USER`S MANUAL
Contents
1. on the finder panel will be lit as soon as the cable is well connected While installing the antenna make sure that the LNB in port of finder is well connected to the tuner of the antenna with tested cable Turn the antenna in the approximate direction the finder will light the LED bar and beep when the antenna is close to the satellite Continue to turn the antenna in the direction that makes the finder lights more LED and beep quicker View the PWR value on the screen continue to turn the antenna until the finder shows the maximum value of PWR lock in the best position of antenna e Through this function user can quickly and easily find the right satellite and accurately set the dish NOTES gt Warning e Only qualified personnel may dismantle device and charger Do not drop device and charger into water or fire Do not shock or vibrate the device and charger e Make sure that the battery is full charged while upgrading Do not switch off the device or pull out the cable while upgrading The device will restart automatically after upgrading gt Battery amp charger e Only use original batteries and chargers The use of any other types may be dangerous or damage to device e Dispose of batteries according to local regulations e Do not crush puncture the battery Avoid extreme temperatures and high pressure e If left unused a full charged battery will lose it s charge over time please recharge before u2. USER S MANUAL Digital satellite Meter SH 500 FRONT PANEL on 0 OBAG0ON USB Port AV In AV Out POWER button LCD Display L22K 13V 18V LED LOCK LED POWER LED LNB IN Test Port Function button Menu button Exit button Navigation cross OK button IR USB port for PC connection and power supply connection Input audio and video signal Output audio and video signal Switch meter on off Display the TV program the operation menu and the detailed parameters LED lights when 22K 13V 18V switch on LED lights when satellite signal is locked Operation Red the finder is on Off the finder is off Charg rging Green The battery is being charged Orange The battery is full Satellite signal input Tested cable input F1 Switch LCD on off F2 Mute F3 Switch the display F4 Turn on GPS SH 500G Display the main menu Leave the current menu cancel operation Navigation through n menus switching programs A Y volume control gt OK button confirmation of a selection Receive the infrared signals INSTRUCTION gt Charging e If the finder is being used for the first time it may be necessary to charge for about 12 hours If the battery runs low during use you should recharge it for 5 to 6 hours it will be full when the power light turns to orange from green Fully rechargeable Li on battery can last approximately 3 5 hours e It may be ne
3. cessary to turn off the finder while charging Universal charger operating on 110vac 60Hz or 220vac 50Hz makes it usable anywhere gt Turn on off Press and hold the POWER button for 2 seconds the meter will turn on e Press and hold the POWER button for 2 seconds again to turn off gt Enter registration code e It s necessary to enter the registration code when you first start up or restart after updating the softwares and parameters You can find the code item in the manual and enter it into the meter by pressing the direction buttons lt gt move the cursor to the alteration location A V choose numbers or letters After that press OK button to confirm e Registration code is the security and after sale guarantee please keep it safely gt Language setting e From the system setting menu you can find the language setting item select you favourable language and press OK button gt Angle Calculate INSTRUCTION Press the A V button to select the following points Sat Name GPS Local Longitude Local Latitude Recalculation Sat Name GPS Local Longitude Local Latitude Recalculation Az El Pol gt Satellite Finding Select the desired satellite Select the GPS On or Off The meter will load the longitude and latitude of your position automatically if GPS on or you input them by yourself Input your local longitude Input your local latitude After the completion of all value
4. s press OK button to angle calculation show the azimuth angle of the chosen satellite show the elevation angle of the chosen satellite show the polarity angle of the chosen satellite Select Satellite From the finding menu move cursor to Sat Name you can browse the satellites list use lt b buttons to switch between different satellites select the one you want press OK button INSTRUCTION Select LNB e From the finding main menu move cursor to LNB Type Use buttons to choose LNB Type between single and double local oscillator then move cursor to next bar Use 4 buttons to select the default LNB frequency The LNB frequency must be the same as on the antenna If no default frequency you need press OK button to edit you can key in the LNB frenquency by using direction buttons and press OK button in the end Select parameter e From the finding main menu move cursor to TP Use 4 buttons to select the parameter that you want e If no default parameters you need press OK button to edit you can key in the frequency symbol rate and polarization by using direction buttons and press OK button in the end Detect satellite signal After signal detected the finder show the signal bar and beeps View the PWR C N FEC a BER and NIT on the screen the value of POWER is higher the strength of signal is better and stronger You can also search the satellite channel list by pressing OK b
5. sing e Unplug the charger from the electrical plug when not in use Service Product Certificate Product Serial Number Registration Code After purchased please read out the product serial number and register code form the back of battery cover fill in the relevant form on the top and register code on the official site to verify Official Sit Technical Specifications LNB input F type connector Frequency range Input level Input Impedance LNB power supply LNB switch control Demodulator Demodulator front end Symbol rate Measurement Unit Connectors Serial data interface Video audio interface Power supply Supply voltage Li on battery Working time Supply voltage charger Temperature Operating temperature torage temperature IEC 169 24 950 MHz 2150 MHz 65dBm 25dBm 750 14 18V max 650mA 22 kHz QPSK 2Mbps 45 Mbps dBm dBuV MINI USB 3 5mm DC14 5V 1 5A 2550mA about 3 hours AC 110 250V 50 60 Hz 0 C to 40 C 10 C to 50 C
6. utton Value 0 0 E shows the longitude of the chosen satellite DiSEqC shows the DiSEqC port of the chosen satellite Az shows the azimuth of the chosen satellite El shows the angle of elevation of the chosen satellite Pol shows the polarity angle of the chosen satellite LAT shows the local latitude of the chosen satellite LONG shows local longitude of the chosen satellite NIT shows the longitude of the locked satellite CIN shows the C N value ofthe locked satellite FEC shows the FEC value of the locked satellite a BER shows the a BER value of the locked satellite INSTRUCTION gt Restore factory setting e From the system setting menu you can find the reset setting item Press OK button and input the password You can choose factory type You can choose delete CA channels delete radios channels delete all channels and restore to factory Press OK button to confirm e After factory resetting all modified and saved contents will be lost gt Upgrade Download the latest software parameters and update tool from our Website e The satellite parameters need to be updated every three months gt Notice Before being ready to seek satellite signal make sure that the cable is properly connected through the testing port of finder first Take the LNB in port of finder or In port of digital satellite receiver as the output of tested cable Turn on the finder and receiver if used the test light
Download Pdf Manuals
Related Search