DVB-T DIGITAL TV`RECEIVER
Contents
1. 16 speed rewind gt gt by remote control key you can press 2 4 8 16 speed fast forward manner Such as fast forward to the current time time shift automatic withdrawal state 11 Trouble Shooting Before contacting your local service please make sure following instructions If the product does not work normally after completing the following trouble shooting please contact your local product distributor or service center 1 No message is displayed on the front panel or product has no power Check the main power cable and check that it is plugged into a suitable power outlet Check whether Power Switch is On 2 No picture Make sure that the product is in Operation Mode Make sure that the AV Cable is firmly connected to the TV Make sure that aerial line is correctly connected to the equipment Check the brightness level of TV Check the channel is on air 3 Poor picture amp sound quality Install aerial where there is not obstacle ahead Make sure to avoid putting mobile phone or microwave oven near around the equipment 4 No or poor sound Check the volume level of the TV and the remote control Check the Mute status of the TV and product Press the Audio button to change the Sound Track type 5 Remote control does not operate To manipulate the equipment with remote control the remote control s emitting part should directly point towards the receiving part of receiver s remote co2. to your desired channel and the corresponding channel frequency signal strength and signal quality will be change automatically gt Frequency You can also enter the frequency that you want to search by pressing numeric keys 0 9 on the remote control when the focus is on frequency If you think all the above parameters are ready press OK key to begin the manual search procedure When finished the result will be displayed 8 3 Default Setting Default Setting restores the receiver to the factory default settings After Default Setting is carried out and exit the main menu the Installation Wizard will be automatically run Warning Please note that once you perform Default Setting all data such as Channel information and user configured data are deleted 9 Program record you can directly press the key of Yellow on the Remote Controller set the recording time Press OK to start recording after the Enter the menu USB PLAYBACK USB devices can list a list of recorded programs Can select the appropriate file for playback 10 Time shift ui 3 you can directly press the key of PLAY PAUSE on the Remote Controller the screen suspended Such as inserting USB device start recording PLAV PUASEJ on the remote control again key the moratorium began to broadcast from the bottom of the screen time to be playing there afi gt gt by remote control key the way can be 2 4 8
3. AV key to display FAV lists directly 2 Select your desired channel using the A W keys and press the OK key to change the channel 4 5 Text service If your chosen channel has teletext feature you can access it Teletext service often is loaded automatically shortly after the Digital Teletext window is displayed 1 Press TEXT key to access teletext features 2 Press EXIT key again to return to normal viewing 5 EPG The Electronic Program Guide EPG displays program information about each channel based on the date and time You can also schedule your watching using the information given There are three elements on the screen gt Video window Display current channel program gt Channel list Press A W keys to switch to prior next channel Press TV RADIO key to switch between TV List and Radio List gt Program list A list of program information of current channel 5 1 Browse Program Information gt Ifthe focus are not on the channel list press EPG key gt Press keys to select a day from Monday to Sunday It will be displayed at the top of the program list gt Press EPG key to set the focus on program list and then press A V keys browse the program information 6 Svstem 6 1 Parent Control If password is enabled Parent Control can prevent children from watching some channels which are locked Of course it will restrict them to access some system s
4. Press to turn on off the recording KEY 2 Installation 2 1 Connections Install of DIV Antenna Audio Qutput Left Audio Output Right Wess Video Output b DCI 24V Volts Batterv Antenna 2 2 Replacing the Remote Control Batterv 1 Always use new battery when replace the old set 2 Do not attempt to charge short circuit disassemble heat or burn used batteries battery may be explode if mistreated 3 Battery replacement is necessary when remote control acts sporadically or stops operating 4 Do not drop apply shock or step on the remote control 5 Do not spill water on the remote control 6 Do not place objects between the remote control and remote sensor 7 Do not use remote control for the other equipments at the same time the dashboard 9 Keep the lithium battery out of the reach of children Should the battery be swallowed immediately consult a doctor may be a risk of fire or explosion 11 Do not hold the battery with metallic tweezers otherwise a short circuit may occur 12 Wipe the battery with dry cloth to assure a good contact 13 Under normal conditions batteries will last approximately year The service life may be o shorter depending on the conditions of use de 8 Do not leave the remote near any heat sources or in a place subject to direct sunlight especially on 10 If the REMOTE
5. User s manual DVB T DIGITAL TV RECEIVER ONTENTS 1 lintroduction 1 1 1Precautions 1 1 2Main function wanna 1 3 1Lavout of the main unit 2 1 3 2Lavout of the remote control 3 2 Installation 1 A 2 1 Connections ___ __ __ _ 6 2 2 Replacing the Remote Control Battery _ 2 3 Accessories Included 5 3 Installation Wizard 5 4 Basic Operation 5 4 1Switch Channel 5 4 2Volume Control 5 4 3Program Information 4 4Channel List 8 6 4 5Text service 7 5 EPG 5 1Browse Program Information 7 6 System _____ ________ _ _______ _______ ________ _____ _8 6 1Parent control ___ ____ _________ ___________ __ 6 2Svstem Information 8 7 Channel management 7 1 Edit TV channels 8 7 2 Edit radio channels 9 7 3 Add TV Favorites 9 8 Installation e e eee e 9 8 1Automatic Search 9 8 2Manual Search 10 8 3Default setting _ 10 9 Program record e 10 10 Time shift 11 11 Trouble shooting 12 12 Tech
6. does not operate even when you operate the remote control from a close range it is time to replace the battery refer ring to the label on the back of the basic control Use any of other 2 3 Accessories Included Remole control DIV Arlenra g J Power S ppiy Audic Video Cable 3 Installation Wizard When powering on you receiver for the first time the installation wizard is automatically started You can enable the Installation Wizard in Default Setting It recommends you to finish the Installation Wizard If you exit the Installation Wizard without fully completing the setting procedures you maybe can t watch all TV or radio programs In this case you can use the Installation Menu to configure your receiver as you like 4 Basic Operation This chapter describes the basic functions such as switching channel volume control when watching TV 4 1 Switch Channel The channel can be changed through one of the following methods 1 Press the A W keys to move to the numerical prior or next channel 2 Input the desired channel number using the numerical keys 0 9 to move to the channel directly 3 Press the TV Radio key to switch between TV channel and Radio channel 4 You can also switch channel using Electronic Program Guide or Channel List 4 2 Volume Control 1 Press the lt gt keys to decrease increase the audio volume 5 2 Press the MUTE key to pause the sound of your program te
7. etting menus only if they know the right password gt Password Enable Use P keys to select between Enable and Disable gt Old Password If you want to change the password you have to enter the old password first Press A V keys to set the focus on Old Password then input four number using numeric keys 0 9 on the remote control If this is finished the focus will switch to New Password automatically gt New Password Enter a four number new password gt Verify Password Input the new password again for confirmation 6 2 System Information From here you can get information about the receiver such as hardware version software version release date loader version and driver version 7 Channel Management 7 1 Edit TV Channels From here you can lock channels delete channels and move channels gt Lock Select the channel that you want to lock and then press Red key The selected channel will be marked with a lock symbol If you want to unlock the channel press Red key again ES Note To view a locked channel you have to input the password The default password is 0000 More information about password please refer to section 7 2 Delete This operation allows you to delete one or more unwanted programs Press A W PAGE PAGE keys to select a program Press Green key to delete it gt Rename 1 Select the channel that you want to lock and then press Blue key you can rename the c
8. gram Guide with now and next and 7 days events Channel search with automatic manual scan Various channel editing function favorite move lock delete Software upgrade through RS232 USB USB 2 0 support PVR JPG BMP GIF picture MP3 Standby consumption lt IW CVBS video and L R audio output 1 3Introduction 1 3 1 Lavout Of The Main Unit 5 6 7 8 1 Twin Antenna Input SMA connector 2 Ext Remote Sensor 3 AV Output a Video Output Yellow RCA b Right Audio Output Red RCA c Left Audio Output White RCA 4 Power Input DC12 24 Volts 5 Power LED 6 Remote Sensor 7 AV Output 8 USB Connector 1 3 2 Layout of The Remote Control Power Press to turn on off the DTV Mute Select sound or remove sound Enter Confirm the selection Displav Displavs current channel program information TV RADIO Switch between TV and Radio modes 0 9 Input channel number SUB Change the subtitle language EPG Displav the Electronic Program Guide AUDIO To change audio language TTX Display teletext features FAV add or remove TV channels from one of the four favorite channel lists Exit Menu exit and OSD clear VOL Volume adjust and left right in the menu Menu Display the main Menu CH Change the channel one by one and up down in the menu lt gt Menu select Search Scan program Play Pause Press to turn on off the Time shift Fomat To select usb mp3 play YELLOW
9. hannel name 7 2 Edit Radio Channels v Please refer to section 8 1 Edit TV Channels 7 3 Add TV Favorites From here you can add TV channels to or remove TV channels from one of the four favorite channel lists labeled with FAV1 FAV2 FAV3 and FAV4 1 Press A W keys to select the channel 2 Press Red Green Yellow Blue keys to add to or remove from list FAVI FAV2 FAV3 and FAV4 respectively For instance if a channel is added to list FAV1 it will be marked with the symbol Vi is similar to other FAV list Note One channel can be added to several lists The FAV list can be displayed by pressing the Red key when you are watching TV 8 Installation This chapter describes how to search for channels and a series of procedures 8 1 Automatic Search Press MENU key and then select Installation Automatic Search you will see Automatic Search interface as follows Here you don t need to enter any other information than press OK key and then it will automatically search all the channels 1 Press OK key to begin the auto search procedure If there are already some channels the receiver will ask if or not to carry out the procedure 2 Press OK key to stop the procedure at any time if you want to 8 2 Manual Search You can search single channel manually by searching parameters if you know the channel information gt Channel Number Press lt P gt key to move
10. mporarily and then you can set the program to formal status by press MUTE key again or press the keys 4 3 Program Information Program information is always displayed for a specific period of time whenever you switch channels You can view the detail program information by pressing the INFO key while watching a program and then press the EXIT key to hide it 1 General Information General Information is displayed as follows on the screen 1 Channel number and channel name 2 Progress bar 3 Icons amp Displayed only when the channel is locked Y Displayed only when the channel is in one of the FAV list Displayed when multi audio languages is available in this program TTX Displayed only when there is teletext in this program Displayed only when subtitle information is available 4 Now Current program name program begin time and end time 5 Next Next program name program begin time and end time 6 Current time 2 Detail Program Information You can see detail information about the current channel by pressing the INFO key Note Press the EXIT key to hide the information box 4 4 Channel List Three types of channel lists are provided for easy and quick channel switch TV list and RADIO list are list of TV and radio channels 1 Press OK key to display the TV list and then you can press lt P keys to switch to RADIO list and FAV lists or you can press F
11. nical specification 12 1 Introduction 1 1 Precautions Install correctly your new equipment will provide you with years of enjoyable and safe usage Installing this unit requires technical expertise This unit should be installed by a qualified technician or service personnel If you try to install this unit by yourself do it properly referring to the installation and wiring diagram ms in this operating manual Improper installation may result in fire or electric shock 1 Do not operate this equipment while driving safe driving should always be your highest priority 2 Do not install components in areas which are susceptible to rain moisture direct sunlight extremely heat or cold excessive dust dirt or humidity 3 Immediately unplug the power cord and send the monitor to your local dealer or service center as soon as possible a If there is sm ENTERe or any peculiar odor present during used b If there is damage to any of the internal components 4 To avoid damage to the unit and risk of electronic shock do not permit any of this equipment to become damp or wet from water or liquid If this does occur immediately unplug the power cord and send the unitr to your local dealer or service center as soon as possible 5 Do not attempt to repair open or disassemble any of the components Dangerous high voltages are present which may result in electric shock 6 Use only a power source with DC12 24 volts car battery negative ground 7 Do not
12. ntrol Check the battery of Remote control 12Technical Specification TUNER Frequency Range VHF UHF and L band Band 7 8MHz Switchable 12 Input impedance 75 Q CHANNEL DECODING Standard DVB T Demodulation COFDM FEC 1 2 2 3 3 4 4 5 5 6 7 8 Reed solomon 204 188 t 8 DEMULTIPLEXER Standard ISO IEC 13818 1 VIDEO DECODING Standard H 264 MP Level 3 0 MPEG2 MP ML MPEG 4 Aspect ratio 16 9 4 3 Video format PAL NTSC Video resolution 720x576 Max AUDIO DECODING Decoding MPEG 1 layer I II amp II MPEG 2laverl II amp II MPEG2 AAC MPEG 4 AAC LC HE AC3 Output mode Dual channel Stereo PROCESSOR CPU Hi3560Q Processor speed 270MHz Power Source DC12 24 Volts 0 5 Negative Earth Power Consumption lt SW Power on Less than 300 mW Power off Operating Condition 0C 70 C Board Dimensions 140 mm x 125 mm x 25 mm Weight 380 g NOTE Designs and specifications are subject to change without prompt notice Weight and dimensions shown are approximate JB
13. place or suspend objects on the power cord as this may damage the cord 8 Do not twist or place the power cord near any source of heat in the vehicle 10 Avoid dropping any metal objects or inflammable items into the unit ventilation slots 11 After the unit is installed do not arbitrarily pull it down or strike it This may loose the mounting screws and cause it fall down 12 Do not install your monitor where a it will obstruct the driver s view b it will obstruct the operation of the airbag system c it will obstruct the operation of the vehicle especially the steering wheel shift lever or brake pedal d a diver or passengers may injure themselves when getting into or out of the car 13 Do not damage any pipes tubes the fuel tank or electric wiring when installing this unit this can cause a fire if you drill a hole in car panels make sure that any hidden car parts will not be damaged 14 do not use any nuts or bolts for safety devices such as steering linkage fuel supply or braking systems this can cause a fire or an accident take care to prevent cords and wires from getting tangled or crimped in the moving portion of a seat rail 1 2 Main function Special design for car using support high speed above 160km hours Video decoder MPEG 4 H 264 AVC Audio decoder MPEG AAC PCM DVB subtitling ETSI 300473 compliant and OSD teletext Logic channel number Easy first installation Supports multiple OSD languages menu EPG Electronic Pro
Download Pdf Manuals
Related Search