USER`S MANUAL Wired Remote Control
Contents
1. What the funcion inchaators mean Filter sign indicator On The filter inserted in the air conditioner needs to be cleaned Clean up the filter Temp and reset the indicator by pressing the y G En buttons at once for 5 seconds Off The filter inserted in the air conditioner is working well No action needed Mode lock indicator 4 On The mode lock function is activating You can not change the operation mode Press and hold the and kJ buttons for 5 seconds to activate and deactivate the function Off The mode lock function is deactivating You can change the operation mode by short pressing the Mode button You cannot activate the function with slave wired remote controls Slave wired remote controls just display the activating status only Centralized control indicator On The upper controllers For example centralized controllers and S NET series activate central control You cannot control the devices with the wired remote control when central control is activating Off Central control is deactivating You can control the connected devices with the wired remote control Getting Started You have just purchased a wired remote control and it has been installed by your installation specialist Your User s Manual contains much valuable information on using your wired remote control Please take time to read it as it will help you take full advantages of the unit s features2. eg USER S MANUAL Wired Remote Control MWR SH00 System Air Conditioner AS E DB98 28134A 1 Safety Precautions e Before using the wired remote control read carefully these instructions e After reading the instructions keep this user s manual in a handy and safe place If auser is changed you must hand over the manuals e Never attempt to install the air conditioning system or to move the wired remote control by yourself WARNING N CAUTION Do not attempt to install or repair this wired remote control by yourself This remote control contains no user serviceable parts Always consult authorized service personnel for repairs When moving consult authorized service personnel for disconnection and installation of the remote control Ensure that the wall is strong enough to support the weight of the remote control Must install the remote control with rated power supply In the event of a malfunction burning smell etc immediately stop operation turn off the electrical breaker and consult authorized service personnel Do not use inflammable gases near the remote control Do not spill water into the wired remote control Do not operate the remote control with wet hands Do not install the remote control in a location where it will come into contact with the combustible gases machine oil sulphide gas etc 4 Do not press buttons with a pointed thing Do not pull
3. be turned on with the mode selected when the unit was last used Result The air conditioner has a built in protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped The air conditioner will start up after 3 minutes 2 To select the Cool mode press the displayed on the remote control Result 3 To adjust the temperature press the y button until 2 is Cool The air conditioner will run in Cool mode the desired temperature The temperature can be set between 18 C and 30 C Result Temp A buttons to set The temperature is adjusted by 1 C when Temp the y A buttons are pressed The air conditioner will start cooling if the temperature set is lower than the room temperature The fan will run even if the temperature set is higher than the room temperature 4 To adjust the fan speed refer to page 11 The Cool and Heat mode cannot be selected at the same time c U amp Kad Clic 5 Ka S N Temp Fan V A Speed Selecting the Heat Mode The Heat mode can be selected only on the heat pump models Select the Heat mode to raise the room temperature 1 Press the OI ON OFF button to turn on the indoor unit Do not press the O ON OFF button if the remote control is on Result The air conditi
4. In the manual you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use 3 different symbols Selecting the Auto Mode The room temperature and the fan speed are controlled automatically in the Auto mode 1 Press the ON OFF button to turn on the indoor unit Do not press the ON OFF button if the remote control is on Result The air conditioner will be turned on with the mode selected when the unit was last used The air conditioner has a built in protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped The air conditioner will start up after 3 minutes 2 To select the Auto mode press the button until fa is ILI displaved on the remote control Result The air conditioner will run in Auto mode Temp 3 To adjust the temperature press the v A buttons to set the desired temperature IM Ta The temperature can be set between 18 C and 30 C E Lic auto He al Result The temperature is adjusted by 1 C when the Fil buttons are pressed ol AN Selecting the Cool Mode Select the Cool mode to lower the room temperature 1 Press the ON OFF button to turn on the indoor unit Do not press the ON OFF button if the remote control is on The air conditioner will
5. hen it is started immediately after being Plugged in Stopped The air conditioner will start up after 3 minutes 2 To adjust the fan speed press the u button The fan speed is adjusted as follow when the gee button is IU Fan pressed L te 5 Low Fuad Ku Medium mnd MN Temp KR ad High Fan V A Speed Se s Automatic rotated Sua gt Bad kI a ELECTRONICS
6. oner will be turned on with the mode selected when the unit was last used The air conditioner has a built in protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped The air conditioner will start up after 3 minutes To select the Heat mode press the button until E is JU displaved on the remote control c ae Result The air conditioner will run in Heat mode Se A m Temp To adjust the temperature press the v 4 buttons to set the desired temperature The temperature can be set between 16 C and 30 C Result The temperature is adjusted by 1 C when the Fia buttons are pressed i ie Cm The air conditioner will start heating if mic Heat the temperature set is higher than the room So al temperature The fan will run even if the temperature set is lower than the room temperature Temp y Ja 4 To adjust the fan speed refer to page 11 Nota The Cool and Heat mode cannot be selected at the same time Selecting the Dry Mode Select the Dry mode if the room is too humid Using this mode will slightly lower the room temperature 1 Press the ON OFF button to turn on the indoor unit Do not press the ON OFF button if the remote control is on Result The air conditioner will be turned on with the mode selected when the unit was last u
7. or bend the wired remote control cable excessively Do not use this wired remote control for other purpose Do not spray an insecticide or other combustible things on the wired remote control Do not clean the wired remote control with benzene solvents or other chemicals Do not give a shock to the wired remote control or disassemble it by yourself Contents WIRED REMOTE CONTROL esessszzzzsnannmmnnzznnszssssonennnnenzazasssssssz GETTING STARTED ssssnenzzzzznvnnnzzznnnnnnnazzznnnnenazznnnnnenazasnnnnnzzzsz 0 SELECTING THE AUTO MODE sssssvenzzzzsnnnnnzzzznnnnanazzsnnnnnzzzsz 0 SELECTING THE COOL MODE sessennezzzzzsnnnanzazzsennnnazzsnnnnzzzsz 0 SELECTING THE HEAT MODE ssssnennzzzasnnnanzzzanennanazzannnnnzazsz SELECTING THE DRY MODE eeessssnnnzzzzzsnnnanzzzzzonenzazzannnnnzazsz SELECTING THE FAN Mope DISPLAVING THE Deice MODE ADJUSTING THE FAN SPEED ssssssssensnnanzanssssssanzannnnnnzasassssssaa Wired Remote Control The wired remote control is installed on the wall Temperature indicator Operation mode indicator Delce Dry Fan a IX Auto Cool Heat Cool Heat lock sali Fan speed indicator Centralized Centralized Ctrl ar ne Function indicator Mode 3 Mode selection button On Off button Fan speed button EN A CDI tt adjustment buttons
8. sed The air conditioner has a built in protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped The air conditioner will start up after 3 minutes 2 To select the Dry mode press the button until E is displayed on the remote control ILI 2 Gi Result The air conditioner will run in Dry mode Temp 3 To adjust the temperature press the 7 A buttons to set the desired temperature The temperature can be set between 18 C and 30 C Mode Result The temperature is adjusted by 1 C when Temp the y A buttons are pressed The fan speed is adjusted automatically in the an ka Dry mode Cu 3 Dual nd A Selecting the Fan Mode Select the Fan mode to circulate air without changing the temperature 1 Press the ON OFF button to turn on the indoor unit Do not press the ON OFF button if the remote control is on Result The air conditioner will be turned on with the mode selected when the unit was last used The air conditioner has a built in protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped The air conditioner will start up after 3 minutes o select the Fan mode press the vese button until is 2 To select the Fan mode press
9. the Wed button until amp SE jk displaved on the remote control am c TE Result The air conditioner will run in Fan mode Dad mode 3 To adjust the fan speed refer to page 11 When the air conditioner is operating in the fan mode you can not select the automatic fan speed Displaying the Deice Mode When the Deice mode indicator is on it means that the air conditioner is defrosting its outdoor unit under the Heat mode When the air conditioner is under heating operation in cold weather there may be frost generated by difference of the temperatures Under this circumstance the air conditioner defrosts by itself to increase the efficiency and save energy You can not activate the Deice mode because it is activated automatically and just displayed on the wired remote control Though you change the operation mode before the defrosting is completed the Deice mode indicator is on until the air conditioner finishes the operation The Deice mode indicator is off after the air conditioner completes defrosting Adjusting the Fan Speed Change the fan speed fit in your circumstances 1 Press the ON OFF button to turn on the indoor unit Do not press the O ON OFF button if the remote control is on Result The air conditioner will be turned on with the mode selected when the unit was last used The air conditioner has a built in protection mechanism to prevent the unit from being damaged w
Download Pdf Manuals
Related Search