English manual — free
Contents
1. 53 Autogood products 130 1 Year Product Warranty Zylux Distribution Pty Ltd warrants to the Customer that this product is substantially free from defects in materials and workmanship under normal use for a period of 1 Year from the Date of Purchase Excl Batteries Please ensure you keep a copy of your receipt on file as this will be required for proof of purchase and to validate your warranty Obtaining Warranty Service Within the warranty period the Customer must contact the authorised supplier retailer where the product was purchased or alternatively you can contact the Zylux Tyredog service centre through one of the following methods Hotline 03 9482 2203 Website www zylux com au If the Authorised Supplier and or Zylux Tyredog service centre concludes that while under normal use a product failure or malfunction occurred during the warranty period and was caused by a defect in material or workmanship see Exclusions the Customer will be asked to ship to the nearest service point The product must be packaged appropriately for safe shioment To prove that the product is under warranty the customer should enclose a copy of their receipt for proof of purchase It is recommended that returned products be sent by registered mail as Zylux Distribution Pty Ltd accepts no responsibility liability for goods lost or damaged in transit Return Shipping costs to be incurred by the Customer Exclusions If2. n c1 c1 c4 c Ear c P 3 Autogood products 130 Autogood products 130 6 SET RELAY ID Relay Code Learning Mode SET RELAY ID RELAY ID In the advanced settings menu highlight SET RELAY and press enter 4 SET THRESHOLD 5 SET CAR TYPE 6 SEI RELAY ID NEXT ESC ENTER The SET RELAY ID screen will display the current car type If the car type uses a single relay only the MUTE button will be functional on screen If the car type uses two relays the TEMP and LIGHT buttons are activated to alternate between the relay locations being learned FRONT or REAR 37 Autogood products 130 SETTING RELAY FRONT TRUCK WH 06 r ores GNE ESC FRONT REAR Once the Relay location is selected press the SYNC button on the Relay you wish to program into that location When the monitor has learned the code from the Relay it will beep and then begin a Relay Call Once the Relay Call is successful the unit will return to the SET RELAY ID screen From here you can either set another relay if applicable or exit to the main menu NOTE A Relay can NOT be stored in both front and rear locations 38 Autogood products 130 7 SET SENSOR ID Replacement Sensor Learning Mode SET RELAY ID ESC escape In the advanced settings menu highlight SET SENSOR and press enter 5 SET CAR TYPE 6 SET RELAY ID
3. If using the included power cord remove the DC socket plug at the bottom of the relay If not using the power cord ensure the socket plug remains fitted as it seals the Relay from water etc When plugging in the DC plug ensure it is plugged in firmly and will not come loose When inserted correctly it will be sealed from water and other elements When using the power cord the supplied bottom cover can be fitted to ensure the plug does not come loose te When fitting the Relay time and care must be taken to properly decide on a mounting location Some key factors that must be considered are e Total distance between first and last sensors e Total distance of car truck car trailer etc e Vehicle trailer structure chassis body density etc Please remember that any metal between the sensors relay monitor will play a part in limiting the signal transmission between Tyredog components Although a metal object may not be in the direct line of sight between the components it may still hinder signal transfer if the object is nearby or offside to the signal transmission path 16 Autogood products 130 When mounting the Relay be sure that it is mounted away from moving parts tail shaft axle etc sources of heat exhaust and is fitted in such a place that would keep it protected from potentially damaging terrain The Relay can be mounted using the supplied heavy duty bracket or on its own using the mounting holes
4. Internet storeof N 2 autogoods 7 23 9 13 COM UA CAR RECEIVERS Receivers M edia receivers and stations Native receivers CD DVD changers FM modulators USB adapters Flash memory Facia plates and adapters Antennas Accessories CAR AUDIO Car audio speakers Amplifiers Subwoofers Processors Crossovers Headphones Accessories TRIP COMPUTERS Universal computers Model computers Accessories GPS NAVIGATORS Portable GPS Built in GPS GPS modules GPS trackers Antennas for GPS navigators Accessories VIDEO DVR TV sets and monitors Car TV tuners Cameras Videomodules Transcoders Car TV antennas Accessories SECURITY SYSTEMS Car alarms Bike alarms M echanical blockers Immobilizers Sensors Accessories OPTIC AND LIGHT Xenon Bixenon Lamps e LED Stroboscopes Optic and Headlights Washers Light rain sensors Accessories PARKTRONICS AND MIRRORS Rear parktronics Front parktronics Combined parktronics Rear view mirrors Accessories HEATING AND COOLING Seat heaters Mirrors heaters Screen wipers heaters Engine heaters Auto refrigerators Air conditioning units Accessories TUNING Vibro isolation Noise isolation Tint films Accessories ACCESSORIES Radar detectors Handsfree Bluetooth Windowlifters Compressors Beeps loudspeakers M easuring inst
5. Battery Cover Back of Monitor Monitor bracket screw Monitor bracket Ball joint adjustment Ball joint Suction cup lock Suction cup Relay The relay is the main link between the sensors and the monitor Without it the system will not function It is recommended the relay be mounted in a central location with considerably even distance between the furthest forward and furthest rearward sensors Sync button LED DC socket Antenna TOP BOTTOM TIP It is important to remember that sensors connect to the relay they are assigned to If the relay is removed from the vehicle the system will not function This is vital in car trailer situations when the trailer is often unhitched from the car The relay should be mounted at the rear of the vehicle in this case to ensure optimum performance 12 Autogood products 130 Tyredog Sensor The sensor has two sections The sensor cap and sensor body Its lightweight design and external application is intended to aid the user to install tyre pressure system at home without any technical knowledge or assistance Battery cover A 0 Valve stem connection 3 way adapter Valve stem connection Sensor Connection valve Security screw thread The 3 way adapter is an optional accessory and must be purchased separately RECCOMMENDED ONLY FOR DEEP DISH OR TRUCK WHEELS 13 Autogood products 130 GUI Layout Signal status T Flashing Waiti
6. SET THRESHOLD NEXT DEC decrease ADD increase the advanced settings menu highlight SET THRESHOLD and press enter 2 CHANGE TRAILER 3 SET UNIT 4 SET THRESHOLD NEXT ESC ENTER The arrow gt symbol will be displayed next to the parameter you wish to change Press TEMP and LIGHT to adjust the selected warning value Below are the available values for each setting Min 5 0 PSI Max 200 0 PSI High Pressure Min 20 0 PSI Max 200 0 PSI High Temperature Min 20 C 110 C 31 Autogood products 130 l o Pressure 100 PSI Hi Pressure 160 P SI Hi Tempera 7O C um um E umm NEXT DEC ADD As settings are being adjusted the corresponding axle set will flash The axles are separated into groups pressing NEXT after adjusting the Hi Temperature warning will advance to the next axle EG c m BG NB zU am 1 4 I k Vi a s A B C If you wish to have the same values for all wheels pressing and holding NEXT will enable the unit to make all adjustments within one setting This mode is indicated by all wheels flashing at once This is a temporary function and must be activated each time you wish to use it All adjustments in this mode are performed the same as each axle individually When pressing NEXT after the last Hi Temp Setting the monitor will ask if you want to save the settings to the Relay Pressi
7. 7 SET SENSOR ID NEXT ESC ENTER This feature is used to program Learnable replacement sensors in the event that one or more of the original sensors are damaged or stolen As with the original Tyredog sensors all learnable sensors are numbered Replacement sensors are designed only to replace originals of the same number IE if your number 2 sensor is damaged it can only be replaced by a number 2 Learnable sensor If the wrong sensor is programmed the original sensor of that location will be permanently deleted from the Relay memory Always be sure to request the correct number sensor 39 Autogood products 130 SETTING TIRE Press the SYNC BUTTON on the Relay you wish to program the sensor s to The L E D will illuminate and the relay location will be displayed on the screen SETTING FRONT TRUCK WH 08 HHI 2 ESC FRONT REAR The L E D will illuminate meaning the Relay is ready to learn the sensor code Insert the supplied CR1632 battery into your new learnable sensor the corresponding tyre icon will flash and the monitor will beep Repeat this step for any additional sensors you may wish to program 40 Autogood products 130 Programming additional sensors The TD 2000A system can be upgraded to monitor more sensors than it was originally supplied with These instructions must be strictly adhered to ensure correct programming of the new senso
8. Exclusive Features TYREDOG powerful tool for maximizing uptime and improving safety TYREDOG sets a new standard in wireless tyre pressure monitoring systems A leading WTPMS solution for the light to heavy duty car and trucking industries TYREDOG Is continuously developing new and better TPMS designs and manufacturing technologies TYREDOG has helped major players in the trucking industry improve safety and reduce operational costs The major feature of TYREDOG TPMS 15 the use of the world s smallest valve cap sensor The extremely lightweight compact sensor has been designed to simplify installation and remove the need to have wheels balanced when fitted Through wireless technology tyre pressure and temperature information 15 displayed on the friendly Graphic User Interface LCD monitor Installation D I Y System can be fitted quickly without any technical knowledge e Wireless All signals are sent via radio frequency with no wires Battery powered Sensors monitor and relay are battery powered Monitor and relay can be operated with supplied power cables Security All kits include the SecureFit locking mechanism meaning your sensors will not come loose unexpectedly e Relay Increases the signal transmission range meaning tyres can be monitored on the largest and most complex vehicles 5 Autogood products 130 Operation e Real time Tyre pressures are updated automatically so there is no need to push bu
9. FRONT TRUCK WHE 10 d 4 ry o gt Insert the supplied batteries into the Learnable Sensors the corresponding tyre icon will flash and the monitor will beep Once all new Sensors are programmed and confirmed press esc to return to the main menu 43 Autogood products 130 ADVANCED FUNCTIONS Initialization PSI 126 126 I 1 ay las 1 zB After powering up the system will run the initial relay call This will take around 10 seconds depending how many relays and sensors are operating The most recent figures will be shown on screen until the unit receives all sensor updates Any change in pressure or temperature will force that sensor to send an update If there is no change or the monitor is turned on after a change occurs sensors will send a blank update every 10 15 minutes This length has been chosen solely to conserve battery power Automatic shut down The TD 2000A is equipped with a vibration sensor If the unit is still for more than 15 minutes it will automatically shut down to conserve battery power Any vibrations such as opening the car door or starting the engine will power the unit back up immediately When powering back up the unit will continue to function as if it were powered up normally 44 Autogood products 130 LJ Low Pressure Warning If a tyre s pressure falls below the Low Pressure Warning value the monitor
10. SAFETY 7 PACKAGE CONTENTS PARTS CHECKLIST A 8 SYSTEM COMPONENTS usu naa 11 EE o i TS 14 15 un T T unus 15 MONTON ce 18 M 19 MOUNTING ne Ope Senn nT 21 OPERATI ON uu u 23 MAIN BUTTON Mere vis T 23 MAIN BUH ONFUNCIfDNSR Q u 24 ADVANCED BUTTON FUNCTIONS u ccccccscscscscscscsssssscscscscsesssssscscscsesesscscscscsesesseesecsesesees 25 ENTERING THE SETTINGS 26 Autogood products 130 CALLING HIIS 27 CHANGING BETWEEN TRAILERS QU Eton MS li ete tutEtu ih 29 SETTING MEASUREMENT UNITS pU Fe tr 30 SETTING HIGH AND LOW 5 31 CHANGING THE VISUAL CAR LAYOUT 33 PROGRAMMING THE RELAY TD usciti 37 PROGRAMMING REPLACEMENT SENSORS n naa entrent 39 PROGRAMMING ADDITIONAL SENSORS cccsccccsscssssssescscsescsesscscscseses
11. at the top of the unit Car body Once the bracket is firmly mounted to the car body the relay can be mounted to the bracket with the supplied bolts and washers Using a Phillips head screwdriver tighten the bolts ensuring they are not over tightened If using the power cord use the optional Relay Cover and 3mm bolts supplied to prevent the plug from coming out of the socket or being damaged 17 Autogood products 130 MONITOR The LCD monitor can be powered by 2x AA batteries or your car s power using the supplied cigarette lighter adapter Please follow the steps below outlining how to install batteries into the monitor and sensors and powering up the system for the first time To install batteries push the lever down as shown and open the cover Insert the negative end of the battery onto to the spring side of the battery holder and push the other end in until it locks in place Be sure the battery polarity 15 correct and replace the cover When the monitor is powered up the boot up screen will be displayed for 3 seconds then the home screen PRESURE MONITORING SYSTEM BOOT UP SCREEN HOME SCREEN 18 Autogood products 130 SENSORS 1 Remove the sensor cap and insert the battery like shown The LCD monitor will beep and the corresponding value for that sensor blink and show 00 0 2 Replace the battery cover and ensure it is screwed
12. be aware that heat and extended driving periods can greatly alter tyre pressure and drivability If you feel your system has a fault which cannot be rectified by this procedure please contact your Tyredog dealer 51 Autogood products 130 Product specification Sensor Specification Frequency 315MHz Pressure range 0 180 PSI Accuracy Pressure 3 PSI Temp 2 Degrees Celsius Operating voltage 3 Volts DC Operating temperature 40 125 Degrees Celsius Battery life Approx 12 months depending on daily operation time Dimensions 20 5mm Diameter x 20mm Height Weight 10 g 1 Monitor Specification Frequency 433 92MHz Operating voltage 3 Volts DC batteries 6 24 Volts DC Battery life 6 months depending on daily operation time Operating temperature 20 80 Degrees Celsius Dimensions Length 102mm X width 72mm X height 29mm Weight 143 g Relay Specification Frequency 433 92MHz TX 315MHz RX Operating voltage 6 Volts DC Battery 6 24 Volts DC Supply Operating temperature 40 85 Degrees Celsius Battery life 12 months depending on daily operation time Dimensions Length 105mm X width 50mm X height 85mm Specifications are correct at time of publication Subject to change without notice 52 Autogood products 130 Heu 8518159153 YOIND VOO0e OL v DUctLll 90 000641 VOO0e OL X vODOL CIE X VOOOR OL
13. on tight 00 0 00 0 1 00 0 00 0 EG Sensor 1 is online but not fitted This is indicating that the sensor is online but not yet mounted Repeat this process with the remaining sensors until all sensors are online If any sensors fail to come online please try a battery from another sensor or consult your nearest Tyredog dealer Once all sensors are online proceed to fitting the sensors to your tyre valves 19 Autogood products 130 Visually inspect your tyre s valves for any damage or defect before fitting to ensure further damage does not occur If you do notice that something Is not right with your valves have them checked by a tyre professional 1 After removing the original valve caps slide the SecureFit fixing ring over the valve stem with the flat surface towards the wheel 2 Screw the Tyredog sensor on in a clockwise direction until you feel the valve stem come under pressure 3 Slide the SecureFit fixing ring back up to the base of the sensor and line up the grooves Once locked into place tighten the hex screw with the supplied Allen key f you do not wish to use the SecureFit fixing ring only follow step 2 20 Autogood products 130 MOUNTING BRACKET Monitor Monitor bracket screw Monitor bracket Bracket adapter Ball joint ring Ball joint Suction cup lock oOuction 1 Slide the threaded Ball J oint Ring over the ball joint 2
14. the time necessary to read the information displayed on the screen e Ensure the sensors communicate with the LCD monitor before initially fitting them to your tyres to save time and hassle e Tyredog TPMS has a unique SecureFit mechanism to prevent sensors from coming loose You can decide whether to install it or not Regularly check if sensors are fitted tightly If necessary spread water with detergent on the valve stem to see if your valves are leaking If arapid deflation warning sounds stop the car immediately to check the tyre for damage Remember to be safe when pulling over e The monitor will automatically make connections when it is powered on It is normal for some readings to freeze until sensor updates are received e All Tyredog sensors have their own unique codes and are designed to reject interference from other devices operating on the same frequency e Many factors can cause tyre pressure to rise and fall For example warm weather or long distance trips will lead to a rise in tyre pressure e t is normal for tyre pressure to decrease over long periods of time Periodically re inflate tyres especially if your car is not regularly driven e f you have any questions or problems concerning your unit that are not covered in this manual please consult your nearest Tyredog dealer 7 Autogood products 130 Package Contents Parts Checklist tem OQ Package 1 Monitor Kit LCD Monitor AA Batt
15. will beep three times and the low pressure tyre icon will be shown If the tyre pressure continues to drop the monitor will repeat the warning for every lpsi drop in value and when the tyre pressure returns to a normal state the unit will stop the alarm Note Never ignore a low pressure warning If a low pressure warning sounds safely pull over and check your tyres for irregularities or damage 45 Autogood products 130 High Pressure Warning If a tyre s pressure rises above the High Pressure Warning value the monitor will beep three times and the high pressure tyre icon will be shown If the tyre pressure continues to rise the monitor will repeat the warning for every 1psi rise in value If and when the tyre pressure returns to a normal state the unit will stop the alarm Note Never ignore a high pressure warning If a high pressure warning sounds safely pull over and check your tyres for irregularities or damage 46 Autogood products 130 High Temperature Warning If a tyre s temperature rises above the High Temperature Warning value the monitor will beep three times and the high temperature tyre icon will be shown Ifthe temperature continues to rise the monitor will repeat the warning for every 1degree rise in value If and when the tyre temperature returns to a normal state the unit will stop the alarm Note Never ignore a high temperature warn
16. ED BUTTON FUNCTIONS The three operation buttons perform different functions throughout the GUI On all but the home screen the appropriate function for that menu will be displayed above the corresponding button For the next section a table like below will be noted at the beginning of each menu option s instructions The table will show the relevant buttons and their function in relation to the option currently being explained Below 15 a chart showing each function in the appropriate menu levels ESC escape ADDISWPSENSOR ESC scape INC increase 25 Autogood products 130 ADJUSTING SETTINGS To enter the settings menu press and hold Mute for more than 7 seconds In the settings menu there are 9 options to choose from CALL RELAY Synchronise with programmed relay CHANGE TRAILER Switch between trailers refer to trailer manual SET UNIT Change the unit of measure for pressure and temperature SET THRESHOLD Change the tyre environment warning values SET CAR TYPE Change the wheel layout of your specific vehicle SET RELAY ID Enter relay ID learning mode SET SENSOR ID Enter replacement sensor learning mode CHANGE TR FUNC Set trailer function to automatic or manual CON Ui WCW N Press MUTE to scroll through the menu options Press LIGHT to enter the selected menu option Various adjustments can be made in each of these menu options to customize and opt
17. Insert the Ball Joint into the Bracket Adapter until it pops in 3 Screw the Ball J oint Ring onto the Bracket Adapter until hand tight 21 Autogood products 130 4 Place the Monitor Bracket into the Bracket Adapter clips 5 Using gentle force push the Monitor Bracket against the adapter clips and slide down until the Monitor Bracket locks in place 6 Hook the Monitor Bracket onto the Monitor line up the Monitor Screw and turn until tight 7 Align the Bracket Base to a suitable location on the windscreen 8 Push down on the base and lower the lever to apply suction 9 Adjust the angle of the Ball Joint and tighten the Ring to secure 22 Autogood products 130 Main button locations XD Mute Temperature COD Backlight When the unit is switched on the boot up Power Switch screen will be displayed followed by the CALL RELAY screen then the home screen WAKEUP ALL RELAY 23 Autogood products 130 MAIN BUTTON FUNCTIONS Pressing the mute button will disable all audible warnings This Is indicated by a strike through the speaker icon on the GUI Pressing the temperature button will display all temperatures for 3 seconds When on battery power pressing the backlight button will illuminate the screen for 3 seconds Note The screen is constantly illuminated when operating on cigarette lighter power 24 Autogood products 130 ADVANC
18. a Truck Relay being online and vice versa 28 Autogood products 130 2 CHANGE TRAILER Alternate between avallable trailer Relays SET THRESHOLD NEXT DEC decrease ADD increase the advanced settings menu highlight SET THRESHOLD and press enter 1 CALL RELAY 2 CHANGE TRAILER 3 SET UNIT NEXT ESC ENTER Multiple trailer relays can be used with the truck relay This option is ideal for use with truck fleets as trailers are used very often This function is only available when a trailer kit is programmed for use with your TD 2000A and the selected wheel layout requires two relays to be used For further instruction regarding programming and alternating between trailer relays please refer to the user manual supplied in your trailer kit For more information please consult your Tyredog reseller 29 Autogood products 130 3 SET UNIT Change the units used to display measurements Settings SET UNIT In the advanced settings menu highlight SET UNIT and press enter 1 CALL RELAY 2 CHANGE TRAILER 3 SET UNIT NEXT ESC ENTER The arrow gt symbol will be displayed next to the parameter you wish to change Press TEMP to move through the available options selected option PRESSURE UNIT BAR KPA KgCm TEMPERATURE DEGREE F NEXT ADJ ENTER Measuring unit Autogood products 130 4 SET THRESHOLD Change the alarm warning levels
19. ble batteries Do not attempt to disassemble batteries Never dispose of batteries in fire Battery Types Monitor 2x LR6 1 5volts Relay 4x LR6 1 5volts Sensors 1x CR1632 Lithium 3volts 49 Autogood products 130 Troubleshooting e f any sensors are failing to give a reading o Turn the monitor off o Remove batteries from all sensors o Remove all sensors from valves o Turn the monitor back on o Insert batteries into sensors one by one o Fit sensors to valves one by one As each sensor 15 fitted the current pressure reading will be displayed Synchronization issues can occur when the sensors are initially powered up before the monitor is turned on or if the sensors are powered up whilst installed on the valve caps f the Relay connection 15 lost o Ensure there is power at the Relay plug o Or ensure the batteries are charged o Turn the monitor off o Remove power from the relay the reconnect o The red LED will illuminate to confirm power up o Turn the monitor back on o Enter the settings menu and highlight SET RELAY ID o Press enter and then press the SYNC button on the Relay o The monitor will beep to confirm the ID Is set o Upon exiting the menu the monitor will automatically perform a relay call If successful the system will operate as normal 50 Autogood products 130 It is normal for the screen to turn dark after extended exposure to sunlight Always
20. ectly inflated tyre can fail when overloaded It is the driver s responsibility to ensure safe driving conditions are met before setting off on any trip or journey m Autogood products 130 TPMS Advantages A Tyre Pressure Monitoring System TPMS Is an efficient and effective solution to many current automotive safety Issues TPMS will help minimize driving risks and reduce fuel consumption Some benefits include Ensures safe driving conditions Tyre pressures can alter ride comfort and handling response Minimises chances of tyre blowout Blowouts are a growing cause of road accidents Even if a car can recover from a blowout the damaged tyre left behind is an even greater hazard Reduces time taken to inspect tyres It can be very time consuming to walk around large vehicles to inspect each tyre A TPMS will help pinpoint a faulty tyre to save time Everybody from driving enthusiasts to small business owners even nation wide fleet operators can benefit from the time saved by a TPMS Reduces running costs A properly inflated tyre ensures maximum fuel efficiency in all driving conditions When a tyre is underinflated it causes more rolling resistance significantly increasing fuel consumption engine and transmission wear Extends tyre life Tyres can be an expensive necessity especially in trucks or sports cars An underinflated tyre wears quicker meaning it needs replacing sooner 4 Autogood products 130
21. ery LR6 TWM Bracket Base 4 Monitor Bracket 5 Bracket Adapter A s Ball Joint Ring lt lt Sy gt Fs Se J U NS gt Cigarette we adapter Autogood products 130 Package 2 Relay amp Sensor Kit ONE ONE Mounting Bracket 4mm Relay Bolt Relay Power Cord ONE Relay Cover 9 Autogood products 130 Tyredog Sensor e A X04 4 pcs A X06 6 pcs A X08 8 pcs A X10 10 pcs CR1632 ONE PER SENSOR Lithium Battery SecureFit ring ONE PER SENSOR ONE PER SENSOR Allen Key 3 way adapter The 3 way adapter 15 sold set supplied with individually and only available from fixing screws S D an authorized TYREDOG re seller RECCOMMENDED ONLY FOR DEEP DISH OR TRUCK WHEELS Replacement 2 Replacement sensors are sold learnable sensor individually only available from Must be ordered as specific an authorized TYREDOG re seller wheel replacements only Supplied with SecureFit fixing ring If any parts are missing damaged or defective please contact the place of purchase immediately 10 Autogood products 130 System Components Monitor Front of Monitor Mounting Bracket Antenna LCD Display Power Switch Backlight Temperature Mute Autogood products 130 Screw hole for bracket
22. imize the way you use your Tyredog When adjustments are completed you can return to the main settings menu From there you can make other adjustments required Pressing exit from the main settings menu will restart the unit and return you to the home screen 26 Autogood products 130 1 CALL RELAY Manually connect to present Relays Settings SET THRESHOLD Cancel Relay Call No function In the advanced settings menu highlight CALL RELAY and press enter 1 CALL RELAY 2 CHANGE TRAILER 3 SET UNIT NEXT ESC ENTER The system will enter the Relay Call Screen and attempt to communicate with the present relay s WAKEUP ALL RELAY successful the unit will advance to the home screen 27 Autogood products 130 If the Relay Call is unsuccessful COMMUNICATE FAIL will be displayed WAKEUP ALL RELAY COMMUNICATE FAIL I If a Trailer Relay is programmed the process will repeat If the TEMP button is pressed at any time whilst the Relay Call is in progress COMMUNICATE FAIL will be displayed and the Relay Call will be cancelled To cancel a Trailer Relay call the TEMP button must be pressed during the Relay Call for the respective Relay If the Relay Call is cancelled or is unsuccessful the respective Relay will remain disconnected until the unit 15 restarted or another Relay Call process Is attempted and successful Trailer Relays will still operate without
23. ing If a high temperature warning sounds safely pull over and check your tyres for irregularities or damage 47 Autogood products 130 Battery Information Low Batteries When the monitor relay or sensor batteries are low the low battery icons will appear on the GUI to remind the user that the corresponding batteries will need to be replaced soon 26 Monitor battery T 1 Sensor battery T 3 1 Relay battery T 3 20 25 Under normal conditions sensor batteries will last approximately 12 months Depending on operation conditions and frequency of use battery life can be shorter or longer The low battery icon indicates there is approximately 1 week of battery life remaining This should be enough time to purchase new batteries Note Batteries should be replaced as soon as possible to ensure safe and efficient functionality of the system CR1632 batteries are available for purchase from your nearest Tyredog reseller electronics or battery specialists 48 Autogood products 130 Notes on batteries Keep lithium batteries out of reach of children Should a battery be swallowed immediately consult a doctor Wipe the battery with dry cloth to ensure a good contact Always be sure of correct polarity when installing batteries Observed the expiry date on old batteries Batteries may explode if shorted or mistreated Do not charge non rechargea
24. ng Monitor power status Y Constant Receiving MM Battery charged Or External power Units of measure h Battery low PSI KPA BAR C ies 126 126 128 m 128 T um 130 BY 127 127 128 Sensor power status icon Battery charged or temperature low Relay Status li T Battery charged Tyre pressure status Battery low Normal BB Under inflated Over inflated Tyre flat Sound on Sensor offline Sound off HOT High temp 14 Autogood products 130 bd Connection lost nstallation RELAY The relay can be powered by the supplied AA batteries or the power cable Permanent 12v is required for correct functionality of the relay You must ensure the relay is NOT connected to a switched power source such as accessories or ignition as this will cause synchronization issues with the monitor when powered up To open the battery cover undo the 12 Philips head screws Insert the supplied AA batteries into the battery slot observing the polarity markings When refitting the battery cover be sure to line up the contact springs correctly and ensure they are not bent upon contact If the cover is placed correctly the LED will illuminate for a few seconds to confirm the Relay is booting up Replace the 12 screws removed previously and ensure the rubber o ring Is properly seated prior to tightening 15 Autogood products 130
25. ng YES will advance to the Relay Call screen and then restart the unit 32 Autogood products 130 5 SET CAR TYPE Change the layout of your vehicle Settings SET CAR TYPE In the advanced settings menu highlight SET CAR TYPE and press enter 3 SET UNIT 4 SET THRESHOLD 5 SET CAR TYPE NEXT ESC ENTER Thirty different wheel layout types can be selected to suit your particular application Tyres monitored range from 4 to 22 with up to two Relays To scroll through the available car types press the MUTE button When the option shown on screen matches your desired car layout press the LIGHT button to accept the change If the system requires 2 Relays for the chosen layout a divider will be displayed between the two sets of wheels Pressing TEMP activates this divider and enables the Change Trailer Function If the divider is not activated the wheel set operates as a single vehicle Please remember that 2 Relays will still be required to operate in this case 33 Autogood products 130 Car type Trailer status No of wheels No of Relays Available wheel layout options CAR VISUAL NO OF NO OF TRAILER TYPE LAYOUT WHEELS RELAYS Y N BB 1 1 2 ED 34 Autogood products 130 m E c1 1 4 Ln nm on an pp ag CO HS HE OO HE an 4 TEE am og it 4 OA lg ap
26. rs Using the SET CAR TYPE function p32 set your desired car layout This layout must use the exact number of sensors you wish to run For example when upgrading an 8 wheel system to a 10 wheel system the new chosen layout must consist of 10 wheels Relays can be programmed with a maximum of 12 sensors 3 SET UNIT 4 SEI THRESHOLD 9 SET CAR TYPE NEXT ESC ENTER When this setting is confirmed the car type will be programmed into the relay 41 Autogood products 130 Now using the SET RELAY ID function p36 the Relay Code must be re learnt to ensure correct synchronization between the relay and monitor 4 SET IHRESHOLD SET CAR TYPE 6 SET RELAY ID NEXT ESC ENTER Press the SYNC button on the Relay to confirm to the monitor that the Relay is operating in the correct wheel layout Using the SET SENSOR ID function p38 you can now program any addition sensors providing they are applicable to the previously chosen layout 5 SET CAR TYPE 6 SET RELAY ID 7 SET SENSOR ID NEXT ESC ENTER Autogood products 130 SETTING TIRE 7 L Pressing the SYNC BUTTON on the Relay will Activate it as the receiving relay for the new sensors If you wish to add sensors to an additional relay such as a trailer relay be sure to program ALL sensors to the first relay before activating the next The L E D will illuminate and the relay location will be displayed on the screen SETTING TIRE
27. ruments Cleaners Carsits Miscellaneous MOUNTING Installation kits Upholstery Grilles Tubes Cable and wire Tools Miscellaneous POWER Batteries Converters Start charging equipment Capacitors e Accessories MARINE AUDIO AND ELECTRONICS Marine receivers Marine audio speakers Marine subwoofers Marine amplifiers Accessories CAR CARE PRODUCTS Additives Washer fluid Care accessories Car polish Flavors Adhesives and sealants LIQUID AND OIL Motor oil Transmission oil Brake fluid Antifreeze Technical lubricant r refere nce 2 way crossover EL y gt Hae nte 17 4 4 WAN Bie Basan eh N TI 1 100 NY Y VRON t Y AA ON We SAM e x 6 tn y T M ve 9 Jv 4 e 71 iis 52 7 gt AUTOMOBILE TYREDOG WIRLESS TIRE PRESSURE MONITORING SYSTEM Autogood products 130 IMPORTANT INFORMATIOLNN 3 TPMS ADVANTAGES 4 EXCLUSIVE FEATURES eid 5 ee cette 5 OPERA ua 6 u UU T 6 TYRE PRESSURE amp
28. ssssssscsesesessessesens 41 ADVANCED FUNCTI Z 44 INTALA T G 44 AUTOMATIC SHUT DOWN f tite onmi 44 LOW PRESSURE WARNING 6 Ry ccccccsessssssssssevessssssssssesevsusssessasseveveusesensensevenes 45 HIGH PRESSURE WARNING 46 HIGH TEMPERATURE WARNING eene tenete 47 BATTERY INFORMATI 50 NUES HERE a 48 TROUBLESHOOTING u ee RUE 50 SPECIFI CARN ONS icit dva e eR TOU 52 APPHCATION CHART siti el rH 53 NOTES IDEM 54 USER GUIDE REVISION 1 7 APR 2010 20 Autogood products 130 IMPORTANT INFORMATION This product is designed to indicate the conditions of the air inside your vehicle s tyres It should not be considered as a device that will prevent any traffic accident injury or death Tyres and valve stems must be checked before installation It is very common for rubber valve stems to require replacement without showing signs of wear Never overload your vehicle Overloading is extremely dangerous and can cause failure of tyres Suspension and driveline components A vehicle should never be operated if the GVM 15 greater than the design specification Even a corr
29. ttons to check up on your tyres except temperature Graphical user interface GUI All information is displayed together so unlike other systems there is no need to scroll through each wheel to view status e Adjustable High and low warning alarms can be set per axle e Audible You can t be expected to always keep watch of your tyres so a built in alarm will sound when there is a sudden change in pressure or temperature giving you peace of mind Design All sensors can be securely locked onto tyre valves for added safety Learnable sensors are available so in the event of theft or damage sensors can be quickly and easily replaced Sensors have unique individual codes to ensure there 15 no interference from other 433MHz devices even other TYREDOG systems All TYREDOG kits undergo strict field testing to ensure quality e The TD2000A X can monitor tyres with pressures up to 180psi so all applications are supported Sensors are treated for anti corrosion during manufacture and use rubber seals to prevent liquid and fine particles from coming in contact with the circuitry 6 Autogood products 130 Tyre Pressure amp Safety Information e Please take the time to choose a suitable location so operation can be performed quickly and safely o Be sure that the LCD monitor is firmly fixed to the windshield or dashboard using the supplied mounting hardware o Please practice safe driving and only take
30. upon receiving a product for repair and if testing and examining the product has disclosed that the alleged defect or malfunction in the product does not exist or was caused by the Customer or any third persons misuse physical abuse water damage unauthorised attempts to open repair or modify the product or improper installation this will not be covered under this warranty This Warranty is void if 1 The product has been tampered or repaired by unauthorised personnel 2 The warranty seal is broken or altered 3 The warranty period has expired 54 Autogood products 130 Y LUCUS Distributed by ZYLUX DISTRIBUTION PTY LTD 166 Christmas Street Fairfield Vic 3078 Website www zylux com au Email info zylux com au Tel 03 9482 2203 55 Autogood products 130
Download Pdf Manuals
Related Search