603 Kb Manual_L48
Contents
1. LIGHTING PROFESSIONAL LED COLOR CHANGER USER MANUAL OUAORO LHE KEEP THIS MANUAL FOR FUTURE NEEDS C Thank you for using QUADRO L 48 For the sake of safety and better operation of this projector please read this manual carefully before using and operating it lest incur any personal injury or damage to the projector SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual eS Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person No move at operating mode Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never cr2. 4 025 for RGB color changing strobe effect the white leds are off when in Auto Mode 7 6 001 Speed B and C button for revising automatic effect speed 8 7 001 Sound mode B and C button for Sound mode 9 8 001 Master amp Slave 8 000 for closing master projector 8 001 for opening master projector B and C button for revising state Please remove from the machine as the host logo DMXS12 Channels Explanations Channel IDMX 512 Value Control Content IRGB luminance eee 3 CH1 0 255 adjusting light luminance adjustment CH2 ied 0 255 adjusting red LED luminance CH3 jlgreen O 255 adjusting green LED luminance CH4 hlue O 255 adjusting blue LED luminance CH5 white O 255 adjusting white LED luminance CH6 trobe O 255 strobe speed adjustment When many lights are operating master slave synchronization only one of them can be master the others be slave otherwise they can t be synchronized Connecting controller signal cable and power DMX controller the lights will be off upon receiving DMXS12 controller signal then the lights are controlled by controller signal Master slave synchronization Connect Maps below DM X512 CONTROLLER our IN Don t connect controller C J OUT OUT OUT eee ooo IN IN IN ap 2 Q Master Slave Slave projector projector projector CLEANING AND MAINTENANCE The following point
3. MAX Quantity of lights 48 X 5W RGB 3 in 1 8 X 3W White Control channel 6 Control signal DMX 512 international standard signal Control mode DMX 512 signal control music control automatic master and slave Operating environment indoor
4. ct has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment an appropriate safety rope Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year Cautions The effect should be installed outside areas where persons may reach it walk by or be seated Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Product Introduction This series of products adopt high quality illuminant with high brightness long life and low power consumption Its structure and appearance are designed properly and better It has three function modes automatic control DMX 512 control and master amp slave synchronization control Operation instruction Operation Instruction After unpacking please check whether the projector has been damaged by transport such as screw l
5. ent operational breaks may ensure that the device will function properly for a long time Do not shake the device Avoid brute force when installing or operating the device The device shall only be used complete with its protective shield While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust The minimum distance between light output from the projector and the illuminated surface must be more than 0 1 meter Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock crash etc INSTALLATION INSTRUCTIONS Mounting the device CAUTION Please consider the EN 60598 2 17 and the other respective national norms during the installation The installation must only be carried out by a qualified person The applicable temperature for the lignting is between 0 C 45 C Do not use the lighting under or above the temperature The installation of the effe
6. imped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 0 1m distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are not subject to warranty Keep away from children and non professionals GENERAL GUIDELINES This device is a lighting effect for professional use on stages in discotheques theatres etc This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual the device was designed for indoor use Lighting effects are not designed for permanent operation Consist
7. oosening etc Check before electrification Check whether the projector has been laid correctly and stably whether the voltage of the power is adapted to the requirement otherwise we ll not be responsible for the damage of the light This projector is the first class protected equipment Notice that while using the green and yellow wires have to connect to the ground properly by professionals Please examine the electrics and voltage before powering on it Illustration Function button marked with a sign Value button marked with a sign Value button marked with a sign GUAR gt Function button marked with a sign A B C D Function details List of LED display window All the functions will be confirmed by D button No Display Function explanations 1 A 001 Address code 001 512 B and C button for increasing or decreasing address code 2 1 255 B and C button for adjusting red luminance 1 001 1 255 3 2 255 B and C button for adjusting red luminance 2 001 2 255 4 3 255 B and C button for adjusting blue luminance 3 001 3 255 5 4 255 B and C button for adjusting white luminance 4 001 4 255 6 5 001 Automatic mode 5 000 for effect automation 5 001 for RGB gradual changing effect 5 002 for RGB changing effect 5 003 4 009 for RGB single color effect 5 010 4 016 for RGB single color strobe effect 5 017
8. s have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation of dust 2 Clean the fan each week 3 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents Should you need any spare parts please order genuine parts Technical Parameters Rated voltage AC110V 220V 10 Rated frequency 50Hz 60Hz Power consumption 200W
Download Pdf Manuals
Related Search