Defender Series Surge + PDU User Manual
Contents
1. Lock the SX DS L630 FP and SX DS SX 05 L630 FP SX D5 L530 FP SX DS IEC FP L530 FP plugs by turning to the right PAR figure 6 a o Do not plug the unit into a UPS or re locatable power tap UPS devices should only be connected to the surgeX Defender Series unit e Check Front Panel o Check the front panel to make sure the green Outlets On LED is lit e lf the green Outlets On LED is lit your Defender Series unit is ready to be used and is protecting your server and ancillary equipment figure 7 a o If the green Outlets On LED is not lit but the red Wiring Fault Indicator LED is lit a wiring fault at the outlet has been detected The SurgexX unit will not operate until the Wiring Fault is resolved by a qualified electrician Refer to the Front Panel LED Indicators section for further instructions figure 7 b IV Common Configurations e To properly protect your system connect all ancillary server equipment including UPS Battery Backup to the SurgeX Defender Series output power receptacles figure 8 a SERVERS amp ANCILLARY EQUIPMENT SERVERS amp ANCILLARY EQUIPMENT SurgexX REV A Page 4 SURGEX E e Defender Series Surge PDU User Manual V Front Panel LED Indicators e Power Indicator Green the green Power Indicator LED located on the left top of the front panel indicates that the electrical AC Mains is properly wired and power is available at the ou2. e Use 4 cage nuts to secure the 4 thumbscrews to the rack figure 3 b e Connect the Power Cables o Connect the ancillary server equipment power plugs to the IEC output power receptacles located on the rear panel of the Defender Series unit Distribute the equipment load evenly between the receptacle banks figure 4 a o To properly protect your system connect all ancillary server equipment including UPS Battery Backup to the SurgeX Defender Series output power receptacles Refer to Common Configurations section for reference o Check that the equipment you have connected to the Defender Series meets the following electrical rating requirements e SX DS L630 FP IMPORTANT ONLY CONNECT EQUIPMENT RATED FOR USE WITH NORTH AMERICAN 120 230VAC SPLIT PHASE e SX DS L530 FP IMPORTANT ONLY CONNECT EQUIPMENT RATED FOR USE WITH NORTH AMERICAN 120VAC SINGLE PHASE e SX DS 520 FP IMPORTANT ONLY CONNECT EQUIPMENT RATED FOR USE WITH NORTH AMERICAN 120VAC SINGLE PHASE e SX DS IEC FP IMPORTANT ONLY CONNECT EQUIPMENT RATED FOR USE WITH 220 240VAC SINGLE PHASE e Secure the Power Cables optional o Secure equipment power cords to the cable organizer if desired using cable ties or zip ties to prevent accidental removal figure 5 a SurgexX REV A Page 3 SURGEX maeray ine oe Defender Series Surge PDU User Manual e Plug in the Power Cord o Connect the input power cord of the 6 a SurgeX Defender Series to AC Mains
3. B 50kHz 50MHz gt 30dB 50kHz 50MHz gt 30dB 50kHz 50MHz gt 30dB 50kHz 50MHz Common Mode Common Mode Common Mode Common Mode gt 30dB 150kHz 50MHz gt 30dB 50kHz 50MHz gt 30dB 50kHz 50MHz gt 30dB 150kHz 50MHz Over Voltage 280 Volts 42 150 Volts 42 150 Volts 42 280 Volts 42 Shutdown Restores at 260 Volts 2 Restores at 135 Volts 2 Restores at 135 Volts 2 Restores at 260 Volts 2 100 msec Over Voltage 100 msec Over Voltage 100 msec Over Voltage 100 msec Over Voltage 17 44 W x 12 08 D x 1 71 H 17 44 W x 12 08 D x 1 71 H Koski A 17 44 W x 12 08 D x 1 71 H 1 RU 1 RU 1 RU H 1 RU E 12 5 Ib 12 5 Ib 12 5 Ib 12 5 Ib Rack Mounting mouded Included Included Included Hardware Standalone kcuded Included Included Included ae Power Indicator Indicator LED LED Green LED LED Green 0 LED LED Green LED LED Green 0 LED Red Illuminated when LED Red Illuminated when LED Red Illuminated when LED Red Illuminated when Wiring Fault no protective Earth Ground no protective Earth Ground no protective Earth Ground no protective Earth Ground Indicator present present or when Line Neutral present or when Line Neutral present reversed reversed 100 BTU h Maximum at full 100 BTU h Maximum at full 100 BTU h Maximum at full 140 BTU h Maximum at full BTU h rated load rated load rated load rated load Temperature Temperature Range 5 5cto40e to 5ct
4. SURGEX E e Defender Series Surge PDU User Manual Congratulations on your SurgeX purchase and thank you for your business Our Defender Series multi stage protection technology will increase server uptime by protecting your equipment from dangerous power events that can disrupt or even destroy your investment Your Defender Series Surge PDU unit provides i Failsafe protection Shields server equipment from damaging surges spikes over a voltage EMI RFI noise and wire faults that can cause downtime disruption and e equipment shutdown Power distribution A comprehensive Surge PDU all in one solution Redundancy Extended protection for UPS and ancillary equipment and creates a e stress free environment to keep your system up and running A D Uptime Helps increase uptime protect data extend equipment life and increase reliability of connected equipment Our goal is your complete satisfaction Please visit surgex com defenderseries for additional product information user manuals warranty information and product warranty registration Contact us at inquiries surgex com for direct assistance Thank you for your purchase SurgexX Product Description e Power Distribution Unit with multi stage Surge Protection e Models o SX DS L630 FP e 120 230 VAC Split Phase North American 24A Maximum Capacity 15A Maximum Capacity per Bank W 1 NEMA L6 30P 6 IEC 320 C13 output 6 2 15A Branch Rated input p
5. le Organizing Hardware Optional o Use 2 thumbscrews to attach the cable organizer to the rear panel figure 1 a e Configure Unit o Select Tower or Rack Mount Configuration e Determine which configuration is best for your installation o Option A For tower installations the Defender Series Surge PDU may be configured to mount upright as a Tower and can stand on any dry flat surface o Option B For rack installations the Defender Series Surge PDU may be configured to mount within a standard 19 equipment rack and will require 1 RU Rack Unit of space SurgexX REV A Page 2 SURGEX mmerayiatohic out Defender Series Surge PDU User Manual o To Install Tower Configuration Option A e Use a Phillips screwdriver and 6 6 32 x 7 flathead screws to attach the base stand figure 2 a e Place the Defender Series unit on a flat stable surface in an upright position resting on the base stand figure 2 b o To Install Rack Mount Configuration Option B e Use a Phillips screwdriver and 5 6 32 x 1 flathead screws to attach the left rack bracket figure 3 a e Use a Phillips screwdriver and 6 6 32 x 1 flathead screws to attach the right rack bracket figure 3 a e Insert the Defender Series unit into an available 1RU rack space from the front of the rack figure 3 b Product is designed for U Space mounting only e Use 4 thumbscrews to secure the left and right rack brackets to the rack rails figure 3 b
6. o40e C 5 5 Ct040C to 5 Ct040C C 5 psrcwo4rc to psrcwo4rc C 5 5Ct040C to 5Ct040C C T 5 to 95 R H Non 5 to 95 R H Non 5 to 95 R H Non 5 to 95 R H Non Humidity Range i condensing condensing condensing condensing TUV Certified to UL 60950 1 TUV Certified to UL 60950 1 TUV Certified to UL 60950 1 CE CB Check surgex com Check surgex com Check surgex com Check surgex com Agency Listings defenderseries for country defenderseries for country defenderseries for country defenderseries for country specific certifications specific certifications specific certifications specific certifications Specifications subject to change without notice All listed specifications obtained at an ambient temperature of 25 SurgeX REV A Page 6
7. ower cord power receptacles e Circuit Breakers o SX DS L530 FP e 120 VAC Single Phase North American 24A Maximum Capacity 15A Maximum Capacity per Bank T 1 NEMA L5 30P input 6 IEC 320 C13 output 6 2 15A Branch Rated power cord power receptacles e Circuit Breakers o SX DS 520 FP e 120V Single Phases North America 20A Maximum Capacity 10A Maximum Capacity per Bank 1 NEMA 5 20P input 6 IEC 320 C13 output 6 2 15A Branch Rated power cord power receptacles e Circuit Breakers REV A Page 1 SURGEX aerar i Defender Series Surge PDU User Manual o SX DS IEC FP e 220 240 VAC Single Phase International 32A Maximum Capacity 10A Maximum Capacity per Bank 1 IEC 60309 332P65 input 6 IEC 320 C13 output N 3 10A Branch Rated power cord power receptacles MZ Circuit Breakers ll Hardware Included e Tower Configuration Hardware Option A 1 Base stand 6 6 32 x 2 Flathead Screws e Rack Mount Configuration Hardware Option B 1 Left 1 Right 11 6 32 x 1 bracket ag bracket Flathead Screws 4 Thumbscrews 4 Cage Nuts e Cable Organizing Hardware optional 1 Cable Organizer 6A 2 Thumbscrews 8 Plastic Ties III Installation Warning Before installing the SurgeX Defender Series unit review the safety instructions that came with the unit Unpack the Unit and Accessories o Identify each item refer to the Quick Start Guide for reference e Connect Cab
8. tput power receptacles figure 9 a e Wiring Fault Indicator Red the red Wiring Fault Indicator LED located to the right below the green Power Indicator LED on the front panel indicates that the electrical AC Mains is not properly grounded and power is not available at the output power receptacles figure 9 b o If the red Wiring Fault indicator LED is illuminated contact a licensed electrician to inspect the electrical AC source outlet and repair as necessary o S X DS L530 FP model only The red Wiring Fault Indicator LED may also indicate that the electrical AC Mains is improperly wired with the Line and Neutral conductors reversed and power is not available at the output power receptacles f IMPORTANT The presence of a safety Ground is essential to reduce the risk of electric shock If the red Wiring Fault indicator LED is illuminated contact a licensed electrician to inspect the AC power source outlet and repair as necessary Vi Over Voltage Conditions e Inthe event of a long duration over voltage condition the unit will stop passing power to connected equipment until the voltage returns to a safe operating level this function is designed to protect your system Vil Other Information You May Need Warning See the safety and regulatory information that is shipped with your Defender Series unit Warranty information may be included within this document or as a separate document o The User Manual provides information abo
9. ut product features and describes how to install and troubleshoot the unit this document is available online at surgex com defenderseries o The Quick Start guide that is shipped with your Defender Series unit describes how to install your system this document is available online at surgex com defenderseries o The Safety Guide that is shipped with your Defender Series unit describes all safety and regulatory information this document is available online at surgex com defenderseries o Note Always check for updated materials at surgex com defenderseries and read through these updated materials first because it may supersede information in other documents e Service Kits for replacement mounting hardware can be obtained by ordering Part SX DS SK MH Vill Technical Assistance e lf you do not understand these instructions or if the unit does not perform as expected visit surgex com defenderseries or email inquires surgex com for further assistance SurgexX REV A Page 5 SURGEX BE ace Defender Series Surge PDU User Manual IX Specifications 120 Volts 120 Volts Single Phase Phase 120 Volts 120 Volts Single Phase Phase 220 240 Volts 220 240 Volts Single Phase Phase Voltage Protection 800V Line Line 800V Line Line Rating VPR 500V Line Ground aye A ENORGS DAER 500V Line Ground Power Requirement 8 Watts 8 Watts 8 Watts 8 Watts no load Normal Mode Normal Mode Normal Mode Normal Mode Anena ation gt 30d
Download Pdf Manuals
Related Search