Manual - Reich Benelux
Contents
1. Press the or button to reach the available capacity Each step is 0 5A more or less When you have reached the correct setting you can save this by pressing both buttons simultaneously for 2 seconds again The display will now indicate the actuall power If you move to another camping site or you need to reset please repeat steps a f When used normally the set maximum power consumption can be read by pressing the or button briefly The Fuse Control can be set to a maximum consumpiton of 10A is approx 2300 Watt If you want to take a higher amperage you need to do this without using the Fuse Control Ostensibly you can set higher amperages than 10A however these will not function When used more than 10A the device turns off automatically TOO HIGH CONSUMPTION When a too high power consumption Is reached the Fuse Control will turn off the power supply in the vehicle The display will indicated FF Turn off the last switched on device s and press the and button of the Fuse Control simultaneously and briefly to reset The Fuse Control will reset the power supply if you don t have switched on more 230V devices than the capacity available CALCULATIONS Volt x Ampere Watt In other words if the power connection Is 230V in most European countries and you have available 4A you can use 4 x 230V 920 Watt In this way you can always easily calculate the capacity of your electrical devices l TIPS2. 1 Fitting must be done by a qualified electrician 2 The Fuse Control is an electronic device treat this with care 3 Be carefull with moisture IVRA nederland Installation and Reich Benelux Office Delta 44 NL 6825 MS Arnhem Tel 31 0 26 384 4567 Fax 31 0 26 361 6773 E mail ivra reich web com Website www ivra nl User Manual FUSE CONTROL Reich GmbH Ahornweg 37 D 35713 Eschenburg Tel 49 2774 93050 Fax 49 2774 9305 90 E mail info reich web com Website www reichweb com Contents General O peration Connection Installation Use of the Fuse Control Too high consumption Calculations Tips NOU BWNEF ALWAYS KEEP THESE INSTRUCTIONS WITH YOUR CARAVAN Reich GmbH is not responsible or liable for any damage whatsoever caused by using the Fuse Control In event of any damage caused by a defect or production fault of the device we will only be liable to refund the purchase cost of the Fuse Control Reich GmbH reserves all rights to modify or alter the Fuse Control without prior notice It is illegal to sell export or re export the Fuse Control or a copy or adaptation of the Fuse Control to dealers in the USA and or Canada without written permission from Reich GmbH All rights reserved Nothing in this manual may be copied stored or published by means of print photocopying microfilm in any way either electronically or mechanically without the wri
3. 5A a Turn off all 230V devices in the vehicle b Set up the 230V connection on the camping site C The display of the Fuse Control will now light up d Push both buttons and simultaneously for approx 2 seconds The display will now flash
4. tten permission of Reich GmbH i G EN ERAL The Fuse Control is a device that switches 230V In case of damage or doubt regarding the correct operation of the device it should be turned off l O PERATIO N The device protects against overload of your electrical connection on the camping site The available amperage is usually limited A too high power demand in your caravan or motorhome gives you trouble and the camping owner inconvenience When the Fuse Control is used correctly it will switch of the power supply without loading the fuse on the camping site IN STALLATIO N The Fuse Control is permanently installed inside the caravan or camper in the incoming 230V power supply l CONNECTION Site post gt Earth switch gt Fuse Control i WIRING DIAG RAM Turn off the power supply O pen the Fuse Control Lead the incoming cable in the allocated opening Strip the cable 4mm max Connect the green yellow cable to the mass and the phase brown and the zero blue to the allocated connections 6 Proceed in the same way for the outgoing cable connection to all devices in caravan or motorhome Prevent under all circumstances that contact is being made with the printed circuit board U PUNBA 7 Close the Fuse Control 8 Connect the incoming cable to the power supply You can now use the Fuse Control USE Depending on the available capacity you set the Fuse Control Please proceed as follows Available 4
Download Pdf Manuals
Related Search