Royal Care Series
Contents
1. the button when the figure reaches the desired time and is set as the working time for the system The system is automatically shuts off when the set time expires or 45 minutes is up default system time O EJ Chromatherapy This button controls the color of the Chromatherapy LED lights picture 5 When the Chromatherapy function starts the lamp symbol on the LCD display flashes 9 Circulation Fan This button turns fan on off When fan is turned on the fan symbol on the LCD display Flashes OP m Steam on off This button turns the steam on off Touching this button makes the steam symbol on the LCD display flash The temperature sensor regulates steam output based on the preset steam temperature The steam generator has 4 C variance between accrual set temperature and real temperature A Music on off This button turns music on off CD FM Radio on off Touch this button and the radio station will show on the display The FM radio is now on The radio freguency by default is the same as the radio freguency selected last time Note if the MP3 shows on the display the radio will not play Touch the FM radio button again 8 Volume amp Frequency Adjust e Volume i Touch this button when the FM radio is on Push ZLA to adjust the volume Display will show DB e Frequency Touch this button when the FM radio is on Push the VIIA again to adjust the frequency Display will show MHZ 13 Page Rev 10 2012 Chann2. 661 9 Page Rev 10 2012 INSTALLATION INSTRUCTIONS FOR WS102 amp WS105 1 Level the tray with the level 2 Make sure all the adjustable feet are touching the ground and supporting the base 3 Connect the drain if building the unit in its final resting place Note This unit can be built from the inside 4 Assemble curved horizontal rail to left and right vertical rails using ST4X40 screws 5 Attach the door frame to the base using ST4X40 Screws SEA on EA 5 Pr oj V o 6 Use ST4X20 screws and covers to attach the vertical rails to the base skirt 7 Attach the chrome trim to the base 8 Install the shower bar on the right side back panel using hardware enclosed in cloth bag Install shampoo holder onto the left black back panel using M4X25 caps nuts bolts and O rings 9 Inspect and tighten the body jets and hoses if necessary 10 Install the left and right side black back walls 12 Bring main center panel inside the unit 13 Connect water supply lines to the water manifold Connect side panel water jets to the manifold then connect the power supply 14 Attach center panel to right and left side panels with ST4X16 screws A ti 6 Page Rev 10 2012 INSTALLATION INSTRUCTIONS FOR W5102 8 WS105 15 Connect fan light and radio wires to the roof Install the roof of the shower cabin using ST4X12 screws 16 Install the sliding doors Spring loaded rollers go on the bot
3. ERENT DRAIN SYSTEM FOR THE SHOWER IS USED THE STEAM GENERATOR MUST A HAVE DRAIN CONNECTION AVAILABLE TO DISCHARGE THE WATER INTO THE MAIN SHOWER DRAIN A g OD STUB MUST BE ADDED TO THE MAIN SHOWER DRAIN TO CONNECT THE STEAM GENERATOR DRAIN OUTLET Note Within the Warranty period please don t take off the decals from the computer control boxes and the steam generator without manufacturer s permission Have only licensed professionals install or perform any maintenance Generally our technicians can troubleshoot most problems over the phone When calling for service questions please provide your model number serial number Purchase Order and type of problem you are having TOOLS REQUIRED FOR INSTALLATION Level a HERE Orn Screw driver 42 Phillips Ar Silicone i So G Cc CR o Wrench Electric Drill f RS Sguare Ruler oS Rubber mallet 3 Page Rev 10 2012 PRODUCT FEATURES DESCRIPTION WS102 WS105 WS109 WS115 3kW Quick heating Self Draining Steam Generator v v v v Steam Aromatherapy Cup v v Body Massage Jets v v v v Hand held Shower w Various water massage settings 8 adjustable height bracket v v v v 8 inch 203mm wide water drenching Rainfall Shower v v v v Thermostatic Anti scald Faucet v v v v Strengthened Black Back Tempered Glass walls v v v v Clear Glass Front amp Doors v v v v Polished Aluminum Trim v v v v Glass Touch no seam Control Panel v v v v Complete media center with FM Radio v v v v Wi
4. ch male national pipe thread not included Install shutoffs where they can be accessible e Access panel near controls pumps and jets is recommended e Drainage It is advised to have base onsite before preparing drain location The diameter of the drain hole should be larger or equal to 40mm 1 6 inches e Note The flexible drain hose included with this unit is for installation into a floor drain only Substituting the existing drain setup for a setup of the installers choice will not void the warranty of the unit as long as there is no evidence of misuse or damage to the base If the substitute drain system is used a 3 8 in stub must be added to the main shower drain line to connect the steam generators automatic flushing drainage hose e All fixtures and fittings must be checked for tightness as they may have been loosened during transport GENERAL INFORMATION e Connect hot and cold supplies and all electrical just before unit is set into place e Units come broken down in panels and are assembled with screws nuts and bolts on site Note All shower bases need to be leveled in its final resting position all feet must be touching the ground mark the placement then pull base out and begin assembly e tis advised to have base onsite before preparing drain location Access panel near controls panel and jets recommended e Manufacturer reserves the right to change specs or features at anytime Please check to confirm details 1 866 783 2
5. ease decrease for transmitting frequency for FM The adjusting range is 88 108 8MHz O selected ID Transmitting channel memory push and hold this button to memorize this channel after the transmitting frequency is Transmitting channel adjusting push this button to select the transmitting channel from memory up or down Note 1 Make sure not to select transmitting frequency which is the same as the existing FM radio frequency because it will not transmit 2 The wireless FM transmitter should be placed far away from any other wireless transmitting device 15 Page Rev 10 2012 TROUBLESHOOTING FOR STEAM CABIN 1 Not connected properly Check connection between contro panel Touch panel does not work and power box 2 Wrong voltage Change to 220V supply 1 Desired steam room temperature is Increase the desired temperature to be lower than current temperature higher than current temperature 2 The water inlet valve not letting water Check water inlet valve for blockage and 12V power supply to valve in 3 The water level sensor is not working Clean scale of the water level sensor or water coming out steam outlet replace it No steam 4 Thermal switch in the heater is not Change thermal switch installed inside the working no steam from generator heater 5 The heater is not working Change the heater 6 The water supply is shut off Open water valve 1 The water inlet electromagnetic valve Replace water inlet va
6. el Memory e Channel Memory Setting o Start FM Radio o Set serial number touch button and touch button again fissure from 1 to 8 shows circularly stop touching this button when the wanted fissure shows o Adjust FM Radio to your favorite channel touch button to adjust frequency and volume o Channel Memory Touch button for more than 3 seconds the figure shows 1 and turns to original setting Station number Release button to finish setting for one channel If the station number is used for another channel this channel will be replaced by the new channel in memory o Repeat the above steps to save channels in memory Maximum 8 channels can be memorized e Find Channel o Start FM Radio Touch button to find right channel in memory A adjust v adjust o The above 2 buttons are used to adjust frequency and volume 14 Page Rev 10 2012 WIRELESS FM TRANSMITTER Audio Signal Input On off USB Interface Transmitting Frequency adjusting Transmitting Frequency adjusting Transmitting Channel adjusting Transmitting Channel Memory Transmitting Channel adjusting 4 On Off Push and hold this button for power on off Push and release this button shortly to change between transmitting and clock Audio signal input to be connected to audio signal output interface of Mp3 player AV Transmitting frequency adjusting push this button to incr
7. ft cloth and non abrasive cleaner or heated vinegar 3 After every 30 times of using the unit we suggest you to clean the steam generator We advise the use a filtration system for the steam generator unit One Compatible filtration system option is the Whirlpool WHKF DWHV STEAM GENERATOR CLEANING FOR ALL UNITS Remove the cover of the cleaning liquid inlet and pour in approximately 1L of citric acid or white vinegar Start the steam function to fill the steam generator with water Stop the steam function before the steam starts to come out acidic steam is damaging to plated fixtures Do not shut off the main power The scale in the steam generator dissolves and the system drains the dirty water out after 60 minutes GENERAL USE AND MAINTENANCE FOR ALL UNITS A Drops of water will continue to drain out from the jets and water outlets after use this is normal and it will eventually stop B Abrasive cleaners must not be used C Always shut off the power supply when the system is not in use 10 Page Rev 10 2012 CONTROL PARTS INFORMATION FOR STEAM SHOWER FOR ALL UNITS 1 Steam Temperature Sensor 2 LCD Display 3 Control Panel 4 Water Diverter 9 5 Water Flow Adjustment On Off 6 Water Temperature Adjustment T Body Jets D R 8 Steam Outlet 9 Handheld Shower Set 10 Steam Generator Cleaning Liquid Inlet 11 Page Rev 10 2012 LCD DISPLAY 2 1 Fahrenheit Degree if applicable 2 Ce
8. lsius Degree o 3 Temperature 4 4 Temperature Indicator 9 Time Setting 6 FM Radio Frequency 7 FM Radio Volume 5 8 FM Radio Channel 9 Chromatherapy on off 10 Circulation Fan on off i 11 Steam on off 12 Power on Indicator 13 FM Radio Frequency 5 14 Mp3 on off a PD 13 14 CONTROL PANEL FOR STEAM SHOWER Power on off Steam temeprature setting Steam time setting Circulation Fan Chromatherapy Steam on off Music on off Radio Volume Freguency Radio memory adjustment adjustment A a NE re J lt D 12 Page Rev 10 2012 CONTROL PROCEDURES D bower on off Push any button to light the display and press the power on off switch to start the system Push the power on off switch again to turn off the system and display C l Steam Temperature Setting Touch the Steam Temperature Setting button and the display will appear on the screen The temperature ranges from 20 C to 59 C circularly Let go of the button when the desired temperature has been reached and the figure is set as a steam setting The steam generator stops working when the temperature inside is 4 C higher than setting temperature The steam generator has 4 C variance between accrual set temperature and real temperature The default steam setting is 45 C if the user does not choose any setting L Steam Time Setting Touch the Steam Time Setting button and the display The range is 20 59 minutes Let go of
9. lve is not shutting off Steam generator keeps adding water 2 Water level sensor cannot detect Clean scale of water level sensor or signal replace it 1 There is short circuit from heater Replace heater Power supply is off when on off button is pushed 2 There is short from thermal switch zni Replace thermal switch inside heater Water leaks from valve The seal is damaged Change the seal Water flow volume is low Water supply has clogged filter Clean Filter For additional help call Steam Planet Corp at 1 866 STEAM 61 16 Page Rev 10 2012 17 Page Rev 10 2012 oo STEAM PLANET 18 Page Rev 10 2012
10. oo STEAM PLANET Royal Care Series Installation amp Operations Manual WS 109 WS 115 Note You must read all installation amp operation instructions prior to assembly and use of this unit 1 Page Rev 10 2012 Table of Contents Notice to Installers Tools Needed for Installation Product Features Unit Information Electrical Information Plumbing Requirements General Information Installation Instructions for WS102 amp WS105 Installation Instructions for WS109 8 WS115 Cleaning amp Maintenance Steam Generator Cleaning General use amp Maintenance Control Parts Information LCD Display Information Control Panel Information Control Procedures Wireless FM Transmitter Information Troubleshooting Thank you for selecting Steam Planet Corp Computerized Steam Rooms In order to operate and use the product properly please follow all instructions provided in this User s Manual Our company reserves the right to change the Manual at anytime The manual takes effect the date it is published This manual shall prevail if there is any difference between this and previous documents and manuals 2 Page Rev 10 2012 NOTICE TO INSTALLERS if applicable THE FLEXIBLE DRAIN HOSE THAT IS INCLUDED WITH THIS UNIT IS FOR INSTALLATION INTO AN OPEN FLOOR DRAIN ONLY SUBSTITUTING THE EXISTING DRAIN SHOE FOR A DIFFERENT ONE WILL NOT VOID THE WARRANTY AS LONG AS THERE NO DAMAGE OR EVIDENCE OF MISUSE TO THE BASE IF A DIFF
11. rame using ST4X16 self tapping Screws Attach sc MA 154 8 Page Rev 10 2012 INSTALLATION INSTRUCTIONS FOR WS109 8 WS115 11 Install top on unit using ST4X12 self tapping screws 457 taimi e te 12 WS109 ONLY install clear fixed glass panel with holes for hinges to left side of unit using the ST4X20 self tapping screws that are already attached to the frame ome 13 WS109 ONLY Attach large clear glass panel to the side using the ST4X20 self tapping screws 14 WS109 ONLY Install hinges and door to the panel that was installed see image in 13 15 WS109 ONLY Install door gaskets and door handle m Fe 16 WS115 ONLY Install clear fixed glass panel to left side of unit using the ST4X20 self tapping screws that are already attached to the frame STJO e we 17 Attach the right side using the same process 18 WS115 ONLY Install the sliding door First put the upper wheels of the sliding door into the upper track Push down the lower wheels and get them into the lower track ee 19 Test all electrical and water on unit before final installation and sealing 20 Reinstall the aluminum trim pieces 21 Seal main panel with 100 silicone as shown below Do not use for 24 hours 9 Page Rev 10 2012 CLEANING AND MAINTENANCE FOR ALL UNITS 1 Liquid detergents and soft cloth should be used Do not use any abrasive cleaners 2 The scale on the surface can be cleaned with a so
12. reless transmitter for all devices v v v v Chromatherapy LED multiple Color Lighting v v v v Waterproof Oak Shower floor Grid v v v v Accessory Rack v v v v Circulation Fan v v v v Corner Unit v v v v Folding Seat v Removable Wood Stool v v v Sliding doors v Swinging Door v UNIT INFORMATION t ama ao Parameter _ Voltage Length Width Height WS102 220V 60 50Hz 1016mm 40 Inch 1016mm 40 Inch 2250mm 88 5 Inch WS105 220V 60 50Hz 1200mm 48 Inch 1200mm 48 Inch 2250mm 88 5 Inch WS109 220V 60 50Hz 1200mm 48 Inch 915mm 36 Inch 2250mm 88 5 Inch WS115 220V 60 50Hz 915mm 36 Inch 915mm 36 Inch 2250mm 88 5 Inch Steam Ready 1 2 minutes optimum room temperature reached within 2 5 MIN 4 Page Rev 10 2012 ELECTRICAL INFORMATION e 1 dedicated 12 2 wire with 20 amp GFCI breaker 220V e Connect the overhead light speaker fan CD telephone according to the tags on the wires e Do not connect the wire O3 to anything e Connect main power supply PLUMBING INFORMATION The unit is equipped with 3 ft hot and cold metal braided water supply hose with inch national pipe thread to connect from faucet manifold Manifold is located 4 ft high on rear of unit to the shutoff valves should be installed where they can be accessed Note base edge sets directly against back and sidewall Do not install any pipes along walls as to impede the base from setting flush against them e Install hot and cold shutoffs with 72 in
13. tom 18 Reinstall the aluminum strips near the back panel i k F hy i 1 1 19 Adjust the sliding doors so that they close tightly 20 Attach the door gaskets 21 Lastly place the wooden floor grids on the shower tray and place stools WS 105 only on the inside of the unit 22 Install the shower wand and flexible hose and place inside sliding shower rail 7 Page Rev 10 2012 INSTALLATION INSTRUCTIONS FOR WS109 amp WS115 1 Adjust the legs of the base Make sure the base is level and all the feet are supporting the unit Slide base out from wall to begin assembly of the unit 2 Connect the top horizontal rail to the two vertical side pieces using the ST4X50 self tapping screws on the left side and the ST4X40 on the right side 3 Attach assembly to base using the same screws on their respective sides 4 Attach ST4X12 self tapping screw to base with decorative cap 7 4 s we ores 5 Attach handheld shower bracket to main panel using nuts bolts and cap included in pack that the handheld shower bracket comes in Mes 6 Place large back panel with soap tray onto base and secure with ST5X25 screws 7 Install main panel with manifold and touchpad on axis pins 8 Pull out aluminum trim covers to expose assembly holes 9 Attach water supply and power 220v supply to main back panel Make sure all connections are tight 10 Connect back panel to f
Download Pdf Manuals
Related Search