manual_srp-340_ig_eng_rev.1.1 (USA)
Contents
1. 7 8F Sampyeong dong 20 Pangyoyeok ro241beon gil Bundang gu Seongnam si Gyeonggi do 463 400 Korea ROK Tel 82 31 218 5500 e US Office Add BIXOLON America Inc 3171 Fujita St Torrance CA 90505 Tel 1 858 764 4580 e Europe Office Add BIXOLON Europe GmbH Tiefenbroicher Weg 35 40472 D sseldorf Tel 49 0 211 68 78 5402. released 1 Serial Interface DIP Switch 1 OFF l 5 Parity Selection EVEN _ _ ODD OF OFF Baud rate Selection bps Refer to the following Table 1 e DIP Switch 2 24 Reserved OFF Print Density Refer to the following table 2 Near End Sensor Status 2 Parallel USB Interface External buzzer External buzzer enable e DIP Switch 1 disable 1 2 Reseved J o o o S oo OS O 13 Reseved o o o S oo y OS O 14 Reseved o o oo S oo O O iS f Reseved J o o o S oo y OOS O 1 6 Reseved CFF 1 7 Reseved J o o S o y y OS No OFF 2 8 External buzzer control 18 Reserved e DIP Switch 2 24 Reserved CFF OFF Near End Sensor Status 2 8 Eeenoi huner conio External buzzer External buzzer enable disable e Table 1 Baud Rate bps Selection 9600 e Table 2 Print Density Selection 2 Medium 3 Dark Self Test 1 Make sure the paper roll has been installed properly 2 Turn on the power while holding down the FEED button The self test begins 3 The self test prints the current printer status providing the control ROM version and the DIP switch setting 4 After printing the current printer status self test printing will print the following and pause The PAPER LED light blinks SELF TEST PRINTING PLEASE PRESS THE FEED BUTTON 5 Press the FEED button to continue printing The printer prints a pattern using th
3. printer off and on and click the OK button SRP340_ Installer Please turn off the printer and then turn on again 5 After restarting the computer select Start gt Settings gt Printers and Faxes gt BIXOLON SRP 340 Icon gt Right Mouse Click gt Properties 6 Select General tab from the Properties window and select Print Test Page to check whether printer setup has been done correctly Installing Windows Driver for the Printer with Ethernet Interface Refer to the separate Ethernet Interface Card User s Manual Refer to CD WEEE Waste Electrical and Electric Equipment This marking shown on the product or its literature indicates that is should not be ps disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal EE please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal BIXOLON Co Ltd e Website http www bixolon com e Korea Headquarters Add
4. BIXOLON Printer Installation Guide KN04 00068A Rev 1 1 Information This Installation Guide includes a brief outline of information necessary for product installation For more detailed installation information please refer to the user manual in the enclosed CD The contents of the CD include the following 1 Manual User Manual Code Chart Control Commands 2 Drivers Windows Drivers OPOS Drivers 3 Utilities a logo download tool We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality of all our products In following product specifications and or user manual content may be changed without prior notice Components AC DC Adaptor Installation Guide Power Cord Connecting the Cables 1 Turn off the printer and the host ECR host computer 2 Plug the power cord into the Adaptor and then plug the Adaptor into the power connector of the printer 3 Check the interface cable Serial Parallel USB or Ethernet and connect the interface connector cable accordingly 4 Plug the drawer kick out cable into the drawer kick out connector on the printer X Do not use an adapter that was not supplied with the printer Drawer kick out connector Power connector Adaptor Drawer kick out cable Interface connector Interface cable Serial Parallel USB Ethernet Power cord Installing the Paper Roll 1 Open the paper roll cover by pressing the cover o
5. e built in character set 6 The self test automatically ends and cuts the paper after printing the following COMPLETED 7 After the self test is complete the printer returns to normal on line status X Note The self test lets you know if your printer is operating properly It checks the print quality ROM version and DIP switch settings Specifications 42 Font A 56 Font B 56 Font C Printing Speed 1 BS a eater 0 45 T Operatin 10 80 RH Operating 10 90 RH Storage Except for paper os Inner 012mm 0 47 Outer 18mm 0 71 Characters per line default Humidity Paper Tube X Note Printing speed may be slower depending on the data transmission speed and the combination of control commands 2 The above values are calculated under printing level 2 with recommended paper at normal temperature The values may vary with environment temperature printing level etc Installing Windows Driver for the Printer with Serial RS 232C Interface 1 Run Win SRP 340_Vx x x exe 2 Select the Next button from the initial installation window 3 Select one of serial port in Serial Port section from the Port Type window and select the Next button Port Type Parallel Port LPT1 LPT2 Serial Port USB Port f COM3 C COM4 USB f COM2 Fig 1 4 Select Yes and restart the computer SRP 340 Installer Restarting your computer can take effect Please r
6. estart your computer Yes I wank to restart my computer now Mo I will restart my computer later Yes Mo Fig 2 5 After restarting the computer select Start Menu gt Settings gt Printers and Faxes gt BIXOLON SRP 340 icon gt Right Mouse Click gt Properties 6 Select the Port tab and Port Settings from the Properties windows set the parameters reported from the self test result and select the OK button COM1 Properties Port Settings Bits per second yell v Data bits Parity Stop bits Flow control Hardware Restore Defaults Installing Windows Driver for the Printer with Parallel EEE1284 Interface 1 Run Win SRP 340_Vx x x exe 2 Select the Next button from initial installation window 3 Select one from Parallel Port section of the Port Type window and select the Next button refer to Fig 1 4 Select Yes and restart the computer refer to Fig 2 5 After restarting the computer select Start gt Settings gt Printers and Faxes gt BIXOLON SRP 340 Icon gt Right Mouse Click gt Properties 6 Select General tab from the Properties window and select Print Test Page to check whether printer setup has been done correctly Installing Windows Driver for the Printer with USB Interface 1 Run Win SRP 340_Vx x x exe 2 Select the Next button from initial installation window 3 Select USB from the Port Type window and select the Next button refer to Fig 1 4 Turn the
7. pen button 2 Insert a new paper roll making sure to align it properly 3 Pull out a small amount of paper and close the cover X Note When closing the cover press down on the center of the cover to ensure that the paper is in contact with the roller Printing quality may not be optimum if recommended paper is not used Refer to the User s Manual X Note Adjusting the Paper Near End Sensor The SRP 340 has a paper near end sensor that provides notice that the paper roll is nearly exhausted When the paper is running low the lamp on the apparatus is lit red If the lamp is activated even when sufficient paper remains adjust the near end sensor setting by pushing the tab upward towards1 THERMAL PRINTER Using the Operation Panel e POWER LED When turning on the power a green LED will be lit SRP 340 Power e ERROR LED When an error occurs a red LED will be lit Error O e g no paper cover ajar etc Paper PAPER LED O Red LED will be lit when the paper roll is running low The LED blinks when the printer is in self test standby mode or macro execution Feed standby mode e FEED Button Setting the Dip Switches Changing Dip Switch settings must be done when the printer is off Any changes done while the printer is on will not be processed Press the FEED button once to discharge extra paper Holding down the FEED button will discharge paper continuously until the button is
Download Pdf Manuals
Related Search