LNP-0800-24 series
Contents
1. Data 1 2 3 6 PoE Pin Assignment Per unit Power 1 Green Power 2 Green Fault Red Per port Link Activity Green PoE Feeding Power Green 10Base T 2 pair UTP STP Cat 3 4 5 5e cable EIA TIA 568 100 ohm 100m Network Cable A 100Base TX 2 pair UTP STP Cat 5 5e 6 cable EIA TIA 568 100 ohm 100m Over Current Single Blown Fuse Protection Redundant Power DC 12 36V with Connective Power Input 1 6 Pin Removable Terminal Block Max Power 145 Watts 12V 200 Watts 24V Consumption Full Load with PoE Function Installation DIN Rail Mounting Wall Mounting Standard Operating Temperature 10 C to 70 C Operating Temp r Wide Temperature model 40 C to 75 C Operating ER 5 to 95 Non Condensing Humidity Storage 40 C to 85 C Temperature IP 30 46mm W x 99mm D x 142mm H FCC Class A CE EN61000 4 2 3 4 5 6 8 CE EN61000 6 2 CE EN61000 6 4 eater UL 508 Please check Antaira s website for the most up afe y to date certification status IEC60068 2 32 Free fall Stability testing IEC60068 2 27 Shock IEC60068 2 6 Vibration2. NCaIra LNP 0800 24 series 8 port Industrial POE Unmanaged Ethernet Switches 8 10 100Tx 30W Port 12 36VDC Input User Manual Ntaira www antaira com FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio TV technician for help CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Content Inrod
3. Power on the Industrial switch Please refer to the Wiring the Power Inputs section for information about how to wire power The power LED on the Industrial switch will turn on Please refer to the LED Indicators section for indication of LED lights 5 Prepare the twisted pair straight through Category 5 above cable for Ethernet connection 6 Insert one side of the RJ 45 cable into the Industrial switch Ethernet port and on the other side to the network device s Ethernet port e g Switch PC or Server The Ethernet port RJ 45 LED on the Industrial switch will turn on when the cable is connected to the network device Please refer to the LED Indicators section for LED light indication 7 When all connections are set and the LED lights all show normal the installation is complete Network Application This segment provides an example of an industrial switch application Fiber Cable VOIP Phone IP Camera Wireless AP IEEE 802 3af at Compliant Powered Devices Troubleshooting m Verify the right power cord adapter never use power supply adapter with non compliant DC output voltage or it will burn the equipment m Select the proper UTP STP cable to construct the network with using the right cable Use unshielded twisted pair UTP or shield twisted pair STP cable for RJ 45 connections 1000 Category 5e above cable for 10M 100Mbps Also be sure that the length of any twisted pair connection does not exceed 100 meters 3
4. connector as the picture shows below By Inserting the wires it will detect the fault status including power failure or port link failure managed industrial switch only and form a normally open circuit An application example for the fault alarm contact is shown as below PWRI on PWR2 24V de 1A Resistance Note e Use Copper Conductors Only 60 75 C Tighten to 5 Ib in e The wire gauge for the terminal block should range between 12 24 AWG DIP Switch Settings The following describes the DIP switch settings ON Enables the corresponding PORT alarm If the port s link fails the m m relay will form an open circuit and the fault LED will turn on s HBEBEBBEE oO 3 Off Disables the corresponding PORT alarm The relay LE will form a closed circuit and the fault LED will never o oO a turn on 2YLILLTILS Qacaaaanag B S P On Enables broadcast storm protection B S P Off Disables broadcast storm protection Mounting Installation DIN Rail Mounting The DIN Rail is screwed on the industrial switch from the factory If the DIN Rail is not screwed on the industrial switch please see the following pictures to screw the DIN Rail on the switch Follow the steps below to hang the industrial switch 1 Use the screws to screw the DIN Rail bracket on the rear side of the industrial switch To remove the DIN Rail bracket reverse the step 1 After the DIN Rail bracket is screwed on the rear side of the switch inse
5. 28 feet m Diagnosing LED Indicators To assist in identifying problems the Switch can be easily monitored through LED indicators which describe common problems a user may encounter and where the user can find possible solutions m Ifthe power indicator LED does not turn on when the power cord is plugged in the user may have a problem with the power cord Check for loose power connections power losses or surges at the power outlet Please contact Antaira or Antaira s authorized channel partners for technical support service if the problem still cannot be resolved m f the Industrial switch LED indicators are normal and the connected cables are correct but the packets still cannot transmit Please check the system s Ethernet devices configuration or status Technical Specification The LNP 0800 24 series 8 Port Industrial PoE Unmanaged Ethernet Switch technical specifications is shown below IEEE 802 3 10Base T Ethernet IEEE 802 3u 100Base TX Fast Ethernet Standard IEEE802 3x Flow Control and Back Pressure IEEE802 3at Power over Ethernet 14 880 pps for 10Base T Ethernet port Transfer Rate 148 800 pps for 100Base TX Fast Ethernet port MAC Address 2K MAC Table size 8 10 100BaseT X auto negotiation speed Full Half RJ45 Port duplex mode and auto MDI MDI X connection RJ 45 port 1 8 support IEEE 802 3at End point Alternative A mode Positive VCC RJ 45 pin 1 2 Negative VCC RJ 45 pin 3 6
6. atts of power per port The switches can be used to power IEEE 802 3af or 802 3at compliant power devices PD eliminating the need for additional wiring and support IEEE 802 3 802 3u 802 3x with 10 100BTx full or half duplex MDI MDI X auto sensing to provide an economical solution for the Industrial Ethernet Network In addition the Network Broadcast Storm Protection and built in relay warning function alerts network engineers when power failures or port breaks occur Features m System Interface Performance RJ 45 ports support Auto MDI MDI X Function Embedded 8 port 10 100Tx w PoE Store and Forward Switching Architecture Broadcast Storm Protection 2K MAC Address Table Port Break Alarm Mask m Power Supply gt DC 12 36V Redundant Power m Operating Temperature gt Standard Operating Temperature model 10 C 70 C gt Extend Operating Temperature model with T 40 C 75 C VV v v V WV m Case Installation gt IP 30 Protection gt Installation in Pollution Degree 2 Environment gt DIN Rail and Wall Mount Design m Provides EFT protection 2 000 VDC for power line Supports 6 000 VDC Ethernet ESD protection Package Contents Please refer to the package contents list below m LNP 0800 24 series 8 Port Industrial PoE Unmanaged Ethernet Switch w DIN Rail Bracket User Manual Removable Terminal Block Wall mount Kit 2 Wall mount Plates with Screws Compare the contents of the industrial switch with the checklist ab
7. e port alarm is disabled PoE Indicator On The port is supplying power to the powered device reen Port 1 8 Off No powered device attached or power supplying fails Green On Connected to network 100Mbps Flashing Networking is active LAN Port 1 8 Off Not connected to network RJ 45 Green On Connected to network 10Mbps Flashing Networking is active Off Not connected to network T Ports m RJ 45 ports The RJ 45 Fast Ethernet ports will auto sense for 10Base T or 100Base TX connections Auto MDI MDIX means that the switch can connect to another switch or workstation without changing straight through or crossover cabling Please refer to the table below for RJ 45 pin assignment m RJ 45 Pin Assignments Pin Number Assignment 1 Rx 2 Rx 3 TX 6 Tx Note and signs represent the polarity of the wires that make up each wire pair All ports on this industrial switch supports automatic MDI MDI X operation users can use straight through cables See figure below for all network connections to PCs or servers or to other switches or hubs With straight through cable pins 1 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable The table below shows the 10BASE T 100BASE TX MDI and MDI X port pin outs Pin MDI X Signal Name MDI Signal Name 1 Receive Data
8. ove If any item is damaged or missing please contact Antaira or Antaira s authorized channel partners for service Hardware Description The Industrial switch s hardware spec port cabling information and wiring installation will be described Physical Dimension The LNP 0800 24 series 8 Port Industrial PoE Unmanaged Ethernet Switch dimension W x D x H is 46mm x 99mm x 142mm V ie W DW View vie View Front Side Back Back Front Panel The Front Panel of the PoE Industrial Switch is shown below Front Panel of the PoE Industrial Switch Top View The top view of the PoE Industrial Switch has one terminal block connector of two DC power inputs and relay circuit contact One DIP switch for port break alarm mask and broadcast storm protection O O O O O O O 000089 34942272 aaaa ad aa Top View of the PoE Industrial Switch LED Indicators The diagnostic LEDs located on the front panel of the industrial switch provide real time information of the system and optional status The following table provides the description of the LED status LED Color Description On Power input 1 is active P1 Green Off Power input 1 is inactive On Power input 2 is active P2 Green Off Power input 2 is inactive On Power input 1 or 2 has failed port link is inactive Fault Red ae Power input 1 and 2 are both functional or no power inputs port s link is activ
9. plus RD Transmit Data plus TD 2 Receive Data minus RD Transmit Data minus TD 3 Transmit Data plus TD Receive Data plus RD 6 Transmit Data minus TD Receive Data minus RD The following figures show the cable schematic for both straight through type and crossover type Switch Router or PC 3 TD gt 3 RD 6 TD gt 6 RD 1 RD I TD 2 RD 2 TD Straight Through Cable Schematic Switch Switch 3 TD 3 TD 6 TD 6 TD 1 RD 1 RD 2 RD 2 RD Cross Over Cable Schematic Cabling m Twisted pair segments can be connected with an unshielded twisted pair UTP or shielded twisted pair STP cable The cable must comply with the IEEE 802 3u 100Base TX standard e g Category 5 5e or 6 The cable between the equipment and the link partner switch hub workstation etc must be less than 100 meters 328 ft long Wiring the Power Inputs Please follow the steps below to insert the power wire Insert the positive and negative wires into the PWR1 V1 V1 and PWR2 V2 V2 contacts on the terminal block connector V1 Vi V2 V2 Tighten the wire clamp screws to prevent the wires from loosening Note e Use Copper Conductors Only 60 75 C Tighten to 5 Ib in e The wire gauge for the terminal block should range between 12 18 AWG Wiring the Fault Alarm Contact The fault alarm contact is in the middle of the terminal block
10. rt the top of 10 DIN Rail on to the track 4 Then lightly pull down the bracket on to the rail 5 Check if the bracket is mounted tight on the rail 6 To remove the industrial switch from the rail reverse steps above Wall Mounting Follow the steps below to mount the industrial switch using the wall mount bracket 1 Remove the DIN Rail bracket from the industrial switch loosen the screws to remove the DIN Rail 2 Place the wall mount bracket on the top and bottom of the industrial switch 3 Use the screws to screw the wall mount bracket on the industrial switch 4 Use the hook holes at the corners of the wall mount bracket to hang the industrial switch on the wall 5 Toremove the wall mount bracket reverse steps above Below is the dimension of the wall mount bracket Hardware Installation This section is to explain how to install the LNP 0500 24 series 5 Port Industrial PoE Unmanaged Ethernet Switch Installation Steps 1 Unpack the Industrial switch packing 2 Check if the DIN Rail bracket is screwed on the Industrial switch If the DIN Rail is not screwed on the Industrial switch please refer to the DIN Rail Mounting section for DIN Rail installation If users want to wall mount the Industrial switch then please refer to the Wall Mounting section for wall mount installation 3 To hang the Industrial switch on a DIN Rail or wall please refer to the Mounting Installation section 4
11. ueNoh vas 1 FEAR 1 Package Gomenisuuuarapumnennnndue 2 Hardware Description rnnrnnnnnnnnvnnvnnnnnnnnnnevennnnnnnuner 3 Physical Dimension snssrnnnnrennennnnennennnnnnnnnnnnenee 3 PRONE Panel ssaseidsseceocssnscnesden aesdusstsncasdasechsccensiassesrects 4 TOD VEN oe N SNE 4 LE DUINGICALONS EEE 5 PONS aan a a ea Ste a eae ee 6 GADING LNL 7 Wiring the Power Inputs ceeeeeeeeeeeeeeneeeeeees 8 Wiring the Fault Alarm Contact rrrrnnnnvnvnnnnnrrnnnnnn 9 DIP Switch Settings cccccccessssseeeeeeeeeeseseeeeeeeees 9 Mounting Installation rxrrrrnnnnnnnnnrrrnnnnnnnnevernnnnnnnr 10 DIN Rail Mounting rrvrnnrrnnnrrnvrnnrrnnnrnnvrnnrrnnsnrneen 10 Wall Mounting eeaeee ae a a a aii 12 Hardware Installation sssrnnrrrnnnnnnnnvrnrnnnnnnnnevennnnnnnnr 13 Installation Stepsusanaussamm rnadsatsannsed 13 Network Application ssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnr 14 Troubleshooting sas nuuvrvvnnnnnnnnnnnnnnnnnnunevennnnnnnunenennn 15 Technical Specification sn xxxnnnnnvnnrnnnnnnnnnnnnnnnnnn 16 Introduction Antaira s LNP 0800 24 series switches are smart 8 port Industrial Unmanaged Ethernet Switches supporting IEEE 802 3at compliant Power over Ethernet Plus on ports 1 to 8 The switches are classified as power source equipment PSE and when used in this way the LNP 0800 24 series switches enable centralization of the power supply and provide up to 30 w
Download Pdf Manuals
Related Search