttle via the media access door described in the Media Access Door section Ensure that the arrows on the cartridge point toward the shuttle and insert the cartridge into the slot until it is fully seated and its back edge is flush with the edge of the shuttle ENSURE THAT CARTRIDGES DIRECTIONAL ARROWS POINT IN TOWARD THE SHUTTLE INSERTION DIRECTION ARROWS CARTRIDGE SIDE B Figure 30 Media Cartridge Insertion 97664106 A Page 71 CARTRIDGE REMOVAL LM 8000 media cartridges may be removed from the media access door To aid in removing the closely spaced cartridges the top rear
2. Figure 10 Moving the Shuttle Assembly to the Shipping Position 5 Place the LF 8120 into the foam frame so that the drive rests on the bezel relief cushion and the bezel bears no weight 6 Place the lower front foam cushion between the carton and the front of the LF 8120 Place the ESD protective packing material on top of the drive 7 Position the two end cushions which hold the accessories box on the top front and rear of the LF 8120 8 Place the power and interface cables User Manual and other accessories into the options and accessories box and seal with tape Place this box in between the foam end cushions 9 Lower the upper sleeve down onto the lower carton and pallet 10 Strap the carton to the pallet at each end 97664106 A Page 29 PLASMON LMS LF 8120 USER MANUAL Page 30 INSTALLATION AND DE INSTALLATION INSTALLATION REQUIREMENTS Adequate clearances must be provided around the LF 8120 during installation to prevent crimping and bending of cables and to ensure that future servicing can be performed safely These clearances are also required to properly ventilate the LF 8120 and to provide operator access to the DOC and to the media access door for loading and unloading media CAUTION When the LF 8120 is mounted in an equipment rack or cabinet ensure that the internal temperature within the rack or cabinet does not exceed the o
3. Figure 7 Moving the Shuttle to the Home Position 97664106 A Page 23 UNPACKING THE RACK MOUNT CONFIGURATION To unpack the LF 8120 Rack Mount configuration refer to the next figure and perform the following procedure 1 Move the carton to the installation site Unpacking the carton at the installation site minimizes the effects of vibration and shock 2 Cut the tape that secures the top of the box Do not allow the cutting blade to penetrate into the carton 3 Carefully lift the outer corrugated carton up and remove it 4 Remove the accessories box inner carton containing cables and documentation and remove the ESD protective packing material 5 Remove the two cushions which support the accessories box inner carton 6 Carefully lift and remove the LF 8120 from the shipping carton and place it on a flat surface capable of supporting 48 kg 106 lbs A wheeled cart is recommended for transporting the LF 8120 within a building Precautions should be taken to avoid sudden bumps and jarring CAUTION The bezel is slightly larger than the chassis When placing the drive onto a flat surface allow the front end of the LF 8120 to extend over the edge of the supporting surface so that the bezel does not bear any weight 7 Open the media access door and remove the foam insert Manually move the shuttle all the way to the right to the home shuttle position PLASMON LMS LF 8120 USER MANUAL Pa
4. Set all parameters to the default value Set Defaults Set device SCSI identification number 0 through 15 SCSI ID Enable or disable parity checking Parity Set language option to English French or German Language Enable or disable write protect option Wrt Prot Enable or disable media AutoLoad option AutoLoad Enable or disable load switch option Load SW Enable or disable read ahead Rd Ahead Enable or disable Controller Detected Error blink option CDE Curs Enable or disable Busy option Busy Enable or disable Mode Select Read Ahead ModSelRA Enable or disable Media Management Spin Up MMSpinUp Set Target Negotiation Negotiation Viewing diagnostic results or performing diagnostic operations Diagnostics Park the drive in preparation for shipment Park Drive Display the state of the drive sensors Test Sensors Clear the drive initialization variables in nonvolatile memory Clear NVRAM To calibrate the shuttle for correct positioning Cal Shuttle Display controller detected error information View CDEs Change ADP Baud Rate Baud Set Test Start Number Test Start 0 Set Test End Number Test End 0 Set Number of tests to be performed Test Cycles View Real Time Performance Monitor View RTPM Clear RTPM error Clear RTPM Initialize DPC Init DPC Write Power Calibration WPC Options Configuration mode can be entered when the Ready message
5. menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode SETTING THE MODSEL RA OPTION ModSel RA setting determines if the Drive will acknowledge a Mode Select from the host that changes the state of the Read Ahead When disabled the Drive will ignore a MODSEL RA send over SCSI Perform the following procedure to enable or disable the ModSel RA option 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until ModSelRA is displayed 5 Press the SELECT switch to scroll through the states for the load switch on off When the desired state is displayed press MENU to enter the state and move to the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode PLASMON LMS LF 8120 USER MANUAL Page 56 SETTING THE MM SPINUP OPTION When enabled the Media Management Spin Up MM SpinUp option allows the LaserDrive to read necessary media management information during spin up If not enabled the media management information will be recovered on the first media access command Perform the following procedure to enable or disa
6. In case of fire or other emergency isolate the units from the main power by disconnecting the power plugs from their site power receptacles In situations where disconnecting the plugs is not possible or practical use the system main power disconnect to isolate the units from the main power To prevent fire or shock hazard do not expose this unit to rain or moisture Refer servicing to qualified technicians German Translation WARNING Bei der Installation Bedienung und Wartung dieses Produkts bitte immer die folgenden VorsichtsmaBnahmen treffen Dieses Ger t mu an ein Stromversorgungssystem angeschlossen werden das direkt mit einem Erdungsanschlu verbunden ist Terminated Terra Netz TT mit ErdanschluB Dieses Ger t kann nicht an ein ungeerdetes Netz Interrupted Terra IT angeschlossen werden Die Verbindungsschnur des Wechselstromeingangs mu entst rt sein und ihr Minimalstrom unter folgenden Bedingungen bei 10 A liegen Der Nennquerschnitt betr gt 0 75 mm je Leiter Referenz American Wire Gauge Nr 18 es bestehen 2 Dr hte plus ein ErdanschluB und das Produkt entspricht den im Land in dem es aufgestellt wird geltenden Sicherheitsvorschriften Wird das Ger t in ein Ger tegestell oder einen Ger teschrank eingebaut ist darauf zu achten da die interne Temperatur im Gestell oder Schrank nicht ber die in den Produktspezifikationen oder diesem Dokument angegebenen Grenzwerte hinausgeht Um ein o
7. THE PLASMON 8000 SERIES AUTOLOADER LF 8120 USER MANUAL P N 97664106 A CNN Storing More Of Your lasmon Digital World Permanently Reproduction of this manual or any portion of this manual is prohibited without the express permission of Plasmon Laser Magnetic Storage LMS Plasmon LMS reserves the right to make changes in this document and the product referred to herein without prior notice 2000 Plasmon Laser Magnetic Storage WARNING Always observe the following when installing operating or maintaining this product This unit must be connected to a power distribution system that has a direct connection to earth ground Terminated Terra TT network ground connected This unit is not suitable for use on a floating ground Interrupted Terra IT network The AC input power cord must be shielded and must have a minimum current rating of 10 A with a nominal cross section area of 0 75 sq mm reference AWG 18 per conductor 2 wires plus ground and product safety approvals as required for use in the country in which the unit is installed When the unit is mounted in an equipment rack or cabinet be certain that the internal temperature within the rack or cabinet does not exceed the limits defined in the Product Specification or this document To ensure the integrity of safety features of this unit maintenance must be performed only by qualified service personnel using designated Plasmon LMS parts
8. betragt die typische Warmebelastung des LF 8120 ungefahr 364 kcal h 1450 BTU h 97664106 A Page 83 WARNHINWEISE Der LF 8120 ist als Laserger t eingestuft und unterliegt den US amerikanischen Anforderungen bez glich Laserger te Die in Abbildung 5 dargestellten Warnhinweise sind erforderlich um den US Bundesvorschriften nachzukommen Diese Warnhinweise d rfen nicht von den Laufwerken im Gehause des LF 8120 entfernt werden AUSPACHEN DER LF 8120 WARNUNG Um Personenverletzungen zu vermeiden darf der LF 8120 nicht ohne geeignete Hilfsvorrichtungen angehoben werden Beim Auspacken und Transport des LF 8120 ist sicherzustellen daB die Einheit um nicht mehr als 10 Grad gekippt wird Der LF 8120 wiegt ber 181 kg Wenn die Einheit um mehr als 10 Grad gekippt wird kann sie unversehens umfallen und zu Personenverletzungen f hren WARNUNG Um Personenverletzungen zu vermeiden sind zwei Personen erforderlich um den LF 8120 auf einer Rampe nach unten zu rollen Hierbei ist sicherzustellen daB die Einheit um nicht mehr als 10 Grad gekippt wird Der LF 8120 wiegt ber 181 kg Wenn die Einheit um mehr als 10 Grad gekippt wird kann sie unversehens umfallen und zu Personenverletzungen f hren WIEDERVERPACKEN DES LF 8120 Der LF 8120 sollte nur in seiner Originalverpackung wiederverpackt werden Vor dem Wiederverpacken sind die Grundplatten jedes Laufwerks zu schlieBen weiteres hier ber finden Sie unter Schritt 2 im nachfol
9. A Page 9 WARRANTY STATEMENT The LF 8120 is warranted as stated in the purchase agreement between Plasmon and it s customer or the Plasmon sales order acknowledgment whichever is applicable The Plasmon LMS quality system is in compliance and registered to ISO 9001 The LF 8120 is manufactured from new parts or remanufactured parts LF 8120 warranty does not cover defects or damage caused by the use of unauthorized parts or repairs or improper use or maintenance Repairs or replacements not covered by the warranty will be invoiced at LMS then current prices The warranty is void when installation service or repairs are performed by unauthorized personnel when the product is affected by unauthorized alterations modifications or other tampering or misuse when the product is incorporated into a system which causes or involves any changes in the physical mechanical or electrical arrangement of the product or when the product is not used in accordance with its applicable specifications The term authorized personnel is defined as those persons who have been trained by Plasmon LMS Technical Services PLASMON LMS LF 8120 USER MANUAL Page 10 GENERAL DESCRIPTION The LF 8120 Auto Loader is a write once read many WORM high capacity optical disk drive with an integral shuttle capable of holding up to twelve LM 8000 or LM 6000 media cartridges The integral shuttle moves laterally to position one of twelve media cartridges for a
10. USER MANUAL Page 76 OPERATOR MAINTENANCE INSPECTING AND CLEANING FAN AND BLOWER FILTERS Inspect the Filters at the rear of the drive on a 1 6 month schedule and clean if necessary to ensure that cooling air flow is not restricted If the drive is exposed to excessive amounts of dust decrease the time between inspection intervals Remove dust on the drive s exterior with a dry lint free cloth Dust can migrate to the media cartridge and cause performance degradation CAUTION Failure to maintain a clean Filter Element can reduce air flow through the drive This will create high temperatures in the LF 8120 which may shorten the life of the drive Perform the following procedure to clean the Filter Elements Set the drive s AC power switch to the OFF position and verify that the fan and blower have stopped running Remove each Outer Grill Half by grasping its sides and pulling it away from the chassis Remove each Filter Element by pulling it away from the inside of the Grill Wash the Filter Element in warm soapy water Rinse the Element thoroughly and let it air dry Re install the Filter Element in the Outer Grill Half Replace the Outer Grill Half by snapping it onto the inner Grill 97664106 A Page 77 LF 8120 SKIN NOT SHOWN BLOWER FAN FILTER GRILL ASSEMBLY OUTER GRILL HALF EP006058 Figure 35 Removing Filter Element REPLACING FUSES As stated
11. connected to a host computer in a daisy chained configuration using the appropriate SCSI controller and cable options When the single ended interface controller is used on all SCSI devices the total length of the SCSI interface cable cannot exceed 6 m 19 5 ft Plasmon LMS does not recommend single ended fast synchronous When a differential interface controller is used on all SCSI devices the total SCSI interface cable length cannot exceed 25 m 82 ft NOTE The internal SCSI cable for each LF 8120 is approximately 22 86 mm 9 0 in This distance must be considered as part of the total SCSI cable length The SCSI interface cabling used to interconnect an LF 8120 to a host can be daisy chained between SCSI devices as illustrated below One interface cable is required to interface each pair of SCSI devices Any Single Ended configured Drive that is placed on a Low Voltage Differential Single Ended bus LVD SE bus must be terminated using a standard SCSI SE terminator on at least one end of the SCSI bus for proper operation HOST LF 8120 LF 8120 LF 8120 HOST SCSI SCSI SCSI SCSI CONNECTOR CONNECTORS CONNECTORS CONNECTORS eee TERMINATOR NOTE The SCSI bus must also be terminated at the host Normally the termination function is built into the host adapter 8K SCSI_DAISY vsd Figure 11 Host to LF 8120 Daisy Chain Cable Connections A
12. edge of the shuttle is cut away and a notch is provided on the exposed edge of each cartridge Pulling on the cartridge notch with one finger as shown in the next figure will back the cartridge out far enough so that it can be grasped and removed Figure 31 Media Cartridge Removal PLASMON LMS LF 8120 USER MANUAL Page 72 MANUAL CARTRIDGE RELEASE MECHANISM If power fails or if the drive fails with a media cartridge inserted the media cartridge can be manually removed by opening the drive baseplates removing the bezel and then retracting the cartridge OPENING THE BASEPLATES With the manual release tool perform the following procedure 1 Move the AC power switch to the OFF O position and disconnect the AC power cable from the wall outlet 2 At the rear panel insert the manual release tool into the upper access hole and engage the recessed D shaped shaft Turn the tool handle counterclockwise as far as it will turn to open the upper baseplate 3 Repeat step 2 at the lower access hole to open the lower baseplate LF 8120 SKIN MANUAL RELEASE TOOL d NOT SHOWN REAR PANEL LOWER ACCESS HOLE Figure 32 Manually Opening the LF 8120 Baseplates 97664106 A Page 73 RETRACTING THE CARTRIDGE Use the following procedure to manually retract a cartridge 1 Insert the manual release tool onto the D shaped shaft at the front of the drive as shown in the figure above to operate the cartridge insertion m
13. einem ausgebildeten Ingenieur des Kundendienstes durchgef hrt werden EINSTELLEN DER INTERNEN LAUFWERKSSERIENNUMMER SERIENNR EINSTELLEN HINWEIS Die Seriennummer die dem Laufwerk zugeordnet wird muB mit den letzten 5 Ziffern der tats chlichen Seriennummer des Laufwerks bereinstimmen damit eine exakte interne Ereignisprotokollierung stattfinden kann Die tats chliche Seriennummer des Laufwerks befindet sich an der R ckseite des Laufwerksgeh uses HANDHABUNG VON DATENTRAGERKASSETTEN Achten Sie bei der Handhabung und Lagerung von Datentragerkassetten auf die folgenden VorsichtsmaBnahmen um die Datenintegritat zu sichern 1 Die Datentr gerkassette niemals auf harte Fl chen fallen lassen 2 Das Kassettengeh use oder den Zugriffsmechanismus nicht miBbrauchen QD Die Datentr gerkassette nicht im Laufwerk lagern Die Kassetten vor einem Transport aus dem Laufwerk entfernen C1 Etiketten nur an den vorgesehenen Stellen anbringen O Die Datentr gerkassette vor direkter Sonneneinstrahlung und Kondensation sch tzen PLASMON L MS LF 8120 USER MANUAL Page 88 VORSICHT Zur Vermeidung einer Beschadigung der Datentrager wird dringendst empfohlen die in der Spezifikation f r LM 8000 Datentrager angegebenen Umgebungsbeschrankungen sorgfaltig zu beachten 7 Die Datentragerkassette nicht extremen Temperaturen aussetzen 8 Die Datentragerkassette eine Stunde vor Gebra
14. enter the language option and move to the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the Main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode PLASMON LMS LF 8120 USER MANUAL Page 52 SETTING THE WRITE PROTECT OPTION The write protect option enables the user to inhibit the LF 8120 from writing to any media inserted into the drive regardless of the write protect setting on the media cartridges Perform the following procedure to turn write protect on or off 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until Wrt Prot is displayed 5 Press the SELECT switch to scroll through the states for write protect off on When the desired state is displayed press MENU to enter the state and move to the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the Main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode NOTE The Write Protect indicator on the DOC is illuminated when write protect is enabled SETTING THE MEDIA AUTOLOAD OPTION The media AutoLoad load option enables a user to cho
15. parity checking on or off 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until Parity is displayed 5 Press the SELECT switch to scroll through the states for parity checking on off When the desired state is displayed press MENU to enter the state and move to the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the Main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode SETTING THE LANGUAGE The language option enables the user to select the language used by the LF 8120 to display messages in the Operating mode English is the only available language for Configuration mode Perform the following procedure to set the operating mode display language 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until Language is displayed 5 Press the SELECT switch to scroll through the language display options Eng English Frh French Grm German When the desired language option is displayed press MENU to
16. require the attention of a trained Customer Engineer CE to repair the drive Clearing this error without resolving the cause may reduce the total media capacity because of abnormally high relocations during write operations Press the SELECT switch if an RTPM error has not occurred the message No RTPM Err will briefly appear and the display will return to Clear RTPM If an RTPM has occurred a confirmation message will be displayed Press the SELECT switch to clear the RTPM error and enable writing Press the MENU switch to select the next option in the Diagnostic Park Drive menu without clearing the RTPM error The drive will not perform write operations with an RTPM error Init DPC Press SELECT switch to Initialize DPC This option will clear all the serial E Prom values and reset the drive WPC Options Press the SELECT switch Force WPC is displayed If Write Calibration is required press the SELECT switch again The Drive will cycle through the WPC Write WPC GOOD and back to Force WPC messages Press the MENU switch to display Clear WPC If the WPC log needs to be cleared from the Drive press SELECT again When the WPC Log has been cleared the message WPC CLEARED will be momentarily displayed When Clear WPC is displayed press MENU and MENU SELECT simultaneously to return to the Diagnostic Menu A structure diagram for the Diagnostics menu is shown in the next figure To move up level in the configuration menu hie
17. terminator must be installed on the vacant connector of the last SCSI device in the SCSI bus chain The SCSI bus must be terminated externally on the LF 8120 rear panel when an LF 8120 is the last SCSI device on the bus 97664106 A Page 33 You must first determine the type of termination your host system requires In a daisy chain configuration a terminator must be used on both the first and last devices on the bus One of these devices may be the host adapter All other LF 8120 s between the first and last device in the daisy chain should not be terminated NOTE Installation of both an active single ended terminator and a passive single ended terminator on the same bus is not recommended If only one LF 8120 is attached to a host the bus must be terminated at the host adapter and the LF 8120 Normally the termination function is built into the host adapter Power for the external terminator is supplied by the LF 8120 and may also be supplied by another device in the SCSI daisy chain Terminator power for external terminators is provided by the LF 8120 power supply HOST LD 8120 HOST SCSI SCSI CONNECTOR CONNECTORS gt TERMINATOR TERMINATOR Figure 12 LF 8120 to Host Cable Connection PLASMON LMS LF 8120 USER MANUAL Page 34 CONNECTING POWER AND SCSI CABLES After the LF 8120 has been installed in its operating location re
18. the Main menu Simultaneously press the LOAD MENU and TEST SELECT Switches again to exit Configuration mode SETTING THE SCSI ID The SCSI ID can be set to one of 16 device Identification ID numbers 0 through 15 however each device connected to the same SCSI bus must have a unique SCSI ID Perform the following procedure to set the LF 8120 s SCSI ID number 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until SCSI ID is displayed 5 Press the SELECT switch to scroll through the options for the SCSI ID value 0 through 15 When the desired value is displayed for the SCSI ID press MENU to enter the SCSI ID value and move to the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the Main menu Simultaneously press the LOAD MENU and TEST SELECT Switches again to exit Configuration mode NOTE After resetting the device ID turn the drive off wait 5 sec and then turn the drive on again This ensures that the new device ID will be acknowledged by the SCSI bus 97664106 A Page 51 SETTING THE BUS PARITY CHECKING SCSI bus parity generation is always enabled however SCSI bus parity checking at the drive can be disabled Perform the following procedure to turn
19. the conditions and limits for shock and vibration Table 4 Shock and Vibration Criteria and Limits CONDITION OPERATING NONOPERATING STORAGE TRANSIT Swept Vibration 5 to 250 Hz 0 1 g Peak 5 to 44 Hz 0 03 in 5 to 44 Hz 0 03 in Bidirectional 250 to 500 Hz Double Amplitude Double Amplitude 1 Octave Min 0 25 g Peak 44 to 500 Hz 44 to 500 Hz 3 0 g Peak 3 0 g Peak Shock 2 10 msec Half Sine Pulse Host Retries May Be of 2 5 g Peak with pulses Required and Drive applied every 3 sec Performance May Degrade During Test Unpacked 3 Axis 5 msec Half Sine Pulse of 20 g Peak Packed on Pallet 46 cm 18 in Drop Test Flat 1 With media removed 2 In LMS approved packaging 3 Shock repetition rate should be limited to allow mechanical system transients to subside between pulses 97664106 A Page 17 AC POWER REQUIREMENTS The LF 8120 has a grounded power connector integrated into the AC power switch Over current protection is provided by two fuses integrated into the AC power switch Two spare fuses are included within the power connector Refer to the Operator Maintenance section for the fuse replacement procedure The drive s power supply accepts the input line voltages listed in the table below The power supply is auto ranging and does not require mechanical switching for input voltage or frequency selection Table 5 AC Power Requirements READY 1 SPIN AC LINE MS bus PEAS U
20. 8 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode 97664106 A Page 57 VIEWING DIAGNOSTIC RESULTS OR PERFORMING DIAGNOSTIC OPERATIONS DIAGNOSTICS To enter the diagnostic submenu press the TEST SELECT switch while Diagnostics is displayed in the Main menu The drive will enter the Diagnostics menu which includes the following options Park Drive Press the SELECT switch to park the baseplates for drive shipment If the Park Failed Close Manually message appears refer to the Manual Release section of this manual Press the MENU switch to select the next option in the Diagnostics menu Test Sensors Press the SELECT switch to enter sensor display mode In sensor display mode the panel will display the status of the sensors within the drive For details see the LF 8120 Hardware Maintenance Manual P N 97663082 Press the MENU switch to select the next option in the Diagnostics menu Clear NVRAM CAUTION Since the initialization variables cannot be recovered once they are cleared this operation should only be performed by a trained Customer Engineer CE Press the SELECT switch the message Drive will reset and NVRAM will be cleared To Continue Press Select will appear Press the MENU switch if you do not want to clear the nonvolatile memory NVRAM initialization variables press
21. Cartridge Writing Eriture Schreibend Unload Cartridge Unloding Decharge Entladend Removing Cartridge Removing Retir Disk Entfernend Moving to Cartridge Moving to Deplace Gehe Zu Cartridge Positioned Positioned Positione In Pos Shuttle in Home Position Home Origine Ruheposition Drive is in Rest SCSI reset SCSI Reinit SCSI Reinit Illegal Request Spindown Disabled Denied Refuse Abgelehnt Door Locked Drive is Testing Itself Selftest Autotest Selbsttest Drive is Scanning Media Scanning Scanning Media Pr f Insert Cartridge Inserted Insere Eingelert Shuttle is being Initialized Init Shuttle Init Shuttle Shuttle Init Slot in Shuttle is Empty Empty Vide Leer Door is Open Door Open Porte Ouvert Ture Offen Shuttle Moving to Home Position Move to Home Depl Origine Zur Ruhepos 1 Locked means that the host has issued a PREVENT MEDIA REMOVAL command PLASMON LMS LF 8120 USER MANUAL Page 42 CONFIGURATION MODE Configuration mode is used to view and set drive operating parameters The parameters that can be configured and displayed are summarized in the following the corresponding DOC display is shown in parentheses View the current operating parameters View Current View the firmware revisions of the drive View FW Revs View the hardware revisions of the drive View HW S Ns View the hardware part numbers of the drive View HW P Ns
22. HE SET SERIAL MENU IN Digit to be Set is Flashing sw 11 2 3 4 s Figure 24 Set Serial Menu PLASMON L MS LF 8120 USER MANUAL Page 64 TEST MODE The LF 8120 automatically enters the Test mode each time the Drive is powered on Power on selftest diagnostics are run to verify the operational readiness of the drive After the LF 8120 successfully passes the power on selftests the LF 8120 enters the Operating mode While the Drive is in the Operating mode the operator may manually enter the Diagnostic Test mode The level of selftest diagnostic coverage is configurable via the Test Start Test End and Test Cycles options in the Diagnostics menu Diagnostic tests 0 through 7 verify basic drive hardware operation Test number 9 will Write Power Calibrate the current media in the Drive To perform any of the diagnostic test From the Operating Mode enter the Diagnostic menu and follow the steps in the flow chart below ENTER DIAGNOSTIC MENU DIAGNOSTICS PRESS MENU REPEATEDLY UNTIL TEST START 0 IS DISPLAYED 0001 9999 SWITCH BACK TO THE DIAGNOSTIC MENU PRESS BOTH SWITCH BACK TO THE OPERATING MENU feu seLecr gt SWITCHES SIMULTANEOUSLY START TESTING Cseuzcr 7 FOLLOW INSTRUCTIONS DISPLAYED ON THE DOC Figure 25 Entering Diagnostic Tests When errors are detected the appropriate diagnostic message will be displayed on the DOC Diagnostic messages are presented to the oper
23. IC RESULTS OR PERFORMING DIAGNOSTIC OPERATIONS DIAGNOSTICS SET THE INTERNAL DRIVE SERIAL NUMBER SET SERIAL TEST MODE MEDIA CARTRIDGE HANDLING SETTING THE WRITE PROTECTION SWITCH AFFIXING LABELS MEDIA INSERTION AND REMOVAL CARTRIDGE INSERTION CARTRIDGE REMOVAL MANUAL CARTRIDGE RELEASE MECHANISM OPENING THE BASEPLATES RETRACTING THE CARTRIDGE MEDIA LOADING OPERATOR MAINTENANCE INSPECTING AND CLEANING FAN AND BLOWER FILTERS REPLACING FUSES MEDIA CLEANING MEDIA CLEANING USING CLEANING KIT P N 97662550 APPENDIX A GERMAN TRANSLATIONS UBERSETZUNGEN INS DEUTSCHE 77 77 78 80 80 81 81 5 This User Manual describes unpacking installing operating and maintaining the Plasmon LF 8120 Auto Loader High Performance Optical Disk Drive RELATED PUBLICATIONS Publication Part Number LD 8100 LF 8120 LF 8600 LF 8602 Product Specification 97663035 LD 8100 LF 8120 LF 8600 LF 8602 SCSI Interface Specification 97662164 LF 8120 Hardware Maintenance Manual 97664107 NOTICES Three levels of notices are used throughout this document WARNING A WARNING is used to alert the reader of situations or conditions that could potentially result in personal injury fire hazard or equipment damage CAUTION A CAUTION is used to warn of undesirable procedures or of situations in which equipment damage could potentially result NOTE A NOTE is used to emphasize an area of text or to provide additional information 97664106
24. OLE IS CLOSED WRITE PROTECT SWITCH AND INDICATOR ON OTHER SIDE EP004350 Figure 27 Manually Write Protecting the Media Cartridge PLASMON LMS LF 8120 USER MANUAL Page 68 AFFIXING LABELS Title and content labels are supplied with each LM 8000 media cartridge and should be affixed before the cartridge is inserted into the LF 8120 Before affixing the labels in the recessed areas see figure below ensure that the surface of the cartridge is clean and dry SIDE A VIEW POSITION LABELS HERE Figure 28 Label Placement 97664106 A Page 69 MEDIA INSERTION AND REMOVAL Individual media cartridges are inserted and removed through the front panel media access door When fully closed the door is held by magnetic contacts A safety switch prevents operation of the shuttle if the door is open When the door is opened and closed the drive tests the six slots to determine which slots have media cartridges present The door is automatically locked by a electrical safety lock when the drive begins operation An independent manual key lock located in the bezel assembly provides an additional locking method for preventing unauthorized media access Operator access to the media requires the shuttle to be in the home position The home shuttle position squarely aligns all six cartridge slots with the media access door as illustrated in the next figure SAFETY LOCK ES LATCH KEY LOCK
25. P DN MIN SERVICE VOLTAGE a CYCLE EVERY RATING SPIN UP Ta 95 0V TO 128V 1 4A 110W 10A 2 0A 160W 7 15A 173 0 TO 268V 0 7 110W 5A 1 0A 160W 15A 1 This current measurement determines the stated power and maximum heat dissipation of the Drive 546 BTU hr based on RMS current over the 10S cycle derated by the Power Factor It also determines the 2 0 A UL plate rating NOTE After the power has been turned off the operator must wait 1 second before turning on the power again AC GROUND The LF 8120 chassis should be connected to earth ground for operator safety The AC power cord has a grounding conductor which connects the LF 8120 chassis to safety ground through the site AC power system If the site AC system ties its ground wire connection to earth ground then the LF 8120 chassis will also be tied to earth ground All site AC power connections must be maintained on the same safety ground A line grounding connector located on the rear panel can also be used to tie the LF 8120 chassis to earth ground This ground connector is a 6 mm 0 24 in M4 with a nut and lock washer AC POWER CORD The type of AC power cord supplied with the LF 8120 will depend upon the configuration ordered POWER SUPPLY PROTECTION FEATURES The LF 8120 power supply provides over and under voltage protection over current protection power failure detection and over temperature protection Should an out of range condition be detected th
26. PANEL DOC The LF 8120 front panel see figure on the right includes a Drive Operator Console DOC media access door and door lock BEZEL within a bezel assembly Refer to the Operating Instruction section of this MEDIA manual for a detailed description of the ACCESS DOC DOOR KEY LOCK ee SOME QE o mj u o REAR PANEL The LF 8120 rear panel contains the power switch along with AC power connector and fuses the ground connector and external interface connectors SCSI 2 I O CONNECTORS MANUAL RELEASE ACCESS HOLE AUXILLIARY DIAGNOSTIC PORT ADP BLOWER GRILL AND FILTER ELEMENT AC POWER SWITCH AC POWER RECEPTACLE FAN GRILL AND FILTER ELEMENT MANUAL RELEASE ACCESS HOLE Figure 3 LF 8120 Rear Panel PLASMON LMS LF 8120 USER MANUAL Page 14 DIMENSIONS AND WEIGHT The table below lists the reference dimensions of the LF 8120 configurations Table 1 Dimensions of the LF 8120 Configurations DIMENTION RACK MOUNT TOWER Length 75 57 CM 29 75 IN 75 57 CM 29 75 IN Width 45 10 CM 17 75 IN 45 10 CM 17 75 IN Height 47 0 CM 18 5 IN 58 42 CM 23 0 IN SHIPPING WEIGHT The LF 8120 shipping weight is listed below These v
27. R LASER CLASS LABEL LABEL CANADIAN CLASS A LABEL FCC RFI CLASS A LABEL Figure 4 Location of LF 8120 Warning Labels 97664106 A Page 19 PLASMON LMS LF 8120 USER MANUAL Page 20 UNPACKING AND REPACKING INSTRUCTIONS The LF 8120 is shipped with foam packing material which protects the unit from shock and vibration When you receive your LF 8120 inspect the shipping carton for damage before unpacking the unit to substantiate a claim with the carrier if the unit is damaged Retain all original packing materials for possible reshipment WARNING The LF 8120 must be unpacked repacked and transported by two persons Physical injury can result if one person attempts to lift the LF 8120 A wheeled cart is recommended for transporting the LF 8120 within a building Precautions should be taken to guard against sudden bumps and jarring UNPACKING THE TOWER CONFIGURATION The LF 8120 is packaged as illustrated in the next figure The top bottom and sides of the LF 8120 are protected from shock and vibration by foam cushions The top cushions are also used to hold the accessories box inner box which is placed between the blocks of foam To unpack the unit 1 Move the carton to the installation site Unpacking the carton at the installation site minimizes the effects of vibration and shock 2 Cut the tape and straps that secure the top of the box Do n
28. RUHE TRANSPORT Wobbelvibration 5 bis 250 Hz 0 1 Zoll 5 bis 44 Hz 0 03 Zoll 5 bis 44 Hz 0 03 Zoll Bidirektional Doppelamplitude Doppelamplitude Doppelamplitude 44 bis 500 Hz 3 0 g Peak Stoss Hostwiederholungen Sind U u Erforderlich Und Laufwerksleistung Kann Sich Wahrend Des Tests Verschlechtern 10 msek Halb Sinusimpuls Von 2 5 g Peak Unverpackt 5msek Halb 3 Achsen Sinusimpuls 20 g Peak Verpackt Auf Verpackt Auf Palette Palette 46 cm Fallversuch Flach 1 Mit entfernten Datentr gern 2 In LMS genehmigter Verpackung 3 Die H ufigkeit wiederholter Sto einwirkungen ist so weit gering zu halten da mechanische bzw elektrische St rungen zwischen den einzelnen St en wieder nachlassen WECHSELSTROMBEDARF Der prim re Netzkabeltyp h ngt von der bestellten Konfiguration f r den LF 8120 ab Das prim re Netzkabel versorgt die Steckdosenleiste im Geh use des LF 8120 mit Strom PLASMON LMS LF 8120 USER MANUAL Page 82 Jeder LF 8120 ist Uber ein geerdetes Netzkabel an die Steckdosenleiste angeschlossen Beim LF 8120 ist der Verbindungstecker in die Netzsteckdose integriert Schutz gegen Uberlaststrom wird durch zwei Sicherungen gew hrleistet die zusammen mit zwei Reservesicherungen in die Netzsteckdose integriert sind Das Netzteil jedes Laufwerks erfordert die in Tabelle 3 angegebenen Netzspannungen Das Netzteil ist selbstregulierend und erfordert kein mechanisches Schalt
29. alues do not include media cartridges Rack Mount 71 21 kg 157 lbs Tower 75 75 kg 167 lbs The weight of one LM 8000 cartridge is approximately 1 18 kg 2 6 Ibs 97664106 A Page 15 TEMPERATURE HUMIDITY AND ALTITUDE The following table lists the LF 8120 operating storage and transit limits for temperature humidity and altitude Table 2 Temperature Humidity and Altitude Limits CONDITION OPERATING NONOPERATING STORAGE TRANSIT Temperature 10 to 42 50 to 108 F 40 to 66 40 to 151 40 66 40 to 151 Change 11 C hr 20 F hr 20 C hr 36 F hr 20 C hr 36 F hr Change Humidity 10 to 90 5 to 95 5 to 95 Noncondensing Maximum Rate of 10 hr 10 hr 10 hr Maximum Wet Bulb Temperature 3 28 C 82 F 46 C 115 F 46 C 115 F Minimum Dew Point 2 C 35 6 F 2 C 35 6 F 2 C 35 6 F Altitude 300 to 3 000 m 984 to 9 840 ft 300 to 3 000 m 984 to 9840 ft Storage 300 to 3 000 m 984 to 9 840 ft Transit 300 to 12 000 m 984 to 40 000 ft cations are based on a maximum 1 week period in a factory sealed container temperature is derated linearly above 300 m altitude to 38 C at 2 000 altitude perature and humidity operating range PLASMON LMS LF 8120 USER MANUAL Page 16 1 Storage specifications are for 90 day
30. ately after you have replaced the original fuse contact your next level of support Do not replace the spare fuse This may be a symptom of a more serious problem either with the power supply or the power system 97664106 A Page 79 MEDIA CLEANING Media disk surfaces should be inspected periodically and cleaned on an as needed basis MEDIA CLEANING USING CLEANING KIT P N 97662550 The Cleaning Kit P N 97662550 provides a semi automated cleaning method for cleaning the Plasmon LM 4000 LM 6000 and LM 8000 12 inch optical media Follow the procedures given in the enclosed Cleaning Instructions The Kit contains the following items One 12 inch media cleaning fixture Two containers of cleaning liquid Five packages of cleaning tissues One pair of protective gloves Cleaning Instructions PLASMON LMS LF 8120 USER MANUAL Page 80 APPENDIX GERMAN TRANSLATIONS UBERSETZUNGEN INS DEUTSCHE ABMESSUNGEN UND GEWICHT Die Bezugsabmessungen f r den LF 8120 wie auch aus Abbildung 4 ersichtlich betragen wie folgt Hohe 75 57 cm Breite 45 10 cm Tiefe 58 42cm Der LF 8120 wiegt 75 75 kg TEMPERATUR LUFTFEUCHTIGKEIT UND SEEHOHE In Tabelle 1 sind die Temperatur Luftfeuchtigkeits und Meeresh hengrenzwerte f r die im LF 8120 installierten LF 8120 Laufwerke aufgef hrt Tabelle 1 Temperatur Luftfeuchtigkeits und H hengrenzwerte LAGERUNG BEDINGUNG BETRIEB RUHE TRANSPORT Temperatur 10
31. ator in the form of failed test codes and Field Replaceable Unit FRU mnemonics that can be relayed to a CE for repairing the malfunction If no problems are detected by the system function diagnostics the display will show Diagnostics Complete Press TEST to restart drive Pressing TEST resets the Drive 97664106 A Page 65 MEDIA CARTRIDGE HANDLING The LM 8000 or LM 6000 media cartridge may be used in all LD 8100 LF 8120 LF 8600 LF 8602 drives The media cartridge is shipped ready for immediate use and does not require preformatting before use The LF 8120 accesses both sides of the media cartridge see next figure The LM 8000 cartridge must be inserted with side A facing right while the LM 6000 cartridge may be inserted into the LF 8120 with either side facing left SIDE A VIEW MEDIA LOADING P d NOTCHES CARTRIDGE DOOR BOTH SIDES COLOR PLUG FOR CARTRIDGE ID MEDIA DIRECT LABEL 2 PROT CT SWITCH AND INDICATOR BLOCKED GRIPPER HOLE Figure 26 LM 8000 Media Cartridge The media cartridge also has a write protect switch which write protects both sides of the media when the Switch is in the active position PLASMON L MS LF 8120 USER MANUAL Page 66 Observe the following precautions to ensure data integrity when handling or storing a media cartridge 1 Do not drop the media cartridge onto hard surfaces 2 Do not physically abuse the cartridge exterior or access mechanisms 3 Do not s
32. bis 42 C2 40 bis 66 C 40 bis 66 C Maximale 11 C h 20 C h 20 C h Anderungsrate Luftfeuchtigkeit 10 bis 90 5 bis 95 5 bis 95 Nicht Kondensierend Maximale 10 h 10 h 10 h Anderungsrate Maximale 28 C 46 C 46 C Feuchtkugel temperatur Minimale Taupunkt 2C 2C 2C Seeh he Lagerung 300 bis 3000 m 300 bis 3000 m Transport 300 bis 12000 m 97664106 A Page 81 1 Die Lagerungsangaben beziehen sich auf maximal 90 Tage in der Plasmon LMS Verpackung Kondensation ist nicht zul ssig Die Transportangaben gelten f r maximal I Woche in einem werkseitig verschlossenen Beh lter 2 Falls nicht anders angegeben ist die maximale Betriebstemperatur f r ein freistehendes Laufwerk auf Meeresh he 42 C Die maximale Betriebstemperatur ber 300 m H he wird bei 2000 m H he linear auf 38 C herabgesetzt 3 Weitere Informationen zu Temperatur und Luftfeuchtigkeitsgrenzwerten im Betriebszustand finden Sie in der Produkts pezifikation f r den LD 8100 LF 8600 LF 8120 4 F r Datentr ger gilt ein Grenzwert von 2000 m Umgebungsbedingungen und Grenzwerte f r Datentr ger finden Sie in der Produktspezifikation fiir den LM 8000 Datentr ger STOSS UND VIBRATION In Tabelle 2 sind die StoB und Vibrationskriterien und grenzwerte f r den LF 8120 angegeben Tabelle 2 StoB und Vibrationskriterien und Grenzwerte 1 Oktave Minute 250 bis 500 Hz 0 25 g Peak 44 bis 500 Hz 3 0 g Peak LAGERUNG BEDINGUNG BETRIEB
33. ble the MM SpinUp option 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until MMSpinUp is displayed 5 Press the SELECT switch to scroll through the states for the load switch off on When the desired state is displayed press MENU to enter the state and move to the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode SELECT TARGET NEGOTIATION The Negotiation menu allows the Drive to be set to initiate the NEGOTIATE for SCSI Wide and SCSI Synchronous communication Perform the following procedure to enable or disable the MM SpinUp option Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously Press the MENU switch until Set Config is displayed Press the SELECT switch to enter the Set Configuration menu Press the MENU switch until Negotiation is displayed a A OO Press SELECT switch TargSDTR is displayed Press SELECT to toggle between OFF or ON 6 When the desired selection has been made press MENU to display TargWDTR 7 Press SELECT to toggle between OFF and ON
34. e LF 8120 will shut down the DC outputs of the power supply After the situation is corrected power can be restored by turning the AC power switch to the off position and then to the on position again PLASMON L MS LF 8120 USER MANUAL Page 18 TILT RANGE The LF 8120 is not designed for use when tilted from the vertical position HEAT DISSIPATION The drive will typically present a heat load of 95 kg calories hr 376 BTU hr during a read write operation When media cartridges are inserted loaded spun up spun down unloaded and removed at the drive s maximum rate the LF 8120 will typically present a heat load of 138 kg calories hr 546 BTU hr PARTICULATE LIMITS The LF 8120 is designed for use in an office or computer room The environment must have a low dust level The LF 8120 filters incoming air for cooling to reduce the quantity of particles entering the drive however the filter is not effective against small particles including tobacco smoke which will become deposited on optical components and media causing degradation in drive performance Refer to the Operator Maintenance section for media cleaning and air filter cleaning instructions WARNING LABELS The LF 8120 is classified as a laser product and meets all United States federal requirements The warning labels shown in the figure below have been applied to the Drive to ensure compliance with federal regulations and must not be removed from the LF 8120 LASER DANGE
35. echanism Turn the tool clockwise as far as it will turn pulling the cartridge back into the shuttle INSERT MANUAL RELEASE TOOL HERE Figure 33 LF 8120 Manual Cartridge Retraction 2 Manually move the shuttle to the home position as shown below 3 Remove the cartridge from the shuttle slot PLASMON LMS LF 8120 USER MANUAL Page 74 MANUALLY MOVE THE SHUTTLE TO THE LEFT INTO THE SHIPPNG POSITION Figure 34 Manually Moving the Shuttle Assembly to the Home Position MEDIA LOADING Individual media cartridges can be selected for loading by host command or by the autoload configuration option The host can select and load a media cartridge from any shuttle slot by issuing an appropriate SCSI bus command Selection by the autoload configuration option occurs at initial power up and when the LOAD MENU switch on the DOC is pressed while the LF 8120 is in Operating mode Depending on the setting of the autoload option the LF 8120 automatically inserts and loads one specified media cartridge or the most recently used MRU cartridge or moves the shuttle to the home position If the selected cartridge is not present the DOC displays Empty where represents cartridges 1 12 For more information on viewing and setting drive configuration options refer to the Configuration Mode section of this manual 97664106 A Page 75 PLASMON LMS LF 8120
36. en der Eingangsspannung oder Netzfrequenz Tabelle 3 Wechselstrombedarf LEISTUNG EINSCHALT NENNLEISTUNG FREQUENZ WECHSELSPANNUNG TYPISCH STROMSTOSS1 MIN 47 bis 66 Hz 95 0 V bis 128 V 14A 10 0A 15A 47 bis 66 Hz 173 4 bis 268 V 0 7 A 5 0A 15A 1 Weniger als 1 Sek Kaltstarthinweis HINWEIS Nach Ausschalten des Stroms m ssen Sie 1 Sekunde warten bevor der Strom wieder eingeschaltet werden darf WECHSELSTROMERDUNG Um einen sicheren Betrieb zu gew hrleisten muB das Gehause des LF 8120 geerdet sein Das Wechselstromkabel enth lt eine Erdleitung die das Geh use des LF 8120 durch die Wechselstromversorgung des Standorts an Sicherheitserde legt Die Wechselstromversorgung des Standorts wiederum muB diese Erdung an einen ErdanschluB legen Alle Wechselstromverbindungen am Standort m ssen denselben ErdanschluB verwenden Ein ErdanschluBteil an der Ger ter ckseite vgl Abschnitt 2 2 kann ebenfalls dazu verwendet werden den LF 8120 an einen Erdanschluf zu legen Dieser ErdanschluBteil ist ein 6 mm M4 Bolzen mit Mutter und Sicherungsscheibe KIPPTOLERANZ Erm glicht den Kippbetrieb von der waagrechten Stellung WARMEAUSSTRAHLUNG Das Geh use des LF 8120 weist wahrend eines Schreib Lesevorgangs eine typische Warmebelastung von 292 kcal h 1160 BTU h auf Wenn Datentragerkassetten mit der Maximalgeschwindigkeit des Laufwerks eingelegt geladen aktiviert deaktiviert entladen und entfernt werden
37. enu Press the SELECT switch to display the drive firmware revisions These include firmware revisions for the WOODI DPC RWS A and RWS B Press the MENU switch to select the next option in the View Configuration menu Press the SELECT switch to display the serial numbers These include serial numbers for the Drv SN Woodi Rws A Rws B Oma A Oma B and Dpc Press the MENU switch to select the next option in the View Configuration menu Press the SELECT switch to display the hardware part numbers These include part numbers for WOODI RWS A RWS B and DPC Press the MENU switch to select the next option in the View Configuration menu Table 9 View Configuration Messages OPTION CURRENT DEFAULT FACTORY NAME SETTING SETTING SCSI ID 40 15 0 Parity On or Off On Language Eng Frh or Grm Eng Wrt Prot On or Off Off AutoLoad Slot 1 12 or MRU 1 Load SW On or Off On Rd Ahead On or Off Off CDE Curs On or Off Off Busy On or Off On ModSelRA On or Off On MMSpinUp On or Off Off TargSDTR On or Off On TargWDTR On or Off On PLASMON LMS LF 8120 USER MANUAL Page 46 A structure diagram for the View Configuration menu is shown in the next figure To move up a level in the Configuration menu hierarchy to the Main menu press the LOAD MENU and TEST SELECT switches simultaneously To exit the Configuration mode press the LOAD MENU and TEST SELECT switches simultaneously The display wi
38. eously The display will show the message which appeared prior to the drive entering the Configuration mode Eus Decem tun SET DEFAULT TO DEFAULT PRESS BOTH SWITCHES SIMULTANEOUSLY FROM SET CONFIG TO RETURN TO THE MAIN MENU SET CONFIG MENU PRESS BOTH SWITCHES SIMULTANEOUSLY FROM ANY MENU TO RETURN TO SET CONFIG LANGUAGE FROM LAST MENU SELECTION Figure 20 Set Config Menu Part 1 97664106 A Page 49 PRESS BOTH SWITCHES SIMULTANEOUSLY FROM SET CONFIG TO RETURN TO THE MAIN MENU OFF Y ON SET CONFIG MENU ON Y PRESS BOTH SWITCHES OFF SIMULTANEOUSLY FROM ANY MENU TO RETURN TO SET CONFIG ON Y OFF ON Y OFF CYCLE BACK TO TOP OF MENU ao SIMULTANEOUSLY Figure 21 Set Config Menu Part 2 PLASMON LMS LF 8120 USER MANUAL Page 50 SET DEFAULTS The SET DEFAULT function will reset all operating parameters to factory defaults Perform the following procedure to set the LF 8120 s to the factory defaults 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu SET DEFAULTS will be displayed 4 Press SELECT to set parameters to the factory defaults 5 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to
39. eric Display Displays operating configuration and test status messages LOAD MENU Switch In operating mode the LOAD MENU switch controls the loading and unloading of media cartridges In Configuration mode the LOAD MENU switch steps through the menu of configurable parameters TEST SELECT Switch In operating mode the TEST SELECT switch invokes the diagnostic self test In Configuration mode the TEST SELECT switch scrolls through the options available for each configurable parameter WRITE PROTECT The WRITE PROTECT indicator illuminates when either the Write Protect WRT Indicator PROT configuration option is enabled or a media cartridge WRITE PROTECT switch is locked write disabled The WRITE PROTECT indicator will flash when an RTPM condition occurs Also the WRITE PROTECT indicator will flash when the drive or the media is in a read only condition 97664106 A Page 39 POWER ON PROCEDURE The LF 8120 is powered on with the AC Power Switch located on the rear panel The ON position is indicated by a 1 and the OFF position is indicated by a as illustrated below LF 8120 SKIN NOT SHOWN AC POWER OFF 0 AC POWER ON Figure 17 LF 8120 AC Power Switch Positions Perform the following procedure to power on the LF 8120 1 Ensure that the LF 8120 is properly connected see SCSI Bus Considerations sections 2 Refer to the Media Insertion and Removal section and insert a cartridge into slo
40. fer to the next three sections for power cord installation and SCSI cable installation for a single device The LF 8120 has two SCSI input output I O connectors on the rear panel that are used to interface the drive with other SCSI devices see figure below Either SCSI connector can be used as the input or output port because the internal controller cable connection is common to both connectors LF 8120 SKIN NOT SHOWN SCSI CONNECTORS AC POWER CABLE ET AC POWER SWITCH Figure 13 Rear Panel of the LF 8120 Showing SCSI Connectors AC Power CONNECTING THE POWER CORD To install the power cord on an LF 8120 1 Ensure that an AC power cord is available and ready for installation The type of AC power cord being installed depends upon the installation location 2 Ensure facility power is available and the AC power cord connector male end will match the site AC power wall outlet 3 Ensure that the AC power switch on the LF 8120 rear panel is set to the OFF O position 4 Plug the AC power cord connector female end into the AC power receptacle on the LF 8120 rear panel 5 Plug the AC power cord connector into a wall outlet 97664106 A Page 35 CONNECTING MULTIPLE DEVICES To install SCSI interface cables for a multiple device configuration 1 Ensure that the SCSI interface cables and a terminator if required are available and ready for installation 2 Plug one end of a SCSI
41. ge 24 OUTER CARTON LID OPTION ACCESSORIES gt TRAY OUTER CARTON gt gt FOAM CUSHION FOAM INSERT LOCATED BETWEEN SHUTTLE AND P gt DRIVE FRAME Figure 8 LF 8120 Rack Mount Packing 97664106 A Page 25 INSPECTING THE LF 8120 The following items should be included in the LF 8120 carton one LF 8120 with Bezel assembly Tower comes completely assembled one AC power cable one User Manual one combination manual baseplate door lock release tool I O cables optional terminators optional The following optional items if ordered will have been shipped with the LF 8120 in separate cartons LM 8000 Media Cartridges Rack Mount Installation Kit Blank Panel Kit After unpacking the LF 8120 check for damage to the chassis cover chassis and bezel damage to connectors dislocated or broken controls and indicators Report all discrepancies missing items and damaged equipment to your supplier If condensation exists on the drive allow the moisture to evaporate by exposing the LF 8120 to the operating environment for at least 6 hours before powering on the unit REPACKING THE LF 8120 The LF 8120 should be repacked using the original packing materials Prior to packaging the LF 8120 close the baseplates as described in the next section Repack the LF 8120 using the following procedure PLASMON LMS LF 8120 USER MANUAL Page 26 CAUTION Shipping the LF 8120 without closing the baseplates may re
42. genden Verfahren PLASMON L MS LF 8120 USER MANUAL Page 84 VORSICHT Die Grundplatten der Laufwerke m ssen sich in geschlossener Stellung befinden bevor der LF 8120 transportiert wird Nur so kann eine nicht unter den Garantieschutz fallende Besch digung der Laufwerke vermieden werden WARNUNG Der LF 8120 darf nicht ohne geeignete Hilfsvorrichtungen angehoben werden WARNUNG Um Personenverletzungen zu vermeiden sind zwei Personen erforderlich um den LF 8120 auf einer Rampe nach oben zu rollen Hierbei ist sicherzustellen daB die Einheit um nicht mehr als 10 Grad gekippt wird Der LF 8120 wiegt ber 181 kg Wenn die Einheit um mehr als 10 Grad gekippt wird kann sie unversehens umfallen und zu Personenverletzungen f hren INSTALLATIONSANFORDERUNGEN VORSICHT Vor dem Einschalten der Laufwerke des LF 8120 m ssen die Transportbl cke aus Schaumstoff aus den Wagenvorrichtungen entfernt werden 97664106 A Page 85 Wenn der LF 8120 in ein Gerategestell oder Gehause eingebaut ist stellen Sie sicher daB die interne Temperatur des Gestells oder Geh uses die in der Produktspezifikation und dem vorliegenden Handbuch angegebenen Betriebsgrenzen nicht berschreiten Senkrecht gestapelte Einheiten erfordern spezielle Aufmerksamkeit im oberen Bereich in dem h here Temperaturen herrschen Sie m ssen das LF 8120 an eine Stromversorgung anschlie en die eine direkte Erdung hat Netzwerk Erdungsverbindung TT Termina
43. he drive may be turned on or off When the desired state on or off is displayed press the MENU switch to enter that state for parity checking and select the next option in the Set Configuration menu Press the SELECT switch to scroll through the language options Eng English Frh French Grm German for the DOC operating messages When the desired language option is displayed press the MENU switch to enter that option and select the next option in the Set Configuration menu Press the SELECT switch to turn write protect on or off When the desired state on or off is displayed press the MENU switch to enter that state for write protect and select the next option in the Set Configuration menu Press the SELECT switch to scroll through the Auto Load options The drive can be configured to load the cartridge residing in a specific slot 0 12 or the Most Recently Used MRU cartridge When the desired option is displayed press the MENU switch to enable that option and select the next option in the Set Configuration menu Press the SELECT switch to enable or disable the LOAD switch on the DOC When the desired state on or off is displayed press the MENU switch to enter that state for load switch and select the next option in the Set Configuration menu Press the SELECT switch to turn read ahead on or off When the desired state on or off is displayed press the MENU switch to enter that state for read ahead and select the next optio
44. he power plugs from their site power receptacles In situations where disconnecting the plugs is not possible or practical disconnect the system main power to isolate the units from the main power Use of controls or adjustments or performance of procedures other than those specified herein may result in exposure to hazardous laser radiation Do not stare directly into the laser beam or its reflection on any reflecting mirror like surface Invisible laser radiation can be emitted if the unit is open and safety interlocks are defeated TOWER INSTALLATION The LF 8120 Tower configuration is shipped as a complete assembly ready for cable connections and power up No tools are required for the installation CAUTION Remove the foam shipping block from the shuttle assembly before powering on the LF 8120 To install the Tower configuration 1 Connect the AC power cord as explained in the Connecting the Power Cord section Refer to the Installation and De installation section for information regarding the AC ground 2 Connect the host interface SCSI cables and appropriate signal terminators if required as explained in the Installation and de installation section PLASMON L MS LF 8120 USER MANUAL Page 32 SCSI BUS CONSIDERATIONS The length of the SCSI interface cables used to interconnect the LF 8120 with other SCSI devices is dictated by the type of SCSI controller installed in each LF 8120 A maximum of seven LF 8120 s can be
45. host system MODES OF OPERATION The LF 8120 has three modes of operation that are selectable from the DOC Operating Mode Configuration Mode Test Mode In Operating mode the host system can read and write data and select and load media cartridges In Configuration mode an operator can view a menu of parameters and select options for each parameter Test mode invokes drive diagnostics to verify proper drive operation OPERATING MODE The LF 8120 enters the Operating mode after being powered on and displays the Ready message on the DOC The DOC will display the appropriate messages listed in the next table during normal operation To enter Operating mode if the drive is in Test mode wait until the tests are completed and then press the LOAD MENU switch To enter Operating mode if the drive is in Configuration mode press the LOAD MENU and the TEST SELECT switches simultaneously 97664106 A Page 41 The pound symbol shown in the table below designates the number NOTE Table 8 LF 8120 DOC Operating Mode Messages slot orenaTive conpmon POSDISRLAV DOCDGRLAV Doc Inserting Cartridge Inserting Insere Einf gend Loading Media Loading Charger Ladend Drive Ready Cartridge not Locked Ready Pr t Bereit Drive Ready Cartridge Locked Locked Verrouill Gesperrt Drive Reading Cartridge Reading Lecture Lesend Drive Writing
46. in the Drive Characteristics section of this manual two fuses and two spare fuses are integrated into the power receptacle on the rear panel of the LF 8120 refer to the figure below If the drive will not power up one or both of the fuses may have blown To replace blown fuse with spare fuse 1 Set the drive s AC power switch to the OFF position and remove the AC power cord 2 Insert small flat blade screwdriver between the fuse holder and the receptacle housing as shown 3 Gently pry the fuse holder open Slide the fuse holder out of the receptacle and visually inspect the active fuse to determine if it is blown If the active fuse is blown proceed to step 4 otherwise proceed to 5 4 Remove the active fuse and discard it Remove the spare fuse from its storage location and insert the fuse between the fuse housing and the retaining clip 5 Re install the fuse holder into the receptacle sliding the holder into the receptacle until the holder is aligned flush with the receptacle housing 6 Apply power to the unit refer to the Power On Procedure 7 If power is not restored check the other fuse PLASMON LMS LF 8120 USER MANUAL Page 78 RETAINING CLIP ACTIVE FUSE SPARE FUSE IN STORAGE LOCATION FUSE HOLDERS FUSE HOUSING AC POWER RECEPTACLE EP006079 Figure 36 Removing Fuse from AC Power Receptacle Rear View of LF 8120 WARNING If a spare fuse blows immedi
47. interface cable into the vacant SCSI interface connector on the previous device in the SCSI chain see figure below Plug the other end of the cable into a SCSI connector 3 If the LF 8120 is not the last unit in the daisy chain plug one end of the other cable into the vacant connector on the LF 8120 and then connect the other end of the cable to the next SCSI device Repeat this process until you reach the last SCSI device in the daisy chain 4 If the LF 8120 is the last unit in the daisy chain install a terminator on the LF 8120 s vacant SCSI connector 5 Ensure that the SCSI bus is also terminated at the host adapter end 6 The SCSI bus must be terminated at both ends in accordance with the LD 8100 LF 8120 LF 8600 LF 8602 SCSI Interface Specification P N 97662164 FROM LAST SCSI DEVICE LF 8120 SKIN NOT SHOWN OUT TO NEXT SCSI DEVICE Figure 14 Multiple LF 8120 SCSI Interface Cable Connections PLASMON LMS LF 8120 USER MANUAL Page 36 CONNECTING A SINGLE DEVICE To install a SCSI interface cable for a single device configuration 1 Plug one end of the SCSI interface cable into the vacant SCSI interface connector on the host see figure below 2 Plug the other end of the interface cable into a SCSI I O connector on the LF 8120 rear panel INPUT FROM HOST LF 8120 SKIN ia NOT SHOWN 3 TERMINATOR Figure 15 Single LF 8120 SCSI Interface Cable and Terminator Connection 3 Install a termina
48. is displayed on the DOC To enter the Configuration mode 1 Press both the LOAD MENU and TEST SELECT switches simultaneously 2 Verify that View Config is displayed 97664106 A Page 43 Entry to Configuration mode starts with a Main menu allowing the user to select one of four submenus The Main menu includes the following submenu options View Config This is the entry point into the Configuration menu Press the SELECT switch to enter a submenu allowing the user to view the drive operating parameters firmware revisions and hardware serial numbers Press the MENU switch to select the next option in the Main menu Set Config Press the SELECT switch to enter a submenu allowing the user to select and set the drive operating parameters Press the MENU switch to select the next option in the Main menu Diagnostics Press the SELECT switch to enter a submenu allowing the user to display diagnostic parameters or perform diagnostic operations Diagnostics includes the Park Drive option to prepare the drive for shipping Press the MENU switch to select the next option in the Main menu Set Serial Press the SELECT switch to enter the Set Serial submenu thereby allowing the user to set the right digit of the serial number Press MENU to advance to the next digit in the serial number Press SELECT to change the value of each digit NOTE The serial number set in the drive must correspond to the last 5 digits of the drive s actual
49. ive s actual serial number for accurate internal event logging to occur The drive s actual serial number is located on the back of the drive enclosure To change the drive s 5 digit serial number follow these steps 1 Enter the Configuration mode by simultaneously pressing the LOAD MENU and TEST SELECT switches 2 Press the MENU switch until Set Serial is displayed 3 Press the SELECT switch to enter the serial number mode The serial number will be displayed 4 If the serial number does not require revision simultaneously press the LOAD MENU and TEST SELECT switches to move up to the Main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode If the serial number requires revision press the MENU switch until the digit position to be changed is blinking Then press the SELECT switch until the desired digit value is displayed Continue to select digit positions and values until the correct serial number is displayed 5 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the Main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode A structure diagram for the Set Serial menu is shown in the next figure 97664106 A Page 63 PRESS BOTH SWITCHES SIMULTANEOUSLY FROM THE SET SERIAL MENU TO RETURN TO THE MAIN MENU SET CONFIG MENU PRESS BOTH SWITCHES SIMULTANEOUSLY AFTER SETTING A DIGIT TO RETURN TO T
50. le value see the next table for the test value and test name Table 10 Diagnostics Selftests TEST DESCRIPTION OF TEST 0 Power on self test This test cannot be disabled it runs automatically when the drive is powered on PCA Self tests DPR Communication Read Write Data Path OMA Cartridge Guide Sensors Shuttle Baseplate and Spindle Motor Operation Servo Control Systems Read Performance Reserved o N DI A DR Write Power Calibration Press the SELECT switch to select the number of times the test s is to be performed Use the MENU switch cycle through all four digits Press the MENU switch to select the next option in the Diagnostics Menu Press the SELECT switch to view the RTPM Real Time Performance Monitor status If no RTPM error has occurred the DOC will display No RTPM Err If an RTPM error has occurred the DOC will display the media serial number and drive channel combination which caused the RTPM error The media serial number will be displayed for 5 sec S N and then the drive channel will be displayed for 4 sec Channel A B or A B The display will then return to the View RTPM option 97664106 A Page 59 Clear RTPM CAUTION RTPM errors indicate the drive or media require maintenance and place the drive in a read only mode Corrective action may be as simple as cleaning the media that caused the error or may
51. ll show the message which appeared prior to the drive entering the Configuration mode SELECTIONS PRESS BOTH SWITCHES SIMULTANEOUSLY FROM VIEW CONFIG TO RETURN TO THE MAIN MENU View FW Revs SELECT gt DISPLAY FW REVISIONS VIEW CONFIG MENU DISPLAY HW SERIAL NUMBERS PRESS BOTH SWITCHES SIMULTANEOUSLY FROM ANY MENU TO RETURN TO VIEW CONFIG DISPLAY HW PART NUMBERS Figure 19 View Config Menu SETTING THE CONFIGURATION OF THE OPERATING PARAMETERS SET CONFIG To enter the mode to set the drive configuration press the TEST SELECT switch while Set Config is displayed in the Main menu The drive will enter the Set Configuration menu which includes the following options 97664106 A Page 47 Set Defaults SCSI ID Parity Language Wrt Prot AutoLoad Load SW Rd Ahead CDE Curs Busy ModSelRA MMSpinUp Negotiation Press the SELECT switch to set all drive operating parameters to the factory defaults Press the MENU switch to select the next option in the Set Configuration menu Press the SELECT switch to scroll through the possible SCSI ID values 0 through 15 When the desired ID value is displayed press the MENU switch to enter that value as the SCSI ID and select the next option in the Set Configuration menu Press the SELECT switch to turn parity checking on or off SCSI bus parity generation is always enabled but SCSI bus parity checking by t
52. loading Perform the following procedure to enable or disable the LOAD MENU switch 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until Load SW is displayed 5 Press the SELECT switch to scroll through the states for the load switch on off When the desired state is displayed press MENU to enter the state and move to the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the Main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode SETTING THE READ AHEAD OPTION The read ahead option often improves the overall read data transfer rate of the LF 8120 in applications which require continuous blocks of data to be read as compared to the same subsystem without read ahead Perform the following procedure to turn read ahead on or off 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until Rd Ahead is displayed 5 Press the SELECT switch to scroll through the states for read ahead off on When the desi
53. mputer System Interface SCSI via standard SCSI 2 micro connectors located on the rear panel Single ended and differential interface options are available and the interface can be changed in the field Both the single ended and differential controllers support asynchronous or synchronous data transfer operations Preventive maintenance for the LF 8120 is minimal refer to Operator Maintenance section of this manual Corrective maintenance is simplified by internal diagnostic firmware which detects isolates and reports malfunctions to the operator and identifies the Field Replaceable Unit FRU LM 8000 media is interchangeable between the LD 8100 LF 8120 LF 8600 and the LF 8602 The LF 8120 can also read LM 6000 and LM 4000 media Contact Plasmon LMS for availability and ordering information for the LM 4000 media option PLASMON LMS LF 8120 USER MANUAL Page 12 DRIVE CHARACTERISTICS The LF 8120 Rack Mount and Tower configurations use the same major assemblies refer to the next two figures 75 75 CM 29 75 IN ka LF 8120 RACK MOUNT EGEN CONFIGURATION 17 75 IN 2 54 CM a poer 1 0 IN 2223 45 10 CN 4 v 4510 CN 17 75 75 75 cm 2975 gt ILLI 2 LF 8120 TOWER EE 58 42 CM CONFIGURATION YT E Figure 2 LF 8120 Dimensional Details 97664106 A Page 13 li FRONT
54. n If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures reorient the receiving antenna relocate the equipment away from the receiver plug the equipment into a different outlet so that equipment and receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions A pamphlet by the FCC How to Identify and Resolve Radio TV Interference Problems is available from the US Government Printing Office Washington D C 20402 Stock No 044 000 00345 4 CDRH COMPLIANCE LF 8120 contains a Class 1 Laser Product This product complies with 21CFR Chapter 1 Subchapter J applicable at date of manufacture CANADIAN EMI COMPLIANCE Canadian Department of Communications standards require that the following statement appear in operating manuals for any digital apparatus imported into Canada This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications FRENCH TRANSLATION Cet quipement digital ne d passe pas les limites de la Classe A pour les interf rences radio lectriques des syst mes digitaux fix es par les R glements concernant les Interf re
55. n in the Set Configuration menu Press the SELECT switch to turn the CDE indicator a blinking solid cursor in the rightmost display position on or off When the desired state on or off is displayed press the MENU switch to enter that state for CDE Curs and select the next option in the Set Configuration Menu Press the SELECT switch to toggle the Busy option between On and Off When the desired mode has been selected press the LOAD MENU switch to select the next option Press the SELECT switch to toggle the Mode Select Read Ahead option between On and Off When the desired mode has been selected press the LOAD MENU switch to select the next option Press the SELECT switch to toggle the Media Management Spin Up option between On and Off When the desired mode has been selected press the LOAD MENU switch to select the next option Press SELECT switch to toggle between TargSDTR OFF or ON Press MENU to switch to TargSWTR Press SELECT again to toggle between TargSWTR OFF and ON When the desired selections have been made press MENU and SELECT simultaneously to return to the NEGOTIATIONS menu PLASMON LMS LF 8120 USER MANUAL Page 48 A structure diagram for the Set Configuration menu is shown in the next figure To move up a level in the configuration menu hierarchy to the Main menu press the LOAD MENU and TEST SELECT switches simultaneously To exit the Configuration mode press the LOAD MENU and TEST SELECT switches simultan
56. nces Radio lectriques tablis par le Minist re des Communications du Canada All Plasmon LMS products comply with the requirements of this standard Agency Compliance and Approval For details on Agency Compliance and Approval refer to the LF 8100 LF 8120 LF 8600 LF 8602 Product Specification Manual TABLE OF CONTENTS SCOPE 9 RELATED PUBLICATIONS 9 NOTICES 9 GENERAL DESCRIPTION 11 DRIVE CHARACTERISTICS 13 FRONT PANEL 14 REAR PANEL 14 DIMENSIONS AND WEIGHT 15 SHIPPING WEIGHT 15 TEMPERATURE HUMIDITY AND ALTITUDE 16 MEDIA ENVIRONMENTAL CHARACTERISTICS 17 SHOCK AND VIBRATION 17 AC POWER REQUIREMENTS 18 AC GROUND 18 AC POWER CORD 18 POWER SUPPLY PROTECTION FEATURES 18 TILT RANGE 19 HEAT DISSIPATION 19 PARTICULATE LIMITS 19 WARNING LABELS 19 UNPACKING AND REPACKING INSTRUCTIONS 21 UNPACKING THE TOWER CONFIGURATION 21 UNPACKING THE RACK MOUNT CONFIGURATION 24 INSPECTING THE LF 8120 26 REPACKING THE LF 8120 26 CLOSING THE BASEPLATES 27 REPACKING THE TOWER CONFIGURATION 28 REPACKING THE RACK MOUNT CONFIGURATION 29 INSTALLATION AND DE INSTALLATION 31 INSTALLATION REQUIREMENTS 31 TOWER INSTALLATION 32 SCSI BUS CONSIDERATIONS 33 CONNECTING POWER AND SCSI CABLES 35 CONNECTING THE POWER CORD 35 CONNECTING MULTIPLE DEVICES 36 CONNECTING A SINGLE DEVICE 37 CONNECTOR VERIFICATION 38 OPERATING INSTRUCTIONS CONTROLS AND INDICATORS POWER ON PROCEDURE MODES OF OPERATION OPERATING MODE CONFIGURATION MODE VIEWING DIAGNOST
57. nel of the LF 8120 Place the ESD protective packing material on top of the drive Place the two end cushions which hold the accessories box on the top front and rear of the LF 8120 Place the power and interface cables User Manual and other accessories into the options and accessories box and seal with tape Place this box between the top end cushions Slip the corrugated shipping carton over the LF 8120 and the raised ramp and lower the carton down to the top of the pallet Strap the carton to the pallet at each end PLASMON LMS LF 8120 USER MANUAL Page 28 REPACKING THE RACK MOUNT CONFIGURATION 1 Open the media access door and manually move the shuttle all the way to the left and insert the foam shipping block to hold it in place Close the media access door 2 Remove the LF 8120 chassis with its bezel from the Rack Mount configuration by reversing the procedure detailed in the Installation and De installation section The bezel extends below the chassis ensure that you do not place the unit flat a hard surface thereby damaging the bezel 3 Ensure that the lower packing material is positioned to form a rectangular frame for the LF 8120 chassis which opens to the front 4 Place the bezel relief cushion on the pallet so that it will support the chassis just behind the bezel MANUALLY MOVE THE SHUTTLE TO THE LEFT INTO THE SHIPPNG POSITION
58. ng 40 Wenn sich das Laufwerk nicht einschalten l t k nnte eine oder beide Sicherungen durchgebrannt sein So tauschen Sie eine durchgebrannte Sicherung gegen eine Ersatzsicherung aus 1 gt O Stellen Sie den Wechselstromschalter des Laufwerks auf AUS 0 und ziehen Sie das Netzkabel ab F gen Sie einen kleinen Flachschraubenzieher zwischen dem Sicherungshalter und dem Geh use der Buchse ein vgl Abbildung 40 ffnen Sie den Sicherungshalter vorsichtig Ziehen Sie den Sicherungshalter aus der Buchse heraus und berpr fen Sie die aktive Sicherung um festzustellen ob sie durchgebrannt ist Wenn die Sicherung durchgebrannt ist fahren Sie mit Schritt 4 fort ansonsten mit Schritt 5 Entfernen Sie die aktive Sicherung und entsorgen Sie sie Nehmen Sie die Ersatzsicherung aus deren Aufbewahrungsort und f gen Sie die Sicherung zwischen dem Sicherungsgehause und der Halteklammer ein Installieren Sie den Sicherungshalter wieder in der Buchse schieben Sie dabei den Halter in die Buchse bis der Halter b ndig auf das Gehause der Buchse ausgerichtet ist Wenn die Stromversorgung nicht wiederhergestellt wird pr fen Sie die andere Sicherung PLASMON LMS LF 8120 USER MANUAL Page 90 WARNUNG Sollte eine Ersatzsicherung unmittelbar nach dem Ersetzen der Originalsicherung entfallen d rfen Sie diese Sicherung nicht mehr ersetzen Wenden Sie sich an die n chste Stufe technische
59. onfig is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until CDE Curs is displayed 5 Press the SELECT switch to scroll through the states for CDE Curs off on When the desired state is displayed press MENU to enter the state and move to the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode 97664106 A Page 55 SETTING THE BUSY OPTION When enabled the Busy message is displayed at the DOC during a spin up or spin down operation Enabling this option will cause the Drive to respond to a Start command via SCSI or MCLI with a BUSY message over SCSI Perform the following procedure to enable or disable the BUSY option 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until Busy is displayed 5 Press the SELECT switch to scroll through the states for the load switch on off When the desired state is displayed press MENU to enter the state and move to the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the main
60. ose which media cartridge is automatically inserted and loaded at power up and whenever the LOAD MENU switch is pressed while in the Operating mode The factory default selects the cartridge in slot 1 The options are 1 12 or Most Recently Used MRU Perform the following procedure to set the LF 8120 s AutoSpin option 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set Config is displayed 3 Press the SELECT switch to enter the Set Configuration menu 4 Press the MENU switch until AutoLoad is displayed 5 Press the SELECT switch to scroll through the Auto Load options The drive can be configured to load the cartridge residing in specific slot 0 12 or the Most Recently Used MRU cartridge When the desired option is displayed press the MENU switch to enable that option and select the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the Main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode 97664106 Page 53 SETTING THE LOAD SWITCH OPTION The load switch option enables the user to enable or disable the LOAD MENU switch on the DOC The LOAD MENU switch can be disabled to prevent accidentally spinning down a media cartridge This also prevents cartridge loading from the DOC giving the host exclusive control of media
61. ot allow the cutting blade to penetrate into the carton 3 Carefully lift the outer corrugated carton up and remove it while supporting the inner hinged wooden ramp When the carton is removed lower the ramp to the floor and remove the front foam cushion 4 Remove the accessories box inner carton containing cables and documentation and the two foam cushions which support the box Remove the ESD protective packing material 97664106 A Page 21 OUTER CARTON LID gt ESN e OPTIONS ACCESSORIES OUTER CARTON gt e 4 TOP FOAM EL CUSION i FOAM FOAM INSERT LOCATED CUSHION BETWEEN SHUTTLE AND gt gt FRAME OF THE DRIVE Figure 5 LF 8120 Tower Packing PLASMON L MS LF 8120 USER MANUAL Page 22 5 Ensure that the casters are locked Lift the front end of the LF 8120 high enough to remove the pallet cushion and then lower the LF 8120 onto its casters 6 Unlock the casters and roll the LF 8120 down the ramp to its installation location Precautions should be taken to avoid sudden bumps and jarring 7 Lock the casters once you have the LF 8120 situated at its installation location UNLOCKED LOCKED Figure 6 Caster for the LF 8120 Tower 8 Open the media access door and remove the foam insert Manually move shuttle all the way to the right to the home position MANUALLY MOVE SHUTTLE TO THE RIGHT TO REMOVE THE FOAM INSERT
62. perating limits as stated in the Product Specification and this document When vertically stacked these units require special attention at the top area where higher temperatures exist The LF 8120 must be connected to a power distribution system that has a direct connection to earth ground Terminated Terra TT network ground connected This unit is not suitable for use on a floating ground Interrupted Terra IT network Ensure the drive is connected to a power distribution system with adequate current handling capacity The following table lists the clearances required to provide proper cooling air circulation adequate access for cartridge loading and unloading and full rack extension Table 6 Operational Clearances for LF 8120 Configurations AREA RACK MOUNT TOWER Front 132 cm 52 in 51 cm 20 in Rear 51 cm 20 in 51 cm 20 in Sides 12 7 cm 5 in 97664106 A Page 31 Ensure that the site selected for the LF 8120 Tower or Rack Mount configuration is able to support volumetric air flow of 0 77 m min 27 cfm For the Rack Mount configuration the back door of the enclosing equipment cabinet must have air vents Ensure that the operating environment is free from dust WARNING To prevent fire or shock hazard do not expose the LF 8120 to rain or moisture Refer servicing to qualified technicians In case of fire or other emergency isolate the units from the main power by disconnecting t
63. r Unterst tzung Dies k nnte das Symptom eines schwerwiegenderen Problems sein das entweder am Netzteil des Laufwerks oder in der Stromversorgung liegt 97664106 A Page 91 RE Storing More Of Your DD Plasmon Digital World Permanently
64. rarchy to the Main menu press the LOAD MENU and TEST SELECT switches simultaneously To exit the Configuration mode press the LOAD MENU and TEST SELECT switches simultaneously from the Main menu The display will show the message which appeared prior to the drive entering the Configuration mode PLASMON LMS LF 8120 USER MANUAL Page 60 Enter Sensor Display Mode PRESS BOTH SWITCHES SIMULTANEOUSLY FROM SET CONFIG TO RETURN TO THE MAIN MENU SET CONFIG MENU PRESS BOTH SWITCHES SIMULTANEOUSLY FROM ANY MENU TO RETURN TO SET CONFIG FROM LAST MENU SELECTION 19 2Kb 38 4Kb 57 6Kb 115 2Kb a SIMULTANEOUSLY Figure 22 Diagnostics Menu Part 1 97664106 A Page 61 PRESS BOTH SWITCHES SIMULTANEOUSLY FROM SET CONFIG TO RETURN TO THE MAIN MENU Display RTPM View RTPM SET CONFIG MENU PRESS BOTH SWITCHES SIMULTANEOUSLY FROM ANY MENU TO RETURN TO SET CONFIG To top of Menu WPC Options d ENUCSELECT SWITCHES SIMULTANEOUSLY Figure 23 Diagnostic Menu Part 2 PLASMON LMS LF 8120 USER MANUAL Page 62 SET THE INTERNAL DRIVE SERIAL NUMBER SET SERIAL To enter the serial number submenu press the TEST SELECT switch while Set Serial is displayed in the Main menu The drive will enter the menu allowing the operator to view and change the internal drive serial number NOTE The serial number set in the drive must correspond to the last 5 digits of the dr
65. rdnungsgem es Funktionieren der Sicherheitsmerkmale dieses Ger tes zu gew hrleisten d rfen Wartungsarbeiten nur von qualifiziertem Fachpersonal ausgef hrt werden Es sind dar ber hinaus nur Ersatzteile zu verwenden die von der Firma Plasmon LMS angegeben werden Im Falle eines Feuers oder in einem anderen Notfall sind die Ger te vom Hauptnetz zu trennen indem die Netzstecker aus den Steckdosen am Einbauort gezogen werden Ist ein Herausziehen der Stecker nicht m glich oder zu umst ndlich trennen Sie die Ger te mit Hilfe des System Hauptnetzabschalters vom Hauptnetz Um Feuer oder Stromschlaggefahr zu vermeiden ist dieses Ger t niemals Regen oder Feuchtigkeit auszusetzen Wartungsarbeiten sind qualifiziertem technischen Personal zu berlassen RADIO TV INTERFERENCE USA The information in this section applies only to units in use within the United States This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instruction may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class A computing device in accordance with the specifications of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installatio
66. red state is displayed press MENU to enter the state and move to the next option in the Set Configuration menu 6 Simultaneously press the LOAD MENU and TEST SELECT switches to move up to the Main menu Simultaneously press the LOAD MENU and TEST SELECT switches again to exit Configuration mode PLASMON LMS LF 8120 USER MANUAL Page 54 CAUTION The read ahead option is system dependent Ensure that you check with your system analyst before setting this option When enabled the read ahead option uses the data buffer 12 8 MBytes to store data sectors read from the disk beyond those sectors requested by the host Subsequent sequential sectors will be read directly from the buffer instead of incurring the latency time it takes to access sequential sectors Refer to the LD 8100 LF 8120 LF 8600 LF 8602 SCSI Interface Specification P N 97662164 SETTING THE CDE CURS OPTION The CDE Curs Controller Detected Error option enables a blinking solid cursor in the rightmost character location of the DOC panel when a CDE has occurred In most system installations the host system will recover from reported CDE s and no user intervention is required A developer may wish to enable this indicator during system development or installation Perform the following procedure to turn CDE Curs on or off 1 Enter the Configuration mode by pressing both the LOAD MENU and TEST SELECT switches simultaneously 2 Press the MENU switch until Set C
67. s maximum in Plasmon LMS packaging No condensation is permitted Transit specifi 2 Maximum operating temperature is 42 _C for a free standing drive at sea level unless otherwise stated Maximum operating 3 See the LD 8100 LF 8120 LF 8600 LF 8602 Product Specification P N 97663035 for more information concerning the tem MEDIA ENVIRONMENTAL CHARACTERISTICS The following table presents the LM 8000 Media environmental characteristics If the media temperature is more than 10 C 50 F different from the ambient temperature of the Drive then the media should be acclimated in the Drive environment for at least 30 minutes before writing to the media Reading from the media may be done immediately Table 3 Media Operation Storage and Transportation Environments 50 F to 116 6 F OPERATION AND SHORT TERM TRANSPORTATION LONG TERM STORAGE 2 weeks maximum STORAGE 2 years maximum Temperature 10 to 47 C 20 C to 55 C 10 to 30 C 4 0 F to 131 0 F 50 F to 86 0 F Relative Humidity 5 80 5 90 5 80 no condensation Wet Bulb Temperature 26 C max 78 8 F 26 C max 78 8 F 26 C max 78 8 F Temperature Gradient 10 C hr max 31 C hr 5 C hr max 18 0 F hr max 55 8 F hr max 9 0 F hr max Air Pressure N A N A N A Solar Radiation N A Case to be kept closed Not to be stored in direct sunlight The following table lists
68. serial number for accurate internal event logging to occur The drive s actual serial number is written on the back of the drive enclosure A structure diagram for the Main menu is shown in the next figure To move up a level in the Configuration menu hierarchy press the LOAD MENU and TEST SELECT switches simultaneously To exit the Configuration mode press the LOAD MENU and TEST SELECT switches simultaneously from the Main menu The display will show the message which appeared prior to the drive entering the Configuration mode The Ready message is displayed when a media cartridge is loaded on the drive spindle PLASMON LMS LF 8120 USER MANUAL Page 44 ENTER VIEW View Config CONFIG MENU PRESS BOTH SWITCHES SIMULTANEOUSLY FROM ANY MENU TO RETURN TO THE MAIN MENU ENTER SET CONFIG MENU ENTER DIAGNOSTIC MENU ENTER SERIAL NUMBER ENTRY MENU Set Serial Figure 18 Main Menu 97664106 A Page 45 VIEWING THE CONFIGURATION VIEW CONFIG To view the configuration press the TEST SELECT switch while View Config is displayed in the Main menu The drive will enter the View Configuration menu which includes the following options View Current View FW Revs View HW S Ns View HW P Ns Press the SELECT switch to display the current drive operating parameters The operating parameters are listed in the table below Press the MENU switch to select the next option in the View Configuration m
69. sgem abgeschlossen ist PLASMON L MS LF 8120 USER MANUAL Page 86 VORSICHT Vor dem Einschalten der Laufwerke ist sicherzustellen daB die Transportbl cke aus Schaumstoff aus den Wagenvorrichtungen entfernt wurden Anweisungen zum Einschalten des Systems finden Sie in Abschnitt 5 des vorliegenden Handbuchs WARNUNG Setzen Sie die Verriegelung des LF 8120 nicht auBer Kraft und ffnen Sie nicht beide Laufwerke gleichzeitig EINSCHALTVERFAHREN HINWEIS Die Seriennummer die dem Laufwerk zugeordnet wird muB mit den letzten 5 Ziffern der tatsachlichen Seriennummer des Laufwerks bereinstimmen damit eine exakte interne Ereignisprotokollierung stattfinden kann Die tats chliche Seriennummer des Laufwerks befindet sich an der R ckseite des Laufwerksgeh uses EINSTELLEN DIE DEICE ID HINWEIS Schalten Sie das Laufwerk nach R cksetzung der Ger tekennung aus warten Sie 1 Sekunde und schalten Sie das Laufwerk dann wieder ein Dies stellt sicher da die neue Ger tekennung vom SCSI Bus anerkannt wird EINSTELLEN DIE READ OPTION VORSICHT Die Option Read ahead ist systemabh ngig Setzen Sie sich mit Ihrem Systemanalytiker in Verbindung bevor Sie diese Option einstellen 97664106 A Page 87 ANZEIGEN DER DIAGNOSEERGEBINISSE ODER DURCHFUREN VON DIAGNOSERVER FAHREN VORSICHT Da die Initialisierungsvariablen nicht wiederhergestellt werden k nnen nachdem sie gel scht wurden sollte dieser Vorgang nur von
70. sult in damage to the drive which is not covered under warranty CLOSING THE BASEPLATES 1 Ensure that a cartridge is not inserted in the drive if it is unload the cartridge Remove all cartridges from the shuttle To remove cartridges from a drive that is not operational follow the procedure below 2 Ensure that the AC Power switch is set to the OFF O position 3 At the rear panel insert the manual release tool into the upper access hole and engage the recessed D shaped shaft Turn the tool handle clockwise as far as it will turn closing the upper baseplate 4 Repeat step b at the lower manual release access hole to close the lower baseplate 5 Select the Park Drive option as explained in the Operating Instruction section of this manual LF 8120 SKIN MANUAL RELEASE en NOT SHOWN REAR PANEL LOWER ACCESS HOLE Figure 9 Manually Closing the Drive s Baseplates 97664106 A Page 27 REPACKING THE TOWER CONFIGURATION Open the media access door Manually push the shuttle all the way to the left and insert the foam shipping block to hold it in place Close the media access door Roll the LF 8120 up onto its shipping pallet and lock all four casters to prevent rolling Lift the front and rear of the LF 8120 high enough and place the caster support underneath the drive Raise the wooden ramp to the vertical position and place the pallet cushion between the ramp and the front pa
71. t 1 If slot 1 is empty the LF 8120 will display 1 Empty on the DOC shortly after initial power on NOTE Slot 1 is the factory setting for the media autoload configuration option If this option has been changed by the user all references to slot 1 in this manual apply instead to the slot number selected in the autoload configuration option Refer to the Configuration Mode section for more information on setting configuration options PLASMON LMS LF 8120 USER MANUAL Page 40 3 Set the AC Power Switch to the ON I position and verify that air is flowing through the LF 8120 4 Verify that the WRITE PROTECT indicator is illuminated briefly 5 Verify that the Selftest message is displayed on the DOC The Selftest message indicates that the power on selftests are running When the power on selftests have run without errors the drive will perform a test to determine which slots in the shuttle are occupied by media cartridges and then will load media number 1 When the 1 Ready message is displayed the LF 8120 has passed the power on selftests and has successfully loaded the LM 8000 media cartridge in slot 1 6 Verify that the Selftest message displayed on the DOC is replaced by the 1 Ready message 7 Refer to the Modes of Operation section of this manual to familiarize yourself with the LF 8120 modes of operation The LF 8120 is now in the normal Operating mode and is ready to be controlled and accessed by a
72. ted Terra Diese Einheit ist nicht f r den Einsatz mit einer schwimmenden Erdung Netzwerk IT Interrupted Terra vorgesehen Achten Sie darauf da das Laufwerk an eine Stromversorgung mit ausreichender Stromst rke angeschlossen ist WARNUNG Um Brand oder Elektroschock zu vermeiden darf der LF 8120 weder Regen noch Feuchtigkeit ausgesetzt werden Wartungsarbeiten d rfen nur von qualifizierten Technikern ausgef hrt werden Trennen Sie die Einheiten im Falle eines Brandes oder einer anderen Notsituation von der Hauptstromversorgung indem Sie die Stecker aus den Steckdosen ziehen Sollte das Herausziehen der Stecker nicht m glich oder praktisch sein trennen Sie die Hauptstromversorgung Die betriebsfremde Benutzung von Bedienelementen oder Reglern oder die Durchf hrung von Verfahren die im vorliegenden Handbuch nicht beschrieben sind kann zu einer gef hrlichen Belastung durch Laserstrahlung f hren Vermeiden Sie es direkt in den Laserstrahl oder dessen R ckstrahlung auf einer reflektierenden Oberfl che zu blicken Unsichtbare Laserstrahlung kann freigesetzt werden wenn die Einheit offen ist und die Sicherheitsverriegelungen au er Kraft gesetzt sind ANSCHLUB BERPR FUNG Vor dem Einschalten des Systems sind folgende Schritte durchzuf hren 1 berpr fen Sie ob der Host Adapter falls vorhanden ordnungsgem abgeschlossen ist 2 berpr fen Sie ob der letzte LF 8120 im Bus falls ein Bus vorhanden ordnung
73. the SELECT switch to clear the NvRAM initialization variables in the drive Press the MENU switch to select the next option in the Diagnostics menu Cal Shuttle Press SELECT switch the message Is Shuttle calibration required will be displayed Press SELECT switch again and follow all instructions that are displayed on the DOC After calibration is complete press the SELECT and MENU switch to select the next option in the Diagnostics menu View CDEs Press the SELECT switch to view the controller detected error CDE The DOC will display the error code When no error has occurred the No CDE Error message is displayed The error code is cleared upon exiting the Diagnostics menu The error code should be logged by the operator for aiding the CE in diagnosing the drive problem Press the MENU switch to select the next option in the Diagnostics menu Baud Press the SELECT switch to cycle through the available baud rates When the desired is displayed press MENU to go to the next menu item PLASMON L MS LF 8120 USER MANUAL Page 58 Test Start Test End Test Cycles View RTPM Press the SELECT switch to select the Test to be performed 0 9 Once the desired test has been selected press MENU to select the Test End value see the next table for the test value and test name Press the SELECT switch to select last Test to be performed 0 9 Once the desired test has been selected press MENU to select the Test Cyc
74. tor on the vacant connector of the LF 8120 4 Ensure that the SCSI bus is also terminated at the host adapter end 5 The SCSI bus must be terminated at both ends in accordance with the LD 8100 LF 8120 LF 8600 LF 8602 SCSI Interface Specification P N 97662164 97664106 A Page 37 CONNECTOR VERIFICATION Prior to powering on the system 1 Verify proper termination at the host adapter if applicable 2 Verify proper termination at the last LF 8120 on the bus if applicable CAUTION Ensure that the foam shipping block has been removed from the shuttle assembly before powering on the LF 8120 Refer to the Operating Instruction section in this manual for power on procedures PLASMON LMS LF 8120 USER MANUAL Page 38 OPERATING INSTRUCTIONS CONTROLS AND INDICATORS The Drive Operator Console DOC shown in the figure below is located on the front panel of the LF 8120 The DOC provides the controls and indicators that enable a user to operate the LF 8120 The DOC controls and indicators consist of an alphanumeric display a LOAD MENU switch a TEST SELECT switch and a WRITE PROTECT indicator Refer to the table below for a description of the DOC controls and indicator DISPLAY WRITE PROTECT INDICATOR Q WRITE PROTECT LOAD MENU TEST SELECT SWITCH pp cu SWITCH LOAD MENU TEST SELECT Figure 16 Drive Operator Console Table 7 DOC Controls and Indicators CONTROL INDICATOR PURPOSE FUNCTION Alphanum
75. tore the media cartridge in the drive 4 Remove cartridges from the drive when the drive is going to be moved 5 Apply labels only in designated areas Refer to the Affixing Label section for instructions on label placement 6 Avoid exposing the media cartridge to direct sunlight and condensation CAUTION Careful attention to the environmental constraints specified in the LM 8000 Media Specification P N 97663080 is strongly recommended to prevent damage to the media 7 Do not expose the media cartridge to temperature extremes 8 Stabilize the media cartridge to the specified operating temperature range 1 hr before use 9 Do not open the media access shutter 10 Do not touch the disk surface through the media access shutter 11 Do not remove the disk from the cartridge 12 Use handle and store the media cartridge in clean office conditions 13 Do not smoke while handling the media Smoke is a prime source of disk contamination All smoking materials should be kept away from areas where the media are in use or storage 14 Keep external surfaces of the cartridge clean Dust the cartridge periodically with a soft dry lint free cloth 97664106 A Page 67 SETTING THE WRITE PROTECTION SWITCH To manually write protect a cartridge set the write protect switch on the data cartridge as indicated in the next figure WRITE PROTECT NOT SWITCH WRITE PROTECTED WRITE PROTECTED HOLE IS OPEN WRITE PROTECTED H
76. uch auf den angegebenen Betriebstemperaturbereich stabilisieren 9 Die Zugangsabdeckung des Datentr gers nicht ffnen 10 Die Plattenoberflache nicht durch die Zugangsabdeckung ber hren 11 Die Magnetplatte nicht aus der Kassette herausnehmen 12 Die Datentragerkassetten in einer sauberen B roumgebung benutzen handhaben und lagern 13 W hrend der Handhabung von Datentr gern nicht rauchen Asche und Tabak sind eine Hauptquelle f r die Verunreinigung von Magnetplatten Alle Rauchutensilien sind aus den Bereichen fernzuhalten in denen Datentr ger benutzt oder gelagert werden 14 Die AuBenflachen der Kassetten sauber halten Die Kassetten regelmaBig mit einem weichen trockenen fusselfreien Tuch reinigen Weitere Informationen zur Pflege und Handhabung von Datentr gern finden Sie in der Spezifikation f r den LM 8000 Datentr ger WARNUNG Setzen Sie die Verriegelung des LF 8120 nicht auBer Kraft und ffnen Sie nicht beide Laufwerke gleichzeitig 97664106 A Page 89 VORSICHT Wenn die Geblasefilterelemente nicht sauber gehalten werden kann die Luftzirkulation im Laufwerk beeintrachtigt werden Dies kann zu einem berm igen Temperaturanstieg und damit zu einer Besch digung der Laufwerke f hren AUSWECHSELN VON SICHERUNGEN Wie in Abschnitt 2 6 des vorliegenden Handbuchs dargestellt sind zwei Sicherungen und zwei Ersatzsicherungen in die Netzbuchse an der Ger ter ckseite des LF 8120 eingebaut vgl Abbildu
77. utomated loading and unloading into the optical drive The LF 8120 Auto Loader provides up to 30 GBytes LM 8000 Cartridge of online storage or up to 360 GBytes nearline storage The LF 8120 is available in either a Rack Mount or Tower configuration RACK MOUNT CONFIGURATION TOWER CONFIGURATION L Figure 1 LF 8120 Configurations A Drive Operator Console DOC located on the front panel of the drive provides user control of drive operation and configuration as explained in the Operating Instruction section of this manual Operating messages are presented on the alphanumeric display in English French or German The language used is selectable The front panel includes a lockable media access door to provide operator access to the shuttle and media cartridges 97664106 A Page 11 The Auxiliary Diagnostic Port ADP located on the rear panel of each drive can be used to download updates to the drive firmware in the field Refer to the LD 8100 LF 8120 LF 8600 LF 8602 Product Specification P N 97663035 for more information The LD 8120 supports a maximum sustained read and write transfer rate of 6 0 MBytes sec without data verification The drive will also support a 2 9 MBytes sec write transfer rate with error correction and defect management to maintain data integrity and manage media flaws The LF 8120 implements the Small Co

Download Pdf Manuals

Related Search

Related Contents

Samsung MM-T8 manual de utilizador  SilverFast® 8  APC G35T10KF1B2S Power Supply User Manual  User Manual - Zeta Alarm Systems  Mode d`emploi Royal Swiss Modèle Pegasus Numéro de référence  Luci Creide 取扱説明書  Final Specs Cover 810.psd  Optimus 120-2152 CD Player User Manual  Annonces Février 2011  section 4.2 - Bowltech Danmark A/S  

Copyright © All rights reserved. Failed to retrieve file