Home

SimPal-B3 UserManual 20130702

1. Pressing a number button to choose the zone which is waiting for removing the sensor Choosing a zone Confirm ENTER The zone numbers which have been paired sensor will display such as The zone number will flash The sensor will be removed from the zone and then the zone number will display as a black number such as SIMPal BS GSM Alarm System User Manual 2 Method 2 By SMS command The user sends following SMS message in order to Removing the sensor from a zone 26 ZoneNumber 14 Removing all sensors from the Panel 26 15 4 3 Renaming the sensor of a zone The user sends following SMS message in order to Renaming the sensor of a zone 16 274 ZoneNumber SensorDescription ZoneNumber is one digit zone number which the sensor is loaded SensorDescription is used for identify sensor It can be numbers and letters 4 4 Special sensors The Wireless Alarm Panel supports up to 8 special sensors which is paired with the Panel but their information will not display on the zone 4 4 1 24 hour sensor No matter what working mode the Wireless Alarm Penal is working SIMPal BS GSM Alarm System User Manual in if the 24 hour sensor is triggered the Panel will alarm unconditional such as smoke sensor gas sensor etc The working status of 24 hour sensor do not show on the LCD screen When it triggers alarm the Panel will send notification message by
2. uuuussssse 39 SIMPal BS GSM Alarm System User Manual 5 3 5 Acoustic amp Optical Alarm ER RENBE 5 3 6 The audible countdown Beeper 0aaaaaaaaaanei 40 5 3 7 Key tones of the Panel oooooossse te nananana 41 5 3 8 Backlight of the Panel i 5 3 9 SMS notification upon the power supply changing 42 5 3 10 Getting temperature data soooouossn nenne 5 3 11 Temperature alarm sss 5 3 12 Weak GSM signal strength alarm 5 3 13 Check working status of the Panel ee 44 5 3 14 Resetting the Panel S v 7 5 3 15 Language settings 0neranenenenenananan anna nana nenen Appendix SMS commands list oosososssn annan 46 SIMPal BS GSM Alarm System User Manual Chapter 1 General system overview 1 1 Interview Thank you for purchasing the SimPal B3 The SimPal Wireless Alarm System is a quality security system with a wide range of user friendly features The system is controlled by a Wireless Alarm Panel which gathers information from wireless sensors placed around and at the entry points of your home or office If the Wireless Alarm Panel detects somebody moving or a security exceptions the LCD display will flash and the siren will sound ASIM card can be used in the Panel to send out the alarm message by SMS or making emergency phone calls The user calls the Panel to listen in live voice or communic
3. 26 Removing all keychain remote controls 27 Setting entry delay 28 Setting exit delay 29 Set time period to arm the Penal 30 Enable timing arming the Panel 31 Disable timing arming the Panel 32 Siren sounded time 33 Activate the SMS notification upon sensor alarm Default 34 No SMS notification upon sensor alarm 15 1 SensorDescription 1 OH 1 15 2 SensorDescription 28 Time 29 1 29 0 15 2 24 SensorDescription 24 17 1 6 1 Time 1 6 2 Time 22 WorkDay ArmTime1 DisarmTime1 ArmTime2 DisarmTime2 23 1 23 0 12 time 18 1 18 0 SIMPal BS GSM Alarm System User Manual noin Command 35 Activate the SMS notification upon doorbell alarm when in ALERT or 19 1 HOME mode 36 No SMS notification upon doorbell alarm when in ALERT or HOME mode 19 0 Default 37 Activate call notification upon alarm Default 38 No call notification upon alarm 20 0 39 Activate call notification upon 20 1 doorbell alarm HAI 40 No call notification upon doorbell 21 0 alarm Default 41 Activate arming disarming by 432818 call Default 42 Deactivate arming disarming by 432808 call 43 Activato the audible countdown 409418 when entering Default 44 Mute the audible countdown when 409408 entering 45 Activate the key tones 10 1 46 Mute the key tones Default 10 0 47 Turning on the backlight Default 1
4. 5 The FamilyNumber should be the Family user s mobile phone number SIMPal BS GSM Alarm System User Manual 3 6 Change the password In order to ensure your privacy and safety during the use of this Panel it is recommended that you change the password There are two methods to change the password Method 1 Change the password on the keypad STANDBY mode Unlock the keypad Set the LCD display password flashes with 1 Ful 1 be LCD d display flashes with 2 ENTER New password ewer ENTER New password ewer Method 2 The user sends following SMS message in order to Change the password 04 oldpasswordi tnewpassword 6 The password is a four digit number The original password is 1234 SIMPal BS GSM Alarm System User Manual 3 7 Entering STANDBY status In STANDBY mode the Wireless Alarm Panel is prepared for mode selection and the Panel cannot send out alarm except special sensor alarm and doorbell The LCD screen will display the number of sensors which were paired with the Panel There are three methods for entering STANDBY status Method 1 By the keypad Entering Password orl Ba Bo N evren STANDBY mode Method 2 By SMS command The user sends following SMS message in order to Entering STANDBY status 02 7 Method 3 By pressing DISARM button on the keycha
5. SMS or make phone call to the user The user sends following SMS message in order to Pairing a 24 hour sensor 15 1 SensorDescription 17 Removing a 24 hour sensor 15 1 18 4 4 2 Accompany sensor An accompany sensor could be a PIR motion sensor which be used to take care of the elderly and children If the Panel do not receive the accompany sensor alarm signal within a preset period of time the Panel will send notification message by SMS or make phone call to the user The user sends following SMS message in order to Pairing an accompany sensor 15 2 SensorDescription 19 Set the time period for accompany sensor 28 Time 20 Activate the accompany sensor 29 1 21 Deactivate the accompany sensor 29 0 22 Removing all accompany sensors 15 2 23 SensorDescription is used for identify different accompany sensor It can be numbers and letters The Time is a minimum time period which the Panel receives alarm signal from accompany sensor Its values should be in the range from 30 300 minutes The default value is 30 minutes Note The alarm signal from all activated accompany sensors SIMPal BS GSM Alarm System User Manual could be a valid signal within the preset time period 4 4 3 Doorbell sensor When the Panel receives signal from doorbell sensor the doorbell rings will be sound unconditional The user sends following SMS message in order to Pairing a doorbell sensor 24 SensorDescriptio
6. The wireless alarm panel should be placed within a few feet of an electrical outlet where it is SIMPal BS GSM Alarm System User Manual easily accessible Mark on the wall the points for drilling holes for the wall plugs and mounting screws Drill the holes insert wall plugs and locate the mounting screws for the Wireless Alarm Panel Drive in screw to fix the magnet on wall Mount the Wireless Alarm Panel onto the wall SIMPal BS GSM Alarm System User Manual Chapter 3 Basic use and settings 3 1 User authorization level There are two user levels each with a different authorization level namely Master and Families Table 3 1 the difference in authority for Master and Families users Change authority password Receive SMS alarm Automatic Alarm Receive alarm calling Receive SMS Emergency alarm Receive emergency calling Call the camera to listen in live voice Call the camera to listen in and talk with the Panel area Set Wireless Alarm Panel working mode by SMS command 3 2 About the SMS Commands Master and families users SMS command format code content SIMPal BS GSM Alarm System User Manual The password must be a four digit number The original password is 1234 The maximum digits that are allows for the phone number is sixteen After receipt of the command a SMS reply will be sent to user s mobile phone No allow any space within the comm
7. be adjusted to between 0 60 seconds Method 1 By the keypad Password or D D Bel B Bo STANDBY mode ENTER The LCD screen flashes with the number of seconds B E ee currently set for the y setlings Exit Delay Default setting is 30 seconds The Exit Delay time will be adjusted between the adjustable range of 0 60 seconds Each time D is pressed the Exit Delay is increased by a further 10 seconds Setting Exit Delay SIMPal BS GSM Alarm System User Manual Return the Panel to Conlin STANDBY mode ENTER Method 2 By sending SMS message The user sends following SMS message in order to Setting exit delay 16 2 Time 28 The Time values should be in the range from 0 60 second s 0 means no entry delay 5 3 Timed arming the Panel The Wireless Alarm Panel will arm automatically according to the schedule 5 3 1 Set time period to arm the Panel The user sends the following SMS message in order to Set time period to arm the Penal 22 WorkDay ArmTime t Disarm Time t ArmTime2 DisarmTime2 29 Up to 2 periods be allowed per workday Each period time should set by ArmTime DisarmTime WorkDay single digit in the range of 0 to 9 The following table contains the descriptions of each value Sunday Monday Tuesday Wednesday Thursday Friday Bj elmu j
8. is prepared for alarm if any of the sensor is triggered alarm The LCD screen will display HOME icon meanwhile each zone can be set working in the ARM or ALERT mode The 1 8 zone number will display as a black number ALERT mode or a white number with black background ARM mode When the zone working in ALERT mode alarms the doorbell will ring And when the zone working in ARM mode alarms the built in siren will be sound There are two methods for entering HOME mode Method 1 Entering HOME mode by the keypad HOME D D Entering Password or HOME mode All the numbers of Bo m Do zone which have settings been paired sensor will display such as Preset the zone which working in HOME mode SIMPal BS GSM Alarm System User Manual Password orl g Dr Bo Do 4 Pressing number buttons to cancel the zone setting of HOME mode Pressing again will preset the zone working in ARM mode Pressing the third time zone will preset the working in ALERT mode STANDBY mode HOME mode settings Zone exits HOME mode Zone enters ARM mode Zone enters ALERT mode HOME The numbers of zone which do not work in HOME mode will flash The zone number will display flash Numbers of zone which be set working in ARM mode will display as a black background number Numbers of zone which be set working in ALERT m
9. 3 1 48 Turning off the backlight 13 0 49 SMS notification upon the power 435418 supply changing Default 50 No SMS notification upon the 35 0 SIMPal BS GSM Alarm System User Manual L Fenton Command power supply changing 51 Get the temperature data from the built in thermometer 52 Get the temperature data from the external wireless thermometer 53 Enable over temperature alarm 54 Set limits of temperature for built in thermometer 55 Set limits of temperature for external thermometer 56 Disable the alarm upon going beyond limits temperature 57 Get the GSM signal strength data 58 Activate the weak GSM signal strength alarm Default 59 Deactivate the weak GSM signal strength alarm 60 Check the Panel operating status 61 Check the Panel operating status 30 30 2 31 1 31 2 MinTemp MaxTem pt 31 3 MinTemp MaxTem pt 31 0 36 HIGH1H HIOHOH O7 08 Password SimPal B3 GSM Alarm System
10. NDBY Ba Dao ENTER mode The backlight will D Backlight flash red one time settings that means it is turning on Press again will Turning on off The backlight will turn on or tum off the the backlight turning off backlight Method 2 By sending SMS message The user sends the following message in order to Turning on the backlight Default 13 1 47 Turning off the backlight 13 0 48 SIMPal BS GSM Alarm System User Manual 5 3 8 SMS notification upon the power supply changing The Wireless Alarm Panel will notify the user whenever the power supply changes status If the power adapter is disconnected or when a failure of the AC power occurs the Panel will notify the user External power cut The device is operating on battery If the Panel is again connected to the external power or the AC power is available again a notification will be sent to the user stating The device is now resuming the use of external power source The user sends the following message in order to SMS notification upon the power supply changing Default 35H1 49 No SMS notification upon the power supply changing 35 0 50 5 3 9 Getting temperature data The Wireless Alarm Panel has a built in thermometer It also supports an external wireless thermometer which should be placed near the Panel The external wireless thermometer needn t pair with the Panel The user sends the foll
11. SimPal B3 GSM Alarm System User Manual SIMPal BS GSM Alarm System User Manual CONTENTS Chapter 1 General system overview 5 Ped AMTSIVISWnnnmmura daa eg a Dana Sa e AATE NETS aN Da a ai e Tag na aaa 5 1 2 Package contents sesane ran anane anana nen aa nana anane 5 1 3 Wireless alarm panel instruction cccceeeeeeeeeeeteeeeeeees 6 1 31 E CD dis playin aaa eres Scene E E 7 13 2 Keypad s Pinus aan arnt dee a aa a a 10 1 3 3 ed 1 00k 0 0 re 11 Chapter 2 Installation 0 e 2 1 Installing the wireless alarm panel 2 2 Wall mounting the wireless alarm panel ceee 12 Chapter 3 Basic use and settings osssosssn nenne 14 3 1 User authorization level a0eanenaann n aranne ene 14 3 2 About the SMS Commands asanrana anane nan ran nenen 14 3 3 Add a Master number to the Wireless Alarm Panel 15 3 4 Change the Master number cceeeeeeeeeeeeeteeeeeeeeeeeee 15 3 5 Define the Family user oouuuuuss sen n nana anna 16 3 6 Change the password oooooussssss ana n nn ana a nane 17 3 7 Entering STANDBY status n nananana 18 3 8 Arming the Panel oooosossssso naa a a n n anane nanan 18 3 9 ALERT Doorbell MOde ooooousssss a n n anana anae 20 3 9 1 Entering ALERT mode aaneaeenananan nananana 20 3 9 2 Exiting ALERT mode 1 0 0 cece cece eens naen ne nene
12. Y mode Method 2 By sending SMS message The user sends following SMS message in order to set Siren sounded time 12 Time 32 The Time values should be in the range from 0 6 minute s 0 means no siren sound Default Time value is 1 5 3 3 2 SMS notification upon alarm When the Wireless Alarm Panel is triggered alarm by a sensor it will send SMS notification message to the user s mobile phone SIMPal BS GSM Alarm System User Manual The user sends the following message via SMS to the Wireless Alarm Panel in order to Activate the SMS notification upon sensor alarm Default 18 1 33 No SMS notification upon sensor alarm 18 0 34 Activate the SMS notification upon doorbell alarm when in ALERT or HOME mode 19 1 35 No SMS notification upon doorbell alarm when in ALERT or HOME mode Default 19 0 36 5 3 3 3 Call notification upon alarm When the Wireless Alarm Panel is triggered alarm it will make phone call to the user s mobile phone The user sends the following message via SMS to the Wireless Alarm Panel in order to Activate call notification upon alarm Default 20 1 37 No call notification upon alarm 20 0 38 Activate call notification upon doorbell alarm 21 1 39 No call notification upon doorbell alarm Default 21 0 40 5 3 4 Arming Disarming the Panel by call The Wireless Alarm Panel can be set arming or disarming by making phone call remotely by the user Th
13. ands The symbol must not be ignored when typing an SMS command 3 3 Add a Master number to the Wireless Alarm Panel Only one Master mobile number Master number is allowed for the Panel The Master user must edit and send the following SMS to the Panel via his her mobile phone the phone number will be the Master number in order to Add a Master number to the Panel 00 1 3 4 Change the Master number The user sends following SMS message in order to Change the Master user s number 14 NewMaster 2 SIMPal BS GSM Alarm System User Manual The NewMaster should be the Master user s mobile phone number The CountryCode means the access code for country calling For example In Germany if the user mobile number is 01712345678 then this command should be 14 491787654321 49 is the country code of Germany 1787654321 is new Master number In some countries all that necessary is to send Area Code the number For example the command 14 1787654321 would be sufficient 3 5 Define the Family user Up to 4 Family users are set by the Master user The Master user edits and sends the following SMS to the Panel in order to Add a Family number to the Panel 06 FamilyNumber 3 If the Family number guality is over 4 old Family number must be removed at first and then new Family number can be set Delete a Family number 11 FamilyNumber 4 Delete all Family numbers 11
14. ate with the morning area Details of the functioning and advanced operation of this device are described in this instruction manual 1 2 Package contents Please check that all of the following items were included in the package before installing the system SIMPal BS GSM Alarm System User Manual J W Walls 6 Hitti tis N 4 VN kone a O ETT O Alarm panel 1 unit amp Door Window sensors 433Mhz 1 units PIR detector 433Mhz 1 units Keychain remote controls 433Mhz 2 units AC power adapter for wireless alarm panel 12V 1 unit User manual 1 unit 1 3 Wireless alarm panel instruction SIMPal BS GSM Alarm System User Manual LCD display 1 3 1 LCD display SIMPal BS GSM Alarm System User Manual sll 1 2 3 4 5 6 7 8 5 Da at ARM HOME ALERT m O IA Sos Tull GSM Signal strength only when the SIM card installed 1 1213 4 5 6 7 8 1 8 zone status The Wireless Alarm Panel supports up to 8 zones Each zone supports 1 sensor A doorbell is recognized as a sensor After the sensor is loaded onto the zone and the alarm panel entering into STANDBY status the zone number will display accordingly ARM a ARM mode icon It shows that the alarm panel is working in ARM mode When any of the sensor be triggered the built in siren in the alarm panel will emit loud sound Meanwhile all zone numbers will be displayed as a white number with black background such a
15. d for alarm if any of the sensor is triggered alarm The LCD screen will display ALERT icon and numbers of zone will display as a black number When the Panel alarms the doorbell will ring 3 9 1 Entering ALERT mode Method 1 Entering ALERT mode by the keypad ALERT Password on D E Zone enters Numbers of zone D which be set Bz Do ALERT mode working in ALERT mode will display as a black number such as 2 Preset the zone which working in ALERT mode SIMPal BS GSM Alarm System User Manual Password orl g D B STANDBY D gt Do evren mode ALERT ALERT mode a N The zone numbers settings which do not work in ALERT mode will flash Pressing number buttons will cancel the ALERT mode setting for the zone Sensor exits Numbers of zone ALERT mode will cancel Numbers of zone which be set Zone enters working in ALERT ALERT mode mode will display as a black number such as 2 Pressing again to preset the zone working in ALERT mode Method 2 By SMS command The user sends following SMS message in order to Enter ALERT Mode 03 1 9 Method 3 By pressing ALERT button on the keychain remote control 3 9 2 Exiting ALERT mode Refer to Chapter 3 7 Entering STANDBY mode SIMPal BS GSM Alarm System User Manual 3 10 HOME mode 3 10 1 Entering HOME mode In HOME mode the Wireless Alarm Panel
16. e the weak GSM signal strength alarm Default SIMPal BS GSM Alarm System User Manual 36 1 58 After receipt of this command if the GSM signal strength level is below 10 the Panel will send weak GSM signal alarm message to the user by SMS Deactivate the weak GSM signal strength alarm 36 0 59 5 3 12 Check working status of the Panel The user sends the following message in order to Check the Panel operating status HO7H 60 After receiving the SMS commands the Panel will reply one SMS message of working status checking for Master number Arming Disarming mode status Temperature and GSM strength level 5 3 13 Resetting the Panel This function resets all programmed settings of Wireless Alarm Panel to their original factory values including cleaning all user number timing parameter and temperature parameter etc If the setting status is wrong or the malfunctions can t be corrected the Panel can be restored to its original factory status to make it work normally The connected sensors will not clean after resetting the panel Method 1 Press the SET key of the Panel for 5 seconds Method 2 The user sends the following message in order to Check the Panel operating status 08 Password 61 After receiving the SMS commands a long Beep tone will be heard SIMPal BS GSM Alarm System User Manual it means resetting the Panel successfully and then the Panel will reply one message via SMS 5 3 14 Language s
17. e user sends the following message via SMS to the Wireless Alarm Panel in order to SIMPal BS GSM Alarm System User Manual Activate arming disarming by call Default H32 1 41 Deactivate arming disarming by call 32 0 42 5 3 5 The audible countdown Beeper When the Wireless Alarm Panel is ARMED the audible countdown can be silenced by pressing the D button during the countdown To reactivate the audible countdown simply press button again Method 1 By the keypad Password DDB D Do Audible Ba countdown settings Press D again will Muting the mute or activate the audible audible countdown countdown Method 2 By sending SMS message The user sends the following message in order to STANDBY mode ENTER Audible countdown is default activated Activate the audible countdown when entering Default OO 1 43 Mute the audible countdown when entering 09 0 44 SIMPal BS GSM Alarm System User Manual 5 3 6 Key tones of the Panel When the buttons of the Panel is pressed the key tones will default be sound The user sends the following message in order to Activate the key tones 10 1 45 Mute the key tones Default 10 0 46 5 3 7 Backlight of the Panel The backlight of the Panel LCD screen can be turn on off by the following two methods Method 1 By the keypad Password orld D STA
18. ed 7 l SOS icon This icon appears when the Wireless Alarm Panel is making a panic phone call or the user is listening in the Panel area by phone 1 3 2 Keypad D J ere 0 9 numeric buttons and 6 function buttons for entering the number and setting the working modes SIMPal BS GSM Alarm System User Manual 1 3 3 Beep tone One beep indicates that you entered a valid password Two beeps indicate that an invalid operation was performed SIMPal BS GSM Alarm System User Manual Chapter 2 Installation 2 1 Installing the wireless alarm panel Unscrew the battery compartment and remove the battery cover by pulling up from the middle hollow SIM card Firstly make sure the GSM SIM card have Caller ID functions activated and the PIN code of the SIM must be deactivated Contact your GSM network service provider for support Insert the SIM card into the slot Note the metal circuit board is face down Insert a back up battery noting the polarity and plug the AC adaptor into the Wireless Alarm Panel Power on off Turn the power switch to On position the Wireless Alarm Panel will power up Turn the power switch to OFF position and it will power off Installing the battery cover by upward bending to make both sides buckle into the slot drive in the screws and connect the AC adaptor to a wall socket 2 2 Wall mounting the wireless alarm panel Locating the wireless alarm panel
19. emote control sound Method 2 By sending SMS message The user sends following SMS message in order to Removing all keychain remote controls 17 26 SImPal K3 GSM Alarm System User Manual Chapter 5 Advanced settings 5 1 Adjusting entry delay The default setting of the Wireless Alarm Panel allows the user 30 seconds to enter the property and DISARM the alarm before it is triggered However this Entry Delay can be adjusted to between 0 60 seconds Method 1 By the keypad Presetting entry delay Password orl D STANDBY Ba Doh ENTER mode The LCD screen flashes with the number of seconds b ev ee currently set for the y setings Entry Delay Default setting is 30 seconds n The Entry Del Each time Dr is E SENIN say time will be adjusted pressed the Entry Delay Setting entry ie a bya furth dela between the P OSAS yee y adjustable range of 10 seconds 0 60 seconds SImPal K3 GSM Alarm System User Manual eve Confirm Return the Panel to STANDBY mode Method 2 By sending SMS message The user sends following SMS message in order to Setting entry delay 16 1 Time 27 The Time values should be in the range from 0 60 second s 0 means no entry delay 5 2 Adjusting exit delay The default setting of the Wireless Alarm Panel allows the user 30 seconds to exit the property before the alarm is ARMED However this Exit Delay can
20. ettings The user sends the following message in order to Choose English machine language 37 1 62 Choose optional machine language 37 0 63 SIMPal BS GSM Alarm System User Manual Appendix SMS commands list Funetion Command 1 Add a Master number to the Panel 2 Change the Master user s number 3 Add a Family number to the Panel 4 Delete a Family number 6 Change the password 7 Entering STANDBY status 8 Entering ARM mode 5 Delete all Family numbers 9 Entering ALERT mode 10 Entering HOME mode 11 Deactivate the speaker and then listening in the Panel area 12 Activate the speaker and then talking with the Panel area Default 13 Loading sensor 14 Removing the sensor from a zone 15 Removing all sensors from the Panel 16 Renaming the sensor of a zone 00 14 NewMaster 06 FamilyNumber 11 FamilyNumber 11 04 O0ld new 02 01 03 1 03 2 25 0 25 1 05 ZoneNumber Sensor Description 26 ZoneNumber 13 27 ZoneNumber Sensor Description SIMPal BS GSM Alarm System User Manual Fenton Command 17 Pairing a 24 hour sensor 18 Removing a 24 hour sensor 19 Pairing an accompany sensor 20 Set the time period for accompany sensor 21 Activate the accompany sensor 22 Deactivate the accompany sensor 23 Removing all accompany sensors 24 Pairing a doorbell sensor 25 Removing all doorbell sensors
21. in remote control 3 8 Arming the Panel In ARM mode the Wireless Alarm Panel is prepared for alarm if any ARM of the sensor is triggered alarm The LCD screen will display 4 icon and numbers of zone which be set working in ARM mode When the Panel alarms the built in siren will be sound and the background light of LCD screen will flashing red SIMPal BS GSM Alarm System User Manual There are three methods for entering ARM mode Method 1 Entering ARM mode by the keypad Numbers of zone which be set Password old D E Entering ARM a D D mode working in ARM 3 WD mode will H Such as Preset the zone which working in ARM mode Password or D Be STANDBY Ba Doh evren mode ARM a ARM mode The zone numbers Settings whic o no selected in ARM mode will flash Pressing number buttons will cancel the ARM mode setting for the zone Sensor exits Numbers of zone ARM mode will cancel Numbers of zone Pressing again to preset Zon enters which be set the zone working in ARM working in ARM ARM mode mode mode will appear Such as Method 2 By SMS command SIMPal BS GSM Alarm System User Manual The user sends following SMS message in order to Enter ARM mode 01 8 Method 3 By pressing ARM button on the keychain remote control 3 9 ALERT Doorbell mode In ALERT mode the Wireless Alarm Panel is prepare
22. larm Panel will be in emergency mode alarm unconditionally when the following two processes happen A Method 1 bsos button on the keychain remote control be pressed Method 2 Sending emergency alarm by the keypad Password or Dr Be Unlock the Ba Bo ENTER keypad Pressing Can button for Emergency 3 seconds alarm SIMPal BS GSM Alarm System User Manual Chapter 4 Sensors and keychain remote controls 4 1 Pairing sensors User can pair wireless sensor with panel by following two methods Method 1 Loading sensor by keypad Password orld D E STANDBY Ba Bo enren mode The zone numbers which have been paired sensor will Entering display with black Po sensor setting background such as mode ET otherwise they will display with a black number such as 2 Pressing a number button to choose the Choosing a The zone number zone whichis prepare zone will flash for loading a new sensor SIMPal BS GSM Alarm System User Manual The zone number which has been successfully loaded sensor will display with black background such as The user needs to make the sensor work and Loading transmit signal to be sensor studied by the Panel Method 2 By SMS command 1 The user sends following SMS message in order to Change the password 05 ZoneNumbertSensorDescriptiont 13 ZoneNu
23. mber is one digit zone number which hasn t been loaded a sensor SensorDescription is used for identify different sensors affiliated with each zone It can be numbers and letters 2 When the Panel has received the SMS command it will then send a notification message via SMS to the user stating Waiting to load wireless sensor make the sensor work immediately otherwise it will inform the zone numbers which haven t been loaded a sensor and then user must resend a correct command to the Panel 3 The user needs to make the sensor work and transmit signal to be studied by the Panel E g For a wireless door sensor open and close the door once to send the signal to the Panel 4 When the Panel receives the sensor signal it will send a notification message via SMS to the user The zone number which has been successfully loaded sensor will display with black background such as i 5 The Panel will emit Beep Beep tone if the user want to load SIMPal BS GSM Alarm System User Manual an paired sensor which has already been loaded onto the other zone ENTER 6 Press manually Otherwise the Panel will automatically after 30 seconds button of the Panel to exit the loading mode exit the loading mode 4 2 Removing sensor from the Panel Method 1 Removing sensor by the keypad Ba Password or D STANDBY D Bo ENTER mode Entering sensor setting mode
24. n 24 Removing all doorbell sensors 24 25 SensorDescription is used for identify different doorbell sensor It can be numbers and letters 4 4 4 Keychain remote control Cizom parti tutor fam pare tunon Remo contro hndkaker Erargenoy buten Arm the Panel button Pressing this button to arm the Panel The Panel will enter the preset working mode such as ARM mode ALERT mode or HOME mode Disarm the Panel button Pressing this button to disarm the Panel The Panel will enter STANDBY mode SIMPAal BS GSM Alarm System User Manual Panic button Pressing this button the Panel will be triggered emergency alarm There are two methods for pairing removing the keychain remote control Method 1 By the keypad Pair keychain remote control Password or D g Bo Bo Bea ENTER ye Press any button of keychain remote control STANDBY mode Entering remote control settings Pairing remote One BEEP tone be control sound The Panel will emit Beep Beep tones if the keychain remote control has been paired with the Panel Remove keychain remote control by the keypad Password or D Bo Do De ENTER ee STANDBY mode Entering remote control settings SIMPal BS GSM Alarm System User Manual Press D lt button and Removing One BEEP tone be hold for 3 seconds r
25. n ene 21 SIMPal BS GSM Alarm System User Manual 3 10 HOME mode 3 10 1 Entering HOME mode 3 10 2 Exiting HOME mode ccccccesceeeeeeeeeeeteeeeeeeeeees 3 11 Telephone communication with the Panel area 1 24 3 12 Emergency alarm sssesenenenenanena nenen a nawan anana nana nenen 24 Chapter 4 Sensors and keychain remote controls 26 4 1 P iting sensOrs isa janan aaa gan a TENG ag a Kana sab nga a NE aaa ag 26 4 2 Removing sensor from the Panel 28 4 3 Renaming the sensor of a ZONE s e 29 4 4 Special Sensors ssaenraaanan anaa anane anana nn nn anana 29 AAT DANOWN SONSOM Taek maan aaa ag ana gaw 29 4 4 2 ACCOMPANY sensor aasanenenen nn nenen a rennene nane 30 4 4 3 Doorbell SENSO iiinis KANE Gawa kagawa ANAN AN aka 31 4 4 4 Keychain remote Comntrol cccccceeseeeeeeeeeeeneteeeeees 31 Chapter 5 Advanced settings oooossossss naene neen 34 5 1 Adjusting entry delay ouuuuussss aa n n nennen 5 2 Adjusting exit delay 5 3 Timed arming the Panel 5 3 1 Set time period to arm the Panel cceeeeeee 36 5 3 2 Enable Disable timing arming the Panel 2487 5 3 3 Alarm Sengsara aana sani Tan kaa akan a a Ka 37 5 3 3 1 Built in siren warning tone upon alarm triggering 37 5 3 3 2 SMS notification upon alarm 38 5 3 3 3 Call notification upon alarm 39 5 3 4 Arming Disarming the Panel by call
26. o SIMPal BS GSM Alarm System User Manual 6 Saturday 7 Everyday 8 Monday to Friday 9 Saturday and Sunday ArmTime and DisarmTime Be consists of 4 digits hh mm and works on a 24 hour clock For example 0000 means time 00 00 hh mm 2359 means time 23 59 hh mm The ArmTime and DisarmTime should be in the same day and the DisarmTime must be later than ArmTime during the same period 5 3 2 Enable Disable timing arming the Panel The user sends the following SMS message in order to Enable timing arming the Panel 23 1 30 Disable timing arming the Panel 23 0 31 5 3 3 Alarm settings 5 3 3 1 Built in siren warning tone upon alarm triggering In ARM mode when the Wireless Alarm Panel is triggered alarm the built in siren will be sound 110dB Method 1 By the keypad Password or g Bo STANDBY D gt Bo enren mode SIMPal BS GSM Alarm System User Manual Each time is pressed the time increased by a further 1 minute ENTER Entering time settings Setting siren sounded time Confirm The LCD screen flashes with the number of minutes currently set for the siren sounded time Default 1 minute when the Panel alarms The siren sounded time will be adjusted between the adjustable range of 0 6 minutes Time 0 means the siren will not sound when the Panel alarms Return the Panel to STANDB
27. ode will appear Such as 2 Method 2 By SMS command The user sends following SMS message in order to Enter HOME Mode HO3H2H 10 SIMPal BS GSM Alarm System User Manual 3 10 2 Exiting HOME mode Refer to Chapter 3 7 Entering STANDBY mode 3 11 Telephone communication with the Panel area The Master and Family users call the Wireless Alarm Panel after which it will answer automatically The user can then listen in the live audio in the monitoring area Only one line can be connected to the Panel at a time When the Master user calls the Panel its Speaker is default opening so that the Master user can communicate with the Panel area The Master user sends following SMS message in order to Deactivate the speaker and then listening in the Panel area 25 0 11 Activate the speaker and then talking with the Panel area Default 25 1 12 Note For the calling made by the Panel emergency alarm the speaker could not deactivate by command 12 3 12 Emergency alarm When the emergency alarm is triggered the Wireless Alarm Panel will dial the Master and Family users number The Panel will repeat this process 3 times until someone answers After 3 attempts if there is no answer the Panel will automatically stop dialing and SIMPal BS GSM Alarm System User Manual revert to its preset mode When someone answers the call he she will be able to listen in the live audio and talk with the Panel area The Wireless A
28. owing message in order to Get the temperature data from the built in thermometer 30 1 51 Get the temperature data from the external wireless thermometer 30 2 52 After receipt of the command the Panel will send the temperature data via SMS message to the user SIMPal BS GSM Alarm System User Manual 5 3 10 Temperature alarm The Wireless Alarm Panel has a built in thermometer and it also supports an external wireless thermometer A range of temperature can be pre set for the thermometers In this case if the surroundings temperature is detected out of the pre set temperature range the Panel will auto send the SMS alarm message to the user s mobile phone The user sends the following message in order to Enable over temperature alarm 31 1 53 Set limits of temperature for built in thermometer 31 2 Min Temp MaxTemp 54 Set limits of temperature for external thermometer 31 3 Min Temp MaxTemp 55 MinTemp and MaxTemp The values can be set within the range of 20 to 60 centigrade degree Default MinTemp is 20 and MaxTemp is 30 centigrade degree Disable the alarm upon going beyond limits temperature 31 0 56 5 3 11 Weak GSM signal strength alarm The Wireless Alarm Panel can be set sending out alarm via SMS message when the GSM signal strength is too weak to maintain normal working status The user sends the following message in order to Get the GSM signal strength data 36 57 Activat
29. s 815 ALERT ALERT mode doorbell icon It shows the Wireless Alarm Panel is working in ALERT mode When any of the sensor be triggered the doorbell will ring Meanwhile all numbers of zone SIMPal BS GSM Alarm System User Manual which work in ALERT mode will display as a black number such as 2 HOME HOME mode icon It means the Wireless Alarm Panel is working in HOME mode Each of the zone can be set working in the ARM or ALERT mode The 1 8 zone number will display as a black number ALERT mode or a white number with black background ARM mode muk Battery icon This icon shows power status when the AC power supply is unplugged or interrupted 3 7V battery functions as back up only The flashing icon means low battery and the alarm panel will shut down automatically mv AC Adaptor icon This icon will appear when the AC adaptor to the alarm panel is connected to a wall socket S Numbers It shows number of phone number password code temperature or time counting down for arming disarming G Keypad lock This icon appears when the keypad operation pauses for more than 10 seconds and the keypad is locked Key in the password code to unlock the keypad SIMPAal BS GSM Alarm System User Manual z Setting icon This icon appears when the Wireless Alarm Panel works in STANDBY mode and the button is pressed It means the working mode of the Panel can be set or the sensors can be load

SimPal-B3 UserManual 20130702

Contents

Download Pdf Manuals

Related Search

Related Contents