SP-RANGE INSTALLATION AND OPERATING MANUAL PLEASE
Contents
1. SP12 SP25 Item Part No Description Part No Description 1 E58 117 Mounting Bracket 58 117 Mounting Bracket 2 E58 119 Wall Bracket E58 119 Wall Bracket 3 G76 041 1 Control Box inc lid G76 041 M1 Control Box inc lid 4 D21 097 Screw M4 x 8 Pan SS D21 097 Screw x 8 Pan SS 5 E58 118 Control Box Plate E58 118 Control Box Plate 6 A10 224 Cable Gland Nut A10 224 Cable Gland Nut 7 G80 029 Cable Gland G80 029 Cable Gland 8 D25 004 5 Shakeproof Washer D25 004 5 Shakeproof Washer 9 D20 038 M5 Full Nut SS D20 038 M5 Full Nut SS 10 G30 316 Contactor 400V 3ph G30 316 Contactor 400V 3ph 11 D22 022 Screw No8 D22 022 Screw No8 x 12 12 G30 318 Overload 3ph G30 299 Overload 3ph 13 G34AL Timer G34AL Timer 14 A11 219 Timer Gasket A11 219 Timer Gasket 15 D25 066 M3 Seloc Washer D25 066 M3 Seloc Washer 16 D21 031 Screw M3 x 8 Pan SS D21 031 Screw M3 x 8 Pan SS 17 G45 066 Timer Knob G45 066 Timer Knob 18 G45 099 Green Push Button G45 099 Green Push Button 19 G45 100 Red Push Button G45 100 Red Push Button 20 G45 102 Selector Switch G45 102 Selector Switch G60 371 Mains supply cable 3ph G60 371 Mains supply cable 3ph G60 373 Motor cable 3ph G60 373 Motor cable 3ph When ordering spare parts or accessories always quote the SERIES AND SERIAL NUMBER of the machine found on the rating label2. SP12 SP25 Item Part No Description Part No Description 1 E58 096 Mounting Bracket E58 096 Mounting Bracket E58 097 Wall Bracket Not shown E58 097 Wall Bracket Not shown 2 G76 031 M2 Control Box G76 031 M2 Control Box 3 D21 052 Screw M6 x 16 Pan SS D21 052 Screw M6 x 16 Pan SS 4 A08 641 Decal A08 641 Decal 5 E58 116 Control Box Plate E58 116 Control Box Plate 6 G30 431 M1 Programmed Inverter 0 75kW G30 431 M2 Programmed Inverter 0 75kW Schneider Schneider 7 D25 033 M4 Shakeproof Washer SS D25 033 M4 Shakeproof Washer SS 8 D21 038 Screw M4 x 12 PanSS D21 038 Screw M4 x 12 Pan SS 9 A10 224 Cable Gland Nut A10 224 Cable Gland Nut 10 G80 029 Cable Gland G80 029 Cable Gland 11 G60 372 Motor cable 1ph G60 372 Motor cable 1ph 12 G60 370 M2 Mains cable and plug ph G60 370 M2 Mains cable and plug ph 13 G34AL Timer G34AL Timer 14 A11 219 Timer Gasket A11 219 Timer Gasket 15 D25 066 M3 Seloc Washer D25 066 M3 Seloc Washer 16 D21 031 Screw M3 x 8 Pan SS D21 031 Screw M3 x 8 Pan SS 17 G45 066 Timer Knob G45 066 Timer Knob 18 19 G45 113 Push Button Black G45 113 Push Button Black 20 G45 114 Selector Switch G45 114 Selector Switch 21 G45 111 Button contacts and holder G45 111 Button contacts and holder When ordering spare parts or accessories always quote the SERIES AND SERIAL NUMBER of the machine found on the rating label SP Range 3PH CONTROL BOX SPARE PARTS LIST
3. 1 DELIVERY TE 1 SAMPLE RATING LABEL oo iii a 1 INTRODUCTION puce cu 2 me 2 CONTROLS 9 3 IRE EE rq o Ma 3 WATER SUPPLY oot Side n petis tae eode lu ceste idc ua 4 WASTE OUTLET CONNECTION eese esee ee eeeee nennen enne nante anna annt 4 WASTE EJECTOR eds 5 Fitting the Waste 8Jecltor obici co bio rtr ierra che mae 5 Waste Ejector adjustments ee 5 ELECTRICITY SUPPLY CONNECTION ee 6 COMMISSIONIN jet E ER 7 OPERATION Mer 7 70 TAY ai 8 CLEANING T P 8 DOS AND DON T9 2 epea NN REOR I ER AM NIE 9 MATERIAE CONTENT aaa 9 MAINTENANGE 10 ORDERING SPARE PARTS ee 10 WIRING DIAGRAM 1PH UNITS ee 11 WIRING DIAGRAM 3PH 6 12 PARTS ILLUSTRATION 13 SPARES PART EIS T 2 a 14 CONTROL BOX SPARE PARTS LIST 15 3PH CONTROL BOX SPARE PARTS LIST 16 SP Range 1 SP Range GUARANTEE This equipment is guaranteed by IMC for 2 years from the date of its purchase from IMC or from one of its stockists dealers or distributors The guarantee is l
4. SP RANGE INSTALLATION AND OPERATING MANUAL PLEASE LEAVE WITH OPERATOR SP12 amp SP25 SERIES 4 Imperial Machine Company Limited Unit 1 Abbey road Wrexham Industrial Estate Wrexham LL13 9RF Tel 44 0 1978 661155 Fax 44 0 1978 729990 Service Fax 44 0 1978 667766 Spares Fax 44 0 1978 667759 E mail info imco co uk Website www imco co uk A34 013 R12 ECN 7950 Jan 2013 SP Range EC DECLARATION OF CONFORMITY Guarantee of Production Quality 4771 We Imperial Machine Company Limited of Unit 1 Abbey Road Wrexham Industrial Estate Wrexham LL13 9RF Declare under our sole responsibility that the machine SP12 amp SP25 SERIES 4 As described in the attached technical documentation is in conformity with the Machine Safety Directive 98 37 EC and is manufactured under quality system BS EN ISO 9001 It is also in conformity with the protection requirements of the Electro Magnetic Compatibility Directive 20044 08 EEC and is manufactured in accordance with harmonised standards EN 61000 6 1 Immunity and EN 61000 6 3 Emissions plus product specific standards It also satisfies the essential requirements of the Low Voltage Directive 2006 95 EC and is manufactured in accordance with harmonised standard EN 60204 1 Safety of Machinery Electrical Equipment Approved by S Witt Engineering Manager Signed at Wrexham Jan 2013 SP Range INDEX GUARANTEE 2
5. N3389S di8vo yliz HOLIMS on 430 NO HOLIMS 0193135 318 3ANI 2 7OMINOO gt HINv3 12 SP Range WIRING DIAGRAM 3PH UNITS O3 Ou HINv3 M3ONITAO MOlOA YEZ 6045 2185 09 2 097 YUZ 5045 2145 0 lt lt 00 Sany 39VI1O0A ONILL3S QvOT13AO N_A in LA T3NVd OYINOO I 1 HLS 13 1OMINOO 1 WOINVHOSW LOVINO9 JOLOVINOO 1 e HOLIMS nonna Ny 40193135 lNVIS Y i x 9 2 QVOTH3AO S6 i 4 LOVINO9 QVO TH3AO 96 9 Y 1 NOLOVINOO S e Al 109 ONISION3N3 LL IN 1 I 1 1 1 Os SP Range PARTS ILLUSTRATION NON nf Se s E QOO 24 a o9 CY O aU SP Range SPARES PART LIST SP12 SP25 Item Part No Description Part No Description 1 S58 593 SP12 Low Pedestal 558 590 SP25 Low Pedestal S58 594 SP12 High Pedestal E58 591 SP25 High Pedestal 2 D18 050 Screw M6 x 16 CSK SS D18 050 Screw M6 x 16 CSK SS 3 D20 038 M5 Full Nut SS D20 038 5 Full Nut SS 4
6. 1ph E58 096 Wall Bracket 1ph E58 1 11 Wall Bracket E58 1 11 Wall Bracket 28 558 587 SP12 Control Box 1ph Inverter 558 588 SP25 Control Box 1ph Inverter Inc Wall Bracket amp cables Inc Wall Bracket amp cables 558 596 SP12 Control box 3ph 558 595 SP25 Control box 3ph Inc Wall Bracket amp cables Inc Wall Bracket amp cables G60 370 M2 Mains cable and plug 1ph G60 370 M2 Mains cable and plug 1ph G60 371 Mains cable 3ph G60 371 Mains cable 3ph 29 E58 113 Z SP12 Liner E58 114 Z SP25 Liner 30 S58 545 SP12 Peeler Plate S58 546 SP25 Peeler Plate 31 M58 011 M1 SP12 Rim Moulding 58 011 2 SP25 Rim Moulding 32 S58 592 SP12 Cast Lid assembly S58 589 SP25 Cast Lid assembly Including Spray Nozzle Including Spray Nozzle 33 J04 324 Spray Nozzle J04 324 Spray Nozzle 34 S58 541 SP12 Splash Cover S58 542 SP25 Splash Cover SP12 ACCESSORIES SP25 ACCESSORIES A29 003 Splash Cover Retaining Strap A29 003 Splash Cover Retaining Strap S58 568 Integral Filter Basket S58 568 Integral Filter Basket S58 569 Floor Standing Interceptor Tank 558 569 Floor Standing Interceptor Tank 558 570 Waste ejector 558 570 Waste ejector When ordering spare parts or accessories always quote the SERIES AND SERIAL NUMBER of the machine found on the rating label 15 1PH CONTROL BOX SPARE PARTS LIST SP Range
7. D25 004 5 Shakeproof Washer SS D25 004 5 Shakeproof Washer SS 5 G60 369 Earth Wire Motor to Pedestal G60 369 Earth Wire Motor to Pedestal 6 G40 205 Motorgearbox 0 37kW G40 216 Motorgearbox 0 7 5kW G60 372 Motor cable 1ph G60 372 Motor cable 1ph G60 373 Motor cable 3ph G60 373 Motor cable 3ph G86 003 Ferrite 1ph only G86 003 Ferrite 1ph only 7 D18 050 M8 Full Nut SS D18 050 8 Full Nut SS 8 D25 079 M8 Spring Washer SS D25 079 M8 Spring Washer SS 9 D25 068 M8 Plain Washer SS D25 068 M8 Plain Washer SS 10 S58 549 Bearing Housing Assembly S58 549 Bearing Housing Assembly 11 A02 070 O Ring A02 070 O Ring 12 C28 023 M1 Z2 Waste Outlet Machined C28 023 M1 Waste Outlet Machined 22 13 E58 059 Waste Outlet Cover Plate E58 059 Waste Outlet Cover Plate 14 A11 026 Waste Outlet Gasket 11 026 Waste Outlet Gasket 15 G80 029 Cable Gland G80 029 Cable Gland 16 E58 081 Chute E58 081 Chute 17 D20 031 Screw M6 x 12 Hex SS D20 031 Screw M6 x 12 Hex SS 18 D25 052 M6 Plain Washer SS D25 052 M6 Plain Washer SS 19 D20 031 M6 Dome Head Nut D20 031 M6 Dome Head Nut 20 D25 005 M6 Shakeproof Washer SS D25 005 M6 Shakeproof Washer SS 21 M79 Door Roller M79 Door Roller 22 L21 048 Eccentric L21 048 Eccentric 23 D18 051 Screw M6 x 20 CSK SS D18 051 Screw M6 x 20 CSK SS 24 D21 057 Screw M8 x 20 Pan SS D21 057 Screw M8 x 20 Pan SS 25 S59 253 Door Handle S59 253 Door Handle 26 A00 058 Nylon Shoulder Washer A00 058 Nylon Shoulder Washer 27 E58 096 Wall Bracket
8. waste sludge to enable it to flow easily through the drains without fear of blockage Waste Ejectors are not recommended in the follow circumstances Apipe run exceeding 15m between the machine and main drain When a fall of 1 15 cannot be achieved e When piping is exceptionally complex In any of the above cases an interceptor tank is recommended Fitting the waste ejector If the waste ejector is not fitted to the peeler when it arrives it can be fitted as follows Remove the existing waste outlet Decide on which side the outlet pipe is to be connected and if necessary remove the blanking plate and gasket from the alternative waste outlet position and refit to the other side Fit the waste ejector and gasket in place of the waste outlet The waste ejector has a gt BSP connection for the water supply on each side of the unit Select which is to be used for the water connection and utilise the plug for sealing off the other Connect the hose between the connector at the top of the waste ejector and the water inlet on the peeler lid Waste Ejector adjustments When the pipework is complete set the ejector adjustments to give the correct water flow though the machine Two adjusting screws and lock nuts are provided for this purpose The top one controls flow though the peeler and the lower one controls the jet to the waste pipe Adjust the top screw until the flow through the machine is between 2 25 and 7 litres per minute th
9. FREQUENCY Hz 50 60 8 MODEL 5 12 RATING Ps5 VOLTAGE RANGE 400 460 PHASE gt ames mao ISERIES e kw 59 67 SERIAL NUMBER 5811112001 SP Range 2 INTRODUCTION This machine is intended for peeling potatoes lts use be extended to other root vegetables It is not recommended to use this machine for peeling onions YOUR PEELER SPLASH COVER LID MOUNTING DOOR HANDLE BRACKET WASTE OUTLET 3 SP Range CONTROLS The peeler has a separate box for mounting on a wall bracket near the machine TIMER ON OFF BUTTON TIMER MANUAL SELECTOR SWITCH WALL BRACKET Note Control boxes for three phase machines have separate on and off buttons INSTALLATION For the Installer These Instructions contain important information designed to help the user obtain the maximum benefit from the investment in an IMC SP Peeler Please read them carefully before starting work and consult with the supplier in the event of any queries Be sure to leave this Instruction Manual with the user after the installation of the machine is complete Procedure The SP Range is supplied with a pedestal and is designed to be bolted to the floor The control box is designed to be mounted on a wall bracket so that it is easily accessible once the machine is installed Place the machine in its desired location and mark though the pedestal base the loc
10. arth Brown Live Blue Neutral The wires in the mains lead for three phase supply are coloured Green and Yellow Earth Brown Phase 1 Black Phase 2 Grey Phase 3 The 3 phase machines do not have a neutral wire If the supply has a neutral wire isolate it and only wire the unit to the 3 phases and earth An Equipotential earthing point is located on the back of the cylinder near the cable outlet if equipotential bonding is required Should the mains lead become damaged it must be replaced by an IMC service agent or qualified electrician in order to avoid a hazard 7 SP Range COMMISSIONING After making the electrical connection switch on the machine and check that the direction of rotation of the peeling plate is CLOCKWISE when viewed from above The direction of rotation of single phase units is set at the factory If it is not rotating in the correct direction contact IMC To change the direction of rotation of three phase units switch off the machine isolate the supply and interchange any two phase wires OPERATION 1 2 Fit the peeling plate ensuring that it is properly located on the drive shaft Measure out the potatoes into a container which holds a known measured weight of 12kg or 25kg depending on machine size Check for stones which could damage the abrasive Should this happen the noise will indicate the presence of stones Switch off immediately and remove them The top of the
11. ation of the five floor fixing holes Remove the machine and prepare the floor for rawlbolts or other suitable floor fixings Replace the unit into working position and fit the rawlbolts or other fixings Tighten up the fixings Place the control box bracket in the desired location and mark though the four screw holes Remove the bracket and prepare the wall for rawlplugs or other SP Range 4 suitable wall fixings Replace the bracket and secure in place with four screws Slide the control box onto its wall bracket WATER SUPPLY Connect the water supply pipe to the water inlet located on the top of the lid and secure using the supplied hose clips Fit the other end of the supply pipe to a cold water supply that incorporates a tap or shut off valve that can be used to regulate the water flow to approximately 3 4 litres per minute The water inlet is fitted with a baffle to improve the distribution of water into the cylinder This may cause minor splashing on the surface of the lid if this becomes severe reduce water flow as required The maximum water pressure for the supply is 10 bar Ensure that the hose supplied with the machine is used and that an old hose is not reused PLEASE NOTE these machines are fitted with an air break to prevent back syphonage into the mains supply Some local authorities may nevertheless require connection is made to a storage cistern rather than direct to the mains supply This applies to UK installations on
12. en tighten the lock nut Set the lower screw to allow a jet of water into the waste pipe of 2 25 to 3 5 litre per minute then tighten the lock nut SP Range 6 ELECTRICITY SUPPLY CONNECTION Before connecting examine the rating plate attached to the machine to ensure that the characteristics shown are correct for the supply available Any changes to the supply or new mains runs should be carried out by a qualified electrician and in accordance with the IEE Codes of Practice Single phase machines come supplied with a three pin plug The socket used should be away from any splash area and be accessible with the peeler installed A dedicated supply to the socket is recommended and it should be protected by a C or D class circuit breaker rated at 10A for the SP12 and 16A for the SP25 Three phase machines should be connected to a 15A isolator providing at least 3mm separation in all poles The isolator should be fused at 10A The supply to the machine must also be protected by a 30mA RCD The mains lead fitted to the machine is the minimum required for individual connection to the mains supply Site conditions may vary with additional length of cable run encapsulation in trunking etc being required Should this apply a qualified electrician must alter the lead in accordance with the IEE Codes of Practice WARNING This machine must be earthed The wires in the mains lead for single phase supply are coloured Green and Yellow E
13. imited to the replacement of faulty parts or products and excludes any consequential loss or expense incurred by purchasers Defects which arise from faulty installation inadequate maintenance incorrect use connection to the wrong electricity supply or fair wear and tear are not covered by the guarantee Any damages shortages must be reported to IMC within 24 hours of accepting delivery No claims for damages will be considered if the goods have been onward delivered by you Please observe these instructions carefully The guarantee applies in this form to installations within the United Kingdom only DELIVERY The packaged machine consists of Peeler Unit with lid control box and mounting 1 bracket Peeling plate Water supply pipe and 2 hose clips 1m long 3 flexible waste hose and hose clip Instruction Booklet If any accessories have been ordered they will be supplied in separate packages Please notify both the carrier and the supplier within three days of receipt if anything is missing or damaged Check that the correct machine has been supplied and that the voltage marked on the rating label is suitable for the supply available The rating label is located at the back of the cylinder near the supply cable inlet SAMPLE RATING LABEL e C 3221 IMPERIAL MACHINE COMPANY Ltd F KI LL13 9RF UNITED KINGDOM TEL 44 0 1978 661155 x POTATO PEELER
14. liner can also be used as a maximum loading line Set the run time required on the control panel two minutes is normally more than adequate or select manual operation and press the green start button Turn on the water supply Ensure that the chute discharge door is closed Load the potatoes into the peeler and place the splash cover onto the top of the cylinder The machine is now operating Remove the splash cover to check the progress of peeling process The peeler can be stopped at any time by pressing the Stop button or it will stop on completion of a timed cycle Turn off the water supply open the chute door and while keeping the door open press the Start button to evacuate the potatoes press the Stop button when the peeler is empty Keep the peeled potatoes under water until required for cooking ON NO ACCOUNT put a hand or implement into the machine or wedge the door open while discharging SP Range 8 SAFETY All SP Range peelers are controlled so that if the electricity supply is interrupted the machine will not restart automatically All single phase SP Range controls are fitted with a thermal trip This ensures that the controls cannot overheat and become damaged If the thermal trip cuts in the machine will not run until it has cooled down and the peeler is switched off and on again The controls will not overheat in normal usage Do not put hands into the machine while it is running On single pha
15. ly Overseas customers should install the machine in accordance with local regulations If in doubt check with your local authority WASTE OUTLET CONNECTION The peeler has two possible waste outlet locations If it is required to change the waste outlet location remove both the existing waste outlet and the blanking plate on the opposite side Refit both the waste outlet and the blanking plate in their new positions A flexible hose supplied with the machine can be fitted over the waste outlet to direct the waste into a gully or intercepting tank If required secure with the hose clip supplied Longer lengths of flexible hose are available from IMC on request The waste outlet also incorporates a 2 BSP female thread for connection to standard 54mm 2 waste pipe DO NOT reduce the diameter of the waste pipe to below 54mm The length of the pipe should be kept to a minimum and the pipe must have a fall of at least 1 15 Changes of direction should be made by swept bends rather than elbows and cleaning eyes should be fitted where possible in accordance with standard plumbing practice A trap is not necessary if the discharge is into a gully or an intercepting tank although a trap must be provided in the outlet pipe from the intercepting tank If a trap is required it should be made with 45 bends and not with a U or P bend or with a bottle trap 5 SP Range WASTE EJECTOR The waste ejector is an optional fitting that dilutes the
16. nit is serviced an IMC approved engineer at least once a year The motor in the single phase units is controlled via an inverter The following warnings must be observer before working on this unit WARNING Only suitably qualified personal should service this equipment after becoming familiar with all safety notices installation operation and maintenance procedures related to the inverter WARNING Risk of electric shock The capacitors in the inverter remain charged for 5 minutes after power has been removed Do not open the control box until 5 minutes after power has been removed WARNING Repairs to the inverter may only be carried out by Schneider Service or by repair centres authorised by Schneider gt D Details of IMC Service Contracts are available on application ORDERING SPARE PARTS In the event that spare parts or accessories need to be ordered please always quote the SERIES AND SERIAL NUMBER of the machine This is to be found on the rating plate located near the supply cable For installations outside the UK please contact your supplier For information on IMC spares and service support if applicable please call IMC on 44 0 1978 661155 Alternatively contact us via email or fax IMC Service Desk Fax 44 0 1978 667766 E mail service imco co uk IMC Spares Desk Fax 44 0 1978 667759 E mail spares imco co uk SP Range WIRING DIAGRAM 1PH UNITS MOLON HI3v3
17. se machines do not unplug the unit with wet hands CLEANING It is essential to clean the machine at least once a day preferably at the end of each period of operation Switch off at the socket or isolator Remove the lid and splash cover Lift out the peeling plate Clean the peeling plate and cylinder in a sink potwash or by hosing with a spray Rinse the inside of the peeling chamber and base with warm water using a mild detergent if necessary to remove starch build up 6 Wipe the exterior of the machine with a damp cloth again using a mild detergent if required ROD DO NOT USE CLEANING MATERIALS CONTAINING ABRASIVES OR BLEACHES DO NOT STEAM CLEAN DO NOT CLEAN WITH WATER JET 9 SP Range DO S AND DON TS Do Install on a level service Do Ensure power supply isolator or socket is accessible with the peeler installed Do Clean the machine after each period of use Don t Sit or stand on top of the peeler Don t Place hands inside unit while discharging or peeling Don t Use the unit outside MATERIAL CONTENT The SP Range peelers contain the following materials Metals Stainless steel Mild steel inc plated Aluminium and copper Plastics and rubber Polycarbonate Nylon Neoprene rubber Other Aluminium oxide electrical components SP Range 10 MAINTENANCE Other than regular cleaning the SP Range of peelers require no maintenance by the end user It is recommended that the u
Download Pdf Manuals
Related Search