SS-30DV, SPS-30DM User Manual
Contents
1. Powerwerx Inc Thank you for purchasing the compact Powerwerx Switching Power Supply which is designed to supply 25 Amps continuous and 28 Amps surge up to 5 minutes at 14 1 VDC Two models are available SS 30DV with front mounted Powerpole connectors and SPS 30DM which includes front mounted digital meters SS 30DV Features e Front Connection 2 Powerpole connectors e Rear Connection 1 4 inch binding posts that also accept banana plugs or compression connections e Illuminated Power Switch SPS 30DM Features e Dual Metered Digital Amps Volts Power Supply e User Selectable variable output voltage from 5 16 VDC by adjusting the front mounted knob or fixed output at 14 1 VDC e Rear Connection 1 4 inch binding posts that also accept banana plugs or compression connections Specifications Electrical specifications e Input Range 100 120 VAC or 200 240 VAC 50 60Hz User switchable e Output Voltage model SS 30DV 14 1 VDC fixed model SPS 30DM variable 5 16 VDC Output Amperage 25 continuous 28 surge Polarity Ground Negative Internal Protection Thermal over current Internal Input Fuse 6 3 Amps at 115 VAC Ripple Peak to Peak Max lt 100mVpp Noise Peak to Peak Max lt 100mVpp Operating temperature rating 0 50 C Storage temperature 20 85 C Physical dimensions and materials e Weight SS 30DM 3 0 Ibs SPS 30DM 4 0 Ibs e Overall Dimensions 6 1 x 5x 2 5 in 154mm long 127mm wide2. 63mm tall e Fan Quiet internal cooling fan e Machined metal case front bezel Input Voltage Selection The power supply is set up for 230V AC input as shipped from the factory For 115V AC applications set the recessed 115 230 input select switch located on the rear of the power supply into the proper position Positions are identified on the switch Use a small screwdriver to Slide the switch into position No adjustment is necessary for either 50 or 60 Hz input SS 30DV SPS 30DM User Manual 263 N Berry St Brea CA 92821 714 674 0073 Phone 714 674 4949 Fax SS 30DV SPS 30DM Installation Instructions 1 Unplug the power supply from the mains supply outlet 2 Select the correct input voltage See Input Voltage Selection 3 Connect the power cable s positive red wire to the positive terminal and connect the negative black wire to the negative terminal on the back of the power supply 4 Plug the AC power cable into the power socket on the back of the radio 5 Plug the power supply into the main AC wall outlet Turning the Power Supply ON OFF Turn the power supply ON by pressing the power switch to the ON Position Before you turn the power supply OFF turn the radio off as described in the user documentation for the radio Then turn the power supply off by pressing the power switch to the OFF Position Cooling The SS 30DV power supply is cooled by convection and forced air cooling normal
3. airflow around the power supply in combination with a temperature controlled fan to improve cooling at higher levels of use The fan is temperature activated and the speed is controlled by a sensor When the temperature rises the fan speed increases Certifications e Meets FCC CFR Title 47 Part 15 Subpart B Class B CISPR 2005 ANSI C63 4 2003 e Meets CE LVD Low Voltage Directive 2006 95 EC standard e Meets EMC EN 55022 206 A1 2007 2010 EN 61000 3 2 2006 Package Contents e Power Supply e AC Power Cord 4 ft SS 30DV SPS 30DM Rev 3 12 Powerwerx Inc Caution Install Indoors SS 30DV SPS 30DM User Manual 263 N Berry St Brea CA 92821 714 674 0073 Phone 714 674 4949 Fax Install the power supply indoors It is not AN designed for operation out of doors or in wet environments Warning Safe Operation To reduce the risk of fire or electric shock AN please adhere to these warnings water or moisture Moisture Do not expose this appliance to Cleaning Unplug the power supply from the mains power outlet before cleaning Switching off the power supply will not reduce this risk Ventilation Place the power supply in an area that will allow air to flow freely around the unit This will prevent the power supply and mobile radio from overheating Do not block or obstruct any of the ventilation openings on the unit Warning Servicing This power supply should be serviced by a A qu
4. alified service technician Incorrect assembly may result in electric shock or fire This power supply contains no user serviceable parts inside Some of the components inside the power supply can operate at voltage levels that may be lethal Troubleshooting Condition Low DC Power Supply output No DC output current Power supply repeatedly trips input circuit breaker with no load connected Solution Power supply AC input voltage switch is not in the correct position Power Supply not receiving AC input voltage or is not receiving correct input voltage 1 Power Supply limiting output due to overload or ambient over temperature condition 2 Defective Power Supply Incorrect input voltage is being applied while should be 100 120 VAC or 200 240 VAC Warning Electrical Connections To reduce the risk of fire or electric shock A please adhere to these warnings The power supply should be properly connected and grounded Use the provided AC power cable to connect the power supply to a mains power outlet that is properly installed and grounded in accordance with all local codes and ordinances If the power supply cord is damaged it must be replaced with the same type to comply with safety requirements Warranty The Powerwerx support policy is simple we want you to be happy If you have a problem please feel free to contact us and we will do our best to get you up and running as soon as possib
5. le Powerwerx power supplies have a three year limited warranty We will repair or replace at our discretion your power supply if you encounter any problems within three years from the date of purchase We reserve the right to charge a reasonable fee for repairing units with user inflicted damage It is your responsibility to ship the defective unit back to Powerwerx via UPS Ground We will pay for the return shipping back to you We reserve the right to upgrade your equipment to an equivalent or better model Possible Cause On rear panel change the AC selector switch from 230V to 115V Using a voltmeter confirm AC input voltage Check input connections Confirm correct AC power cable is installed 1 Reduce DC load to 25A or less and or determine cause of over temperature condition 2 Return to place of purchase or contact Powerwerx for return authorization Using a voltmeter confirm AC input voltage Confrim input voltage switch is in the correct position Confirm correct AC power cable is installed SS 30DV SPS 30DM Rev 3 12
Download Pdf Manuals
Related Search