52X-BW USER`S MANUAL
Contents
1. Easy Connection Gauges for MINI 52X BW USER S MANUAL Thank you for purchasing this PIVOT product Please read this manual carefully before installation and use Please keep this manual for future reference Improper use or disregard of these warnings may result in the injury or death of people AWARNING CAUTION Oi vor 52X BW October 2011 No 1 52X BW EURO SPEC Improper use or disregard of these warnings may cause injury to persons damage the product and other things e Do not crush the cable Please be careful that the cable does not get crushed by the seat rail or car door steel plate nor cut by any sharp steel plate as this may cause a poor connection or an electric short leading to fire or other danger e Do not work in areas where there is exces sive exhaust Due to vehicle exhaust emission poisoning or fire may result in a damage to humans e Please securely fasten the product to a stable place It is very dangerous if while in use the product falls off and interferes with braking e Do not operate while driv ing Operating or checking the dis play during driving may cause an accident please use with the utmost consideration for safety e Please be sure to store bundle away all wires with tape etc It is very dangerous to pull tangled wires by force or allow tangled wires to interfere with driving This product is for DC12V cars Installation cannot be car2. Meter Cables x2 x2 KKG Tap Screws x2 Features Z Cushion Tape Cut Connector Fuse Power Cable OQ Double sided Tapes round x 4 o Zip Ties x2 Z Lf Double sided Tape square User s Manual This Book With our 52X BW just by connecting to the diagnostic monitoring connector the MINI specialized CAN communication can be analyzed and two types of data can be simultaneously displayed Not for use with incompatible models Simple Connector Installation Low Priced Meter Holder Same Illumination Install by simply connecting to the diagnostic monitor connector and fuse box Metallic molded meter holder means reasonable pricing Newly designed lightweight meter holder with superior adhesion means less movement under vibration Uses same orange illumination as that of standard meters Displays and Uses BOOST Absolute pressure display Water Temperature Opening Demo Display 100 154 kPa 20 C 120 C During the Opening Demo the needle will move slightly to minus several times Then it will move to the maximum value and finally to reading for current measurement item e Check Boost e For Eco driving Vacuum and so on e Prevention of overheating Check Heating and so on Example This display of absolute pressure includes barometric pressure and may differ from a meter showing relative pressure mechanical type With the key in the ON position d
3. eter into the hood at finish the installation Tachometer Backside Meter Hood Backside l Tap screw Qep included Two screws Cushion tape two places Meter Hood x Meter Cable gI Fastening The Server Connect the meter cable and fuse power cord to the server e Meter Cable 3 p Connector The 3 pin connector can be connected to any of the three positions e Fuse Power Cable pin Connector Connect to the server s 3 pin connector Connect to the 1 pin connector coming L_d from the black tube of the server L ec EEE t i Use the provided double sided tape square to fasten down the server in an out of the way place Bundle up all loose wires and fasten together using the provided zip tie Reference 2 How to use the Cut Connector Reference 3 Notes about using the OBD2 Connector 1 10mm 2 10mm e ae A CAUTION Peel off of the vinyl cover at Peel off of the vinyl cover at the Do not pull on the wires when connection end of the product s wire Make sure to grip the distended trying to remove the connector the 3 4 portions when pulling it out or Wires may become disconnected K inserting it If you unable to getag Wrap around both wire coils Close tightly with cut connector the distended portion 5 m When crimping please use Wi
4. m the standard or other meter This product s boost meter reads absolute pressure and may differ from a meter using relative pressure With the key in the ON position the boost needles points toa The sensor for absolute pressure is subtracting for barometric pressure and hence the display shows minus reading minus EX Elevation of 700 meters minus 8 kPa Before the opening demo starts the needle briefly moves This is due to a special characteristic of the meter and is not a malfunction PIVOT CORPORATION 87 3 Shimookada Okada Matsumoto shi Nagano 390 0313 JAPAN http pivotjp com
5. nnector Cut Red x E Fuse CH Connecting the OBD2 Connector Locate the Diagnostic Monitoring Connector Position Open the Cover Completely insert the OBD2 Connector b UUS PI ay A iagnostic Monitoring S AMNI LI Connector ee a a Diagnostic Monitoring Connector Insert the OBD2 con nector to the diagnostic monitoring connector from the server About Using OBD2 Products If you wish to use this product in combination with products in our 3 drive Series FLAT or COMPACT PROGAUGE or REV LAMP the OBD2 Wiring Kit OBD EH sold separately 3 200 makes installation a snap For more details about using combinations of products see here http pivotjp com obd e in Combination When using the this product with products mentioned above they can only be used together in compatible model vehicles for both products Ey Fastening The Meter Affix the supplied meter hood to the back of the standard tachometer Remove the standard tachometer Unscrew the two screws torque screw T30 x 2 from the base at the back of the tachom eter and remove it by pulling it forward As the wiring for the tachometer is connected to inside the steering column it cannot be removed Carry out all operations with the wiring pulled out but connected Make sure not to lose a
6. ny removed parts Two screws T30 x 2 torque screw Unscrew the screws at the back of the tachometer Remove the screw from the hole at the back of the tachometer Put the bolt store in a safe place Affix Double sided Tape to the Stay on the Meter Hood Affix the provided double sided tape round to the two places as shown in the figure to the right Tachometer s Y Backside Remove FA Double sided Tape round Raa Lightly Fasten the Meter Hood Line up the screw holes on the original tachometer with the screw holes on the meter hood and lightly fasten with the double sided tape Do not press to strongly on the tape it may become difficult to remove When installing the 52X BW please make adjustments to line up the meters on each side Fix the meter hood with the screws Installing without Use the provided tap screws to removing tachometer fasten Return the tachometer to its original position Return the tachometer to its original place by going in the reverse order from above and securely fasten with the two screws Q Fasten the meter to the meter hood Affix the provided cushion tape to two places on the sides of the meter Pull the meter cable through the hole at the back of the meter hood and insert it into the 5 pin connector at the back of the meter After having decided the angle press the m
7. ried out on cars with other voltage batteries e Just after installation do not exert any strong force on the product When double sided tape is used for an installation be warned that when hot the tape temporarily losses adhesiveness e Do Not Use Chemical Cleansers If the unit gets dirty please wipe with a soft cloth to remove any dirt Do not use chemical cleansers such as thinner benzene or alcohol Do not install the product in any place subject to high tempera ture or any place where water may be splashed Make sure to replace all screws and parts to their original place Do not install the product ina place where it will cause dis traction Do not in any manner process take apart or make changes to this product in compatible car models A see our Web Site at http pivotjp com obd e MN 1 The display will not be proper if the ECU being used is not the standard one or if a sub computer is being used even 2 Cannot be used in combination with other company s products that use Diagnostic Monitoring Connectors 3 For details about using in combination with other PIVOT products that use Diagnostic Monitoring Connectors please 4 The meter hood can become extremely hot when exposed to direct sunlight be particularly careful of burns Please check the contents of the package Y BOOST Meter Server with OBD2 Connector Water Temp Meter Siz O Meter Hoods
8. se Server Not as normal power source Install to out of the way places EH Connecting to a Power Source Remove the Cover of the Fuse Box Use a flathead screwdriver or such tool to remove the cover of the fuse box found on the side of the panel to the right of the steering wheel Fuse Box Insert the Fuse Remove the fuse for IGN 12 V with key switch ON and insert the 7 5A mini fuse from the fuse power cable Insert with the connecting wire at the left M Fuse included Reference 1 The following is just one example of wiring to the fuse box of a BMW MINI COOPER S MF16S steering wheel on right If your model is different and you are unsure of how to connect please contact your dealer Ex BMW MINI COOPER S MF16S steering wheel on right 2008 MODEL e E gZ i 3S Sets Seg SISess5 SIR BBS Front of the fuse box Position 4th column from the left and 5th row from the top Number 32 or 34 Capacity 7 5A If you wish to get power from a fuse other than the 7 5A mini fuse please purchase separately If you are unable to get power from the fuse box please wire directly to IGN 12V with key in ON position Do not connect the red wire coming from the OBD2 connector S IGN E Cut connector Not as normal power source or soldering 1 pin Co
9. th some car models it p Z ithe connor crimpers or use pliers to bend and then solder together may be difficult to get a H by pulling on the good grip on the connector end of the zip tie a N Insulate with vinyl tape Basic Operation gd START Opening Demo Key Switch ON For Simultaneous Double Engine start Display Real display Each meter will display actual measurements Meter OFF The needle stops at the key OFF position ll STOP Key Switch OFF Engine stop Troubleshooting Trouble Possible Causes Possible Solutions Does not work with Engine start Poor connection of meter cable OBD2 connector or fuse Please reconfirm whether wiring and connections are correct or not If wiring has been direct to power the red wire may have been improperly wired or there is a poor connection The opening demo works fine but after that nothing happens The unit has been installed into an incompatible car model Please check the Fitting List The displayed values are different from the standard meter The unit has been installed into an incompatible car model Please check the Fitting List Due to the ECU information received the displayed values on this product may differ from those of stan dard or other meters The boost pressure display is different fro
10. ue to altitude the boost needle may show a minus reading A If the boost limiter has been made inactive the display may not function properly Part Names e Meter e Server View from Meter Connection E Meter Output Connector x Dial Connect the Meter Cable BOOST Needle X100kPa w Shows the current values STEPPING GAUGE 0 View from Car Connection 7 EJ OBD2 Connector Connect to get Communication Signal ey p EJ 1 pin Connector 2 Connect the Fuse Power Cable Ell WIRING METHOD and INSTALLATION BASIC WIRING Please carry out wiring with the engine turned OFF and the key removed Connect to Power IGN 12V with key switch ON i i M Not as normal power source Backside Backside of Meter of Meter AL Fuse 1 pin Connector Red SO m Server 1 j 5 pin Connector Diagnostic i i monitoring 3 pin Connector Meter Cable connector E OBD2 Connector The 3 pin ae e be When inserting make sure that the OBD2 connected to any of the three connector is placed in the proper direction positions Installation Example In case of MINI R56 OBD2 Connector Connect to the Diagnostic Monitoring Connector Connect to IGN Fu
Download Pdf Manuals
Related Search