US-800 Owner`s Manual - 3.33 MB
Contents
1. s TEAC PROFESSIONAL US 800 USB 2 0 Audio MIDI Interface OWNER S MANUAL IMPORTANT SAFETY INFORMATION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT CAUTION REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE RISK COO NOT OPEN REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance FORU S A WARNING TO PREVENT FIRE TO THE USER OR SHOCK HAZARD DO NOT This equipment has been tested and found to EXPOSE THIS comply with the limits for a Class B digital device APPLIANCE TO RAIN OR pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against MOISTURE harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful Declaration of Conformity interference to radio communications However Model Number US 800 there is no guarantee that inte2. this device for sound input and ase this device for sound output This moves microphone icon and speaker icon to 15 298 Built in Microphone 05 800 W 20 Clock source SPDIF Clock Built in Line Input 2in A Built in Output 15 800 A Configure device Configure speakers Use this device for sound input 9 Use this device for sound output KC Play alerts and sound effects through this device Configure Speakers 3 Launch iTunes select an audio file and start playback Overview When this unit is not connected to a computer by a USB cable and the unit s power is ON the included TASCAM PS P520 AC adaptor is connected the unit will operate in stand alone mode In this mode you can use this unit as a microphone preamp without using a computer Settings for stand alone mode In stand alone mode input signals pass through the digital mixer which is set to fixed values and then the output selectors before being output from the output jacks Mixer The mixer settings are fixed at the following values Faders All set at 0 dB Pan Odd channels are set to the left channel and even channels are set to the right Mute All OFF Solo All OFF Stereo link OFF Output selectors Output selector settings are fixed at the following values LINE OUT 1 2 PHONES MIXER DIGITAL OUT 3 4 Sample rate When the digi
3. RICE nn Pb Hg Cd Cr VD PBDE 1 5515 HE O O O O O O 2 PCB x O O O O O 3 O O O O O 4 x O O 5 SEALBH s O O 6 O O O O O O ESTABA HWA AAA REA EE SJ T11363 2006 PAER O RR Xi RIVA Aa OB AA ADELA SJ T11363 2006 RARE MOR o CELE SCE AREF YAR PE AY A TASCAM US 800 3 1 Introduction e D Main 5 Product parts ssa 5 Manual conventions 6 Trademarks eene 6 Cautions on installation 6 Beware of condensation 6 Cleaning the 6 2 Names and Functions of Parts 7 Front panel tinte 7 Rear panel aio 8 Installation 10 System requirements 10 10 OS A escenario 10 Installing the driver and control panel10 Installing the driver and control panel for 11 Installing the control panel for OS um 12 Uninstalling the driver 12 Frequently asked installation questions and answers FAQ 13 Improving computer performance 13 Cubase LE 5 installation 13 4 US 800 control panel settings 14 A etit teinte 14 Control panel menus an
4. 18 TASCAM US 800 On Windows use the pull down menu to select the value On Mac click the corresponding button Settings 44100 default setting 48000 88200 96000 Hz When Clock CLOCE SOURCE Is set to pisital DIGITAL gt the sampling frequency is automatically set Solo SOLO MODE Set the Solo mode to Mix or Exclusive On Windows change this by clicking the button On Mac click the button for the desired setting e MIX default value Multiple tracks can be soloed together EXCLUSIVE Only one channel or one stereo pair of channels can be soloed at a time If this mode is in use when a new channel is soloed Solo will be turned OFF for any currently soloed channel Panel Ver Mac only This shows the version of the control panel software On Windows this is shown on the OUTPUT tab screen F W Ver Mac only This shows the firmware version of the device NOTE On Windows this is shown on the OUTPUT tab screen Output tab COMPUTER 1 2 COMPUTER 3 4 COMPUTER 5 6 DIGITALIN 7 8 mixer COMPUTER 1 2 COMPUTER 3 4 COMPUTER 5 6 DIGITAL IN 7 8 INT 44100 control panel Click the GUTPUT OUTPUT tab to open the corresponding window where you can make output settings Fader section Use these three pairs of faders to set the US 800 output You can EHE GUT PHO
5. 7 and Windows Media Player 1 Close all applications and then open the Tontral from the Start menu 2 Open Scund If the above item does not appear click Hardware and Sound and it should appear Sound 3 Click the Fi ssback tab click Speakers US 888 and click the Set Default button This moves the green check mark to Sr e akerz USS88 Audio TASCAM US 800 27 Playback Recording Sounds Select a playback device below to modify its settings Speakers Intel r 82801DB DBM 97 Audio Controller Working Speakers 5800 Audio Working Set Default a Properties Lec emen 4 Click bk 5 Start Windows Media Player select an audio file and begin playback If you change this setting while Windows Media Player is running the software will not recognize that the device has been changed In this case restart Windows Media Player If you still cannot hear sound after making the setting and completing the procedures above restart the computer After making this setting sound will be output through this unit but no sound will be output by the computer s speakers or headphone jacks 28 TASCAM 05 800 Mac OS X iTunes 1 Openthe iitiiities folder which is inside the fee licaticns folder and double click Audio HIDI Setur to launch it 2 Control click the iz 288 Check
6. Destination Folder C Program Files TASCAM US800 6 When the following screen appears click the 1 button 05800 Audio Driver Setup will now prepare your system for installation of device During this process the system may prompt you to confirm installation of software that has not passed Windows Logo testing Please select Continue Anyway to confirm installation Click Next to continue 7 When the following screen appears connect the unit with the computer using the included USB cable and then plug the included AC adaptor TASCAM PS P520 into the unit TASCAM US 800 11 1 STANDBY ON indicator USB indicator 00525555550 MM Information Confirm that the unit s 1 STANDBY ON and USB indicators have lit and then click the button 8 When Windows recognizes the US 800 driver installation starts automatically Driver installation Setup is now installing drivers This may take a few minutes 9 After installation completes the icon shown below appears in the notification area the system tray Click this icon to open the US 800 control panel 10 If the versions appear in the Ei Uer and F W Wer fields the STATE section of the GUTFUT screen installation has been successful DL ET gm TASCAM US 800 Installing the control panel for Ma
7. This unit has one quarter inch 6 3 mm stereo standard jack and one eighth inch 3 5 mm stereo mini jack Use the one suitable for your headphones You can also use both at the same time When doing so the combined output from both jacks is 49 mW 49 mW Connecting MIDI devices You can connect keyboards synthesizers drum machines and other MIDI devices to the MIDI input You can also for example connect sound modules to the MIDI output You can also use the MIDI IN and MIDI OUT connectors to send and receive MTC MIDI timecode By doing this you can synchronize a multitrack recorder that is compatible with MTC and MIDI devices using the computer application 24 TASCAM US 800 6 Using the mixer for low latency monitoring In this chapter we explain how to create low latency mixes for monitoring including how to use the various settings and specific examples Uses By using this unit s digital mixer for monitoring inputs can be monitored with very little delay For example this is useful when a performer wants to monitor the output of a guitar that is connected to an input on this unit Ordinarily sending the signal from the unit to the computer by USB through an application on the computer and then back to the unit by USB again takes approximately 20 ms or longer In this case the performer does not hear the sound of the guitar until approximately 20 ms or longer have passed making it very difficu
8. also joins the pan sliders into a single balance slider ON lit OFF default value unlit Fader level displays The current level of each fader is shown in decibels In the Mac version if you move a PAN slider the pan position L15 C R15 is shown momentarily instead gi Master fader section Windows Mac Master fader The stereo master faders include a fader for both left and right channels If the stereo link is disabled moving these faders separately is possible Mute M buttons Use these to mute channels ON lit OFF default value unlit TASCAM US 800 17 LINK button Use this stereo link button to synchronize the operation of the left and right master faders ON default value lit OFF unlit Fader level display The current level of each fader is shown in decibels System settings section v1 01 Windows Mac Clock CLOCK SOURCE Use this to set the Sample Clock source On Windows change the setting by clicking the button On Mac click the button for the desired setting Internal default value US 800 uses its internal clock Digital DIGITAL Clock signal received through DIGITAL IN connector used Lock DIGITAL LOCK indicator This shows whether the clock is in sync or not It lights when in sync Samplerate SAMPLE RATE Use to set the sampling frequency When Clack CLOCK SOURCE is set to Internal CIMTERHRL gt it can also be used to set it
9. convertor Sampling frequency 44 1 48 88 2 96 kHz Quantization bit rate 24 bit Inputs Analog inputs Microphone inputs MIC IN 1 6 Balanced Connectors XLR 3 31 1 GND 2 HOT 3 COLD Input impedance 2 2 Nominal input level 14 dBu 0 15 Vrms Minimum input level 58 dBu 0 001 Vrms Maximum input level 2 dBu 0 98 Vrms Line inputs LINE IN 3 6 Balanced Connectors 6 3 mm 1 4 TRS phone jacks Tip HOT Ring COLD Sleeve GND Input impedance 15 Nominal input level 4 dBu 1 23 Vrms Minimum input level 40 dBu 0 008 Vrms Maximum input level 20 dBu 7 75 Vrms Instrument inputs INST IN 1 2 Unbalanced Connectors 6 3 mm 1 4 TS phone jacks Tip HOT Sleeve GND Input impedance 1 MO Nominal input level 13 dBV 0 22 Vrms Minimum input level 57 dBV 0 001 Vrms Maximum input level 3 dBV 1 41 Vrms 34 TASCAM US 800 Digital input Coaxial DIGITAL IN Connector RCA pin jack Format IEC 60958 3 S PDIF Outputs Analog outputs Line outputs LINE OUT L R Unbalanced Connectors RCA pin jacks Output impedance 2000 Nominal output level 10 dBV 0 316 Vrms Maximum output level 6 dBV 2 Vrms Headphones outputs PHONES 1 2 Connectors 3 5 mm 1 8 stereo mini phone jack 6 3 mm 1 4 stereo phone jack Maximum output 49 mW 49 mW 1 kHz 0 1 320 Digital output Coaxial DIGITAL OUT Connector RCA pin jack Format IEC 60958 3 S PDIF
10. manual on the included Cubase LE 5 DVD ROM The sound breaks up or there is noise The processing load on the computer can cause sound to break up and noise to occur Some ways to reduce the load on a computer are introduced below 1 Ifa wireless LAN antivirus software or other software are running in the 32 TASCAM US 800 background they regularly use the computer s CPU and this burden can cause sound to break up and noise to occur Stop wireless LAN transmission antivirus software and other software running in the background when using this unit 2 Try increasing the buffer size latency setting in the audio application that you are using and or in the control panel for this unit Consult the maker of your audio application for methods to reduce its burden on your computer 3 Change the settings of your computer so that they are optimal for audio processing Windows XP 1 Right click fis Computer and select Properties 2 Click the Aduariced tab 3 Click Settings the Perfornance section 4 Onthe Ferformance screen select the Adjust for Best Performance option Windows Vista a Turn Aero off 1 Right click the desktop and select Personalize 2 Choose iiindoaw Color and feeearance and then click rer classic aPPearancerrorertissz for more options 3 Select Hindows Vista Basic option other than Hindows Bero
11. to the right R15 this is reversed When pan is set to center C the signal is sent equally to both left and right channels with a 3 dB reduction on both sides When Stereo link is ON sliders set the balance between left and right channels as the left becomes louder the right becomes quieter and vice versa One slider is Shown for both linked channels Input level meters These show the input levels of each channel For input 1 8 signals the pre fader levels are shown For computer 1 6 signals the post fader levels are shown Input faders Use these faders to adjust the mixer input levels in a range from ee to 6 dB In the following explanations the Windows version of the software is described first When the Mac version has a significant difference it is described second Mac version part names are indicated in parentheses SOLO S buttons When a 5 L 0 button is turned ON only channels with 301 0 buttons turned ON have their signal sent to the stereo bus All other channels are muted When the SOLO mode is set to SOLO can be turned ON for multiple channels If set to Exclusive only the last channel that was set to SOLO can be heard ON lit OFF default value unlit Mute M buttons Use these to mute channels ON lit OFF default value unlit L LINK buttons Use these stereo link buttons to synchronize the operation of the left and right channel faders in a pair This
12. 1 2 1 i i I SNOW 1 1 i 1 asn 1 ZH 1 LSNI OIIN pav 1 7 gt 1 2 1 LSNU OIW O 1 LI I 1 smejs apow uajs s i 1 1 LI 1 1 i Zt ISNUOIW 1 1 g 87070X 1 ee weber Moy 008 SN TASCAM US 800 37 38 TASCAM 05 800 TASCAM US 800 39 TASCAM TEAC PROFESSIONAL US 800 TEAC CORPORATION Phone 81 42 356 9143 1 47 Ochiai Tama shi Tokyo 206 8530 Japan www tascam jp TEAC AMERICA INC www tascam com Phone 1 323 726 0303 7733 Telegraph Road Montebello California 90640 USA TEAC CANADA LTD www tascam com Phone 1905 890 8008 Facsimile 1905 890 9888 5939 Wallace Street Mississauga Ontario L4Z 1Z8 Canada TEAC MEXICO S A de www teacmexico net Phone 52 55 5010 6000 R o Churubusco 364 Colonia Del Carmen Delegaci n Coyoac n CP 04100 M xico DF M xico TEAC UK LIMITED www tascam co uk Phone 44 8451 302511 Suites 19 amp 20 Building 6 Croxley Green Business Park Hatters Lane Watford Hertfordshire WD18 8TE U K TEAC EUROPE GmbH www tascam de Phone 49 611 71580 Bahnstrasse 12 65205 Wiesbaden Erbenheim Germany Printed in China
13. Control I O MIDI input MIDI IN Connector 5 PIN DIN Format standard MIDI format MIDI output MIDI OUT Connector 5 PIN DIN Format standard MIDI format USB USB Connector 4 pin USB type B Format USB 2 0 HIGH SPEED 480 MHz Audio performance Frequency response 20 Hz 20 kHz 0 5 1 5 dB 44 1 48 kHz JEITA 20 Hz 40 kHz 0 5 1 5 dB 88 2 96 kHz JEITA Signal to noise ratio 98 dB or higher LINE IN to LINE OUT with Gain knobs at minimum 44 1 kHz JEITA Total harmonic distortion 0 007 or less LINE IN to LINE OUT with Gain knobs at minimum JEITA Computer requirements See the TASCAM website for updated information about OS compatibility Windows Supported Operating system Windows XP 32 bit SP2 or later Windows XP 64 bit SP2 or later Windows Vista 32 bit SP2 or later Windows Vista 64 bit SP2 or later Windows 7 32 bit Windows 7 64 bit Supported computer system Windows compatible computer with a USB port USB 2 0 is recommended CPU clock Pentium 4 1 4 GHz or faster AMD Athlon 1 4 GHz or faster or equivalent processor Memory 1 GB or more Macintosh Supported operating system Mac OS X 10 6 3 or later Supported computer system Apple Macintosh series equipped with a USB port as standard equipment CPU clock Intel processor Memory 1 GB or more General Power TASCAM PS P520 AC adaptor included AC input 100 240 V 1 0A DC output 5 V 2 0 A Power consump
14. NES OUT and DIGITAL QUT settings LINE OUT COMPUTER 1 2 COMPUTER 3 4 COMPUTER 5 6 O DIGITAL IN 7 8 mixer wj Windows Mac Output name display The names of the faders are shown TASCAM US 800 19 OUTPUT selectors You can set the LINE OUT PHONES and DIGITAL outputs to the following options Setting Description Computer1 2 Signals 1 2 from the computer Computer3 4 Signals 3 4 from the computer Computer5 6 Signals 5 6 from the computer Digital In Signal from the DIGITAL IN connector Mixer default value Output signals from the internal mixer Level meters These show the levels immediately after the faders Faders Use these to adjust the output levels in a range from ee 0 dB Mute M buttons Use to mute individual channels ON lit OFF default value unlit L LINK buttons Turn these stereo link buttons ON to synchronize the operation of left and right channel fader pairs ON default value lit OFF unlit Fader level display The current level of each fader is shown in decibels 20 TASCAM US 800 Direct section Windows only Direct By using Direct I O in the US 800 driver audio signals can be exchanged between applications that use different interfaces Using this function the following types of operations are possible Record the playback sound of a multimedia player into a DAW that u
15. PHONES and MONITOR knobs on the front panel to the minimum volume before changing the PHANTOM 48V switch between ON and OFF Depending on the connected microphone loud noises might be produced and damage could be caused to equipment and harm could occur to people s hearing Always set the PHANTOM 48V switch to OFF before turning the unit s power on or off connecting or disconnecting the AC adaptor Guitars When connecting guitars and bass guitars to this unit directly use the MIC INST IN 1 2 1 4 jacks on the front panel Connecting keyboards drum machines sound modules cassette MD CD players and other analog line level devices Connect the analog signal outputs of these types of equipment to the MIC LINE INPUT 3 6 jacks standard TRS on the rear panel Connecting sound modules MD CD players and other digital devices Connect the external device s digital output to the IN connector on the rear panel of this unit To send this unit s signal to another device connect the US 800 s DIGITAL OUT to the other device s digital input The digital input and output connectors of this unit are RCA pin jacks TASCAM US 800 23 This unit can handle S PDIF digital input and output signals Monitor speakers Connect monitor speakers powered speakers or an amplifier and speakers to the LINE OUT jacks on the rear panel Headphones Connect headphones to the standard stereo PHONES jacks on the front panel
16. Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time Y df SE SEMIS AR IE n USC E 14 Refer all servicing to qualified service personnel Servicin
17. a e CD ROM containing drivers e DVD ROM Cubase LE5 Cubase LE5 Quick Start Guide e Warr nty Owner s Manual this document TASCAM US 800 5 1 Introduction Manual conventions Keys jacks and other parts on the unit and external dvices are indiated like this PHONES When we show messages for example that appear on the screen we show them like this Additional information is introduced in the styles below when needed LOAD TIP These are tips about how to use the unit These provide additional explanations and describe special cases CAUTION Failure to follow these instructions could result in injury damage to equipment or lost recording data for examaple Trademarks TASCAM is a trademark of TEAC Corporation registered in the U S and other countries Microsoft Windows Windows Vista Windows 7 and Windows Media Player are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Apple Macintosh Mac Mac OS X and iTunes are trademarks of Apple Inc Pentium and Intel are trademarks of Intel Corporation in the U S and other countries AMD Athlon is a trademark of Advanced Micro Devices Inc Cubase is a registered trademark of Steinberg Media Technologies GmbH ASIO is a trademark of Steinberg Media T
18. b Performance settings 1 Right click and select Proper Lies 2 Click Advanced system settings 3 Click the Advanced tab 4 Click Settings in the Performance section 5 Onthe Performance rtion screen select the Adjust for Best Performance option Windows 7 a Turn Aero off 1 Right click the desktop and select Personaliza 2 Select any theme from among Eas i and High Contrast Themes b Performance settings 1 Right click and select Properties 2 Click Advanced Sustem Settings 4 Click Settings in the Fer formance section 5 Effects tab inthe Performance Ort an window select Just for bes 1 Open Sssten Preferences from the Apple menu and select Eneraz Saver 2 Clickthe zizzr tab Set Fut the computer to sleer when itis inactive for to Hever 4 Set Put thedisrFlastz tosleer uhenthecomrulerizinactius fori to Never 5 Clickthe Geticrns tab Ifa Processorrerformance setting is available set it to Highest Depending on the Mac OS version and model these settings might not be available Questions related to Cubase LE 5 Since Cubase LE 5 is a product provided by Steinberg Media Technologies GmbH it is not supported by TASCAM Please use the Cubase LE 5 Help menu for information about how to use this software TASCAM US 800 33 F AD DA audio
19. c OS X This unit uses the class 2 0 compliant USB driver provided by Apple Inc so installation 12 TASCAM US 800 of only the control panel is necessary when using a Mac 1 Confirm that the unit is not connected to the computer Double click the 15 288 Panel arF on the included driver CD ROM A disk image named iz z amp amp Panel should appear on the computer Depending on the Finder Preferences settings it will appear on the desktop or in a Finder window Sidebar If it does not appear in either of these places select Ccmeuter from the menu of the Finder Click on this image to open it US 800 Panel Copy the 5 888 program icon to the computer desktop the Applications folder or another location of your choice US 800 Panel In the Finder close the 115 28 panel disc image folder Restart the computer and connect the unit with the computer to use it Uninstalling the driver Windows 1 Open the Control Panel from the St art menu and double click i Remove programs Select iizz88 Audio driver from the list and click the Change or Removes Programs button 3 Follow the instructions on the screen to complete the uninstallation m Windows Vista and Windows 7 1 Openthe CantrolPanesi from the 5t art menu and double click the ProgsramsandFeatures icon 2 Select iiz 288 Audio driver from the l
20. d settings 14 Menu bar 14 MIXER and OUTPUT tabs 415 Mixer tab screen 16 A 19 5 Connections 22 USB 5 23 Audio connections ees 23 Microphones sissies 23 Uc 23 Connecting keyboards drum machines sound modules cassette MD CD players and other analog line level devices 23 Connecting sound modules MD CD players and other digital ae a Monitor speakers 4 TASCAM US 800 Headphones s Connecting MIDI devices e 6 Using the mixer for low latency monitoring 25 25 Using the digital mixer for sica 25 7 Application guide 27 Cubase 5 derriere ec 27 Windows XP and Windows Media 27 Windows Vista or Windows 7 and Windows Media Player 27 Mac OS X and lt 28 8 Stand alone mode 29 A 29 Settings for stand alone mode 29 cle Output selectors Sample 9 MIDI implementation chart 30 10 Troubleshooting 31 11 Specifications 34 AD DA audio 34 Inputs 34 Analog inputs 34 Di
21. dows Window Minimize Select to minimize the control panel window Zoom This has no effect with this software Bring All to Front Select to bring all the control panel software windows to the front MIXER and OUTPUT tabs Click this to switch between the HIER tab and the GUTFLT tab In Windows OS the selected tab appears to be in front In Mac OS the selected tab button appears lit TASCAM US 800 15 Mixer tab screen 44100 Hz Solo MIC INST1 2 MIC UNE3 4 MIC UNE 5 6 us EE ges gums 9 ee ES E EN w w wj wj Caca GSE GEC Geo Geom Gece 10 SRA Mac control panel Click the HINER tab to open the HIKER Input fader pair screen where you can make internal mixer MIC INST 1 2 settings The 14 faders on the left are the 9 9 input faders In order from the left they are MM 6 channels of analog inputs 2 channels of o o digital inputs and 6 channels of signals from Y the computer The 2 faders on the far right are the left and right stereo master faders i ER w wj Windows Mac Input fader display The name of each input fader is shown 16 TASCAM US 800 Pan sliders Set the pan for each channel in a range of L15 C R15 When set all the way to the left L15 the input signal is sent entirely to the left channel 0 dB and no signal is input to the right channel When set all the way
22. e channel meters on the 1 should move when you do so 4 Click tab 5 When the output tab screen opens in the FHOHES area of the three output sections on the left set the output source selector to ti This sends the mixer output to the headphones output jacks Set this way the mixed sound of the computer application playing back and the MIC INST 1 input signal is sent to the headphones TASCAM US 800 25 TASCAM US 800 Mac control panel OUTPUT tab 6 Adjustthe headphones output volume using the fader in the P HOHES area of the output screen and the PHONES knob on the front panel of the unit 7 Usethe faders on the mixer screen to adjust the balance between the guitar and application playback sounds 8 To place the guitar sound in the center set the Mic Inst 1 pan to center C 9 If you want to eliminate all sound from the unused channels set their Hute buttons to ON or set the z i 0 buttons for MiceInst 1 and Comeuter 1 2 to ON solo mode must also be set to i x The above procedures are only an example You could also use other input jacks and use Computer 3 4 instead of Computer 1 2 for the playback sound You can even use all the mixer channels at once When using numerous channels be sure to adjust their faders to avoid clipping noise in the mix 26 TASCAM US 800 In this chapter we explain how to s
23. e output from a computer using the US 800 control panel Connect this jack to a recorder or external effect processors for example In stand alone mode the signals from MIC LINE INPUTS 3 4 are output from this jacks This unit is capable of output through its DIGITAL OUT jack at 24 bit 96 kHz USB port Use the included USB cable to connect this unit to a USB 2 0 compatible computer 47 DCIN 5V connector Connect the included TASCAM PS P520 AC adaptor which meets the specifications of this unit here Use only the included PS P520 AC adaptor which conforms to the specifications of this unit Use of an adaptor other than this model could cause malfunction fire or electric shock TASCAM US 800 9 System requirements See the TASCAM website http www tascam com for updated information about OS compatibility Windows Supported operating systems Windows XP 32 bit SP2 or later Windows XP 64 bit SP2 or later Windows Vista 32 bit SP2 or later Windows Vista 64 bit SP2 or later Windows 7 32 bit Windows 7 64 bit Supported computer systems Windows compatible computer with a USB 2 0 port CPU clock speed Pentium 4 1 4 GHz or faster AMD Athlon 1 4 GHz or faster or equivalent processor Memory 1 GB or more Although this product has been checked for use with typical computers that meet the above operating requirements we cannot guarantee that it will operate with all computers that meet th
24. e system settings section on the mixer tab screen About latency This unit s driver momentarily stores audio input and output signals in a buffer The size of the buffer can be adjusted The smaller the buffer is the shorter the delay is when monitoring the input audio signal Smaller buffers however require more computer processing at high speed If other system processes for example prevent the audio processing from being completed in time clicking and popping noises dropouts and other issues could occur with the audio signal On the other hand the larger the buffer size the more stable operation becomes making interference from other system processes less likely to affect the audio signal However the delay when monitoring the audio signal also becomes longer With this unit you can adjust the buffer size according to the capability of your system and your audio needs TASCAM US 800 21 Headphones Guitar p Bass guitar LLP Keyboard 2 8 5555 Digital recorder Powered speakers or amplifier and speakers Example of using US 800 connections 22 TASCAM US 800 USB connections Use the includ
25. echnologies GmbH Other company names product names and logos in this document are the trademarks 6 TASCAM US 800 or registered trademarks of their respective owners Cautions on installation Theunit s nominal operating temperature is between 5 and 35 C 41 95 Do not install in the following types of places Doing so could degrade the sound quality and or cause malfunctions Places with significant vibrations or that are otherwise unstable Near windows or other places exposed to direct sunlight Near heaters or other extremely hot places Extremely cold places Places with bad ventilation or high humidity Make sure that the unit is mounted in a level position for correct operation Do not place any object on the unit for heat dissipation Avoid installing this unit on top of any heat generating electrical device such as a power amplifier Beware of condensation If the unit is moved from a cold to a warm place or used after a sudden temperature change there is a danger of condensation vapor in the air could condense on the internal mechanism making correct operation impossible To prevent this or if this occurs let the unit sit for one or two hours at the new room temperature before using Cleaning the unit To clean the unit wipe gently with a soft dry cloth Do not use any benzene paint thinner ethyl alcohol or other chemical agents to clean the unit as they could da
26. ed USB cable to connect the US 800 to your computer as shown in the illustration Some USB devices access the USB bus frequently To avoid dropouts and clicks in the audio signal we strongly recommend that you do not connect any USB devices other than keyboards and mice to the USB bus used by this unit Audio connections Connect the analog outputs of microphones guitars keyboards and other audio devices to this unit which will convert their signals into digital signals and send them via USB to your computer Connect the outputs of the unit to speakers with amplification and headphones to monitor a mix of the audio signals being input into the unit and output from the computer You can adjust the level pan and other settings for each signal For details see 6 Using the mixer for low latency monitoring on page 25 Microphones Connect microphones to the MIC INST IN 1 2 XLR jacks on the front panel or the MIC LINE INPUTS 3 6 XLR jacks on the rear panel If you are using a condenser mic that requires phantom power set the PHANTOM 48V switch on the rear panel to ON Connecting a dynamic microphone with an unbalanced connection to the unit when the PHANTOM 48V switch is ON could damage this unit and make it unusable 5 Connections Do not connect or disconnect a mic with an input when this switch is ON Loud noises might be produced and damage could be caused to equipment Always turn the
27. eous use of ASIO and WDM audio protocols Two PHONES jacks a stereo phone jack and a stereo mini phone jack with a combined output of 49 mW 49 mW both output the same signal Input monitoring mixer uses digital processing to mix up to 14 ins and 2 outs One MIDI IN connector and one MIDI OUT connector Stand alone mode allows use of inputs and outputs without being connected to a computer by USB In this mode input signals are output from the output jacks according to the default settings of the mixer and the output selections This allows the mic preamps to be used without a computer Dedicated drivers for both Windows Windows XP Windows Vista Windows 7 and Mac OS 10 6 Mac USB Audio Class 2 0 compliant USB2 0 High speed 480 MHz Cubase LE 5 software included A note about computer operation If you are unsure about how to perform basic computer operations appearing in this manual please refer to the owner s manual that came with your computer Product parts The US 800 package contains the following items Take care when opening the package not to damage the items Keep the package materials for transportation in the future Please contact the store where you purchased this unit if any of these items are missing or have been damaged during transportation SE Ier e adaptor TASCAM 5 520 e Power cord for a USB CADIS riad
28. ese requirements Please be aware that even in the same conditions computer processing capabilities can vary depending on differences in design and specifications 10 TASCAM US 800 MacOS X Supported operating systems Mac OS X 10 6 3 or later Supported computer systems Apple Macintosh equipped with a USB port CPU Any Mac with an Intel processor Memory 1 GB or more Installing the driver and control panel In order to use this unit you must install the driver on to your computer As described below this is an easy process using the CD ROM included with the unit Drivers are updated from time to time You can download the most recent version of the driver from the TASCAM website http www tascam com Disconnect the unit from the computer before starting driver installation Handle the enclosed CD ROM with care If the disc becomes scratched or dirty a computer might not be able to read it making installation of the software impossible If the included disc becomes unreadable it can be replaced for a fee Never attempt to play the enclosed CD ROM in an ordinary audio CD player as the resulting noise could damage the speakers or harm your hearing Installing the driver and control panel for Windows During driver installation a warning that this software has not passed Windows Logo testing will appear This message appears when installing a driver that has not received Windows Log
29. et up some audio applications for use with this unit Cubase LE 5 For details see the included Cubase LE 5 Quick Start Guide Windows XP and Windows Media Player 1 Close all applications and then open the ControlPanel from the Start menu n 2 Open Sounds and Audio Devices Ifyou do not see the above item click Sounds Speech and Audio Devices and it should appear 9 Sounds and Audio Devices 3 Click the fiucic tab and set the Default devices for Sound Flayback to USSaa Sounds and Audio Devices Properties dbi Volume Sounds Audo Voice Hardware Sound playback O Default device I Sound recording Default device US800 MIDI music playback Default device Microsoft GS Wavetable SW Synth J Use only default devices 4 Click k 5 Start Windows Media Player select an audio file and begin playback Ifyou change this setting while Windows Media Player is running the software will not recognize that the device has been changed In this case restart Windows Media Player If you still cannot hear sound after making the setting and completing the procedures above restart the computer After making this setting sound will be output through this unit but no sound will be output by the computer s speakers or headphone jacks Windows Vista or Windows
30. forms to 1 60958 3 S PDIF specifications Thi sunit is capable of input through its DIGITAL IN jack at 24 bit 96 kHz 8 TASCAM US 800 45 2 3 FN MIDI IN connector This 5 PIN DIN is a standard MIDI input connector for inputting MIDI signals MIDI OUT connector This 5 PIN DIN is a standard MIDI output connector for outputting MIDI signals PHANTOM 48V switch Use this to turn 48V phantom power on for mic input connectors 1 6 Always set the PHANTOM 48V switch to OFF before turning the unit s power on or off connecting or disconnecting the AC adaptor Always turn the PHONES and MONITOR knobs to the minimum volume before changing the switch between ON and OFF Depending on the connected microphone loud noises might be produced and damage could be caused to equipment and people s hearing Do not connect or disconnect a mic with an input when this switch is ON Turn this switch ON only when connecting a condenser microphone that requires phantom power Do not supply phantom power to an unbalanced dynamic microphone Some ribbon mics can be damaged by phantom power If unsure do not supply phantom power to a ribbon mic 45 DIGITAL OUT connector coaxial This coaxial digital output jack conforms to IEC60958 3 S PDIF specifications This jack can output signals from a computer connected by USB or the output of the internal monitoring mixer for example Set which signals to b
31. g is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Do not expose this apparatus to drips or splashes Do not place any objects filled with liquids such as vases on the apparatus Do not install this apparatus in a confined space such as a book case or similar unit The apparatus draws nominal non operating power from the AC outlet with its POWER or STANDBY ON switch not in the ON position The apparatus should be located close enough to the AC outlet so that you can easily grasp the power cord plug at any time The mains plug is used as the disconnect device the disconnect device shall remain read ily operable If the product uses batteries including a battery pack or installed batteries they should not be exposed to sunshine fire or excessive heat CAUTION for products that use replaceable lithium batteries there is danger of explosion if a battery is replaced with an incorrect type of battery Replace only with the same or equiva lent type Caution should be taken when using earphones or headphones with the product because excessive sound pressure volume from earphones or headphones can cause hearing loss US 800 ABA EW RICK ES
32. gital 34 34 Analog outputs 34 Digital OutpUt assim 34 Control l O 34 Audio performance Computer requirements 35 WIN dOWS caidas 35 5 35 crc 35 Dimensional drawing 36 Block diagram s 37 Thank you for your purchase of the TASCAM US 800 USB 2 0 Audio MIDI Interface Before connecting and using the unit please take time to read this manual thoroughly to ensure you understand how to properly set up and connect the unit as well as the operation of its many useful and convenient functions After you have finished reading this manual please keep it in a safe place for future reference You can also download the Owner s Manual from the TASCAM web site http www tascam com Please also check the above site for the latest manual updates Main features Audio interface with 8 inputs and 6 outputs Supports audio formats up to 24 bit 96 kHz 2 XLR TS combo jack inputs balanced mic unbalanced instrument 4 XLR TRS combo jack inputs balanced mic line S PDIF digital input 48V phantom power can be supplied to 6 microphone inputs 2 unbalanced line outputs digital output and 2 headphone outputs S PDIF digital output Internal digital mixer for direct monitoring of input signals with little delay Supports multiple clients allowing simultan
33. he buffer size if the computer has insufficient processing power and noise occurs Increasing the buffer size however also increases latency audio signal delay Set this value to best suit your system Samplerate Sets the sampling frequency used Settings 44100 default value 48000 88200 96000 Hz Clock Set whether the unit uses its internal clock or a digital clock signal input through its DIGITAL IN connector Settings Internal default value Digital In Factory Default Use this to restore the software to its factory default settings Click OK when the confirmation screen appears Always on Top Set this to make the control panel always appear in front of other windows A check mark appears before this item when selected Help About Select to open a pop up window that shows the version of the US 800 control panel software MacOS US 800 Panel About US 800 Panel Select to show the version of the US 800 control panel software Hide US 800 Panel Select to hide the US 800 control panel Hide Others Select to hide software other than the US 800 control panel Show All Select to show all running software Quit US 800 Panel Select to quit the US 800 control panel software Configuration Restore Factory Defaults Use to restore the software to its factory default settings Always on Top Select to make the control panel always appear in front of other win
34. ist and click the 1i inzt311 button 3 Follow the instructions on the screen to complete uninstallation g MacOSX Move the US 800 Panel application icon to the Trash Frequently asked installation questions and answers FAQ Windows driver installation When connect the unit to a computer the Windows Hardware Wizard appears and cannot install the driver Am making a mistake during the installation procedures A Close the Windows Hardware Wizard and disconnect the unit You must install the driver before connecting this unit See Installing the driver and control panel for Windows on page 11 for the correct procedures the installation CD ROM into a Windows computer but the driver installation menu does not appear How can access this menu A The driver CD ROM does not launch automatically Follow the procedures in Installing the driver and control panel for Windows on page 11 to install the driver Improving computer performance In this manual we will offer only the following basic tip to improve performance when using this unit Do not run other applications Processing digital audio places a considerable load on your computer You probably use the computer for applications other than audio but we recommend that you avoid running them when using audio programs This means that if you are running other applications especially ones that are graphics intensive or that u
35. jacks Windows XP 1 Shut down all applications and open the CantrolFPanel from the Stari Menu 2 Open Sounds and Audio Devices If do not see the above item click Sounds Speech and Audio Devices and it should appear 3 Click the Audis tab and set the hDefaultdeuicei for zaound Flasback and Zzaundrecardina to TASCAM 05 588 TASCAM US 800 31 Windows Vista and Windows 7 1 Shut down all applications and open the ControlPanel from art menu 2 Open Scund If the above item does not appear click Hardware and Sound and it should appear 3 Click the Fi tab right click Sreakers 5 and click the Set Default button Mac OS X 1 Shut down all applications and open 5gstemPreferences from the Apple menu 2 Open zaund 3 From fiuteut tab select iiz 2 Dutrutl After completing the settings restart the computer and check the playback sound Depending on the application you are using other device settings might also be necessary in addition to those above In particular since DAW Digital Audio Workstation software operates using audio engines that are different from OS settings confirm the DAW driver settings first after installing the driver for this unit Check the manuals for the software that you are using for details about how to make these settings For the bundled Cubase LE 5 software see the
36. lt to play This unit has a digital mixer that can be used to avoid this situation Using this mixer you can mix the input signals with playback signals from the computer and output them from the unit The input signals sent to the mixer do not get sent over USB allowing them to be mixed and output with very little latency As a result the delay until the performer hears the sound of the instrument is reduced to an insignificant amount Moreover the digital mixer includes faders pan sliders mute and solo buttons as well as level meters allowing you to tailor the monitoring mix as desired Using the digital mixer for monitoring In this example a guitar is playing along with a backing track output from a computer application The sound of the guitar is mixed with the playback sound of the backing track from the application and the mix is output to headphones for monitoring The guitar is connected to the MIC INST 1 jack and headphones are connected to one of this unit s PHONES jacks 1 Open the unit s control panel and click the ii R tab to open the iii rp ER DEI Se TASCAM US 800 lem caca caca Mac control panel MIXER tab 2 Play the guitar and confirm that the HICA IHST 1 meter moves 3 Output the sound of the computer application to 15 38 1 72 monitoring Th
37. mage the surface 2 Names and Functions of Parts Front panel E t B t EE 5 ey o 0 D O STANDBY ON indicator 6 PHONES jacks knob Lights when the power is on Use the stereo mini jack PHONES 1 48 indicator and stereo standard jack PHONES 2 Lights when the PHANTOM 48V to connect stereo headphones The switch is set to ON maximum combined output for the stereo mini jack and the stereo standard CAUTION jack is 49 mW 49 mW Do not connect or disconnect microphones abis PHONES knob to adjust the when this indicator is lit 3 USB indicator CAUTION Lights when a USB connection is active Turn the PHONES knob to the minimum volume 4 OL and SIG indicators before connecting headphones Failure to do so OL overload indicators could cause sudden loud noises and damage Light just before an input is about to hearing for example distort when 2 dBFS is exceeded MONITOR knob SIG signal indicators Adjusts the LINE OUT L R output level Light when a signal is being input on Gain knobs the channel 30 dBFS or higher Use to adjust the input levels of MIC INST IN 1 2 and MIC LINE IN 3 6 separately Turn all the way to the left for the minimum level and turn all the way to the right for the maximum level 5 MIC INST IN jacks balanced unbalanced Use these combo jacks to connect both balanced and unbalanced a
38. nalog microphones and instruments with XLR connectors and standard quarter inch plugs Use the XLR connector for microphones balanced and the standard jack unbalanced for electric guitars basses and other instruments XLR 1 GND 2 HOT 3 COLD TS Tip HOT Sleeve GND TASCAM US 800 7 2 Names and Functions of Parts Rear panel 40 47 14 our PHANTOM 48V Dc IN sv Ses 8 9 Ki MIC LINE INPUTS connectors balanced Use these combo jacks to connect balanced analog microphones and line level inputs Use the XLR connector for microphones balanced and the standard jack balanced for keyboards samplers and other line level devices XLR 1 GND 2 HOT 3 COLD TRS Tip HOT Ring COLD Sleeve GND LINE OUT jacks unbalanced 1 2 or L R Use these RCA jacks for analog line output unbalanced These jacks can output signals from a computer connected by USB or the output of the internal monitoring mixer for example Set which signals to be output from a computer using the US 800 control panel Connect these jacks to a recorder powered speakers or external effect processors for example In stand alone mode the signals input by MIC INST IN 1 2 are output from these jacks DIGITAL IN connector coaxial This coaxial digital input jack con
39. o testing This message appears because the drivers for TASCAM products have not undergone Windows Logo testing We have however confirmed their proper operation If this message appears click Continue or Install to proceed with the installation Installation on a Windows computer 1 Confirm that the unit and the PC are not connected by a USB cable 2 Insert the included driver installation CD ROM into the PC where you will install it 3 Open the included driver CD ROM and launch the setup exe file inside US 800 Win Driver folder 4 When the following screen appears click the H2 t button 05800 Audio Driver Setup Welcome to 05800 Audio Driver Setup program This program wil install 05800 Audio Driver on your computer Before you continue please disconnect your USB audio device s from this computer system Itis strongly recommended that you exit all Windows programs before runring this Setup program Click Cancel to quit Setup and close any programs you have running Click Nest to continue with the Setup program 5 The Windows installation location screen appears Select where to install the driver and click the 1 button US800 Audio Driver Setup Setup will install 15800 Audio Driver in the following folder Toinstallinto a diferent folder click Browse and select another folder You can choose not to instal 5800 Audio Driver by clicking Cancel to Setup
40. rference will not occur Trade Name TASCAM in a particular installation If this equipment does Responsible party TEAC AMERICA INC cause harmful interference to radio or television reception which can be determined by turning the Address 7733 Telegraph Road Monte bello California U S A equipment off and on the user is encouraged to try to correct the interference by one or more of the Telephone number 1 323 726 0303 following measures This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation a Reorientor relocate the receiving antenna b Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected d Consult the dealer or an experienced radio TV technician for help CAUTION Changes or modifications to this equipment not expressly approved by TEAC CORPORATION for compliance could void the user s authority to operate this equipment Model number This appliance has a serial number located on the bottom panel Please record the model number and serial number and retain them for your records Serial number 2 TASCAM US 800 NOW Bb un IMPORTANT SAFETY INFORMATION
41. se Internet tools at the same time as an audio application processing may not be able to keep up the audio data Cubase LE 5 installation See the included Cubase LE 5 Quick Start Guide for details TASCAM US 800 13 Overview The Control Panel lets you make various settings related to how this unit functions On Windows the Control Panel icon appears in the notification area the system tray On Mac OS X the Control Panel is located wherever you put it during installation Double click the icon to open the control panel Other important audio settings for Mac OS X can be made using the Audio MIDI Setup program which is in the Applications Utilities folder Mac OS X control panel screens 14 TASCAM US 800 DEI Tra Control panel menus and settings Menu bar items Windows OS File Close Window Closes the window Config Mouse Wheel Sets the amount of movement per count when using a mouse scroll wheel to raise and lower the virtual faders Settings Step1 default value Step2 Step4 Step8 Latency According to the performance of the computer system you can change the size of the audio input and output signal buffer that the unit s driver stores temporarily Settings 192 240 288 336 384 576 default value All applications that connect to the US 800 must be closed before the latency can be changed Increase t
42. ses ASIO Record the output of an ASIO DAW into a WDM application Send the US 800 input signal to a WDM application Make settings in Route area which is second from the left after the TH area Click on a box in the to open a pull down menu Select the input signal for each interface from this menu The following settings are possible WDM input settings Setting Description Input default US 800 input signals setting ASIO ASIO application output signals ASIO input settings Setting Description Input default US 800 input signals setting WDM WDM application output signals When making settings be careful not to create a signal loop STATE section Windows only This shows system settings and driver and firmware versions LATENCY Sets the latency of the USB driver Settings 192 240 288 336 384 576 default value All applications that connect to the US 800 must be closed before the latency can be changed Increase the buffer size if the computer has insufficient processing power and noise occurs Increasing the buffer size however also increases latency audio signal delay Set this value to best suit your system DRV Ver This shows the driver version F W Ver That shows the firmware version installed in the unit System setting section Mac only This is the same as th
43. tal input is active Clock is set to pisITRL and the sample rate depends on the digital input When the digital input is not active Clock is set to Internal and the sample rate is set to i4 i kHz TASCAM US 800 29 F Transmitted Received Remarks Basic Channel At power ON Through Changed Mode At power ON Through Messages Altered JOOOCCOUEXOOEOUE Through Through Through Note X Number Range FARR Velocity Note ON X Note OFF After Touch Polyphonic Channel Pitch Bender ES Control Change Program Change Range AER Pape System Common Song Pos Tune System Clock Other Local on off Through All note off Active sensing Reset mu Mode 1 Omni on Poly Mode 2 Omni on Mono O Yes Mode 3 Omni off Poly Mode 4 Omni off Mono X No Through Through Through Through Through Through 30 TASCAM US 800 Please read this chapter if you are unable to use the unit properly even after setting it up following the procedures in this manual If you are still unable to resolve your problems please contact TASCAM customer support with the following information about the operating environment and details about the trouble Operating environment Computer manufacturer Model CPU Installed memory OS Applications used Antivirus software use Wireless LAN use Please see the back of this manual for contact information Installa
44. tion 9 0 W External dimensions W x H x D 262 x 41 x 152 mm without projections 262 x 44 x 165 mm with projections Weight 800g Operating temperature range 5 350 TASCAM US 800 35 Dimensional drawing Kensington lock hole E E a WL Y 262mm o m oe m om OOOO 116mm M4 mm screw hole Depth 4 0 mm max 108 4 mm Illustrations in this manual may differ in part from the actual product Specifications and the external appearance may be changed without notification to improve the product 36 TASCAM US 800 11 Specifications Block diagram pte eee eee eee eee eee eee 1 1 1 S navara 1 18 4 NIWLISIG 1 E SIXIN 1 1 8 2 NI Li e e pee 1 9 ANIT OIN 1 E 1 As 1 1 7 H ak LI 7 i 209185 1 A 110 TVLIDIA 1 1 1 S ANTT OIN TE J i 1 9 9 6 1 CEKIN i gt 1 A ASI NI NIIDI o o LI 1 O 2 pra TNO SINO Y pe EE i Oo EAT 1 un 1 ANITIN 1 el 1 fe 1 ITAS noz 1 O lt gt 1 LNO SHNOHd T A 1 1 U 1 1 ANTTIIN E s 6 2 1 SIXIN Y Yie 3NFOIW par Y 8 2 NI IVLIOIG LI T 7 va INO T 55 1 Z3 LI 1 i i H 1 ZH 7 LSNI OIN LOaTas 1 110 8NTT
45. tion fails Installation completes but the computer does not recognize the unit If some trouble is causing installation to fail or installation completes but the computer does not recognize the unit check the following 1 USBindicator lit Is the USB indicator on the front panel of the unit lit If the USB indicator is not lit confirm that the USB cable is properly connected Always use the included USB cable 2 Change the USB port Since the unit might not function properly with some USB ports try connecting to a different built in USB port on the computer and reinstall the driver when using Windows Try again after disconnecting other USB devices Keyboards and mice can be left connected Do not use a USB hub Always connect the unit directly to a built in USB port on the computer 3 Stop other software running in the background Since antivirus software and other software that runs in the background can interfere with installation stop other software before beginning installation See 3 Installation on page 10 of this manual for how to install and uninstall the driver There is no sound even when audio is playing back The audio output must be set on the computer Please confirm the following while the unit is connected to the computer Note that after making the following settings sound will be output through the unit but no sound will be output by the computer s speakers or headphone
Download Pdf Manuals
Related Search