TA+P2I - Stollmann
Contents
1. ISDN phone ISDN phone To use the TA P21 with an ISDN PABX please do the steps below e Connect the power supply to the TA P2I and mains The green LED READY at the front panel will be lit permanently Attention Please use only the delivered power supply e Connect LINE 1 with the first analogue line LINE 2 with the second one The corresponding LEDs LINE1 and LINE2 will be lit green e Connect the public line port of the PABX to one ISDN plug Note The ISDN terminating resistors for the ISDN network are integrated inside the TA P2I already Release r06 www stollmann de Page 7 of 18 TA P21 User Manual S Im n e For accepting incoming calls with the correct calling number you have to set up the MSN inside the ISDN PABX Set up the MSN of your ISDN PABX as they are signaled by the TA P21 By default the MSN 1 for the analogue line 1 and the MSN 2 for the analogue line 2 2 4 Displays 4 Q y V N V SS SF S amp sS S PG OS Y amp H 47 4 F CO JO OJ JAKO READY ERROR LINE1 LINE ISDN1 ISDN2 CONF EXT Release r06 The TA P2I is powered and ready to use Hardware error the TA P2I cannot be used Lit The analogue line 1 is connected to a working analogue interface Blinking The analogue line 1 is connected to a working analogue interface but there is no dial tone Lit The analogue line 2 is connected to a working analogue int2. st6 mann Manual Function TA P2I Power supply External plug in power supply Input 100 240V AC Output 12V DC 1 25A Dimensions 127 x 88 x 27 mm CE conformity CE Europe 7 1 Analogue ports Function TA P2I Plug 2 x RJ11 Ringing detection 20 to 50 Hz Off Hook On Hook signaling V DTMF dial Barring incoming call y CLIP detection FSK Busy tone detection N Pin assignment analogue plug 6 pin RJ11 Pin Signal a b Not connected Not connected a TIP b RING Not connected Not connected CE 7 2 ISDN ports Function TA P2I ISDN interface 1 x 1 430 LT S mode S Bus BRI Plug 2 x RJ 45 Terminating resistors Integrated 2 x 100 Ohm Phantom feeding ISDN Bus 4 Watt Supplementary services TA P21 MSN DDI call waiting hold resume three party conference call forwarding Supplementary services transparent using DTMF All available on analogue line D channel protocol DSS1 LT S mode Interfacing modes Multipoint B channel G 711 a law analogue voice Configuration Block dial via ISDN phone Release r06 www stollmann de Page 16 of 18 TA P21 User Manual S Im n Pin assignment ISDN plug 8 pin RJ45 ITU 1 430 ISO 8877 Fin soas 2a Rx Receive 1a Tx Transmit 1b Tx Transmit 6 2b Rx Receive 8 Notconnected gt Release r06 www
3. rrrrrrnnnrennnrrnnnnrennnrrnnnrrennnrennnrrennnr 7 20 DEI SN 8 25 Med 9 gt VETT PN 9 31 1800 aa 6 0 EEE 10 See MOU OI CAN EE EE 11 3 3 MN 11 JA CAMO ENGU EE 11 3 9 Three party Nag 12 236 TI 12 3 7 Additional supplementary services 12 T 0 DAJMO SG en E R 13 4 1 Error Phone calls not possible rrrrrnrrrnnrvnrrvnrrnnnrvnrrnnrrnnrrnnrrnnernnernnrennsennee 13 4 2 Error No dial 0 EEE 14 4 3 Error No incoming calls 14 17 FOU 14 5 EN asacsexeseceseeo E E E ne cn coude 15 5 1 Overview configuration commands rrnrrnnnrrnnnevnnrrvarrvnnnrvnrnranernnrernrennnsennn 15 6 ENN 15 7 echnical 00 SSP 16 Tcl FAMAIOGUC DONS EEE 16 T2 IODNDONG sees a 16 8 PISTO PE EN et he ent een an 18 Release r06 www stollmann de Page 3 of 18 TA P21 User Manual S Im n 1 Introduction We are very pleased to see that you have purchased a Stollmann product and would like to express our appreciation This documentation is valid for the product TA P2l e Software version V1 715 or later 1 1 Product description Using the TA P2I you can connect ISDN phones or an ISDN PABX with two analogue interfaces POTS FXS The analogue lines of the TA P2I react like standard analogue phones und have to be connected with the FXO ports of the switching system or adapter The ISDN interface has identical function equal to an ISDN interface presented by an NT1 or a PABX You can connect u
4. 1 is connected to a working analogue interface but there is no dial tone If not please check the connection between the plug LINE2 and the analogue port The analogue line 2 is connected to a working analogue interface but there is no dial tone Check the setting of the MSNs in the ISDN phone and the TA P2l In the default configuration of the TA P2I MSN 1 is configured for analogue line 1 and MSN 2 is configured for analogue line 2 Please check if the ISDN phone is configured accordingly i e MSN A 1 Page 13 of 18 4 2 Error No dial tone ISDN1 or ISDN2 lit but there is no dial tone 4 3 Error No incoming calls Is the setting of the MSN correct 4 4 FAQ TA P21 User Manual S Im n The analogue line is connected to a working analogue interface but there is no dial tone Please check in the customer portal of Kabel Deutschland if a phone number is activated at the analogue line Another phone already uses the same analogue line Check if a busy tone can be heard and or the phone display indicates that the line is busy Check the setting of the MSN in the ISDN phone and the TA P2I Please refer additionally to chapter incoming call e The TA P2I supports all ISDN phones and ISDN PABX s configured to multipoint mode e The TA P2I does not support data connections via ISDN modems or ISDN PC cards Voice connections like answering machine and fax G3 are supported e Call
5. the voice connection via VolP An example of an outgoing call attempt using the key looks like follows lt phone number gt i e 123456789 Important Some ISDN phones do not support or it is disabled by default dialing using key in the dial string Please refer to the user manual of your ISDN phone to change this setting To make an outgoing call with calling line restriction please use the menu user interface of the ISDN phone The signaling sequence will be adapted automatically by the TA P2l Note The ISDN phone can display connected although the connection has not been established completely This behavior is caused by the technology 3 3 Call waiting Call waiting will be signaled as if connected to an ISDN network The display text and tone signaled is dependent on the configuration of the ISDN phone and will be shown according to the ISDN phone features and settings typical by an acoustic tone and a display entry 3 4 Call Hold Enquiry You can start an enquiry by the typical sequence as usual for the ISDN phone menu key or R key Release r06 www stollmann de Page 11 of 18 TA P21 User Manual S Im n 3 5 Three party conference You can start a three party conference by the typical sequence as usual for the ISDN phone menu driven 3 6 Call forwarding You can activate and deactivate call forwarding by the typical sequence as usual for an analogue line by prefix codes These codes are predef
6. d inside the TA P2I already e Check whether you can receive calls using all called numbers If you have problems please proceed as follows o If one ISDN phone shall react on all incoming calls from both lines it is necessary to delete all still activated MSN settings inside the ISDN phone o If one ISDN phone shall react only to the phone numbers of one of the analogue lines of the cable modem change the former MSN settings and use the digit 1 as MSN for that phone which shall react on incoming call from line 1 Please handle the same way for the ISDN phone that shall be allocated to line 2 this phone needs the digit 2 as MSN setting o Example For line 1 was associated the call number 123123123 and for line 2 the call number 456456456 lf an ISDN phone shall only accept incoming calls for the number 123123123 set up the MSN of this phone to 1 f another phone shall react on incoming calls to 456456456 set up the MSN of this phone to 2 lf athird phone shall react on all incoming calls so delete all MSNs of that phone e More information you can find in your phone manual If you have problems setting up MSNs please contact your dealer or the manufacturer of the phone More setups you will find in the next chapter Release r06 www stollmann de Page 6 of 18 TA P21 User Manual S Im n 2 3 Procedure of Installation for ISDN PABX Cablemodem TA P2I
7. d analogue line please dial instead 00000102xxx Set the first MSN for analogue line 2 to xxx factory default 2 Dialing 000001022 Two additional MSNs can be programmed for each line accordingly by using other dial codes see chapter configuration Note The settings can only be changed by using an ISDN phone directly connected to the TA P21 Changing the settings via a ISDN PABX are not possible because the configuration command IS not transmitted to the TA P2I Release r06 www stollmann de Page 10 of 18 TA P21 User Manual S Im n 3 2 Outgoing call An outgoing call will be started identical as if the ISDN phone would be connected directly to the ISDN network via the menu and the keys of the ISDN phone The MSNs entered in the ISDN phone and the TA P2I define the analogue interface line 1 or line 2 that will be used for the outgoing call If no MSN is defined in the ISDN phone the TA P2I uses the next free analogue line line 1 or line 2 If a wrong MSN a MSN which does not match with any MSN configured in the TA P21 is configured in the ISDN phone an outgoing call is not possible In case that during an outgoing call an assumed call pause of approx 10 seconds occur this can be reduced to approx 5 seconds by terminating the call attempt with the key Background The assumed call pause is caused by the analogue interface DTMF tones are not hearable via ISDN and the cable modem The cable modem establishes
8. erface Blinking The analogue line 2 is connected to a working analogue interface but there is no dial tone The first B channel is in use respectively the hand set of the ISDN phone is off hook The second B channel is in use respectively the hand set of the ISDN phone is off hook The configuration of the TA P2I has been changed Reserved www stollmann de Page 8 of 18 2 5 TA P21 User Manual S Im n Interfaces PWR ISDN S0 ISDN SO LINE2 LINE1 LINE1 Interface for the first analogue line LINE2 Interface for the second analogue line ISDN SO First plug for ISDN devices ISDN SO Second plug for ISDN devices PWR Interface for external power supply Attention Please use only the delivered power supply 3 Usage of the TA P2I By adapting with the TA P2I you can use many supplementary services known from the ISDN also via the analogue lines the services have to be activated on the analogue lines The TA P2I supports the following supplementary services Outgoing call including transmission of calling party number Calling line identification restriction Incoming call including display of calling party Call waiting Call hold Three party conference 3PTY Barring incoming calls Terminal portability TP Call forwarding CFU CFB CFNR More services may be available depending on the characteristics of the analogue lines these can be driven from the ISDN phone transparently by key inputs Release r06 ww
9. ined by your service provider Activation and deactivation is only possible by using the appropriate keys of the ISDN phone i e 21 lt phone number gt Activation and deactivation by using the menu keys of an ISDN phone or an ISDN PABX is not possible 3 7 Additional supplementary services Additional services like call completion to busy subscriber call transfer etc are not available via the menu driven interface of the ISDN phone These services are defined by the services of the analogue lines and are controlled by keypad input DTMF tones The display information of the ISDN phone is also not available Please refer to the services supported by your provider of the analogue lines Release r06 www stollmann de Page 12 of 18 TA P2I User Manual 4 Error Diagnostic 4 1 Is the READY LED lit green Is the LINE1 LED lit green Is the LINE1 LED blinking green Is the LINE2 LED lit green Is the LINE2 LED blinking green Is the MSN programmed in the ISDN phone also programmed in the TA P21 Release r06 Error Phone calls not possible www stollmann de st6 mann If not please check whether the delivered power supply is adapted correctly Disconnect the power supply for several seconds Is the READY LED still off or is the ERROR LED lit the device has a hardware error Please contact your supplier If not please check the connection between the plug LINE1 and the analogue port The analogue line
10. p to 8 ISDN phones to the ISDN interface whereas up to 4 ISDN phones can be powered by the TA P21 ISDN modems for data transmission and ISDN fax machine group 4 cannot be driven by the TA P2l Devices based on voice connection like answering machines and fax G3 machines are supported Release r06 www stollmann de Page 4 of 18 2 TA P21 User Manual S Ilm n Installation 2 1 Content This package contains the following parts TA P2I adapter External power supply cable length approx 1 85m Two cable for the analogue interfaces cable length approx 1 00m This user manual Quick installation guide 2 2 Procedure of Installation for ISDN phones Cablemodem TA P2I ower supplry Power supplry ISDN phone ISDN phone Release r06 www stollmann de Page 5 of 18 TA P21 User Manual S Im n The installation of your TA P2I is done in a few simple steps e Connect the power supply to the TA P2I and mains The green LED READY at the front panel will be lit Attention Please use only the delivered power supply e Connect LINE 1 with the first analogue line of the cable modem LINE 2 with the second one The corresponding LEDs LINE1 and LINE2 will be lit green e Connect the ISDN phone s to one or both ISDN plugs As an alternative you can connect the previous installed ISDN cabling to one of the ISDN plugs Note The ISDN terminating resistors for the ISDN network are integrate
11. ry or other requirements in other environments No representation can be made and no warranty can be assumed regarding the suitability of the device for a specific purpose as defined by our customers Stollmann reserves the right to make changes to the hardware or firmware or to the specifications without prior notice or to replace the device with a successor model Of course any changes to the hardware or firmware of any devices for which we have entered into a supply agreement with our customers will be made only if and only to the extent that such changes can reasonably be expected to be acceptable to our customers No general commitment will be made regarding periods of availability these must be subject to individual agreement All agreements are subject to our Terms and Conditions for Deliveries and Payments a copy of which is available from Stollmann Copyright 2005 2008 Stollmann E V GmbH Trademarks The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by Stollmann E V GmbH is under license Other trademarks and trade names are those of their respective owners Release r06 www stollmann de Page 2 of 18 TA P2I User Manual Table of contents I NTO LOS E E 4 1 1 Product description 4 2 SPAN AON EEE EEE EE D 21 0 101 EEE EEE EE 5 2 2 Procedure of Installation for ISDN phones rrrnrennnrnrnnrnnnnennnrnranennnrennnennnre 5 2 3 Procedure of Installation for ISDN PABX
12. sigfisann TA P2I Adapting ISDN Phones to POTS FXS User Manual Release r06 TA P21 User Manual S Im n Note This device was developed for the purpose of communication in an office environment It is intended solely for our industrial clients for physical integration into their own technical products after careful examination by experienced technical personnel for its suitability for the intended purpose The device was not developed for or intended for use in any specific customer application The firmware of the device may have to be adapted to the specific intended modalities of use or even replaced by other firmware in order to ensure flawless function in the respective areas of application Performance data range power requirements etc may depend on the operating environment the area of application the configuration and method of control as well as on other conditions of use these may deviate from the technical specifications the Design Guide specifications or other product documentation The actual performance characteristics can be determined only by measurements subsequent to integration Variations in the performance data of mass produced devices may occur due to individual differences between such devices Device samples were tested in a reference environment for compliance with the legal requirements applicable to the reference environment No representation is made regarding the compliance with legal regulato
13. stollmann de Page 17 of 18 TA P21 User Manual S Im n 8 History Release Date Change description Nov 2007 First release for firmware version 1 701 r05 Mar 2008 nh New document structure Added pin assignment for analogue ISDN plug Changes for new firmware version 1 715 Modified behavior depending on the MSN settings during outgoing call New parameter for setting the year Modified LED behavior for LINE 1 LINE2 ISDN1 ISDN2 Jun 2008 Revised chapter Call Forwarding In case of technical problems or if you have questions about the installation please contact our service hotline under 01805 91 31 09 The service is available Monday Sunday between 8 00 am and 12 00 pm 14ct minute in German telephone network Different costs may occur when calling from mobile phone Release r06 www stollmann de Page 18 of 18
14. w stollmann de Page 9 of 18 TA P21 User Manual S Im n 3 1 Incoming call An incoming call will be shown via the ringing tone and the calling number display as if the ISDN phone would be connected to the ISDN network directly To route the incoming calls to the addressed ISDN phones it is necessary to set up the MSN of each ISDN phone If the MSN is not configured MSN lt empty gt in the ISDN phone the ISDN phone is ringing on incoming calls both on analogue line 1 and analogue line 2 If a wrong MSN a MSN which does not match with any MSN configured in the TA P2l is configured in the ISDN phone the ISDN phone is not ringing By factory the associated MSNs for the two analogue line are set to 1 line1 and 2 line2 For using the factory setting set up the MSN of your phones accordingly Phone with MSN 1 Is ringing on incoming calls on analogue line 1 Phone with MSN 2 is ringing on incoming calls on analogue line 2 For experts only lf a phone number according to the call number of the analogue lines shall be used you have to set up this correct MSN both in the TA P2I and the ISDN phones To change the setting for the MSN for analogue line 1 please do the following e Please enter the following number in on hook state of the ISDN phone e 00000101xxx Set the first MSN for analogue line 1 to xxx factory default 1 Dialing 000001011 e Go off hook e Goon hook Please proceed adequate for the secon
15. waiting Due to technical reason another phone in the same phone number group is ringing in case of call waiting But it is not possible to accept the waiting call with this phone only the active phone may accept the waiting call e For additionally frequently asked questions please refer to our web site http www stollmann de Release r06 www stollmann de Page 14 of 18 TA P21 User Manual S Im n 5 Configuration 5 1 Overview configuration commands Each configuration command has to be dialed en bloc from the ISDN phone Enter the configuration dial number go off hook and go on hook 00000101xxx Set up first MSN xxx for line 1 00000111xxx Set up second MSN xxx for line 1 00000121xxx Set up third MSN xxx for line 1 00000102xxx Set up first MSN xxx for line 2 00000112xxx Set up second MSN xxx for line 2 00000122xxx Set up third MSN xxx for line 2 The MSN xxx may consist of 1 20 digits 000002011 Barring incoming calls for line 1 000002021 Barring incoming calls for line 2 000002010 Release barring of incoming calls for line 1 000002020 Release barring of incoming calls for line 2 00000103ddmmyyhhmm Set up date and time 00000104yy Set up year only dd day mm month yy year hh hour mm minute 00000980 Reset all parameters to factory default 6 Operation Mode The TA P2I can only be used in multipoint operation mode Release r06 www stollmann de Page 15 of 18 TA P21 User 7 Technical features
Download Pdf Manuals
Related Search