Theater Management Software V5.6 [v06]
Contents
1. e Connect to the library using an FTP Client and delete all content in the old path except the new library content WARNING do not delete the folder holding all the new library content That folder is the path you set in the first step create and configure a new library with the TMS 5 6 software Transfer reload content previously deleted during the cleaning stage e f you temporarily moved content you can now transfer it to the library through the TMS application 1 8 2 Method 2 with spare library This method uses a spare library to temporarily store converted content before it is copied back to the original library What has to be done e Configure the spare library as library and the old library as provider in the TMS e Ingest content from the provider old library to the spare library e Delete content from the provider old library e Configure the spare library as provider and the old library as library in the TMS e Ingest content from the provider spare library to the old library e Remove the provider spare library Configure the spare library as library and the old library as provider in the TMS e Make sure the spare library is connected to the content theater network e To configure the spare library as Library see appendix 2 1 How to configure a library e To configure the old library as Provider see appendix 2 2 How to configure a provider Inges2. This does not require additional hardware but it requires at least 50 free disk space If you want to keep more content on the library you can use the second method which requires a spare library during the operation A third method is proposed if you upgrade the old library to a new physical one You only need to apply one of the three methods Overview e Method 1 direct conversion e Method 2 with spare library e Method 3 swap to new library Method 1 direct conversion This method converts content directly on the library It requires 50 free disk space on the library to store the converted content What has to be done e Create and configure a new library with the TMS 5 6 software e Check the free disk space of the library e Ingest content already previously present on the library e Remove content already present before the migration e Transfer reload content previously deleted during the cleaning stage Create and configure a new library with the TMS 5 6 software e To configure the library see appendix 2 1 How to configure a library You must enter the configuration parameters of the new library The old parameters were saved in the configuration backup file see above in how to reintroduce the previous application settings K When creating the library be sure to set a specific path for the library This will allow you to identify what folder holds the content in the new format R5905178 04 Theate
3. case the TMS is not properly configured or connected Please contact your integrator Check every CineStore Solo G3 network configuration 0 x Hardware Serial Last Msg Gmt 7 27 2012 8 58 03 AM ETETA Hardware Vendor DC Hardware Product Solo Hardware Product Id SEngl55 Hardware Version 55 Hardware Serial SOLO G3 01305 Time Shift ms 34563 Software Name Software Version SOLO 5 5 4 Local Network Usage Remote Network Usage Content Content 172 30 7 55 Control Control 172 31 7 55 Perform this operation for every Solo G3 listed on the left e Select the Solo G3 SMS R5905178 04 Theater Management Software 18 12 2012 _ 4 1 TMS SOFTWARE Installation e Verify in the bottom right list if the both networks control and content are correctly configured Each local network must have a valid IP address on networks of the theater If it is not the case the SMS is not properly configured or connected Please contact your integrator communication tool PeerFinder is not up to date on the SMS The following file might need to be updated on the Solo G3 D CineStore app bin Rd3 Packages PeerFinder PeerFinder cfg xml For the complete procedure please refer to the CineStore Solo G3 documentation or contact support for assistance in configuring the SMS properly Note It is possible that the network configuration on the Solo G3 is correct but the configuration file of the e Repeat fo
4. upgrade the machine and then reintroduce progressively the KDM that are still valid In order to stop the automatic recovery process of the database we will take care to disconnect the SMS servers from the network during the completion of this operation R5905178 04 Theater Management Software 18 12 2012 _ 1 1 TMS SOFTWARE Installation What has to be done e Stop the TMS application and manually move all KDM to an USB media e Disconnect SMS servers from network e Perform TMS software V5 6 installation e Reconnect one by one the SMS servers e Ingest the KDM that are still valid and that was not regenerated by the SMS reconnection Necessary part e USB media not provided by Barco Stop the TMS application and manually move all KDM to an USB media Move all KDM from the machine to the USB media into a Support Windows account e Stop the server and restart into a support Windows account See appendix 2 3 Start into the Support Windows OS account e Connect the USB media to the server e Launch a Windows explorer Press simultaneously the keys Windows e e Go to the directory D CineStore data content kdm e Move all files and directories present in this directory to the UBS media The location on the USB media is not important You can put all to root directory or in a new directory e Check that there are no remaining KDM in the directory D CineStore data content kdm Disconnect SMS s
5. Exit pop up is displayed Close Application Q Close thea TMS application joes rot shutdown the seiver Restart Stop and rest art the TMS application Push on Restart button The application stop Keep down the Shift key on the keyboard during the server start up Continue the procedure described above in step 3 ee 2 4 How to check the free disk space of the library e Click on the Content Browser module button e Select the Central tab e The library present on the Plaza Catcher is displayed Its size and its total capacity in GB are displayed in the column named Disk usage R5905178 04 Theater Management Software 18 12 2012 _ 7 2 Appendix TMS 5 6 3 From Scratch CENTRAL 3 SCREENS INCOMING Name Disks usage GB B Content Browser _ All screens and library All screens Ss 2699 11176 R5905178 04 Theater Management Software 18 12 2012 _
6. Theater Management Software V5 6 Installation manual Theater Management Software V5 6 R595905178 06 BARCO 18 12 2012 Visibly yours Barco nv Entertainment Division Noordlaan 5 B 8520 Kuurne Phone 32 56 36 82 11 Fax 32 56 36 883 86 Support www barco com esupport Visit us at the web www barco com Printed in Belgium 1 1 1 2 1 TMS SOFTWARE Installation TMS SOFTWARE INSTALLATION About the TMS Software The TMS software is an application that offers a centralized management of all SMS libraries and providers in a theater This application is part of a set of programs called TMS software suite About this manual This manual describes the procedure and conditions for the installation of the TMS software version 5 6 Overview e Required configuration e Plan your TMS Software Installation e Clean up your library e Verify the network configuration of CineStore Solo G3 servers e Verify certificates e Install the software e Update the library e Providers configuration Required configuration Requirements The software can only be installed on a Plaza Catcher in version 5 5 4 or higher with the hardware upgrade kit installed update kit art nr R8762424k Installing this software on any other platform or on a Plaza Catcher in another version will not work Contact your provider to upgrade your Plaza Catcher to the proper version if necessary Note Updating a machine a
7. al vi Fead DeDeliveny lt phared folders H SO cDelivenM anagerIncoming E oF LibU ser Speed Limits Write IP Filter Delete Append Iv List gt Iv Subdirs A directory alias will 2 path Separate mi A If using aliases at the specified location Aliases must contain the full local one directory with the pipe character directory structures it will only confuse FTP clients 10 Press the add button and set the path to F DcDeliveryManager Incoming 11 Be sure that the Files and Directories checkboxes are as in the illustration above 12 Press OK to apply the changes 13 Start the TMS application e Start menu gt Logoff e Wait a few second the automatic logon and the startup of the application 14 Configure the Delivery Manager provider as a Provider See appendix 2 2 Use the following settings e Model Generic automatic content provider e Server Name Use the name you want e IP 127 0 0 1 e User DcDelivery e Password 123456 e Path leave blank Barco TMS 100 PLAYERS LIBRARIES UNIDENTIFIED Fame product protocot_ a gt inest type configuration status Add Provider Model server name IgG n gt Key N i m k ie IP User Password Path R5905178 04 Theater Management Software 18 12 2012 _ 3 1 TMS SOFTWARE Installation WARNING Though there is a model called XDC Delivery Manager Provider you must not
8. ater in order to release at least 50 of disk space R5905178 04 Theater Management Software 18 12 2012 _ I 1 TMS SOFTWARE Installation 1 5 Verify the network configuration of TMS and CineStore Solo G3 servers If the theater contains CineStore Solo G3 servers it is necessary to verify their network configuration What has to be done e Start the PeerFinder Visualizer e Check the TMS network configuration e Check every CineStore Solo G3 network configuration Start the PeerFinder Visualizer e On the TMS go to the following directory with Windows Explorer D CineStore app bin Rd3 Packages PeerFinder e Run the following file double click Rd3 Packages PeerFinder Visualizer exe e This will start the PeerFinder Visualizer Check the TMS network configuration ioi xi Hardware Serial Last Msg Gmt 7727 2012 8 58 54 AM PLAZA G3 00050 Hardware Vendor xDC SOLO G3 01305 Hardware Product Plaza Hardware Product Id PEngl52 Hardware Version 5 2 Hardware Serial PL424 G3 00050 Time Shift ms 0 5 5 4 PLAZALIGHT Local Network Usage Remote Network Usage Control Control 172 31 78 50 Content Content 172 30 78 50 The list on the left displays all detected servers on the network Select the TMS Verify in the bottom right list if the both networks control and content are correctly configured Each local network must have a valid IP address on networks of the theater If it is not the
9. b seems frozen the progress percentage doesn t change in 10 minutes you should abort the job Select the job and press the Abort button This action will allow the ingest process to continue When all other jobs are complete you can manually resume the aborted jobs use the retry button Do not use the clear all button before all jobs are done or you won t be able to resume the aborted jobs Remove the provider spare library e Remove the configuration of the spare library Select the spare library in the Providers panel and press Remove 1 8 3 Method 3 swap to new library Use this method to replace the old library with a new one Content will be converted during the copy to the new library What has to be done e Configure the new library as library and the old library as provider in the TMS e Ingest content from the provider old library to the new library e Remove the provider old library Configure the new library as library and the old library as provider in the TMS e Make sure the new library is connected to the theater network e To configure the new library as Library see appendix 2 1 How to configure a library e To configure the old library as Provider see appendix 2 2 How to configure a provider R5905178 04 Theater Management Software 18 12 2012 _ 1 9 1 TMS SOFTWARE Installation Ingest content from the provider old library t
10. ch SMS from the Management network e Unplug each SMS from the Media network A WARNING Make sure you unplug the SMS from the network and not the TMS R5905178 04 Theater Management Software 18 12 2012 _ D 1 TMS SOFTWARE Installation Perform the new version installation Place the setup file and its security key file in the usual update folder Connect a USB media with the installation file and its security key file to the server Wait a few seconds and press the exit button in the TMS application When the Logout panel appears push on the Update button The TMS application stops The installation procedure runs automatically This installation may take several minutes Note If the update does not start automatically please start the process manually by clicking START MENU gt Programs gt UPDATE After the installation the server and the TMS application restart automatically in the new version If this is not the case restart the server manually by pressing the reset button on the front panel At this point the TMS application starts in the updated version User accounts were preserved so you can log in the same way as in the previous version Some features were added or modified in this new version For a detailed explanation of user interface changes please refer to the TMS user guide available on the BarcoZone intranet and on the secured Partner Zone URL https my Barco com Registration is
11. endix e Fill the other fields according to the settings of the Library 2 2 How to configure a provider e Click on the TMS Configuration module e Click in the right tab Servers e Select the Providers panel e Click on the Add button LIBRARIES f UNIDENTIFIED 1 i 2 User Interface ee Name Product Protocol EZ Configuration Status 2 Modules Users Servers Cameras x TMS Configuration e You must use the Generic manua content provider model Add Provider wht Generic manual content provider W Server name 5 characters max IP User Password Path e Fill the other fields according to the settings of the Provider R5905178 04 Theater Management Software 18 12 2012 _ 2 Appendix 2 3 Start into the Support Windows OS account When the machine is stopped 1 Press the power button on the front face 2 Keep down the Shift key on the keyboard during the server start up 3 It takes a few minutes to the server to finish its start up phase starting the operating system verification of hard disks applications launching 4 The XP logging window is displayed Log On to Windows Does de M Herrani Conporaiion Password 5 Use the support login and his associated password provided by your integrator When the machine is already started 1 Push on power button in the upper right corner of the GUI 2 The
12. ername password ip For example if the username for FTP connection to the library is lib the password is 123 and the IP of the library is 1 2 3 4 you must type the address ftp lib 123 1 2 3 4 o Press enter o For each directory to delete select the directory and press the delete key e Restart the TMS server in the normal application mode o Start Menu gt Logoff o Wait a few second the automatic logon and the startup of the application Configure the spare library as provider and the old library as library in the TMS e Disconnect the spare library from the theater network This will protect the content during the next step e Remove the configuration of the spare library Select the spare library in the Libraries panel and press Remove e Remove the configuration of the old library Select the old library in the Providers panel and press Remove e Reconnect the spare library to the theater network e Configure the old library as Library See appendix 2 1 How to configure a library e Configure the spare library as Provider See appendix 2 2 How to configure a provider Ingest content from the provider spare library to the old library e Use the content browser to ingest the content from the provider to the old library e Check the Jobs module and wait for all jobs to complete It could take several hours depending on content size If a jo
13. ervers from network Due to the mechanism of DB recovery it is very important to disconnect all SMS from the network The automatic detection of missing KDM in the TMS would initiate an immediate copy of KDM from the SMS servers This large number of copy would block the TMS application e Unplug each SMS from the Management network e Unplug each SMS from the Media network Perform TMS software V5 6 installation e Place the setup file and its security key file in the usual update folder or e Connect a USB media with the installation file and its security key file to the server e Start the server in normal mode e Wait a few seconds and press the exit button in the TMS application e When the Logout panel appears push on the Update button e The TMS application stops e The installation procedure runs automatically This installation may take several minutes Note If the update does not start automatically please start the process manually by clicking START MENU gt Programs gt UPDATE e After the installation the server and the TMS application restart automatically in the new version If this is not the case restart the server manually by pressing the reset button on the front panel Reconnect the SMS servers one by one You must plug the previously disconnected SMS to the network and ensure their correct configuration The procedure may vary depending on the type of SMS R5905178 04 Theater Manageme
14. in one of these panels e Click on Modify button e Set the two IP address Management Media and valid de modification OK Save e f the server had appeared in the Unidentified panel it disappears and reappears in the panel Players after a few moments Check the Jobs module and wait for all jobs to complete It could take several minutes depending on the number of KDM transfers e When all jobs are completed repeated the process for the next SMS This procedure is complete when all machines on the network are configured and their KDM arrived on the TMS 5 6 Dolby SMS Indicative procedure for not supplied hardware by Barco e Plug all Dolby SMS on the Media and Management network e Set one Dolby SMS manually in the TMS configuration module e Check the Jobs module and wait for all jobs to complete It could take several minutes depending on the number of KDM transfers e When all jobs are completed repeat the process for the next Dolby SMS This procedure is complete when all machines on the network are configured and their KDM arrived on the TMS 5 6 Update the library About the updating procedure The goal of this procedure is to convert content on the library into a format that s compatible with the new version of the TMS There are three methods to update the library You must choose and apply one of the three methods The first method is a conversion of the content directly on the library
15. lready in version 5 6 is possible with this setup In this case the procedure is greatly simplified see above in the chapter 1 2 how to update a machine already in version 5 6 SMS recommendations If the theater contains CineStore Solo G3 SMS version 5 7 4 of the Solo application is recommended for full integration with the TMS Earlier version of the Solo SMS are supported with limited functionalities How to update a machine already in version 5 6 The following update procedure must be used only when you need to update a machine that s already in version 5 6 In this particular case and only in this case the rest of the procedure described in this document shall not be performed The applications settings and the content are preserved Particular case of a server already in version 5 6 Some servers have already been updated with the first issues of version 5 6 v5 6 x In this case the procedure is simplified because it is not necessary to convert content on the library into a format that s compatible with the new version v5 6 It has already been done The only constraint is a new function that automatically removes the unused KDM at startup This new feature increases the system performance in terms of speed and volume backup but sometimes unfortunately it blocks the application startup when the volume of KDM is too important Assuming that most KDM on the machine are often obsolete we will remove the entirety of the KDM
16. necessary Reintroduce the previous application settings Almost all previous configuration settings are removed during the installation Users certificates and licenses Lobby Eyes Lobby Theater R TMS are preserved The other parameters were saved in a file It is necessary to reintroduce them manually in the setup of the application Below are the steps you should follow in order to find these parameters In the Tools module click on Document viewer NOC Select TMS documents as the source Select the backup_V5 5_configuration html file In this file you will find all the necessary information to reintroduce the previous settings auditorium name SMS Libraries R5905178 04 Theater Management Software 18 12 2012 _ 1 TMS SOFTWARE Installation Document Viewer i Backup_V5 5_config A ees TMS Documents 5 Backup_v5 5_configuration htmi Auditorium Name BARCO TMS UPDATE E HTML File Version 1 072 Ko Auto Logoff Timeout 00 00 00 SMS Server List Short Name 001 Server Type 1 Ip Address 172 31 2 1 Library Server List Name SMART Ip Address 172 30 95 254 FTP Login outbox Ftp Path test112 SMB Login SMB Password Cameras List e You have to enter this information in the TMS configuration module The settings for the library in Library Server List are detailed in the next chapter Other setting
17. nt Software 18 12 2012 _ 1 TMS SOFTWARE Installation The procedure must be applied one SMS at a time Do not connect all SMS at the same time A large number of transactions would block the TMS application e Connect one SMS to the Media and Management network e Make sure it is automatically detected by the TMS after a few moments or set the SMS manually in the TMS configuration module if it is not a Doremi or CineStore SoloG3 server e Check the Jobs module and wait for all jobs concerning this SMS to complete It could take several minutes depending on the number of transfers required for updating e When all jobs concerning this SMS are completed repeated the process for the next SMS This procedure is complete when all machines on the network are configured and their KDM arrived on the TMS 5 6 Ingest the KDM that are still valid Use the TMS application to ingest KDM that are still valid on the USB media e Start the server in normal mode e Plug the USB media that contains the backed up KDM into the server e Ingest KDM For more information see the user manual The application will automatically select and ingest valid KDM eventually not yet copied during the reconnection operation of the SMS 1 3 Plan your TMS Software Installation Impact on the theater organization Because the cleanup installation and reconfiguration of your server may take several hours it is very important to carefully plan this
18. o the new library e Use the Content Browser to ingest the content from the provider to the new library e Check the Jobs module and wait for all jobs to complete It could take several hours depending on content size If a job seems frozen the progress percentage doesn t change in 10 minutes you should abort the job Select the job and press the Abort button This action will allow the ingest process to continue When all other jobs are complete you can manually resume the aborted jobs use the retry button Do not use the clear all button before all jobs are done or you won t be able to resume the aborted jobs Remove the provider old library e Remove the configuration of the old library Select the old library in the Providers panel and press Remove Providers configuration What has to be done e Connect the providers to the network e Configure the providers e Configure the Delivery manager Connect the providers Connect different providers such as satellite receivers third party library and other content providers to the network Configure the providers e Configure the content provider as Provider See appendix 2 2 How to configure a provider e Check the Jobs module and wait for all jobs to complete It could take several minutes depending on the number of CPL transfers Configure the Delivery manager Use the following procedure to install the Delive
19. operation The time required for the installation depends on the quantity of content already present on the Library During installation the TMS server is no longer operational You must ensure that the SMS have what they need to operate without the TMS specifically that they have all the necessary content for the planned playbacks 1 4 Clean up your library Why is important to clean up your library First it is important to remove the unused old DCP present on your Lib to improve performance Removing unnecessary content saves time during transfers copy process and improves data management on the machine Second after the installation process all the content on the library will be converted from the old version of TMS software to the new one The removal of unnecessary content speeds up this operation Finally if a swap or spare library is not used during content conversion 50 of free disk space is required on the library You must either use a second swap or spare library or free 50 of the disk space to allow the conversion Otherwise the conversion from the old to the new library will fail and you will lose all your content What has to be done Use the TMS application in order to e Clean up all your unused DCPs If a second library is not used e Clean up DCPs stored on the lib that are present on another source other lib SMS External HDD e f necessary temporarily move or delete some content that can be reloaded l
20. r Management Software 18 12 2012 1 TMS SOFTWARE Installation Check the free disk space of the library e To check free space see appendix 2 4 How to check the free disk space of the library K Note you must have at least 50 free disk space If that isn t the case you must remove some of the content or you can use the second library update method requires a spare library Ingest content already present on the library e Add a Generic manual content provider with the path set to lib root shares plazalib on Open E NAS previous encoded path on 5 5 X TMS configuration on smartjog See appendix 2 2 How to configure a provider e Transfer all content from this provider to the library with the content browser Check the Jobs module and wait for all jobs to complete It could take several hours depending on content size If a job seems frozen the progress percentage doesn t change in 10 minutes you should abort the job Select the job and press the Abort button This action will allow the ingest process to continue When all other jobs are complete you can manually resume the aborted jobs use the retry button Do not use the clear all button before all jobs are done or you won t be able to resume the aborted jobs e Delete the provider from the server configuration select the provider in the Providers panel and press Remove Remove content already presents before migration
21. r the next Solo G3 in the list 1 6 Verify Certificates 1 7 If the TMS does not contain the appropriate certificates it may not work after upgrade How to verify the certificates of the TMS are correct e Go to the following directory with Windows Explorer E CineStore app data ca certs e Verify that this certificate file is present where XXXXX is the serial number of the TMS XDC PLAZAG3 TMS V6 XXXXX_cert pem e Go to the following directory E CineStore app data ca private e Verify that this certificate file is present where XXXXX is the serial number of the TMS XDC PLAZAG3 TMS V6 XXXXX_prkey pem Note You will find the TMS serial number on the label at rear of the server or under the icon at the top left of the desktop computer name g Plaza G3 00079 If the certificates are not present or if the serial number does not match contact your integrator Install the software What has to be done e Disconnect SMS from network e Perform TMS software V5 6 installation e Reintroduce the previous application settings automatically saved in a backup configuration file e Connect and configure SMS Disconnect SMS from network Due to performance reasons during installation of the new version it is very important to disconnect all SMS from the network The automatic detection of these machines during installation would result in the execution of a large number of KDM transfer process e Unplug ea
22. ry Manager 1 Go to the following directory with Windows Explorer C Program Files FileZilla Server 2 Run the following file double click FileZilla Server Interface exe 3 This will start the FileZilla Server Interface application It will show as an FZ icon in the Windows System Tray on the bottom right of the screen 4 Double click on that icon to open the application 5 Inthe top menu click on the Users icon This will open the user configuration window FileZilla server File Server Edit F Gl BE R leer C x tim kKosse filezilla project org Connecting to server Connected waiting mW Logged on K Retrieving account settings Done retrieving account setti 6 Press the Add button to create a new user R5905178 04 Theater Management Software 18 12 2012 1 LibL ser Speed Limits IP Fite mw Add user account E i Dedevey oo none o O 7 Setthe name to DcDelivery and the group to lt none gt Press OK 8 Enable the password and set it to 123456 DcDelvery Shared folders eeeesee neeeeesseeee LibUser Speed Limits i P Filter FTF user to access incoming Files From the Delivery Mana 9 Select the page named Shared folders R5905178 04 Theater Management Software 18 12 2012 1 TMS SOFTWARE Installation 12 1 TMS SOFTWARE Installation Page Shared folders Users Files 3 Gener
23. s are straightforward For more information refer to the user guide available on the BarcoZone intranet and on the secured Partner Zone URL https my Barco com Registration is necessary Mag messages LOGS Connect and configure SMS After installing the new version you must plug the previously disconnected SMS to the network and ensure their correct configuration The procedure may vary depending on the type of SMS Doremi and CineStore Solo G3 SMS The procedure for Doremi and CineStore SMS must be applied one SMS at a time Do not connect all SMS at the same time e Connect one SMS to the Media and Management network e Make sure it is automatically detected by the TMS after a few moments e Check the Jobs module and wait for all jobs to complete It could take several minutes depending on the number of KDM transfers e When all jobs are completed repeated the process for the next SMS This procedure is complete when all machines on the network are configured and their KDM arrived on the TMS 5 6 Doremi ShowVault SMS e Connect one Doremi Showvault SMS to the Media and Management network e Make sure it is automatically detected by the TMS after a few moments There are two possibilities The SMS appears in the Players panel Orin the Unidentified panel R5905178 04 Theater Management Software 18 12 2012 _ 1 8 1 8 1 1 TMS SOFTWARE Installation e Select the newly detected SMS
24. t content from the provider old library to the spare library e Use the content browser to ingest the content from the provider to the spare library e Check the Jobs module and wait for all jobs to complete It could take several hours depending on content size If a job seems frozen the progress percentage doesn t change in 10 minutes you should abort the job Select the job and press the Abort button This action will allow the ingest process to continue When all other jobs are complete you can manually resume the aborted jobs use the retry button R5905178 04 Theater Management Software 18 12 2012 _ I 1 TMS SOFTWARE Installation Do not use the clear all button before all jobs are done or you won t be able to resume the aborted jobs Delete content from the provider old library Once all transfer jobs are complete all content on the provider can be deleted This operation must be done with the Windows OS because the TMS application cannot delete content on a provider h Note Alternatively to the following procedure you can use a FTP client or the library web interface on a laptop connected to the theater network e Stop the TMS application and restart into Windows OS account See appendix 2 3 Start into the Support Windows OS account e Use Windows Explorer to delete the old library content o Press Windows E to open a new explorer window o in the address bar type ftp us
25. use that model Be sure to use the model called Generic automatic content provider 15 Click on OK 16 Click on Apply changes 17 Use the Providers panel to display the new provider and his configuration status Online Barco TMS 100 PLAYERS LIBRARIES PROVIDERS UNIDENTIFIED 5 Hian a an a Cameras R5905178 04 Theater Management Software 18 12 2012 14 2 APPENDIX Overview e How to configure a library e How to configure a provider e Start into the Support Windows OS account e How to check the free disk space of the library 2 1 How to configure a library e Click on the TMS Configuration module e Click in the right tab Servers e Select the Libraries panel e Click on the Add button Digital Theater PLAYERS PROVIDERS UNIDENTIFIED TMS Configuration e You can create a predefined Library or a Generic Library Add Library 5 SmartJog Library 12TB Server name a 5 characters max IP User Path OK x a CANCEL R5905178 04 Theater Management Software 18 12 2012 Ge progict protocol 10 configuration statu Browser d Model Server name IP User Password Path Disk Size 2 Appendix XDC Maintenance 2 55 PM i 15 2011 C Power User Thursday September Add Library Modules Users Servers Cameras Generic Library Ee 5 characters max 2 App
Download Pdf Manuals
Related Search