Addendum to Studio Color 575 Menu System
Contents
1. Press and hold the lt Menu gt button until ADDR appears on the LED display Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the lt Enter gt button to select the INFO menu Using the lt Up gt and lt Down gt arrow buttons scroll to the L HR option and press the lt Enter gt button to select the L HR option The LED will display the number of hours the lamp has been on since this option was reset Viewing the Number of Current Lamp Strikes L ST To view the number of times the fixture has attempted to strike turn on the current lamp Note Press and hold the lt Menu gt button until ADDR appears on the LED display Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the lt Enter gt button to select the INFO menu Using the lt Up gt and lt Down gt arrow buttons scroll to the L ST option and press the lt Enter gt button to select the L ST option The LED will display the number of times the fixture has struck the current lamp Lamp strikes are automatically reset when the lamp hours are reset see Resetting Lamp Hours L RS below Viewing the Current Software Version VER To view the current software version a Ge Q pa E t 7 lt m ma D a ES m 20 Ww Note Press and hold the lt Menu gt button until ADDR appears on the LED display2. Press the lt Enter gt button to enter the FROM menu A Ea 3 we page 17 Studio Color 575 User s Manual Addendum TY om en G3 Cole C3 E35 A 9 S3 S ea S 5 Using the lt Up gt and lt Down gt arrow buttons scroll to the scene F001 F016 that you want to copy from source scene Press the lt Enter gt button to select the desired scene The LED will display TO Press the lt Enter gt button to enter the TO menu 7 Using the lt Up gt and lt Down gt arrow buttons scroll to the scene T001 T016 that you want to copy to destination scene Press the lt Enter gt button to select the desired scene The fixture will copy the desired scene to the selected scene location When the fixture finishes the copy successfully DONE will appear briefly in the fixture s LED display on Capturing a Preset Scene CAPT Preset capturing is a way to automate the creation of scenes on multiple Studio Color 575 fixtures connected to a DMX 512 link Use a DMX controller to create a scene then save capture the scene into a fixture s presets to play back the scene without the controller When capturing a scene into a fixture s presets all construct values must be constant i e there cannot be any pan tilt movement After creating a scene with your DMX controller follow the instructions below for each fixture on which you want to capture p
3. ADDR appears on the LED display 7 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the PRST menu and press the RSI lt Enter gt button to select the PRST menu fell 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the DFLT menu and press the lt Enter gt button to select the DFLT menu The LED display will show OK 4 Press the lt Enter gt button to enable the self demo or press lt Menu gt to exit the menu option Note To play the fixture s self demo you must set preset playback on see Setting Preset Playback PLAY on page 17 Studio Color 575 User s Manual Addendum page 18 Programming Overview Before programming your fixtures you must be aware of some programming terms and definitions These terms are defined in this section Scene A scene is a combination of the different construct values you choose A construct is a unique fixture feature for example focus color or rotating effects Each scene consists of all of the construct values you select and can be as simple or complex as you want When you play back more than one scene it becomes a sequence A sequence that continuously repeats is called a loop Studio Color 575 fixtures always play back all contiguously programmed scenes in a continuous loop The loop plays back until you either turn the fixture off or stop scene playback You must create the scenes contiguously in other words
4. COL I lt a B Wn g mg N Using the lt Up gt and lt Down gt arrow buttons scroll to the COL construct and press the lt Enter gt button to select the Color wheel position construct Using the lt Up gt and lt Down gt arrow buttons scroll to the desired Color wheel position value in this example M056 and press the lt Enter gt button to select the desired value Selecting a Cyan Wheel Position CYAN YAN 1 2 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the CYAN construct and press the lt Enter gt button to select the cyan color wheel position construct Using the lt Up gt and lt Down gt arrow buttons scroll to the desired cyan color wheel position value and press the lt Enter gt button to select the desired value in this example a cyan color wheel position is not available because a COL value of M056 was chosen Selecting a Magenta Wheel Position MAGN MAGN 1 Using the lt Up gt and lt Down gt arrow buttons scroll to the MAGN construct and press the lt Enter gt button to select the magenta color wheel position construct Using the lt Up gt and lt Down gt arrow buttons scroll to the desired magenta color wheel position value and press the lt Enter gt button to select the desired value in this example a magenta color wheel position is not available because a COL value of M056 was chosen Selecting a Yellow Wheel Pos
5. Preset playback indicator MENU ENTER page 23 Studio Color 575 User s Manual Addendum Synchronizing Preset Playback After you have created one or more scenes for your fixtures you can synchronize the preset scene playback for all Studio Color 575 Studio Spot 575 ES 1 EC 1 Studio Spot 250 Studio Color 250 Technobeam Technopro or Technoray fixtures in the link Note Synchronizing preset playback is applicable for fixtures operating in stand alone mode only Do not include a DMX controller in the link while synchronizing preset scene playback Synchronizing playback allows you to set all applicable fixtures to a master clock so that all fixtures have a definite synchronized starting point when playing back their sequences or loops It is the master fixture which determines the sequence length for all the fixtures in the link regardless of the number of programmed scenes or the sequence length of the individual slave fixtures When the master fixture reaches the end of its last scene all fixtures will restart at scene 1 regardless of whether the slave fixtures have finished playing their scenes and all the clocks will be reset to zero For example if a slave fixture has a shorter sequence length it will continuously repeat its sequence until the master fixture resets all the clocks see Figure 2 If a slave fixture has a longer sequence length it will restart at scene 1 before it completes its entire
6. Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the lt Enter gt button to select the INFO menu Using the lt Up gt and lt Down gt arrow buttons scroll to the VER option and press the lt Enter gt button to select the VER option The LED will display the fixture s current software version The software version is also displayed when you exit the menu system and the normal alphanumeric display cycles between displaying the software version the fixture name and the fixture address Studio Color 575 User s Manual Addendum page 6 Resetting Lamp Hours L RS This menu item allows you to track the number of hours the current lamp has been operating To reset the current lamp hours to zero Press and hold the lt Menu gt button until ADDR appears on the LED display 1 TNEQ 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the lt Enter gt button to select the INFO menu f2S 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the L RS option and press the lt Enter gt button to select the L RS option The LED will display 0000 when the lamp hours are reset Note This option has a 5 second delay to avoid inadvertent changes To reset the lamp hours you must press and hold the lt Enter gt button for at least 5 seconds Viewing the Current Fixture Hours F HR To v
7. if you have a fixture with a newer software version you can crossload the newer software to all other Studio Color 575 Studio Spot 575 ES 1 and EC 1 fixtures on the link To crossload software L Disconnect or bypass any controllers serial data distributors data line optoisolators and any fixtures using RS 422 communications such as Dataflash AF1000 xenon strobes Intellabeam fixtures and Emulator laser simulators These devices will block communication between your crossloading fixture and any other Studio Color 575 Studio Spot 575 EC 1 or ES 1 fixtures on the link On the crossloading fixture only press and hold the lt Menu gt button until ADDR appears on the LED display Using the lt Up gt and lt Down gt arrow buttons scroll to the MODE menu and press the lt Enter gt button to select the MODE menu Studio Color 575 User s Manual Addendum page 12 4 Using the lt Up gt and lt Down gt arrow buttons scroll to the XLD option and press the lt Enter gt button to select the XLD option The fixture will upload its software to all other Studio Color 575 Studio Spot 575 ES 1 and EC 1 fixtures on the link The Transmit LED on the crossloading fixture will remain on or flicker The Transmit and Receive LEDs on receiving fixtures will flicker while the crossload is in progress and UPLD will appear on the alphanumeric display as each fixture receives the software upload
8. scene 1 scene 2 scene 3 and so on without skipping a scene because the fixture automatically repeats when it encounters the first unprogrammed scene DMX Controller vs Stand Alone Operation You may save time by programming your fixtures using a DMX controller and then capturing the scene to the on board memory of multiple Studio Color 575 fixtures However because controllers cannot transmit crossfade XFAD delay DLAY or time TIME construct values you must use preset programming to manually set those construct values for each fixture You can use either a controller or the fixture s on board memory to create and play back scenes but not both at the same time In other words you cannot create a scene using the on board memory and play it back using a controller You also cannot use a controller at the same time onboard scenes are playing When using a DMX controller you can program an unlimited number of sequences and retain direct control over the Studio Color 575 fixtures at all times Using preset programming you can build one sequence up to 16 preset scenes per fixture You can also synchronize scene playback for all fixtures on the link while operating in stand alone mode However in stand alone mode once you begin playing back the sequence you do not have direct control over the fixtures MSpeed vs Full Speed Some constructs allow you to choose either full speed or MSpeed motor speed changes A full speed change
9. Map on page 1 Creating a Scene Step By Step Example Follow the example below to create a sample scene using the fixture s menu system to choose a value for each of the fixture s available constructs Choosing a Scene to Create Edit AddR 1 PRST c SNOI 4 Press and hold the lt Menu gt button until ADDR appears on the LED display Using the lt Up gt and lt Down gt arrow buttons scroll to the PRST menu and press the lt Enter gt button to select the PRST menu Using the lt Up gt and lt Down gt arrow buttons scroll to the EDIT menu and press the lt Enter gt button to select the EDIT menu Using the lt Up gt and lt Down gt arrow buttons scroll to the scene you want to create in this example SNO1 and press the lt Enter gt button to select the desired scene Opening the Shutter SHUT GAOT OPE Using the lt Up gt and lt Down gt arrow buttons scroll to the SHUT construct This will be the first construct displayed Press the lt Enter gt button to select the shutter construct Using the lt Up gt and lt Down gt arrow buttons scroll to the desired shutter value in this example OPEN and press the lt Enter gt button to select the desired value Selecting a Dim Value DIM BIM am 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the DIM construct and press the lt Enter gt button to select the dim
10. lt Menu gt button until ADDR appears on the LED display Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the lt Enter gt button to select the INFO menu Using the lt Up gt and lt Down gt arrow buttons scroll to the SENS menu and press the lt Enter gt button to select the SENS menu Using the lt Up gt and lt Down gt arrow buttons scroll to the desired sensor option listed above and press the lt Enter gt button to select the desired option to view its sensor information Test Menu TEST The Test menu allows you to manually home the fixture place the fixture in setup mode perform fixture self tests store new boot code information and manually turn the lamp on or off If you are experiencing problems that you suspect are mechanical performing fixture self tests will help to determine where the problem lies The procedures below are listed in the order that they appear on the menu map Note To see the effects of the self tests the lamp must be on If the lamp is off when you run the self test the LED will display STRK to indicate that the lamp is not struck and the fixture will attempt to strike the lamp automatically Homing the Fixture HOME To manually home the fixture Add 1 HOME 3 4 Press and hold the lt Menu gt button until ADDR appears on the LED display Using the lt Up gt and lt Down gt arrow button
11. means the change is completed in the shortest length of time after the wheel starts moving An MSpeed motor speed change occurs smoothly over the entire MSpeed time value you assign For example if you choose a value of 10 seconds for an MSpeed fixed color wheel change from position 2 to position 4 the fixed color wheel will take 10 seconds to move from position 2 to position 4 However if your MSpeed value is longer than the crossfade or delay time the color change will not be complete before the next scene starts All fixtures that have the same MSpeed value will reach their destination at the same time regardless of the distance travelled A DMX table of MSpeed times is shown in Appendix C of the Studio Color User s Manual Forward and Reverse Spins A forward spin on all wheels and positions means the wheel or position spins clockwise as you are looking at the projected image A reverse spin means the wheel or position spins counter clockwise page 19 Studio Color 575 User s Manual Addendum Preset Programming This section provides a step by step example of how to program your fixtures for stand alone operation using the on board memory in each fixture to create store and play back scenes Preset programming involves accessing the fixture s menu system For more information on how to access the menu system see page I 13 of the Studio Color User s Manual For a complete menu map of the preset programming options see Menu
12. sequence 00 00 00 00 15 00 00 35 00 00 50 00 01 00 00 01 20 00 01 30 00 01 40 00 01 55 00 Master Scene 1 Scene 2 Scene3 Scene4 Scene5 Scene6 Scene7 Scene8_ restarts pa acy 00 00 00 00 10 00 00 55 00 01 30 00 01 40 00 Slave 1 Scene 1 Scene 2 Scene 3 Scene 1 Scene 2 scene not finished restarts 00 00 00 00 10 00 00 20 00 00 40 00 01 55 00 Slave2 Scene 1 Scene 2 Scene 3 Scene 4 Scene 5 not played restarts Figure 2 Example of synchronized playback To enable synchronized playback 1 Link the fixtures you want to synchronize Make sure you terminate the last fixture in the link and that there are no DMX controllers on the link 2 Assign one fixture as the master fixture by assigning it a unique DMX start channel 1 or fixture number 1 Make sure no other fixture on the link is assigned DMX start channel 1 or fixture number 1 3 Set preset playback on for all fixtures on the link see Setting Preset Playback PLAY on page 17 Note If there is a controller on the link or if more than one fixture is assigned a DMX start channel 1 or fixture number 1 the master fixture s LED will display LINK BUSY ERR wait for two minutes then try to transmit the time code again Studio Color 575 User s Manual Addendum page 24
13. DIT This menu item allows you to edit or create a scene using the fixture s on board scene memory Using this menu option you can change the value of any construct in any of the on board scenes For detailed information on editing or creating a scene see Preset Programming on page 20 To edit create a scene cijf 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 1 Using the lt Up gt and lt Down gt arrow buttons scroll to the PRST menu and press the lt Enter gt button to select the PRST menu za LA A N Using the lt Up gt and lt Down gt arrow buttons scroll to the EDIT menu and press the lt Enter gt button to select the EDIT menu ET GE 4 U9 GNOI 4 Using the lt Up gt and lt Down gt arrow buttons scroll to the scene SN01 to SN16 that to you want to edit or create and press the lt Enter gt button to select the desired scene Copying an On Board Memory Scene COPY Press and hold the lt Menu gt button until ADDR appears on the LED display D az mi 70 Using the lt Up gt and lt Down gt arrow buttons scroll to the PRST menu and press the lt Enter gt button to select the PRST menu a D Ww H N Using the lt Up gt and lt Down gt arrow buttons scroll to the COPY menu and press the lt Enter gt button to select the COPY menu ROMI 4 The LED will display FROM
14. Studio Color 575 Addendum Overview This addendum replaces the menu map and menu item descriptions listed in Chapter 3 of the Studio Color User s Manual p n 60600061 With the addition of preset programming for stand alone operation new options have been added to the Studio Color menu map See individual subsections in this addendum for descriptions of each menu item and for preset programming information Menu Map Menu Menu Menu Menu Menu Description Level 1 Level 2 Level 3 Level 4 Level 5 ADDR Fxx Cxxx change the existing fixture number DMxX start channel LAMP view whether the lamp is on L ON off LOFF attempting to strike STRK or experiencing an error ERR L HR view the current number of lamp hours L ST view the current number of lamp strikes VER view the fixture s software version LIRS reset lamp hours to zero press and hold the lt Enter gt button for 5 seconds to zero the value F HR view the current number of fixture hours E RS reset fixture hours to zero press and hold the lt Enter gt button for 5 seconds to zero the value CURR view the fixture s current internal temperature C MINT view the fixture s minimum internal temperature C reached since this option was reset TEMP z MAXT view the fixture s maximum internal temperature C reached since this opti
15. Studio Spot XLD 575 ES 1 and EC 1 fixtures with preset programming ability on MODE the link TYPE SPOT set the fixture type to Studio Spot 575 COLR set the fixture type to Studio Color 575 ON set factory defaults on FACT OFF set factory defaults off Note Selecting this option has no effect on individual preset values CHNL DMX set control method to DMX start channel ADDR set control method to fixture number ON set LED display on DSPL OFF set LED display off SET DIM dim LED display D IN ON invert LED display orientation OFF set normal LED display orientation P IN ON set pan invert on OFF set pan invert off ON set tilt invert on HIN OFF set tilt invert off Studio Color 575 User s Manual Addendum page 2 Menu Menu Menu Menu Menu Level 1 Level 2 Level 3 Level 4 Level 5 Besctiption ON set pan tilt swap on SWAR OFF set pan tilt swap off S DN 5 MN set shutdown time for 5 minutes 10MN set shutdown time for 10 minutes SET LAMP L ON strike the lamp LOFF extinguish the lamp BOOT copy the boot sector CODE Factory use only PLAY OFF set preset playback off ON set preset playback on SCN display which scene is currently playing OPEN open shutter CLSD close shutter SHUT P001 periodic shutter strobe at specified intervals slow P001 to fast P120 P120 nace j shutter strobe at random interv
16. When the crossload has finished successfully DONE will appear briefly in the LED display of the crossloading fixture and all other fixtures will home XLo Note If a new boot code was included with the latest software the LED will display a BOOT DIFF error To correct the boot code you must copy the new boot code for each fixture see Copying the Boot Code BOOT on page 11 Setting the Fixture Type TYPE Use this menu item to change the fixture type to either Studio Spot 575 or Studio Color 575 All fixtures are shipped from the factory set to the correct fixture type However if the fixture s logic board is replaced you must ensure the new board is set to the correct fixture type To set the fixture type ddk 1 Press and hold the lt Menu gt button until ADDR appears on the LED display MOJE 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the MODE menu and press the lt Enter gt button to select the MODE menu TYPE 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the TYPE menu This will be the first menu displayed Press the lt Enter gt button to select the TYPE menu POT 4 Using the lt Up gt and lt Down gt arrow buttons choose the SPOT option for Studio Spot 75 or fixtures or the COLR option for Studio Color 575 fixtures Press the lt Enter gt button to COLR select the desired option Set Menu SET The Set
17. a and yellow color wheels MSpeed allows indexed positioning of the fixed color wheel so that the wheel MLK takes the quickest path and snaps to the center of the color MSpeed same as a COLC value of M CN but allows up to 2 continuous M2CN rotations of the cyan magenta and yellow color wheels to allow a choice of path to the specified position M2FS same as a COLC value of M FS M2RS same as a COLC value of M RS M2LK same as a COLC value of M LK D000 select a color wheel position in degrees from 0 D000 to 358 COL D358 D358 only available with COLC value of CN 2CN M CN or M2CN page 3 Studio Color 575 User s Manual Addendum Menu Menu Menu Menu Menu Level 1 Level 2 Level 3 Level 4 Level 5 Beseription select a fixed color wheel forward spin speed from slow F001 to F001 fast F124 only available with COLC value of FS 2FS M FS or M2FS F124 Note This option allows direct control of the cyan magenta and yellow color wheels cycle the cyan magenta and yellow color wheels through 9 factory selected colors from red to blue to green at variable speeds from M001 slow M001 to fast M128 only available with COLC value of FS M128 2FS M FS or M2FS Note This option sets the fixed color wheel to the open white position and does not allow direct control of the cyan magenta or yellow
18. als slow N001 to fast N120 DIM D000 select a dim value from dark D000 to bright D255 PAN zi a 7 select a pan value from 185 to 185 of the pan range TILT 741227 select a tlt value from 112 5 to 112 5 of the tit range CN allows continuous positioning at any point on the fixed cyan magenta and yellow color wheels full speed allows either a forward spin of the fixed color wheel or a variable FS speed red green blue cycle of the cyan magenta and yellow color wheels full speed allows either a reverse spin of the fixed color wheel or a variable RS speed random cycle of the cyan magenta and yellow color wheels full speed allows indexed positioning of the fixed color wheel so that the wheel LK takes the quickest path and snaps to the center of the color full PRST speed SNO1 same as a COLC value of CN but allows up to 2 continuous EDIT SN16 2CN rotations of the cyan magenta and yellow color wheels to allow a choice of path to the specified position 2FS same as a COLC value of FS 2RS same as a COLC value of RS COLC 2LK same as a COLC value of LK MCN allows continuous positioning at any point on the fixed cyan magenta and yellow color wheels MSpeed allows either a forward spin of the fixed color wheel or a variable MFS speed red green blue cycle of the cyan magenta and yellow color wheels MSpeed allows either a reverse spin of the fixed color wheel or a variable MRS speed random cycle of the cyan magent
19. color wheels stop any color wheel spin and move all wheels to the open white STIL position only available with COLC value of FS RS 2FS 2RS M COL FS MRS M2FS or M2RS select a fixed color wheel reverse spin speed from slow R001 to R001 fast R124 only available with COLC value of RS 2RS M RS or M2RS R124 Note This option allows direct control over the cyan magenta and yellow color wheels randomly cycle the cyan magenta and yellow color wheels at variable speeds from slow N001 to fast N128 only available with NO001 COLC value of RS 2RS M RS or M2RS N128 Note This option sets the fixed color wheel to the open white position and does not allow direct control of the cyan magenta or yellow color wheels C 0 select a fixed color wheel full color position only available with C5 COLC value of LK 2LK M LK or M2LK D000 select an exact position on the cyan color wheel from 0 D000 to CYAN D358 358 D358 only available with COLC value of CN LK 2CN 2LK M CN or M2CN PRST EDIT SNO1 D000 select an exact position on the magenta color wheel from 0 D000 SN16 MAGN D358 to 358 D358 only available with COLC value of CN LK 2CN 2LK M CN or M2CN D000 select an exact position on the yellow color wheel from 0 D000 to YELW D358 358 D358 only available with COLC value of CN LK 2CN 2LK M CN or M2CN OPEN select the open no lens position on the lens wheel LENS D001 select a s
20. construct Using the lt Up gt and lt Down gt arrow buttons scroll to the desired dim value in this example D255 and press the lt Enter gt button to select the desired value Selecting a Pan Value PAN PAN t 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the PAN construct and press the lt Enter gt button to select the pan construct Using the lt Up gt and lt Down gt arrow buttons scroll to the desired pan value from 185 to 185 and press the lt Enter gt button to select the desired value Studio Color 575 User s Manual Addendum page 20 Selecting a Tilt Value TILT fa 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the TILT construct and press the lt Enter gt button to select the tilt construct Using the lt Up gt and lt Down gt arrow buttons scroll to the desired tilt value from 112 5 to 112 5 and press the lt Enter gt button to select the desired value Choosing a Color Control Value COLC E c3 m e a E N 1 Using the lt Up gt and lt Down gt arrow buttons scroll to the COLC construct and press the lt Enter gt button to select the color wheel control construct Using the lt Up gt and lt Down gt arrow buttons scroll to the desired color wheel control value in this example FS and press the lt Enter gt button to select the desired value Selecting a Color Wheel Position
21. copied to each fixture This is apparent if the LED displays a BOOT DIFF error Do not remove power from the fixture while performing a boot copy You can copy the new boot code using either the TEST menu or the SET menu To accept and store the new boot code using the TEST menu Add G z SJE gE page 11 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the TEST menu and press the lt Enter gt button to select the TEST menu 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the BOOT option and press the lt Enter gt button to select the BOOT option The fixture will store the new boot code then automatically home Studio Color 575 User s Manual Addendum Turning the Lamp On or Off LAMP You can manually turn the lamp on and off using either the TEST menu or the SET menu To manually turn the lamp on or off via the TEST menu Add 1 m 4 CAMP 3 4 5 Press and hold the lt Menu gt button until ADDR appears on the LED display Using the lt Up gt and lt Down gt arrow buttons scroll to the TEST menu and press the lt Enter gt button to select the TEST menu Using the lt Up gt and lt Down gt arrow buttons scroll to the LAMP menu and press the lt Enter gt button to select the LAMP menu Using the lt Up gt and lt Dow
22. e s tilt motion AddR 1 Press and hold the lt Menu gt button until ADDR appears on the LED display Sei 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the SET menu and press the J lt Enter gt button to select the SET menu T IN 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the T IN menu and press the 4 lt Enter gt button to select the T IN menu 4 Using the lt Up gt and lt Down gt arrow buttons choose the ON option to invert the fixture s tilt motion or the OFF option to return the fixture s tilt motion to normal orientation Press the lt Enter gt button to select the desired option Swapping Pan and Tilt SWAP To swap the fixture s pan and tilt motion Aidcf 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the SET menu and press the lt Enter gt button to select the SET menu page 15 Studio Color 575 User s Manual Addendum 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the SWAP menu and press the J lt Enter gt button to select the SWAP menu 4 Using the lt Up gt and lt Down gt arrow buttons choose the ON option to swap the fixture s pan and tilt motion or the OFF option to return the fixture s pan and tilt motion to normal orientation Press the lt Enter gt b
23. e having a particular problem with a fixture for example a color wheel that does not respond to commands from the controller The following DMX status information is available for viewing ERRS total number of DMX errors FE number of framing errors OV overruns changing values could indicate data link connector problems CE DMX checksum errors STRT start code The following construct values are available for viewing PANH high 8 bit pan value PANL low 8 bit pan value TLTH high 8 bit tilt value TLIL low 8 bit tilt value COLC color control value COL color wheel position value CYAN cyan color wheel position value MAGN magenta color wheel position value YELW yellow color wheel position value LENS lens wheel position value FRST frost wheel position value SHUT shutter strobe value DIM shutter dim flag value MSPD MSpeed time value CNTL control channel value CSUM DMX checksum value To view the DMX status and construct values 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the lt Enter gt button to select the INFO menu Ea 5 S eaten me C3 70 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the DMX menu and press the lt Enter gt button to select the DMX menu Using the lt Up gt and lt Down gt ar
24. ential order To create a loop you must first create two or more contiguous scenes see Creating a Scene Step By Step Example on page 20 After you have created at least two scenes go to the next available scene and choose the ZERO menu option to erase any programmed construct values and mark the end of a loop Note If you program all available on board scenes you do not have to mark the end of the loop When preset playback is set on the fixture will automatically loop after playback of all programmed scenes Playing Back a Loop To play back a loop you must set preset playback mode on for each fixture see Setting Preset Playback PLAY on page 17 When preset playback is set on your fixture will automatically begin playing back the first scene and continue through the loop Note You must program scene 1 to enable preset playback The fixture has two ways to indicate that preset playback is on First the LED dot indicates preset will display a dot in the lower right corner see Figure 1 Second during playback is ON normal operation the alphanumeric LED cycled information will be changed A to display PRST instead of the fixture s software version Vxxx Ti If power is removed during playback when power is reapplied the fixture will l home and begin playback at the first scene To stop playback you must i n W manually set playback mode off see Setting Preset Playback PLAY on page 17 Figure 1
25. ess Menu ADDR on page 5 Changing the Display Output DSPL This menu item allows you to change the appearance of the fixture s alphanumeric LED display You can set the display on or off or you can dim the display to reduce visibility To change the display output cic f 1 Press and hold the lt Menu gt button until ADDR appears on the LED display D ET 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the SET menu and press the lt Enter gt button to select the SET menu Be g5PL 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the DSPL menu and press the lt Enter gt button to select the DSPL menu 4 Using the lt Up gt and lt Down gt arrow buttons choose the ON option to set the LED display to normal intensity the OFF option to turn the LED display off or the DIM option to reduce the LED display visibility Press the lt Enter gt button to select the desired option Note If you set the LED display off the LED display will be turned off only when you exit the menu system Studio Color 575 User s Manual Addendum page 14 Inverting LED Characters D IN This menu item allows you to invert the orientation of the LED display s alphanumeric characters This option is useful if your fixture is standing upright i e resting on its bottom panel on the floor To invert the LED display AdgR 1 Press and hold the lt Menu g
26. ff or on view which scene is currently playing and create edit a scene using the on board memory to program the fixture for stand alone operation This menu also allows you to copy a scene within the fixture s on board memory capture a scene from your DMX controller to the fixture s on board memory and enable the fixture s factory programmed preset sequence self demo Setting Preset Playback PLAY This menu option allows you to turn preset playback on or off and view which scene is currently playing in preset playback mode To set preset playback on or off or to view the current scene Aedcdf 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the PRST menu Press the seu lt Enter gt button to select the PRST menu o Ayl 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the PLAY menu This will be the first option displayed Press the lt Enter gt button to select the PLAY menu 4 Using the lt Up gt and lt Down gt arrow buttons scroll to the ON option to set preset playback on the OFF option to set preset playback off or the SCN option to display which scene is currently playing Press the lt Enter gt button to select the desired option Note Scene 1 must be programmed before the fixture can play back scenes Editing or Creating an On Board Memory Scene E
27. iew the number of hours the fixture has been on since this option was reset Aid 1 Press and hold the lt Menu gt button until ADDR appears on the LED display ThE 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the INFU lt Enter gt button to select the INFO menu 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the F HR option and press the lt Enter gt button to select the F HR option The LED will display the number of hours the fixture has been on since this option was reset Resetting Fixture Hours F RS This menu item allows you to track the number of hours the fixture has been operating To reset the fixture hours to zero 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the INFU lt Enter gt button to select the INFO menu E RS 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the F RS option and press the lt Enter gt button to select the F RS option The LED will display 0000 when the fixture hours are reset Note This option has a 5 second delay to avoid inadvertent changes To reset the fixture hours you must press and hold the lt Enter gt button for at least 5 seconds Viewing the Logic Board Temperature TEMP This menu option allows you to view the l
28. iewing Sensor Information SENS This menu option allows you to view whether a specified sensor if working correctly If you receive a SENS ERR error message on the LED display this information may help you determine where the problem originates The following sensor information is available e SENP view whether the pan sensor is obstructed OFF or is not obstructed ON e SENT view whether the tilt sensor is obstructed OFF or is not obstructed ON e SENI view whether the fixed color wheel cyan color wheel and lens wheel sensor is obstructed OFF or is not obstructed ON e SEN2 view whether the magenta color wheel yellow color wheel and frost wheel sensor is obstructed OFF or is not obstructed ON e SVCC view whether the sensor is receiving power ON or is not receiving power OFF page 9 Studio Color 575 User s Manual Addendum TIME Factory use only PCOR view the number of pan encoder corrections TCOR view the number of tilt encoder corrections DUTY view the duty cycle and phase of the pan and tilt encoders this information is displayed as a percentage and is normally 10 of 50 e PPOS view the encoder s pan position value represented as a number of encoder counts e TPOS view the encoder s tilt position value represented as a number of encoder counts To view the specified sensor information Press and hold the
29. is not obstructed ON SEN1 displays whether the fixed color wheel cyan color wheel and lens wheel sensor is obstructed OFF or is not obstructed ON INFO SEN displays whether the magenta color wheel yellow color wheel and SENS frost wheel sensor is obstructed OFF or is not obstructed ON SVCC displays whether sensor is receiving power TIME Factory use only PCOR displays the number of pan encoder corrections TCOR displays the number of tilt encoder corrections DUTY displays the duty cycle and phase of the pan and tilt encoders PPOS displays the encoder s pan position value TPOS displays the encoder s tilt position value HOME home the fixture S UP place the fixture in setup mode for mechanical homing ALL self test all constructs PAN self test pan movement TILT self test tilt movement COLR self test fixed color wheel movement MAGN self test magenta color wheel movement SELF YELW self test yellow color wheel movement CYAN self test cyan color wheel movement TEST LENS self test lens wheel movement FRST self test frost wheel movement SHUT self test shutter strobe movement DIM self test dim flag movement BOOT copy the boot sector STAT view whether the lamp is on L ON off LOFF attempting to strike STRK or is experiencing an error ERR LAME LOFF extinguish the lamp L ON strike the lamp DISP self test LED display crossload fixture software to all other Studio Color 575
30. ition YELW v 2 page 21 Using the lt Up gt and lt Down gt arrow buttons scroll to the YELW construct and press the lt Enter gt button to select the yellow color wheel position construct Using the lt Up gt and lt Down gt arrow buttons scroll to the desired yellow color wheel position value and press the lt Enter gt button to select the desired value in this example a yellow color wheel position is not available because a COL value of M056 was chosen Studio Color 575 User s Manual Addendum Selecting a Lens Wheel Position LENS 1 Using the lt Up gt and lt Down gt arrow buttons scroll to the LENS construct and press the lt Enter gt button to select the Litho wheel control construct n gt lt lt un Using the lt Up gt and lt Down gt arrow buttons scroll to the desired lens wheel position in this example D160 and press the lt Enter gt button to select the desired value Cc mM TJ N Selecting a Frost Wheel Position FRST EAGT 1 Using the lt Up gt and lt Down gt arrow buttons scroll to the FRST construct and press the lt Enter gt button to select the litho wheel position construct d 60 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the desired frost wheel position value in this example D160 and press the lt Enter gt button to select the desired value Setting an MSpeed Value MSPD 1 Using the lt Up g
31. lue of any of the individual presets listed above you must access each preset s corresponding menu item When you change any of the preset default values individually this menu item will automatically be turned off Changing the Control Method CHNL Use this menu item if your fixture is currently set to the fixture number control method and instead you want to use the DMX start channel control method or vice versa To simply change an existing fixture number to a different fixture number or DMX start channel to a different DMX start channel see Address Menu ADDR on page 5 To change the control method Adc 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the SET menu and press the SET lt Enter gt button to select the SET menu CHNE 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the CHNL menu and press the lt Enter gt button to select the CHNL menu 4 Using the lt Up gt and lt Down gt arrow buttons choose either the DMX option to address or the fixture using a DMX start channel or the ADDR option to address the fixture using a Addr fixture number Press the lt Enter gt button to select the desired option Note After changing the control method you must assign a specific DMX start channel C001 C512 or fixture number F 01 F xx to each fixture see Addr
32. menu allows you to change the control method from a fixture number to a DMX start channel or vice versa and either set all factory options to their default settings or change the factory options individually The procedures below are listed in the order that they appear in the menu map Setting Factory Defaults FACT Studio Color 575 fixtures are shipped from the factory with the following preset options set to the following defaults pan tilt swap off tilt invert off pan invert off LED display on LED display invert off shutdown 5 min To return all preset options to their factory defaults settings 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the SET menu and press the lt Enter gt button to select the SET menu Heid 1 Press and hold the lt Menu gt button until ADDR appears on the LED display fALT 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the FACT menu This will be the first menu displayed Press the lt Enter gt button to select the FACT menu page 13 Studio Color 575 User s Manual Addendum 4 Using the lt Up gt and lt Down gt arrow buttons choose ON to set the factory option defaults on and press the lt Enter gt button to select the desired option Note Although OFF is an available option in the FACT menu selecting the OFF option will have no effect on the individual preset values To change the va
33. ming Self Tests SELF This menu item performs the appropriate self tests for the following ALL performs all of the self tests listed below PAN tests the pan motor movement TILT tests the tilt motor movement COLR tests fixed color wheel movement MAGN tests magenta color wheel movement YELW tests yellow color wheel movement CYAN tests cyan color wheel movement LENS tests lens wheel movement FRST tests frost wheel movement SHUT tests strobe functions DIM tests dim flag movement To perform a self test an 4 Dj aa 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the TEST menu and press the lt Enter gt button to select the TEST menu 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the SELF menu and press the lt Enter gt button to select the SELF menu 4 Using the lt Up gt and lt Down gt arrow buttons scroll to the desired option listed above Press the lt Enter gt button to select the desired option The fixture will perform the selected self test 5 Press the lt Menu gt button to exit the test Note The self tests will run continuously until you press the lt Menu gt button to exit the test Copying the Boot Code BOOT When you upload new software to Studio Color 575 fixtures the new software may contain a new boot code which must be
34. n gt arrow buttons choose the ON option to strike the lamp the OFF option to extinguish the lamp or the STAT option to view the lamp status for information on lamp status options see Viewing the Lamp Status LAMP on page 6 Press the lt Enter gt button to select the desired option Testing the LED Display DISP To perform a self test on the LED display TEST ara gt 4 Note Press and hold the lt Menu gt button until ADDR appears on the LED display Using the lt Up gt and lt Down gt arrow buttons scroll to the TEST menu and press the lt Enter gt button to select the TEST menu Using the lt Up gt and lt Down gt arrow buttons scroll to the DISP option and press the lt Enter gt button to select the DISP option The LED will run through its self test Press the lt Menu gt button to exit the test The self test will run continuously until you press the lt Menu gt button to exit the test Mode Menu MODE The Mode menu allows you to set the fixture type to either Studio Spot 575 or Studio Color 575 and crossload software versions from one fixture to all other Studio Spot 575 or Studio Color 575 fixtures on the link The procedures below are listed in the order that they appear on the menu map Crossloading Fixture Software XLD Studio Color 575 Studio Spot 575 ES 1 and EC 1 fixtures with preset programming ability use the same software Therefore
35. nnel ranges when changing the fixture number DMX start channel Information Menu INFO The Information menu allows you to view current fixture information such as lamp status lamp hours lamp strikes software version total fixture hours internal temperature sensor information DMX errors and DMX data for any other device on the link You can also reset the lamp hours or fixture hours The procedures below are listed in the order that they appear on the menu map page 5 Studio Color 575 User s Manual Addendum Viewing the Lamp Status LAMP This menu option allows you to view the fixture s current lamp status To view the lamp status Addr 1 INFO LAMP gt Press and hold the lt Menu gt button until ADDR appears on the LED display Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the lt Enter gt button to select the INFO menu Using the lt Up gt and lt Down gt arrow buttons scroll to the LAMP option This will be the first option displayed Press the lt Enter gt button to select the LAMP option The LED will display L ON if the lamp is on LOFF if the lamp is off STRK if the lamp is attempting to strike or ERR if the lamp is experiencing an error Viewing the Current Lamp Hours L HR To view the number of hours the lamp has been on since this option was reset Addr 1 W HR 3 alla 0j
36. ogic board s current minimum and maximum temperatures This option also allows you to reset the minimum and maximum temperature readings To view the logic board temperatures Add 1 Press and hold the lt Menu gt button until ADDR appears on the LED display ThE 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the INFU lt Enter gt button to select the INFO menu TEMP 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the TEMP option and press the lt Enter gt button to select the TEMP option page 7 Studio Color 575 User s Manual Addendum 4 Using the lt Up gt and lt Down gt arrow buttons scroll to the CURR option to view the current temperature MINT to view the minimum temperature MAXT to view the maximum temperature or RST to reset the minimum and maximum temperature readings 5 Press the lt Enter gt button to select the desired option The LED will display the temperature CURR or MINT FAXT 7 of the fixture s logic board in degrees centigrade or The maximum temperature reading for the logic board is 99 C If this maximum temperature is exceeded the fixture will shut down and the LED panel will display OVER TEMP Viewing DMX Status and Construct Values FIXT This menu option allows you to view DMX status and construct values for the fixture You should follow this procedure if you ar
37. ogrammed 16 preset scene sequence erases i any preset scenes previously programmed Menu Options The sections below explain how to access the fixture options shown in the fixture s menu map For more information on preset programming see page 19 Address Menu ADDR Use the Address menu to quickly change the current fixture number DMX start channel Using this menu option you can only change the existing fixture number to another fixture number or the existing DMX start channel to another DMX start channel If you want to change the way you identify the fixture i e change to a fixture number instead of a DMX start channel or vice versa complete the procedure described in Setting the Fixture Shutdown Time S DN on page 16 To change the current fixture number or DMX start channel AddR 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Press the lt Enter gt button to select the ADDR menu 3 Use the lt Up gt and lt Down gt arrow buttons to select a new DMX start channel C001 C512 or fixture number F 01 F xx The LED display will flash when a new option is selected Ef fl 4 Press the lt Enter gt button to accept the new fixture number DMX start channel The LED display will stop flashing when a new option is entered If you do not press the lt Enter gt button the new option you selected will not be stored Note Be sure you do not overlap fixture cha
38. on was reset RST reset the fixture s minimum and maximum temperature values ERRS view the total number of DMX errors FE view the number of DMX framing errors INFO OV view the number of DMX overruns CE view the DMX checksum errors STRT view the DMX start code value PANH view the DMX high resolution pan value PANL view the DMX low resolution pan value TLTH view the DMX high resolution tilt value TLTL view the DMX low resolution tilt value DMX FIXT COLC view the DMX color control value a COL view the DMX fixed color wheel position value CYAN view the DMX cyan color wheel position value MAGN view the DMX magenta color wheel position value YELW view the DMX yellow color wheel position value LENS view the DMX lens wheel position value FRST view the DMX frost wheel position value SHUT view the DMX shutter strobe value DIM view the DMX shutter dim flag value MSPD view the DMX MSpeed time value CNTL view the DMX control channel value p n 60600138 v 1 0 Menu Menu Menu Menu Menu Description Level 1 Level 2 Level 3 Level 4 Level 5 FIXT CSUM view the DMX checksum value DMX Ibara 901 view the DMX data for the selected DMX channel C512 SENP view whether the pan sensor is obstructed OFF or is not obstructed ON SENT view whether the tilt sensor is obstructed OFF or
39. pecific lens wheel position on either the radium lenticular D357 or fibroid lens OPEN select the open no lens position on the frost wheel FRST D001 select a specific frost wheel position on either the frost lenticular or D355 fibroid lens NONE disable MSpeed and allow for DMX controller crossfade MSPD 0 15 select a motor movement time in decimal seconds from fast 0 15 252 7 to slow 252 7 9 se E select the DIM construct s crossfade time in increments of 0 1 XFAD ee select the DIM construct s crossfade time in increments of 1 S 7 select the scene delay time in increments of 0 1 DLAY D 10 D166 select the scene delay time in increments of 1 SEC select seconds as the units of time used for the XFAD and DLAY constructs select minutes as the units of time used for the XFAD and DLAY TIME MIN constructs HOUR select hours as the units of time used for the XFAD and DLAY constructs ZERO OK erase any programming of the current scene by voiding all construct values mark the end of the loop Studio Color 575 User s Manual Addendum page 4 Menu Menu Menu Menu Menu Describtion Level 1 Level 2 Level 3 Level 4 Level 5 P FROM we select a scene to copy from source scene F 16 COPY T01 r TO T16 select a scene to copy to destination scene PRST CAPT SN01 select a scene to capture a pre programmed scene to from your SN16 DMX controller DFLT OK enable the factory pr
40. press the lt Enter gt button to select the desired value Note The delay value determines the length of the scene If you want all motor transitions to be completed before the next scene begins XFAD must be less than or equal to DLAY If XFAD is longer than DLAY the transition will not be completed before the next scene begins Set the unit of time used for delay seconds minutes or hours using the TIME construct Studio Color 575 User s Manual Addendum page 22 Setting the Time Unit TIME TIME 1 Using the lt Up gt and lt Down gt arrow buttons scroll to the TIME construct and press the lt Enter gt button to select the time construct 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the desired time value in this example SEC and press the lt Enter gt button to select the desired value Note This construct sets the unit of time used in for the XFAD values Erasing the Scene ZERO 1 Using the lt Up gt and lt Down gt arrow buttons scroll to the ZERO construct and press the lt Enter gt button to select the zero construct 2 The LED will display OK In this example press the lt Menu gt button Pressing the lt Menu gt button will exit this construct and leave the current scene as programmed Pressing the lt Enter gt button will erase the scene and mark the end of a loop Creating a Loop A loop is a series of programmed scenes that continuously plays in sequ
41. reset scenes Aci 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the PRST menu and press the IAG lt Enter gt button to select the PRST menu CAPT 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the CAPT menu and press the lt Enter gt button to select the CAPT menu 4 Using the lt Up gt and lt Down gt arrow buttons scroll to the scene you want to copy the preset to scene to destination scene and press the lt Enter gt button GNIb Pressing the lt Enter gt button will copy the DMX 512 controller s preset scene to the selected scene on your fixture s on board 16 scene memory When the fixture finishes the capture successfully DONE will appear briefly in the fixture s LED display Note You must use the fixture s on board scene memory to manually select values for the XFAD DLAY and TIME constructs since a DMX controller will not transmit those construct values For more information on preset programming see Preset Programming on page 20 Enabling the Preset Default DFLT This menu item enables the factory programmed 16 preset sequence or fixture self demo Enabling this menu item will erase any pre programmed scenes or construct values on your fixture s on board memory To enable the self demo AddR 1 Press and hold the lt Menu gt button until
42. row buttons scroll to the FIXT menu and press the lt Enter gt button to select the FIXT menu u gt lt DA 5 Using the lt Up gt and lt Down gt arrow buttons scroll to the desired DMX status or construct listed above and press the lt Enter gt button to select the desired option The LED will display the selected DMX status or construct value Studio Color 575 User s Manual Addendum page 8 If you are having a particular problem with the fixture follow the steps above to select a construct and view its value After noting the value of the construct you selected use your controller to change that construct s value If the value changes on the fixture s LED display but the fixture still does not respond contact High End Systems customer service However if the value does not change on the fixture s LED display remove the fixture from the DMX link and try to change the construct s value using the fixture s menu system If the fixture then functions normally the problem was likely with the DMX link Otherwise contact High End Systems customer service Viewing DMX Data for Another Device DATA This procedure allows you to use a Studio Spot 575 or Studio Color 575 fixture to view DMX channel values for other devices on the DMX link You should use this procedure either for testing devices that do not have built in DMX diagnostics or for fixtures that are physically inconvenient to monitor direc
43. s scroll to the TEST menu and press the lt Enter gt button to select the TEST menu Using the lt Up gt and lt Down gt arrow buttons scroll to the HOME option This will be the first option displayed Press the lt Enter gt button to select the HOME option The LED will alternately display RST and HOME while the fixture homes Placing the Fixture in Setup Mode S UP This menu item allows you to place the fixture in setup mode so that you can mechanically home your fixture A fixture that is out of home i e the dim flags lose position will emit an unusually loud clicking noise when strobing or electronically homing For more information on how to mechanically home the fixture contact High End Systems customer service To place the fixture in setup mode Add 1 Press and hold the lt Menu gt button until ADDR appears on the LED display Studio Color 575 User s Manual Addendum page 10 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the TEST menu and press the lt Enter gt button to select the TEST menu 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the S UP option and press the lt Enter gt button to select the S UP option 4 When the LED displays SET NOW mechanically home the fixture After mechanically homing the fixture press any button This causes the fixture to electronically home Perfor
44. t and lt Down gt arrow buttons scroll to the MSPD construct and press the lt Enter gt button to select the MSpeed construct N zz ale za oo wn Using the lt Up gt and lt Down gt arrow buttons scroll to the desired MSpeed in this example 1 5 in decimal seconds and press the lt Enter gt button to select the desired value In this example the MSpeed value only affects the pan and tilt constructs because the pan and tilt values default to MSpeed time and no other constructs with MSpeed values were chosen Setting a Crossfade Value XFAD XFA 1 Using the lt Up gt and lt Down gt arrow buttons scroll to the XFAD construct and press the lt Enter gt button to select the crossfade construct XG 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the desired crossfade value in increments of 0 1 or 1 in this example 1 5 and press the lt Enter gt button to select the desired value Note The crossfade value affects the DIM construct Set the unit of time used for crossfade seconds minutes or hours using the TIME construct Setting a Delay Value DLAY dLAY L Using the lt Up gt and lt Down gt arrow buttons scroll to the DLAY construct and press the lt Enter gt button to select the delay construct aen 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the desired delay value in increments of 0 1 or 1 in this example 6 0 and
45. t button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the SET menu and press the lt Enter gt button to select the SET menu d IN 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the D IN menu and press the lt Enter gt button to select the D IN menu 4 Using the lt Up gt and lt Down gt arrow buttons choose the ON option to invert the fixture s alphanumeric characters or the OFF option to return the fixture s alphanumeric characters to normal orientation Press the lt Enter gt button to select the desired option Inverting Pan P IN To invert the direction of the fixture s pan motion Aedcdfe 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the SET menu and press the lt Enter gt button to select the SET menu F T 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the P IN menu and press the lt Enter gt button to select the P IN menu 4 Using the lt Up gt and lt Down gt arrow buttons choose the ON option to invert the fixture s pan motion or the OFF option to return the fixture s pan motion to normal orientation Press the lt Enter gt button to select the desired option Inverting Tilt T IN To invert the direction of the fixtur
46. t Enter gt button to select the SET menu AMPI 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the LAMP menu and press the lt Enter gt button to select the LAMP menu 3 4 Using the lt Up gt and lt Down gt arrow buttons choose the ON option to strike the lamp the OFF option to extinguish the lamp 5 Press the lt Enter gt button to select the desired option Copying the Boot Code BOOT When you upload new software to Studio Color 575 fixtures the new software may contain a new boot code which must be copied to each fixture This is apparent if the LED displays a BOOT DIFF error Do not remove power from the fixture while performing a boot copy You can copy the new boot code using either the TEST menu or the SET menu To accept and store the new boot code using the SET menu Adc 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the SET menu and press the lt Enter gt button to select the SET menu bUOT 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the BOOT option and press the lt Enter gt button to select the BOOT option The fixture will store the new boot code then automatically home Studio Color 575 User s Manual Addendum page 16 Preset Menu PRST The Preset menu allows you to turn preset playback o
47. tly To view DMX data for another device on the DMX link Ae 1 Press and hold the lt Menu gt button until ADDR appears on the LED display NEG 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the INFO menu and press the lt Enter gt button to select the INFO menu JMX 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the DMX menu and press the lt Enter gt button to select the DMX menu JATA 4 Using the lt Up gt and lt Down gt arrow buttons scroll to the DATA menu and press the lt Enter gt button to select the DATA menu 5 Using the lt Up gt and lt Down gt arrow buttons scroll to the desired DMX channel C001 to C512 and press the lt Enter gt button to select the desired DMX channel The LED will TAF display the selected channel s DMX value If you are experiencing a particular problem with a device on the link follow the steps above to select a DMX channel in the device s channel range and view its DMX value After noting the value of the channel you selected use your controller to change that channel s value If the value of the DMX channel you selected does not change there may be a problem with the DMX cable or your transmitting device i e controller However if the DMX channel value changes but the device does not respond the device may be faulty Consult the documentation provided with that device for more information V
48. utton to select the desired option Setting the Fixture Shutdown Time S DN Use this menu item to set the fixture to automatically shutdown or deactivate either 5 or 10 minutes after DMX data is removed When a fixture is in shutdown mode the lamp is extinguished power to the motors is disabled and the LED display is turned off Once a fixture is in shutdown mode you must home the fixture to bring it back into operation To set fixture shutdown Acid 1 Press and hold the lt Menu gt button until ADDR appears on the LED display Ger 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the SET menu and press the J lt Enter gt button to select the SET menu 3 Using the lt Up gt and lt Down gt arrow buttons scroll to the S DN menu and press the lt Enter gt button to select the S DN menu 4 Using the lt Up gt and lt Down gt arrow buttons choose the 5 MN option to enable shutdown after 5 minutes or the IOMN option to enable shutdown after 10 minutes Press the lt Enter gt button to select the desired option Turning the Lamp On or Off LAMP You can manually turn the lamp on and off using either the TEST menu or the SET menu To turn the lamp on or off via the SET menu Heidt 1 Press and hold the lt Menu gt button until ADDR appears on the LED display 2 Using the lt Up gt and lt Down gt arrow buttons scroll to the SET menu and press the l
Download Pdf Manuals
Related Search