APOPTZ-IR18 Manual - CCTV Ireland CCTV Ireland
Contents
1. POWER UP PARAMTER BACK EXIT e POWER UP It is to set the PTZ operation when the speed dome boots up The option includes NONE AUTO SCAN PRESET PATTERN TOUR and etc Please use the left right button to set e PARAMTER Here you can set the serial number of the corresponding operation such as the scan preset pattern tour Please use the left right button to set e BACK Go back to the previous menu e EXIT Log out the system menu 29 O Copyright Qvis amp All documentation rights reserved Menu Password Move the cursor to the MENU PASSWORD and the click the confirm button to go to the fourth menu PASSWORD PASSWORD 1 2345 SETTING 6 7890 BACK gt SAVE BACK EXIT e PASSWORD It is to set the speed dome menu password Please use the left right button to set e SETTING Click the confirm button to go to the password setup interface Please use the left right button to set the value and then click the confirm button to confirm current option Move the cursor to the SAVE button and then click the confirm button to save current setup Click the BACK button to go to the previous menu e BACK Go back to the previous menu e EXIT Log out the system menu If you have forgot your password After three times of login failure system may pop up an 8 digit internal code Please contact our technical engineer for help 4 5 Dome Troubleshooting 4 5 1 Restore to Factory Default Setup From main menu SYSTEM INFORMATION move cu2. 2 E 4 gt d If possible Accessories o e o o o o Note O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes 36 O Copyright Qvis amp All documentation rights reserved Note e This manual is for reference only Slight difference may be found in the user interface e All the designs and software here are subject to change without prior written notice e All trademarks and registered trademarks are the properties of their respective owners e If there is any uncertainty or controversy please refer to the final explanation of us e Please visit our website or contact your local service engineer for more information 37 O Copyright Qvis amp All documentation rights
3. acknowledgement or to its previous position before alarm 1 2 11 Auto Flip As long as you continue to hold the keyboard joystick in the down position the dome rotates 180 degrees and repositions itself for uninterrupted viewing of any subjects that passes directly beneath the dome 1 2 12 Self diagnosis There is a self diagnosis procedure when dome boots up e Tilt and vertical engine check e Camera diagnostics e Display dome information and diagnosis information such as address protocol baud rate type 1 2 13 Day Night Mode B W amp Color Mode Auto manual switches in low illumination e Auto camera will automatically adjust CCD light level e Manual use menu or function keys to select day night mode This function needs the speed dome driver camera supported 1 2 14 Auto Focus Auto focus allows the lens to remain in focus during zoom in zoom out and motion functions to get vivid image You can use FAR or NEAR button to adjust focus manually O Copyright Qvis amp All documentation rights reserved 1 2 15 Backlight Compensation Balance the brightest and darkest sections of a scene to produce a more vivid picture 1 2 16 Pan Tilt and Zoom e Supports zoom in and zoom out during tilt and pan movement e nthis period focus and iris are both in auto mode to get clear image 1 2 17 3D Intelligent Location Working with DVR just click part of the current scene will be displayed in the central window and automatically zooms A
4. amp All documentation rights reserved 4 4 2 Display Setting PRESET TITLE AZIMUTH DISP TIME DISP POSITION ZOOM DISP INSIDE TEMP TITLE DISP BACK EXIT Move the cursor to DISPLAY SETUP and then click confirm button you can go to the third submenu Please use the left right button on the keyboard or in the speed dome terminal menu to set After completed setup please click save button to save current setup PRESET TITLE Display dome preset title or not Please use the left right button on the keyboard or in the speed dome terminal menu to set You can go to Function Setup gt Preset section to set corresponding preset value and preset title AZIMUTH DISP Display dome current coordinates or not Please use the left right button on the keyboard or in the speed dome terminal menu to set TIME DISP Display dome system time or not Please use the left right button on the keyboard or in the speed dome terminal menu to set POSITION Display the angel between the benchmark and then current location Please use the left right button on the keyboard or in the speed dome terminal menu to set ZOOM DISP Display speed dome zoom speed or not Please use the left right button on the keyboard or in the speed dome terminal menu to set INSIDE TEMPERATURE Display dome internal temperature or not There are three options C F Off Please use the left right button on the keyboard or in the speed dome terminal menu to set TITLE DISPLAY Here y
5. reserved For more information about our DVRs and available cameras amp accessories please visit our website www adata co uk Alternatively scan this QR code with your smart phone to be directed instantly to our website ofto E m gl mm pr 38 O Copyright Qvis amp All documentation rights reserved
6. set the PTZ action when the speed dome boots up Click the confirm button to go to the next interface e MENU PASSWORD It is to set the password to go to the PTZ menu Click the confirm button to go to the next interface e MENU IDLE If current setup is ON once you open the menu and leave it idle for specified period the menu may automatically disappear If current setup is OFF the menu is always there and will not disappear Please use the left right button to set e PTZ AUTO STOP The speed dome will stop all the PTZ operations when there is no command for the specified time It includes various setups Please use the left right button to set e BACK Go back to the previous menu e EXIT Log out the system menu recy Mask Move the cursor to PRIVACY MASK and click confirm button system goes to privacy mask setup interface PRIVACY NO ACTIVATE RESIZE DELETE SAVE BACK EXIT 28 Copyright Qvis All documentation rights reserved Note For security reasons please set privacy zone a little bit larger than the privacy object size Each time after modifications you need to move the cursor to SAVE button and then click confirm button to get all setup activated Otherwise privacy zone may not move correspondingly with the object Please enter privacy mask menu now all the privacy zones are closed Move the cursor to PRIVACY NO please use left right key to set different privacy zones For example shift to 001 sectio
7. setup RESTART Reboot the speed dome BACK Go back to the previous menu EXIT Log out system menu 14 O Copyright Qvis amp All documentation rights reserved 4 4 1 1 Initialisation information ADDR BAUD RATE PARITY SOFTWARE BACK EXIT Move the cursor to INITIAL INFORMATION and then click confirm button you can see the above interface Here you can view dome basic information 4 4 1 2 Address Information ADDR TYPE HARD ADDR HARD 001 ADDR SOFT 001 BACK EXIT Move the cursor to SITE INFORMATION and then click confirm button e ADDR TYPE There are two options soft and hard Please use the left right button on the keyboard or in the speed dome terminal menu to set Please click the OK button to confirm e ADDR HARD Itis an address you set in the dial switch You cannot modify it through software ADDR SOFT You can set address via software It is to say you can use menu to modify dome address The value ranges from 1 to 255 BACK Go back to the previous menu EXIT Log out system menu 4 4 1 3 System Time Setting e Move the cursor to SYSTEM TIME SETING and then click confirm button you can go to the third submenu Please use the left right button on the keyboard or in the speed dome terminal menu to set After completed setup please click confirm button to save current setup After you see speed dome menu displays OK you can see the setup is valid now 15 O Copyright Qvis
8. 1 2 When there is an alarm from current channel system activates relay or not e Device default setup is NO NO Normal open alarm output For the default setup 1 channel alarm input and 2 channel alarm output is optional GND Alarm input ground end Alarm in 1 7 2 channel alarm input It is to receive relay signal from the external alarm source You can go to dome menu to activate specified preset or patter e When the activation mode is NO normal open dome alarms when there is low voltage High voltage will not activate the alarm e When the activation mode is NC normal close dome alarms when there is high voltage Low voltage will not activate the alarm 3l O Copyright Qvis amp All documentation rights reserved Note Dome alarm input message is ground mode e Dome alarm input signal are two modes normal open and normal close e For the default setup 2 channel alarm input and 7 channel alarm input is optional 32 Copyright Qvis All documentation rights reserved 5 1 System Layout 5 1 1 System Connection Please refer to Figure 5 1 for system connection information Initialisation Info Figure 5 1 AC24V Power In Output 5 1 2 Alarm Connection Please refer to Figure 5 2 for alarm connection information Alarm Controller Figure 5 2 33 O Copyright Qvis amp All documentation rights reserved 6 FAQ 1 1 D
9. 13 32 000 005 013 B DWELL Here is to set the dwell time Please use the left right button on the keyboard or in the speed dome terminal menu to set B SPEED Here you can set the speed value When you move the cursor to one cruise number you can use left right button to turn the page When you move the cursor to one cruise number please click confirm button to set the cruise Please use up down button to set preset number dwell time and speed Use the left right button to go to the next cruise Click confirm button you can exit the setup After you completed the setup move the cursor to back button to go to the previous interface e DELETE CRUISE This deletes a cruise Input cruise number in CRUISE NO and then move the cursor to DELETE cruise click confirm button to delete CALL Here is to activate cruise Input touring number in touring NO and highlight CALL click confirm button to activate touring e STOP Here is to terminate touring BACK Go back to previous menu e EXIT Log out system menu 24 O Copyright Qvis amp All documentation rights reserved 4 4 4 5 Pattern PATTERN NO 001 PROGRAM START PROGRAM STOP RUN STOP BACK EXIT Pattern function can memory PTZ operation and camera focus zoom in and zoom out From the start position dome begins auto movement repeatedly This series IP dome supports maximum 5 patterns and one pattern can max support 400 commands Move the cursor to PATTERN and cl
10. 3 18 Thu Figure 3 4 11 O Copyright Qvis amp All documentation rights reserved 4 Menu 4 1 Screen Menu Index Note ERR means current setup is invalid means there is submenu INITIAL INFORMATION SYSIEM ADDR INFORMATION INFORMATION LANGUAG ENGLISH FACTORY DEFAULT RESTART BACK DISPLAY SETTING CAMERA SETTING FUNCTION SETTING AUTO RUN NEXT PAGE BACK EXIT The above diagram illustrates the overall structure of the speed dome setup menu Note e ERR means current setup is invalid e Please make sure all the cable connections are right 12 O Copyright Qvis amp All documentation rights reserved 4 2 Self diagnosis System Information ADDR BAUD RATE PARITY PROTOCOL SOFTWARE V1 04 3 After installation please connect speed dome to power The system goes on a self diagnosis and then it pops up the above interface to show the system information If there is anything wrong during the self diagnosis system pops up error code The above interface disappears after speed dome received the first command or the display time lasts for 4 minutes e ADDR Here you can view dome address information For example 001 H 1 is the address number H is hard address mode S is software address mode Baud rate Dome communication baud rate Parity Communication parity bit format PROTOCOL System can auto recognize industrial protocol PELCOD PELCOP Software Dome software versio
11. E AUN M cR A ER tenente tenente tte teen teeth 12 8 Auto Pattern RR TT cceeecteeketet he tke tette tne tet teen esee teen etee seen esee te tee tetro teen te ene pee ee en eue ee eoe uoo 1 2 9 99 Privacy Masking soe Ue REUNIR ee TM M S 1 2 10 Action on Alarms esie teen EC UO Rs coco Agee m 1 2 11 Auto Flip A Eee TEL 1 2 12 Nc E Reese eee A rere rens 1 2 13 DayiNiglit Mode B W amp ColomfMode MM 998 TII 1 2 14 Auto FOCUS o o RR cinc O 1 2 15 Backlight COMPE mom 1 2 16 Pan Tilt and ZOO Mica o Ma Recenter 1 2 17 3D Intelligent Location emen ee Es 1 2 18 ldle Status i R 28 c r E 1 2 19 Image Stabilizer FlipEemmm 999 0 MM Mm 1 3 Specifications eMe AA A o o 1 34 Performanee S pelli GatiOns eeeeeeeen eene eterne trennen enn A E 13 2 Technical Specifications ussssn d ONE ee V ONE S 2 QUICK CONFIGURATION TODA lt lt lt o cocacola cano UNO caca nana cananea na cana cosa 0000 2 1 A EE o A is O Eoo oo aaa 2 2 OTorz Tz o p a Eon TEE Ebo RR aca 3 WEB OPERATIObLemmm AA MP reete ENS O Copyright Qvis amp AII documentation rights reserved iii 3 1 Network Connectio ma sesse A RON RN EET ssossosssossosssssososoos 9 3 2 NS i E OR 9 mn MENU ci ll noo IBI EL La ee 12 4 1 Screen Menu Index 99 Nee eene eren en etteot rone roter ot RETE Tenes cn ci iodo dioss soon
12. EXIT Move the cursor to SCAN button and then click confirm button SCAN NO Here is to set auto scan number Please use the left right button on the keyboard or in the speed dome terminal menu to set e SET LEFT LIMIT Here is to set camera left address Click confirm button to save current setup e SET RIGHT LIMIT Here is to set camera right address Click confirm button to save current setup e SCAN SPEED Please use the left right button on the keyboard or in the speed dome terminal menu to set e RUN Please input auto scan number first and then please move the cursor to RUN and click confirm button to activate auto scan function e STOP Here is to terminate auto scan function BACK Go back to previous menu EXIT Log out system menu 23 O Copyright Qvis amp All documentation rights reserved 4 4 4 4 Cruise Touring CRUISE NO 001 CRUISE SETTING DELETE CRUISE RUN STOP BACK EXIT Move the cursor to highlight CRUISE item and then click confirm button to go to set interface CRUISE NO Here is to set the tour number Please use the left right button on the keyboard or in the speed dome terminal menu to set CRUISE SETTING Move the cursor to cruise setting item and then click confirm button You can see the following interface Here you can add or remove the preset and set the corresponding dwell time and call speed NO PRESET DWELL SPEED 01 000 005 013 02 000 005 013 03 000 005 0
13. QIS ATI2OI2T Z 18lI2 IR High Definition Speed Dome User s Manual V1 0 07 2013 ENHANCE YOUR NVR WITH OUR WIDE RANGE OF QVIS IP CAMERAS OUR PRODUCTS ARE FULLY TESTED TO WORK TOGETHER DONT SETTLE FOR LESS ALL OUR PRODUCTS CARRY VIS LOGOS O Copyright Qvis amp All documentation rights reserved i Welcome Thank you for purchasing the APOPTZ 18IR HD PTZ Speed Dome This user s manual is designed to be a reference tool for the installation and operation of your system Here you can find information about the corresponding IP camera s features and functions as well as a detailed installation method Before installation and operation please read the following safeguards and warnings carefully A 9 O Copyright Qvis amp All documentation rights reserved ii Table of Contents 1 FEATURES AND FUNCTIONS EIIIIRET 7 SERRIII eese rsen eene ranae nnn uuuunnunaun 1 1 General Introduction cenae eo soso ns ETT ere eee e eee TET PEE ipae ees e aC UR tenes eeu 1 2 FA ES AA A A A trt PIC t Esser eser M NNI T enne ne ee 00 1 25 On Screeml gU NM eese NL sse nennen tenen neni nere tene e tenter nene teinte teen 1 2 2 Support multiple protocols ia eco Mun iE 1 2 3 Proportional Pan and Tilt emm RI o Moo LP Tue T 1 24 On screen Tips coco ns conc Mee eee c REDE jeg DBP TESCO DANG Call 99 9 E Besos E OAO Scan oee AA IEA EE A EL RE IA
14. aily Maintenance Please clean dome cover regularly to continue receiving clear images Handle the cover with care Use water to wash Don t use cloth to clean Use mild detergent to clean if there is too much dust Note Please take care not to touch plating surface with uncovered hands or any bare skin as this my transfer bodily perspiration upon it and may erode it Uncovered hands may cause nail scratches to the dome cover when handling This will result in blurred images and impaired visual monitoring using the device 1 2 Problems and Solutions SYMPTOM CAUSE SOLUTION 1 No self diagnosis Red LED is not on Check power is connected or no video signal Your power supplying does properly earthed when connect dome to power not apply to the power Or connection is too loose Power off or transformer problem Check power supply condition or check transformer Red LED light on the power board is on e Power supplying is low e Something wrong with power board Use multimeter to check dome load Please contact retailer to replace power board 2 No self diagnosis There is a noise Power supplying is inadequate Replace power supplying Mechanical malfunction Need electrical engineer help 3 Video signal loss occurs in high speed rotation Power supplying is not sufficient Replace power supplying 4 Video signal is not successive Circuit connection
15. c FOCUS LIMIT It is to set the camera focus limit Please use the left right button on the keyboard or in the speed dome terminal menu to set e FOCUS SENSITIVITY It is to set the camera focus sensitivity Please use the left right button on the keyboard or in the speed dome terminal menu to set e IRLIGHT FOCUS CORRECTION It is to set the camera IR light focus correction Please use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu e EXIT Log out system menu 4 4 3 6 Next Page Move the cursor to NEXT PAGE and then click confirm button you can go to the submenu APERTURE RESTRAIN DIGITAL ZOOM PICTURE FLIP FREEZE FUNC AF SENSITIVITY CAMERA FACTORY DEFAULT CAMERA RESTATRT BACK EXIT APERTURE RESTRAIN It can automatically control the aperture in the low illumination environments It can reduce the noise DIGITAL ZOOM You can use the left right button to enable disable the digital zoom function 20 O Copyright Qvis amp All documentation rights reserved PICTURE FLIP This function allows you to turn the image rotation 180 degrees There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set FREEZE FUNCTION This function allows the system from one preset to another preset without showing the video during the PTZ movement There are two options on off Please use the left right butto
16. ck confirm button to save current time setup For other setups you do not need to use this button BACK Go back to previous menu e EXIT Log out system menu 4 4 3 4 Picture Adjustment HUE SATURATION COLOR CONTROL GAMA CONTRAST HIGH LIGHT BACK EXIT HUE It is to set the video hue Please use the left right button on the keyboard or in the speed dome terminal menu to set SATURATION It it to set the video saturation Please use the left right button on the keyboard or in the speed dome terminal menu to set 19 O Copyright Qvis amp All documentation rights reserved COLOR CONTROL It is to set the video color control Please use the left right button on the keyboard or in the speed dome terminal menu to set e GAMA It is to set the video gama Please use the left right button on the keyboard or in the speed dome terminal menu to set CONTRAST It is to set the video contrast Please use the left right button on the keyboard or in the speed dome terminal menu to set e HIGHLIGHT It is to set the video high light Please use the left right button on the keyboard or in the speed dome terminal menu to set e BACK Go back to previous menu e EXIT Log out system menu 4 4 3 5 Focus Setup FOCUS MODE FOCUS LIMIT FOCUS SENSITIVITY IR LIGHT FOCUS CORRECTION BACK EXIT e FOCUS MODE It is to set the camera focus mode It includes several modes such as auto manual semiautomati
17. ctions e IDLE FUNCTION There are two modes ON OFF Please use left right key to set e IDLE TIME System idle period Please use the left right button on the keyboard or in the speed dome terminal menu to set e IDLE ACTION There are several functions you can select NONE PRESET SCAN TOURING PATTERN Please use the left right button on the keyboard or in the speed dome terminal menu to set e SN It is the serial number of the None preset scan tour pattern when the system is idle e SAVE Move the cursor to SAVE and click confirm button to save current setup e BACK Go back to previous menu e EXIT Log out system menu 4 4 4 7 Auto Run Schedule task TASK NO TIME TASK TASK SETTING TASK INFORMATION DELETE TASK BACK EXIT e TASK NO Here you can set task number Please use the left right button to set e TIME TASK The schedule task allows the speed dome to implement corresponding setup during the specified time There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set e TASK SETTING Here you can set task time operation operation SN and etc Please click the confirm button to go to the fourth menu to set e TASK INFORMATION Here you can view the corresponding task information Please click the confirm button to go to the fourth menu to set e DELETE TASK Please input the task number to be deleted in the TASK NO and then move the cursor to the curren
18. e 2 1 please select a device IP address and then double click it to open the login interface Or you can select an IP address and then click the Login button to go to the login interface See Figure 2 4 In Figure 2 4 you can view device IP address user name password and port Please modify the corresponding information to login Please note the port information here shall be identical with the port value you set in TCP port in Web Network interface Otherwise you cannot login to the device If you are using the device background upgrade port 3800 to login other setups all become invalid IP Address 192 168 1 10 User Name Password Port Cancel Figure 2 4 7 O Copyright Qvis amp All documentation rights reserved After you logged in the configuration tool main interface is shown as below See Figure 2 5 Sy Contig loot Wert ork Paramore rrroe Systen Informatica Syster Upgrade General Parameter I pHCF Enable men gt IP Address 192 168 1 10 Subnet Mack z55 255 255 0 Gateway 192 168 1 2 Mec Address 20 02109 00 74 94 Figure 2 5 O Copyright Qvis amp All documentation rights reserved 3 Web Operation This series product supports the Web access and management via PC Web includes several modules live view PTZ set alarm logout and etc IP camera factory default setup e P address 192 168 1 108 e User name admin e Password admin 3 1 Network Connectio
19. e the cursor to the item and then click the confirm button to set BACK Go back to previous menu EXIT Log out system menu 21 Copyright Qvis All documentation rights reserved 4 4 4 1 Preset Setup PRESET NO 001 TITLE PRESETOO1 SETTING CALL BACK Move the cursor to PRESET button and then click confirm button to go to set interface PRESET NO Please use left right key to modify preset number The different protocols support different preset values The PELCOD and PELCOP support 1 to 255 For the industrial protocol the value ranges from 1 to 80 TITLE Title text is the label used for you to identify the camera System will automatically name a title for the camera SETTING Please input preset number first and then select the monitor zone Please move the cursor to setting and click confirm button The system will pop up a message PRESET Here means preset number And the SETTING column pops up an OK Now you successfully added a preset Please note you need to enable display preset title function first Main menu gt display setting gt preset title Repeat the above procedures to set more presets Once you want to modify a preset you can input the preset number you want to modify and then follow the above steps to set the preset You can successfully modify a preset content CALL Here is to recall preset Move the cursor to PRESET NO and then input corresponding preset value Then move the cursor
20. evel menu FOCUS LIMIT It is to set the distance between the camera and the object It can prevent the focus distance is too small which may result in focusing on the enclosure At the same time you can change the distance to change the focus speed ZOOM SPEED The bigger the value the faster the speed Please use the left right button on the keyboard or in the speed dome terminal menu to set APERTURE It is to adjust the lens to achieve clear video Please use the left right button on the keyboard or in the speed dome terminal menu to set NEXT PAGE It includes the following options APERTURE RESTRAIN DIGITAL ZOOM PICTURE FLIP FREEZE FUNCTION AF SENSITIVITY CAMERA FACTORY DEFAULT SETUP CAMERA RESTART Please use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu EXIT Log out system menu 4 4 3 1 White Balance Setup WBMODE R GAIN B GAIN BACK EXIT Move the cursor to WHITE BALANCE MODE and then click confirm button you can go to the submenu WHITE BALANCE MODE Set white balance adjustment mode There are two modes auto manual Please use the left right button on the keyboard or in the speed dome terminal menu to set R GAIN Before you set R GAIN option please note the mode shall not be auto Please use the left right button on the keyboard or in the speed dome terminal menu to set B GAIN Before you set B GAIN option please note the mode shall not be a
21. gs Electrical safety All installation and operation here should conform to your local electrical safety codes We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair Transportation Security No heavy stress violent vibration or contact with water is allowed during transportation storage and installation Please use the original packing material or the material of the same quality when you ship it back to the manufacturer Installation Do not apply power to the product before completing installation Do not put object s on the product Environment This product should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc Please keep it away from environments that contain electromagnetic radiation or objects that produce it Please keep sound ventilation around the device at all times Do not allow the water and other liquid to penetrate into the device if casing has been compromised This series product complies with the IP66 standard specified in the Degrees of Protection Provided by Enclosure Please make sure the CCD CMOS component is away from the radiation of the laser beam device Otherwise it may result in CCD CMOS optical component damage Daily Maintenance Current series product has no power butt
22. ick confirm button e PATTERN NO Here is to set pattern number The value ranges from 1 to 5 Please click left right key to configure e PROGRAM START Here is to memorize pattern starting point An icon OK pops up in screen to prompt you system begins memory pattern e PROGRAM STOP Here is to set pattern stop point After all the movement move the cursor to PROGRAM STOP and then click confirm button Now you have set one pattern System pops up an icon OK to prompt you system has memories one pattern e RUN Here is to activate pattern Input pattern number move the cursor to RUN and click confirm button system begins running pattern e STOP Here is to stop current pattern Input pattern number move the cursor to STOP and click confirm button System stops current pattern BACK Go back to previous menu e EXIT Log out system menu Note e The dwell time between two orders should be less than one minute otherwise system will set to default value as one minute After click PROGRAM STOP do not click CALL button before icon e disappears completely e Any manual operation during the pattern procedure will terminate current dome pattern operation 25 O Copyright Qvis amp All documentation rights reserved 4 4 4 6 Idle Motion IDLE FUNC OFF IDLE TIME 010MIN IDLE ACTION PRESET SN SAVE BACK EXIT When there is no available command for specified time dome automatically goes on the previous set fun
23. ion which meets the customers needs for surveillance at HD level This product is also qualified with intelligent identification ability privacy masking settings alarm activation WDR and some other functions In addition one can transmit audio video and control data via internet in a safe way Thus the surveillance is free from the restriction caused by the changes of time and places to realize a real time surveillance With the built in high speed PTZ this product can operate as a quick and accurate fixed positioning surveillance which is also very convenient to use 1 2 Features This series speed dome has the following features 1 2 1 On Screen Menu e This series product menu supports multiple languages e Itis easy for you to view dome information and configure dome camera parameters 1 2 2 Support multiple protocols You can use various devices such as matrix control keyboard and DVR and protocols to operate speed dome 1 2 3 Proportional Pan and Tilt e This function keeps the image from moving too fast when there is a large amount of zoom e The quick installed high definition speed dome continually decreases or increases pan and tilt speeds in proportion to depth of zoom When zooms speed is increasing the camera moving speed becomes slow When zooms speed is decreasing the camera moving speed becomes fast 1 2 4 On screen Tips Here you can view e Dome title and system version Software and hardware e Dome system tempe
24. is too loose Connect tightly Video switch or power problem Need electrical engineer help 5 Video is not clear Focus is in manual mode Control manually Dome cover is dirty Wash dome cover 6 During camera switch there is a tilt movement in the monitor Camera power is not in the same Phase When several domes are connected to one transformer please connect the transformer output cable to the domes same side 34 Copyright Qvis All documentation rights reserved 7 Appendix Thunder Proof and Surge Protection This series speed dome adopts TVS lighting protection technology It can effectively prevent damages from various pulse signals below 1500W such as sudden lighting and surge While maintaining your local electrical safety code you still need to take necessary precaution measures when installing the speed dome in the outdoor environment e The distance between the signal transmission cable and high voltage device or high voltage cable shall be at least 50 meters Outdoor cable layout shall go under the penthouse if possible For vast land please use sealing steel tube under the land to implement cable layout and connects one point to the earth Open floor cable layout is forbidden e Incase of strong thunderstorms occurring or it is installed near high sensitive voltage such as near high voltage transformer substation you will need to install addi
25. ll of these allow you to trace precisely 1 2 18 Idle Status When there is no available order you can use the menu to set dome idle status after specified duration The idle status includes turn to specified preset or go to scan tour or pattern function 1 2 19 Image Stabilizer Flip e You can enable image stabilizer function and flip in the menu e When there is vibration this IS function can guarantee video stability and when flip you can view the video more clearly e This function needs speed dome driver camera supported O Copyright Qvis amp All documentation rights reserved 1 3 Specifications 1 3 1 Performance Specifications All digital design All data are in the connection board No data loss when power off occurs e Integrated design high stability e Quick installed high definition speed dome max support 255 AN presets Support 8 auto touring Each touring max has 32 presets Built in e Low and medium speed dome max support 80 presets Decode e 5auto scan e 5 auto pattern Each pattern can max support 400 commands and the interval shall be less than 60s e Built in direction indicator e Support max 24 privacy mask zones Depends on the camera type e 7 channel alarm input 2 channel alarm output e Fine stepper driver stable performance react quickly precisely positioning e Integrated design tight structure Built in PTZ Elegant mechanical driver device Support 360 degrees continuous
26. n Please follow the steps listed below for network connection e Make sure the IPC has connected to the network properly e IPC IP address and PC IP address shall be in the same network segment IPC default IP address is 192 168 1 108 If there is router please set the corresponding gateway and subnet mask e Use order ping IP camera address to check connection is OK or not 3 2 Login and Logout Open IE and input IP camera address in the address bar For example if your camera IP is 192 168 1 108 then please input http 192 168 1 108 in IE address bar See Figure 3 1 d Duk Page Windows iieiaei Toplisten v Mosen r Input your IP address here ow eere Figure 3 1 System pops up warning information to ask you whether install control webrec cab or not Please click OK button system can automatically install the control When system is upgrading it can overwrite the previous Web too If you can t download the ActiveX file please check whether you have installed the plug in to disable the control download Or you can lower the IE security level See Figure 3 2 9 O Copyright Qvis amp All documentation rights reserved Internet Options X Security Settings Internet Zone General Security Privacy Content Connections Programs Advanced meds s Settings O Disable Select a zone to view or change security settings O Enable e a y ee 9 Download signed ActiveX c
27. n and then move the cursor to ACTIVATE Secondly use left right key to select ON mode Now there is a privacy zone in the screen centre Thirdly use PTZ to move camera so that privacy object fit well with screen centre Fourthly move the cursor to RESIZE and then click left and right key to adjust privacy zone direction and D cuu M ae size 7 Fifthly move the cursor to SAVE and then click confirm button to exit PRIVACY NO Here is to set privacy mask zones Please use the left right button on the keyboard or in the speed dome terminal menu to set The value ranges from 1 to 24 Please note the value here may vary due to different protocols ACTIVATE There are two settings on and off When activate function is on the privacy mask function will be activated and displays in the screen When activate function is off the privacy mask function will be closed and the blank will not displayed in the screen RESIZE It is to adjust the privacy zone size Please continue pressing direction button to widen or narrow zone size is to narrow the horizontal width and is to widen the horizontal width is to widen vertical height and is to narrow the vertical height SAVE Here is to save user setup DELETE Here is to delete setup and restore default setting BACK Go back to previous menu EXIT Log out system menu Power Up Move the cursor to the POWER UP item and then click the confirm button you can go to the fourth menu
28. n of the control firmware When you are using the control keyboard or the matrix host to control the device please make sure the control parameter of the keyboard or the matrix host is the same with the speed dome OSD including address baud rate parity Please make sure the cable connection is OK 4 3 Main Menu You can open the IP dome menu via monitor platform web control keyboard matrix or speed dome control terminal SYSTEM INFORMATION DISPLAY SETTING CAMERA SETTING FUNCTION SETTING IR LIGHT SETTING EXIT e SYSTEM INFORMATION Dome self diagnosis information address information system time setup set north direction language factory default setup reboot and so on DISPLAY INFORMATION Display dome preset title azimuth display time direction dome internal temperature and etc information CAMERA PARAMETERS Display dome white balance setup camera function setup day night setup shutter setup and etc e FUNCTION SETTING Set preset pan scan auto cruise pattern idle motion time task and privacy mask function EXIT Log out the system menu 13 Copyright Qvis All documentation rights reserved 4 4 Menu Operation In the speed dome main menu you can use the left right button on the keyboard or in the speed dome terminal menu to configure the system menu Before setup please move the cursor to the current item you want to configure e In main menu please click confirm button to go to
29. n on the keyboard or in the speed dome terminal menu to set AF SENSITIVITY You can set the auto focus threshold value here CAMERA FACTORY DEFAULT SETTING Move the cursor to current item and then click confirm button to restore factory default setup CAMERA RESTART Move the cursor to current item and then click confirm button to reboot the camera BACK Go back to previous menu EXIT Log out system menu 4 4 4 Function Setting PRESET PAN AUTO SCAN AUTO CRUISE AUTO PATTERN IDLE MOTION TIME TASK NEXT PAGE BACK EXIT Please go back to main menu and move the cursor to FUNCTION SETTING click confirm button You can see the above interface PRESET Move the cursor to PRESET and then click confirm button to go to the third submenu PAN Move the cursor to PAN and then click confirm button to go to the third submenu AUTO SCAN Move the cursor to SCAN and then click confirm button to go to the third submenu AUTO CRUISE Move the cursor to AUTO CRUISE and then click confirm button to go to the third submenu AUTO PATTERN Move the cursor to PATTERN and then click confirm button to go to the third submenu IDLE MOTION Move the cursor to IDLE MOTION and then click confirm button to go to the third submenu TIME TASK Move the cursor to TIME TASK and then click confirm button to go to the third submenu NEXT PAGE It includes PRIVACY MASKING PTZ SPEED SET ZERO POWER UP MENU PASSWORD MENU IDEL PTZ AUTO STOP and HEATER Mov
30. on Please unplug all corresponding power cables before your begin installation or daily maintenance work Please keep the dustproof cap back to protect the CCD or CMOS part if the device does not work for a long time Do not touch CCD CMOS component You can use the blower to clean the dust on the surface of the device You can use the dry cloth with some alcohol or mild detergent to clear if necessary Do not use volatility solvent such as the benzene or thinner or detergent with strong abradability It may result in lens damage or it may adversely affect the device performance O Copyright Qvis amp All documentation rights reserved vi lf there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device 6 About Accessories Always use all the accessories recommended by manufacturer Before installation please open the package and check that all the components are included in the package Contact your local retailer ASAP if something is missing in your package O Copyright Qvis amp All documentation rights reserved vii 1 Features and Functions 1 1 General Introduction The six inch megapixel high speed smart network dome camera integrates the functions of network based remote surveillance and integrated high speed smart dome which makes it convenient to install and easy to use This product incorporates a megapixel level resolut
31. ontrols not secure us O Disable Internet Local intranet Trusted sites Y Enable not secure Se gt Prompt recommended Internet z 4 Download unsigned ActiveX controls not secure Q This zone is for Internet websites Disable recommended except those listed in trusted and Enable not secure restricted zones O Prompt Security level For this zone t DS i script epi controls not marked as safe For s Allowed levels For this zone Medium to High a Medium high O Prom Appropriate For most websites LJ Prompts before downloading potentially unsafe 9 Run ActiveX controls and plug ins content O Adminicteator annravad Unsigned ActiveX controls will not be downloaded lt ll Takes effect after you restart Internet Explorer Custom level Defar Reset custom settings Resetto Medium high default ims Figure 3 2 After installation the interface is shown as below See Figure 3 3 1 Please input your user name and password 2 Default factory name is admin and password is admin 3 Select the network connection type 4 The login type includes TCP UDP Multicast Note For security reasons please modify your password after you first login Figure 3 3 10 O Copyright Qvis amp All documentation rights reserved After you logged in you can see the main window See Figure 3 4 WEB SERVICE Fare lr il tamm tom Ao o Lj 2012 05 10 10 4
32. opyright Qvis amp All documentation rights reserved between the strong light and the dark light is too high Please use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu e EXIT Log out system menu 4 4 3 3 Day Night Setting Move the cursor to DAY NIGHT SETTING and then click confirm button you can go to the submenu DAY NIGHT AUTO DAY TIME 07H 00M NIGHT TIME 19H 00M THRESHOD E 4 SAVE BACK EXIT e DAY NIGHT Please use the left right button on the keyboard or in the speed dome terminal menu to set e DAY TIME Current setup becomes valid when day night mode is Time Move the cursor to DAY TIME item and then click confirm button to go to setup Please user up down button to set the value After completed setup please click confirm button to exit and move the cursor to Save button to save current setup NIGHT TIME Current setup becomes valid when day night mode is Time Move the cursor to DAY TIME item and then click confirm button to go to setup Please user up down button to set the value After completed setup please click confirm button to exit and move the cursor to save button to save current setup THRESHOLD The speed dome can switch the day night mode when it reached the threshold you set here e SAVE This button is for DAY TIME and NIGHT TIME setup After you set the day time or night time you need to move the cursor here and then cli
33. orresponding rafersaticn te lepia esis Figure 2 1 Select one IP address and then right click mouse you can see an interface is shown as in Figure 2 2 CEA O ab i3eledit Getesag Mae Address t 10 15 2 111 101504 90 T ab cS M 0 10 15 44 1015605 82 54 te fe MG 1 10 1 amp 0 1 WO we Te s in 1 amp 0 i 72 54 dy fa 1 54 10 15 6 1 9 05 vr 04 19 21 1 2001 90 300 90 02 49 04 72 21 00 a 02 04 1 10 15 5 198 10 15 6 WO ds 06 TY fa J 10 152 137 wiso 22 54 42 fa 41 Jo D 10 15 5 17 10150 WG We TE of it EMO O e tf feth fatit rrr te AS iz ABD 3002 WALT LADO 1344 64 ITT 600 20 02 wo 00 T2 fa 14 WO P 16 34 s De ue 06 T4 94 t i 5 Mo 60 f 6 rr CARD ROOT OEE OT LL 04 teo 0 40r f d 1 10 IE T 08 10 16 0 254 amp e O 5 19 188 1 17 ive 108 90 ec 04 07 1100 m i0 15 0 9 T 9 09 48 36 a 10 15 0 He Se 2 z C Dte La TE ttia 20 Daawa e fip Tou cn chick legin betten directly asi then iagat correspending inferestion to logta vet hogst Bete eth beta Legat Figure 2 2 6 O Copyright Qvis amp All documentation rights reserved Select the Open Device Web item you can go to the corresponding web login interface See Figure 2 3 Tipi x Figure 2 3 If you want to modify the device IP address without logging in the device web interface you can go to the configuration tool s main interface to set In the configuration tool search interface Figur
34. oss tt tn en cono conoci eR eroe eran seset NAN T 12 4 2 SelfidiagnosiS SUSTENTO AUN eam 13 4 3 AAA A A A RR RR 13 4 4 Menu Operation AA A A LO A A ON 14 4 441 SystemWnitermatiommie EPROP ceases ccecceeseccessstiMiter es seceesceesaesseeeeenecesenaeseacensaneessasensnedtseneeesensesscers 14 4142 DisplayZSetting E occ esse 16 4 4 8 Camera Setting ette een eteee tette O SES 16 4 4 4 Function Setting ee ETE A MMM cocceesteeesatieedeers 21 4 5 Dome TroubleshOOting AAA A A AN A 30 4 5 1 BRestoreitogEactory Default Setupigs 9998 899 BIBIT Leere ntn 30 4 5 2 SEP TZ Movements PoeWstmnpe OLh A circa 30 5 CABLE CONNEGTION ce eeeee eae eee eee eee AMI onde e eee 31 5 1 System La ayOUl e A A o NR e AS RO 33 5 1 1 System Connection oa 33 a Alarm Genrnection O a US 33 77 M E TA AR A 34 1 1 Daily Maintenance o o ommocomisnoisasssroccosonocncononocnc nono co tp ee reae ee ee e pues mos eate ee ene EE PE EE DE Ras 34 1 2 Problems and Solutions iee eee MM seen eter poten cerent tester eoee sensei Tar ree eee PITE TEES 34 7 APPENDIX THUNDER PROOF AND SURGE PROTECTION e eeeeeeeeennn 35 8 APPENDIX 2 TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS 36 O Copyright Qvis amp AII documentation rights reserved iv Important Safeguards and Warnin
35. ou can set to display speed dome position information and etc You can use the speed dome control terminal to set the detailed title information Please use the left right button to set BACK Go back to the previous menu EXIT Log out system menu 4 4 3 Camera Setting WB SETTING EXPOSURE SETTING DAY NIGHT SETTING FOCUS SETUP PICTURE ADJUST ZOOM SPEED APERTURE NEXT PAGE Move the cursor to CAMERA SETTING and then click confirm button you can go to the submenu WHITE BALANCE SETUP Move the cursor to current option and then click confirm button you can go to the third menu 16 O Copyright Qvis amp All documentation rights reserved EXPOSURE SETTING Move the cursor to current option and then click confirm button you can go to the third menu DAY NIGHT Set day night mode Move the cursor to current option and then click confirm button you can go to the third menu There are three options auto manual off Please use the left right button on the keyboard or in the speed dome terminal menu to set Please make sure your product supports this function FOCUS SETUP It is to set camera focus mode focus limit and etc Please use the left right button on the keyboard or in the speed dome terminal menu to set PICTURE ADJUSTMENT It is to set the camera hue saturation color control gamma contrast brightness There is the third menu Please move the light to highlight current item and then click the OK button to go to the next l
36. rature Optional You can disable this function e Dome pan tilt coordinates preset ID 1 2 5 Preset Setup and Call Preset function is to save the address information such as PTZ panrtilt focus etc to the memory so that you can quickly adjust the dome and PTZ to the correct position This series quick installed high definition speed dome supports 255 presets O Copyright Qvis amp All documentation rights reserved 1 2 6 Auto Scan Camera scans back and forth regularly in a horizontal field Here you need to set left and right limit and scan speed You can set 5 scanning paths 1 2 7 Auto Touring Add addresses into a routine and desired order and then set time and stop duration for each address The dome will begin an auto touring between these addresses Each touring path can contain max 32 presets 1 2 8 Auto Pattern Memorise dome operation such as pan tilt and zoom to repeat You can call it to repeat the previous operation 1 2 9 Privacy Masking Privacy masking is a user defined four sided area that cannot be viewed by you The masking area will move with pan and tilt functions and automatically adjust in size as the lens zooms 1 2 10 Action on Alarm System can connect 7 channel NO NC input and 2 channel NO alarm output via the socket connector Alarms can be individually programmed to initiated pattern or go to an associated preset scanning touring when received Dome will return to a previously programmed state after alarm
37. rotation no monitor blind spot e 0 17s rotation speed while maintain stable image e 180 degrees tilt continuous monitor Built in zoom lens high T e Auto focus e Auto BLC ds e Auto brightness control di al e Auto white balance uc e Auto day night switch Auto B W amp color switch color camera Preset title display View dome initial setup information Modify camera parameter Set preset OSD Set auto scan Set auto patter Set 2 channel alarm input and 1 channel alarm output Set auto day night switch Auto B W amp color switch Set privacy mask zones O Copyright Qvis amp All documentation rights reserved 1 3 2 Technical Specifications Power It depends on the product your purchase Camera Driver 12W Consumption Decoder Built in Engine Stepper motor Preset 255 PELCO D protocol 80 In industrial protocol Please note the value may vary due to different protocols Auto Tour 8 Auto Pattern 5 Auto Scan 5 Privacy Mask 8 zones in one window The different series products support different amount It depends on the camera type Alarm Input Output 7 channel alarm input and 2 channel alarm output Default setup is 2 channel alarm input and 1 channel output Information Time address dome title dome coordinates temperature alarm and etc Lens Adjust speed in accordance with lens Auto Rotation Tilt 92 a
38. rsor to FACTORY DEFAULT and click confirm button Dome will reboot and all the setups restore to factory default setup 4 5 2 PTZ Movement is not smooth From menu to SYSTEM INFORMATION move cursor to RESTART and click confirm button This reboot will not modify all activated setup such as preset tour and pattern 30 O Copyright Qvis amp All documentation rights reserved 5 Cable Connection Multiple function combination cable consists of network cable audio video port RS485 port alarm input output cable port Please refer to the label for detailed information 1 RS485 and audio video port power port and network port information is shown below Name Function A 485 A port It is to control the speed dome built in PTZ 485 B 485 A port It is to control the speed dome built in PTZ GND Ground end GND Ground VIDEO OUT Video output port You can connect this port if you want to use the analog video output Name Function POWER Power port Please refer to the label for detailed information EARTH Ground port LAN Network port Connect to the network cable Please refer to the label instruction for the alarm connection information of the multiple function combination cable You can connect 485 port if you want to use the RS485 to control the network speed dome Otherwise you do not need to connect 2 Relay in out interfaces is shown below Name Function Alarm out
39. t item Click the confirm button you can remove all the setups in the current schedule task Now current task is null e BACK Go back to the previous menu e EXIT Log out the system menu 26 O Copyright Qvis amp All documentation rights reserved Task Setting Move the cursor to the TASK SETTING and then click the confirm button you can set the task begin time end time action and etc WEEK 1 START TIME OFF END TIME RUN ACTION PRESET NO SAVE BACK EXIT e WEEK Here you can set the week information Please use the left right button to set You can set for one day or you can set for the whole week e START TIME Here you can set the task begin time Move the cursor to current item and then click confirm button to set the time Please use the up down button to set the detailed value and then use left right button to go to the next setup item After you completed the setup please click confirm button to exit start time setup and then move the cursor to the SAVE button to save current setup e END TIME Here you can set the task end time Move the cursor to current item and then click confirm button to set the time Please use the up down button to set the detail value and then use left right button to go to the next setup item After you completed the setup please click confirm button to exit end time setup and then move the cursor to the SAVE button to save current setup e TASK ACTION The option here includes none to
40. the sub menu or use left right key to configure setup Use up down button to select back option and then click confirm button to go back to the previous menu Use up down button to select exit option and then click confirm button to log out system menu All setup here will not lose when encounter power failure 4 4 1 System Information INITIAL INFORMATION ADDR INFORMATION SYSTEM TIME SETTING SET NORTH LANGUAGE ENGLISH FACTORY DEFAULT RESTART BACK EXIT INITIAL INFORMATION Move the cursor to INITIAL INFORMATION and then click confirm button to go to the third submenu ADDR INFORMATION Move the cursor to SITE INFORMATION and then click confirm button to go to the third submenu SYSTEM TIME SETTING Move the cursor to SYSTEM TIME SETTING and then click confirm button to go to the third submenu SET NORTH DIRECTION Set dome benchmark direction so that you can know the angel between the benchmark and then current location Please move the cursor to the option and then click confirm button until you see O K Now you have set north direction LANGUAGE The dome menu language There are several languages for you to select Please use the left right button on the keyboard or in the speed dome terminal menu to set FACTORY DEFAULT Restore dome factory default setup Please move the cursor to the option and then click confirm button until you see O K Now you can see the IP dome begin rebooting to restore factory default
41. tional high power thunder protection device or lightning rod e The thunder protection and earth of the outdoor device and cable shall be considered in the building whole thunder protection and conform to your local national or industry standard System shall adopt equal potential wiring The earth device shall meet anti jamming and at the same time conforms to your local electrical safety code The earth device shall not short circuit to N neutral line of high voltage power grid or mixed with other wires When connect the system to the earth alone the earth resistance shall not be more than 49 and earth cable cross sectional area shall below 25 mm2 See Figure 7 1 Video Lighting Rod Communication Lighting Rod Power R 1 Lighting Rod The speed dome shall be installed within the 45 angel of the lighting rod Earth cable resistance shall be less than 40 Steel tube shield Figure 7 1 33 O Copyright Qvis amp All documentation rights reserved 8 Appendix 2 Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Pb Hg Cd Cr VI PBB PBDE Sheet Metal O o o o o o Plastic Parts o o o o o o PCB o o o o o o Housing o o o o o o Camera Driver o o o o o o Bearing o o o o o Y Connection a A s d n Cable Motor o O O O oO O If possible Power O o O a O o If possible Bracket A
42. to CALL and then click confirm button to go to a preset BACK Go back to previous menu EXIT Log out system menu For PELCO protocol user please refer to the following special functions Call preset Call preset 28 or preset 95 to go to dome menu Call preset 29 or preset 99 to go to scan Call preset 24 or preset 81 to go to pattern Call preset 25 or preset 82 to go to cruise tour Call preset 30 or preset 96 to stop scan or pattern Call preset 31 or preset 83 to begin rotation Call preset 33 to enable PTZ 180 degrees rotation Call preset 34 to set dome position as O Set preset Set preset 26 or 92 to set scan left limit Set preset 27 or 93 to set scan right limit Set preset 22 or 79 to begin record Set preset 23 or 80 to stop record 22 O Copyright Qvis amp All documentation rights reserved 4 4 4 2 Pan PAN SPEED 160 RUN STOP BACK EXIT Move the cursor to PAN button and then click confirm button to go to setup interface PAN SPEED Set dome rotation speed Please use the left right button on the keyboard or in the speed dome terminal menu to set e RUN Move the cursor to call item and then click confirm button The dome begins 360 degrees continuous rotation e STOP Highlight stop item and then click confirm button The dome stops rotation BACK Go back to previous menu e EXIT Log out system menu 4 4 4 3 Scan SCAN NO 001 SET LEFT LIMIT SET RIGHT LIMIT SCAN SPEED 160 RUN STOP BACK
43. tton on the keyboard or in the speed dome terminal menu to set SLOW AE In the strong light environment you can lower the camera exposure speed to capture the image and enhance the definition Please use the left right button on the keyboard or in the speed dome terminal menu to set SLOW SHUTTER In lower illumination environment you can lower the cameras auto exposure time to capture the image and enhance the definition Please use the left right button on the keyboard or in the speed dome terminal menu to set NEXT PAGE It includes AUTO GAIN LIMIT AUTO SLOW SHUTTER LOW LIMIT NOISE CONTROL 3D NOISE REDUCTION BLC WDR BACK and EXIT Move the cursor to the item and then click the left right button to set o AUTO GAIN LIMIT Please click the left right button to set o SLOW SHUTTER LOW LIMIT Please click the left right button to set o NOISE REDUCTION There may noise when the camera is monitoring the low illumination environments You can use the digital filter to process the noise to guarantee the clear video o 3D NOISE REDUCTION o BLC Itis an abbreviation for back light compensation System can compensate the object in the dark light to achieve a clear video Please use the left right button on the keyboard or in the speed dome terminal menu to set o WDR EENBALE It is an abbreviation for wide dynamic region Please make sure your camera supports current function This function can adjust the video brightness when the contrast 18 O C
44. ur scan preset patter and etc Please use left right button to set e OPERATION NO It is the corresponding serial number of the schedule task The number here may vary due to different action types e BACK Go back to the previous menu e EXIT Log out the system menu Task Information Move the cursor to the TASK INFORMATION and then click the confirm button to go to the following interface Here you can see the corresponding task information Click the confirm button again you can exit current interface ACTION ALL 00 00 SCO001 ALL 00 00 SCO001 ALL 00 00 SCO001 ALL 00 00 SCO001 ALL 00 00 SCO001 ALL 00 00 SCO001 ALL 00 00 SCO001 27 Copyright Qvis All documentation rights reserved 4 4 4 8 Next Page Move the cursor to the NEXT PAGE and then click the confirm button you can go to the third menu to set the PTZ SPEED SET ZERO POWER UP etc PRIVACY MASK PTZ SPEED SET ZERO POWER UP MENU PASSWORD MENU IDLE PTZ AUTO STOP SAVE BACK EXIT e PRIVACY MASK Here you can set the privacy mask number etc It includes the third menu Please move the cursor to the current item and then click the confirm button to go to the next interface e PTZ SPEED It is to set PTZ speed Please use the left right button to set e SET ZERO lt is to set the PTZ initial position Please move the PTZ to the corresponding position and then click the confirm button to complete the setup e POWER UP It is to
45. uto Please use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu EXIT Log out system menu 17 O Copyright Qvis amp All documentation rights reserved 4 4 3 2 Exposure Setting AE MODE AGC GAIN LIMIT GAIN SETTING SLOW SHUTTER LIMIT SHUTTER NOISE REDUCTION IRIS SETTING 211 BLC EXPOSURE COMP WDR ENABLE SLOW AE 0 BACK SLOW SHUTTER EXIT NEXT PAGE BACK EXIT AE MODE Here you can set the camera exposure mode It includes auto manual AV iris priority TV shutter priority Please use the left right button on the keyboard or in the speed dome terminal menu to set o Auto It becomes valid after you set the exposure compensation backlight compensation BLC slow shutter wide dynamic region WDR o Manual It becomes valid after you set the gain setting shutter iris setting wide dynamic region WDR o AV It becomes valid after you set the exposure setting iris setting wide dynamic region WDR o TV It becomes valid after you set the shutter setting exposure compensation wide dynamic region WDR GAIN SETTING Please use the left right button on the keyboard or in the speed dome terminal menu to set SHUTTER Please use the left right button on the keyboard or in the speed dome terminal menu to set IRIS SETTING Please use the left right button on the keyboard or in the speed dome terminal menu to set EXPOSURE COM Please use the left right bu
46. uto rotates to pan 180 Auto Pan 0 360 continuously Manual Pan Motion 0 1 300 S Speed Preset Maximum 400 Speed Manual Tilt Motion 0 1 120 S Manual Tilt Scan 0 180 Section PTZ Scan Accuracy 0 06 0 015 Signal Format PAL NTSC Camera mode S N Ratio gt 50dB Humidity lt 90 Environment 40 G 60 C outdoor 3 O Copyright Qvis amp All documentation rights reserved 2 Quick Configuration Tool 2 1 Overview Quick configuration tool can search the current IP address or and modify IP address At the same time you can use it to upgrade the device Please note the tool only applies to the IP addresses in the same segment 2 2 Operation Double click the ConfigTools exe icon you can see an interface is shown as in Figure 2 1 In the device list interface you can view device IP address port number subnet mask default gateway MAC address and etc t s j d 10 15 5 44 10 155 10 15 82 10 15 2 4 mor 259 2000 1 2 1002 f X 3OUER ADE wA Taz Med 10 15 5 166 10 15 131 10 15 4 159 43 SOUS WEE ExT D gt EL a E004 CaM GOOD ARES X TIA E2272 azssc2dddase2E aio eran BRRERRAEREAEM Amm z2222 thigSASTTHTDARITDSDM 10 0 e EGI SEE HEE ROT VEA Max w x K x x x x x x w 0 SEESFSECEBSLESCEESetat 2213933839824 BRAALBRRA x n5 Tip Ten can chick logis batten directly and then ipat c
Download Pdf Manuals
Related Search