Y1 Manual
Contents
1. To switch the machine back on press one of the two buttons Before switching off the machine we recommend running about a cupful of hot water through the brew group with the capsule compartment B empty To switch the machine off move the main on off switch M into the 0 position never disconnect the plug from the power outlet when the machine is switched on CUP STAND ADJUSTMENT The machine is designed to be used with either mugs or espresso cups To adjust the height of the cup stand H you must remove it by pulling it out and then set it in the mug or espresso cup position Optimal position for espresso size cups Note the height of the cup stand H must be adjusted before you start dispensing coffee 19 MAKING COFFEE The machine is designed to make coffee exclusively with illy Metodo Iperespresso capsules Other types of capsules cannot be used as they could da mage the machine Make sure that the buttons and KC are steadily lit Unlock and lift the opening lever A of the capsule compart ment B Note if a capsule is present in the compartment B it will be automatically expelled when the compartment is opened The capsule must slide easily into the compartment if this is not the case take it out and reposition it correctly Lower the movable part of the top of the machine completely and press the lever A until you hear it lock in2. tervals The long espresso but ton will flash alternately At the end of rinsing the buttons and will light up steadily and an audible signal will be emitted to confirm that the machine is ready for use WARNING If descaling is not carried out the buildup of limescale could cause malfunctions not covered by the warranty When descaling for the first time it is recommended to use the descaling product supplied with the machine Do not use vinegar lye salt or formic acid because they may damage the machine Use only descaling agents suitable for coffee machines The descaling solution must be disposed of in accordance with the applicable laws and regulations Do not drink the liquid dispensed during the descaling pro cess the machine can be used to make coffee when the descaling process is finished If the descaling cycle is interrupted due to a power failure or because the machine is switched off by mistake the entire operation must be repeated before the machine can be used WARRANTY LIMITATIONS The warranty does not cover damage or malfunctions caused by Failure to carry out periodic descaling Operation with a voltage that differs from the rating shown on the data plate D see machine parts Improper use or use that is not compliant with the instruc tions Internal modifications The warranty does not cover the costs of repairs on machines previously handled by non authorized servic
3. place Position the cup on the cup stand H Press one button only the CZ button to brew an espresso coffee the C7 button to brew a long espresso When the coffee has reached the programmed level in the cup brewing will stop automatically 20 Note The pre programmed volume for each button has been set with the aim of satisfying the majority of users The brew setting for each button can be adjusted accor ding to personal taste by following the instructions in the paragraph below Warning The capsules are single dose and cannot be used to make two coffees Remember to clean the drip tray I and empty the used capsule container G Remember to change the water in the tank frequently ADJUSTING THE QUANTITY OF COFFEE IN THE CUP The machine allows you to set the desired quantity volume of coffee in a cup for both brew buttons and OP Note for the sake of simplicity we will illustrate only how to program the espresso button gt to program the long coffee button you must carry out the same steps but press the latter button and use a suitably sized mug To adjust and program a personalized quantity of coffee to be brewed proceed as follows Insert a capsule in the compartment B Place an espresso sized cup on the cup stand H Touch the espresso button and keep it pressed until reaching the desired quantity of coffee Then release the button The machine is now programme
4. 14 GENERAL OPERATING INDEX RULES E GENERAL OPERATING RULES enn 14 Carefully read the instruction manual and warranty limitations m TECHNICAL DATA sse 14 The machine must be connected m OMACHINE PARTS 15 to a grounded power outlet The machine must be kept clean m IMPORTANT SAFEGUARDS 16 by frequently washing the cup stand USING THE ESPRESSO MACHINE s 16 the drip tray the capsule holder NSTALLATION OF THE ESPRESSO MACHINE 11111 16 the tank and the glass cup holding surface CLEANING THE ESPRESSO MACHINE 111111 tttteteee 16 Maintenance may only be performed while NUAGE OF MALFUNCTIONING the machine is off MPROPER USE OF THE APPLIANCE IMPORTANT never immerse the machine m INSTALLATION AND START UP OF ESPRESSO MACHINE 17 or its removable components in water or put it in the dishwasher E TUBNINGONJOFE cire terrere mn 18 POWER SAVE iss cue ehe e e 18 The water contained in the tank must be replaced regularly W CUP STAND ADJUSTMENT e 19 Do not use the machine if the tank is empty We recommend descaling the machine at least every 2 months using a descaling m ADJUSTING THE QUANTITY OF COFFEE IN THE CUP 20 agent made especially for espresso machines E MAKING COFFEE cerit tette en senserit 19 oon W CLEANING AND MAINTENANCE s 21 See instructions in the De
5. cal ing procedure touch the button within 5 seconds and release it when you hear the beep 5 The button will remain steadily lit 6 To start the descaling cycle touch the button within 5 seconds to deliver the solution of water and descaling agent 22 IMPORTANT If these steps are not carried out within the times speci fied the machine will switch back into the coffee mode To carry out a descaling cycle repeat steps 1 to 6 For about 10 minutes the machine will carry out a descaling cycle delivering the solution of water and descaling agent at regular intervals The espresso button will flash alter nately When the solution of water and descaling agent runs out the long espresso button will remain steadily lit to indicate that it is ready to begin the rinse cycle Remove the water tank L empty the residual water with descaling product Rinse it out thoroughly under running water and fill it with fresh drinking water Fit the tank L back in the machine until it is inserted cor rectly in place Empty the container and place it back under the brew group C WARNING do not reuse the water with descaling agent contained in the collection container to avoid impairing the machine s performance The long espresso button will be steadily lit W Touch the button KZ to start the rinse cycle For about 5 minutes the ma chine will carry out a rinse cycle dispensing water at regular in
6. cating that the second part of the descaling cycle is in prog ress Water is being run through the machine to rinse out the circuit The long espresso button alone flashes progressively The machine has a malfunction Turn it off and back on again after 30 seconds If the fault is signaled again contact a service center PROBLEM The machine does not turn on The machine does not dispense coffee Water leaks out CAUSE The power supply cable is not plugged in to the power socket 25 SOLUTION Connect the plug to a power outlet meeting the technical specifications given on the data plate D The main on off switch M is po Sitioned on 0 No water in the tank Position the main on off switch M on I Fill tank L with water The capsule is not inserted in the capsule compartment Insert a capsule in the capsule compartment B The capsule inserted does not dispense coffee After one unsuccessful brewing attempt with the same capsule inserted properly in the capsule com partment B lift the lever A the capsule will be expelled close the compartment to dispense a small amount of water reopen the compartment A in sert the capsule again lower the top until it locks in position and touch the or C7 button If coffee is not dispensed discard the capsule The moveable part of the top of the machine is not completely closed Lift the lever A and make s
7. d the next time you press the espresso button the machine will brew the quantity you have just programmed The programming replaces the factory settings MANUAL STOP You can stop brewing coffee before the automatic stop by again pressing the button you just selected Warning in any case brewing will stop automatically after a preset maximum time of about 70 seconds In this case coffee could overflow from the cup CLEANING AND MAINTENANCE The machine and its components must be cleaned at least once a week Do not use the water left in the tank L for some days wash the tank and fill it daily with fresh drinking water Do not use ethyl alcohol solvents abrasive sponges and or ag gressive chemicals To clean the machine proceed as follows Switch the machine off and disconnect the plug from the power outlet Remove the water tank L and lid and wash them under run ning water Remove the cup stand H and the drip tray I and wash them with warm water t Ei Nig Remove the used capsule con tainer G by pulling it out 21 I Empty out the container Caution used capsules and some liquid residue from the cof fee extraction will be in the tray Note when fitting the used capsule container G back in place make sure it is inserted correctly We recommend emp lying out the drip tray I and used capsule container G at the same time Caution do not dry the mach
8. e brewing coffee Never open it while Coffee is being dispensed Note When using the machine for the first time or after it has not been used for 7 or more days after placing a container of suitable capacity beneath the brew group C we suggest running at least half a tank of water through the brew group without inserting a capsule TURNING ON OFF To turn on the machine proceed as follows Check the water level in the tank L if necessary add water as previously described Move the main on off switch M into the I position The but tons CZ and will light up repeatedly from left to right This indicates that the machine is starting to warm up Wait until the buttons 5 and are steadily lit and the machine emits a beep this indicates that the machine has reached the correct operating temperature Touch the button Wait until water flows out of the brew group The machine will automatically stop dispensing water when the programmed quantity has been reached or you press the buttons on the touch screen again Note Only during the initial warming up phase the machine will not brew coffee if the buttons and are off or flash ing Power Save The machine has been programmed to protect the environment and save energy when it is not being used When it has not been used for 60 minutes the machine will switch automatically into the Power Save mode the button will flash slowly
9. e centers Such costs will be borne entirely by the machine owner It is recommended not to place the drip tray I in the dishwasher to keep the drip tray and used capsule container clean Failure to observe these instructions may cause damage to the machine which is not covered by the warranty WARNING It is advisable to keep the original packaging at least for the duration of the warranty period in order to ship the machine to a service center for repair if necessary Any damage caused by transport without adequate packa ging will not be covered by the warranty 23 Disposal of end of life electric and electronic equipment by private households in the European Union The WEEE symbol used on this product means that it must not be disposed of together with other domestic waste and should be collected separately Consumers have the opportunity to hand in their used appliance to distributors free of charge on a 1 1 basis when they purchase a new product For further information about the collection of appliances to be scrapped please contact the local authority in your town of residence the local waste disposal service or the retailer where the product was purchased Consumers are responsible for disposing of end of life appliances in accordance with the current provisions of law and noncompliance therewith may be subject to fines and criminal sanctions The correct disposal of this product will contribute to prot
10. ecting the environment natural resources and human health C qp I Intertek INDICATION 24 MACHINE STATUS INS gt feed gt feed E53 The buttons light up in sequence EEJ lt Lit zo WA The espresso button flashes The long espresso button flashes Slow flashing Ep Ep MEC aes Dimming of illumination Steadily lit only the espresso button en ea Flash alternately Steadily lit only the long coffee button CEI CEI Flash alternately Rapid flashing The machine has been turned on and is warming up The machine has reached the right temperature for brewing The machine is brewing an espresso An espresso is being programmed The machine is brewing a long espresso A long espresso is being programmed The machine is in the Power Save mode The machine switches into Power Save after 60 minutes when not used To start the machine again just touch any button The machine needs to be descaled The machine is indicating that the descaling cycle has been selected In this status the tank should contain a descaling solution The machine is indicating that the first part of the descaling cycle is in progress Descaling solution is being run through the machine The espresso button alone flashes progressively The machine is indicating that the first part of the descaling is over The tank must be rinsed out and filled with fresh drinking water The machine is indi
11. er and therefore dangerous Unplug the power cord from the electrical socket when the machine is not in use Do not touch hot surfaces The water coffee dispensed from the machine may cause burns This machine is manufactured to make espresso coffee use care to prevent scalding due to water jets or any im proper use of the machine The machine is not designed to be used by people includ ing children with limited physical mental or sensory abili ties or insufficient experience and or skills unless they are supervised by a person responsible for their safety who provides instructions on how to use the appliance Children must be kept under supervision to prevent them from playing with the appliance The machine is intended for indoor use only To protect against fire electric shock or personal injury do not immerse the cord plug or the body of the machine in water or any other liquid Do not place the machine on or near electrical or gas burners or inside a hot oven The machine must be turned on only when being used After use it must be turned off by moving the main on off switch M to the 0 position and disconnecting the plug from the power outlet Before unplugging the machine make sure that the ON OFF switch M is in the 0 position Using attachments not recommended by the manufacturer may result in fire electric shocks or personal injury a Do not let cable hang from the
12. from water taps and sinks After removing the packaging check that the appliance is in perfect condition before installation Do not leave the packaging materials within children s reach Cleaning the espresso machine Before unplugging the machine check that the main on off Switch M is in the 0 position Unplug the machine before cleaning Wait until the machine is cool before cleaning Remove the water tank L by pulling it up slightly and then outward IMPORTANT SAVE THESE INSTRUCTIONS Clean the body and attachments with a wet cloth and then wipe with a non abrasive dry cloth Do not use detergents Do not expose the machine to extended jets of water or immerse it in water partially or fully In case of malfunctioning Do not use the appliance if the cord or plug are damaged or if the appliance shows signs of malfunctioning or has been dam aged in any way Take the machine to the nearest authorized service center for checks or repairs If the power cord is damaged it must be replaced by the manu facturer or an authorized service center In case of damage or malfunction turn off the appliance and do not tamper with it For repairs contact a service center au thorised by the manufacturer and request the use of original spare parts only Failure to comply with these instructions may compromise the safe operation of the machine and will result in the forfeiture of warranty rights Improper use of the appl
13. iance This appliance is intended for household use only Any oth er use is to be regarded as improper and thus dangerous The manufacturer is not liable for accidents caused by non compliance with existing legislation on electrical grounding systems The manufacturer is not liable for possible damage caused by improper incorrect or unreasonable use This appliance is intended to be used in household and similar applications such as Staff kitchen areas in shops offices and other working en vironments farm houses hotel in room motels and other residential type environ ments bed and breakfast type environments 17 INSTALLATION AND START UP OF ESPRESSO MACHINE Before connecting the machine to a power supply carefully read the safety instructions given in the chapter important safeguards Remove the water tank L from the machine by pulling it slightly up and then out Lift the tank lid Fill the tank with fresh drinking water until the MAX mark is reached CAUTION always fill the tank with fresh still drinking wa ter only Hot water or other liquids may damage the tank Do not use the machine without water After setting the lid back in place insert the tank all the way into the machine Insert the plug into the outlet Consult the following chapter to switch on the appliance Warning make sure that the capsule compartment B is properly closed befor
14. ine and or it components in a microwave or conventional oven RECOMMENDATIONS To enjoy a high quality espresso remember to Change the water in the tank at least once a week f possible use water with a hardness of less than 12 French degrees to reduce the deposits inside the machine Used warmed cups DESCALING The formation of limescale is a natural consequence of using of the machine Descaling serves to optimize cleaning and remove limescale buildup from inside the machine When descaling is necessary this will be indicated by a dim ming of the buttons icons every 10 seconds Use descaling products that are not excessively aggressive To descale the machine you can use any commercially avail able non toxic descaling product for coffee machines To descale the machine proceed as follows Remove the water tank L and empty out the residual water Fill the tank with 0 7 litres of fresh drinking water Add the descaling agent and wait for it to dissolve stir to make the product dissolve faster Check that there are no capsules in the capsule compartment B Place a container with a capac ity of at least 1 litre beneath the brew group C 1 Switch on the machine 2 Within 15 seconds press the button and release it after 7 seconds when you hear the beep indicating entry into the descaling program mode 3 The CZ button will flash alternately 4 To confirm the des
15. scaling chapter The machine is fitted with a valve E RECOMMENDATIONS enn 21 that maintains constant pressure e DESA N itn o eddie En 22 for this reason some water may drip from the brew group HE WARRANTY LIMITATIONS s 23 W INDICATION MACHINE STATUS 24 I IBOUBLESHOOTING cerei rat ters 25 TECHNICAL DATA Casing Aluminum Voltage 230 V 50 Hz EU 120 V 60 Hz USA Heat exchange material Stainless steel Power 1250 W EU USA With Power Save function Water tank 0 7 liters 24 oz Electric cord length 1 5 m 59 inch Used capsule container capacity 7 capsules Size W x D x H 240 x 240 x 275 mm 9 4 x 9 4 x 10 8 inch Pump 19 bar Weight without packaging 7 5 Kg 265 oz The manufacturer reserves the right to make changes or im provements without notice MACHINE PARTS A mmo o Uu LEVER TO OPEN CLOSE CAPSULE COMPARTMENT CAPSULE COMPARTMENT internal BREW GROUP DATA PLATE on base CUP HOLDING SURFACE LIGHTED TOUCH SCREEN F1 ESPRESSO F2 LONG ESPRESSO E zar USED CAPSULE CONTAINER residual liquid after brewing CUP STAND DRIP TRAY internal WATER TANK MAIN ON OFF SWITCH POWER CORD 16 IMPORTANT SAFEGUARDS When using electrical appliances always follow the safety pre cautions below Using the espresso machine Read all Instructions This machine is intended for household use only Any other use is considered improp
16. tables or counters Do not pull the plug out by the cable and never touch it with wet hands Do not carry or pull the coffee machine by the cable To reduce the risk of injury do not drape cord over the counter top or table topwhere it can be pulled on by chil dren or tripped over unintentionally Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment Do not use extension cables or power strips In case of fire use carbon dioxide CO Do not use water or powder extinguishers Never obstruct the ventilation openings on the base of the machine Do not use appliance for other than intended use Installation of the espresso machine Read the instructions carefully Do not install the machine in an area where the tempera ture may reach O C 32 F or lower if water freezes the appliance may be damaged or higher than 40 C 104 F Check that the mains electric voltage corresponds to the requirements indicated on the machine data plate D Connect the machine only to a properly grounded power outlet with a minimum rating of 6A for models powered at 230Vac and 15A for models powered at 120Vac If the plug and the outlet are not compatible have the plug replaced with a proper one by an authorized service center Place the machine on a countertop away
17. ure that a capsule has been inserted into the capsule compartment B Lower the lever A again with some force as far as it will go Keep touching until you feel the lever A lock and press the X or T button The or button has not been pressed The water tank has not been cor rectly inserted Touch the or button again Insert the water tank L completely into the ma chine until it clicks firmly into place Internal components with scale buildup Descale the machine as described in the related paragraph The pump did not prime Incorrect type of capsule Machine in power save mode Check that the capsule compartment B is empty of capsules lower the lever A into the locked posi tion and touch the CZ or button to dispense water Try again to brew a coffee with a capsule Make sure that you have used an illy Metodo Iper espresso capsule Make sure to use capsules for domestic use identified by the wording Single serve ground coffee capsules for domestic use which appears on the package and not capsules for professional use identified by the wording For professional use only Start the machine by touching a coffee button and wait until it is ready to brew when both coffee but tons are steadily lit Touch the or CZ button again to start brewing If problem persists Contact an authorized Service Center
Download Pdf Manuals
Related Search