Helix Max - Opentip.com
Contents
1. L 55 watts 0 3 bar IPX3 230 V 50 Hz Lo AQUA MEDIC sm Gewerbepark 24 49143 Bissendorf Germany 4 Safety advice The radiation of the UV C lamps is dangerous Direct contact with eyes or skin can result in irre versible damages Therefore the unit must always be switched off before it is opened The units Helix Max 5 watts and Helix Max 9 watts and 11 watts are suitable for indoor use only The units may only be switched on when the water flow is on If used on a garden pond the units have to be switched off and removed during winter to prevent damages from frost The units may not be sub merged or operated under water 5 Connection The Helix Max are supplied with transparent connection pieces This allows to control the function of the bulbs blue light when the UV bulbs are on Depending on the installed pump and water flow the connection pieces should be cut to the best size metal saw The connections of the Helix Max can be rotated for 360 This allows an easy adaptation to the mounting conditions In any case the units have to be set up in a way that the outlet connection is at the highest point to avoid air to be trapped in the unit 1 Housing 2 Ballast 3 UVC Lamp 4 Connection pieces 5 Holding plate 6 Union nut 6 Maintenance and cleaning The UV C lamps have a life span of approx 8 000 hrs After 5 000 hrs the UV C output of the lamps decreases to 85 The lamps have to be c2. installation 3 Sizes technical data Helix Max sterilizers are produced in 6 sizes 5 watts 9 watts 11 watts with 2 m cable for fresh and saltwater aquariums 18 watts 36 watts and 55 watts with 10 m rubber cable and electronic ballast for garden ponds and for fresh and saltwater aquariums With electronic ballasts for longer life time of the bulbs and also a higher UV output For the different applications we recommend different aquarium pond sizes and flow rates In garden ponds the recommended flow rates will not result in a sterilization but the water is clarified by killing the microalgae ieee ee eee eee Pond Maximum 5 watts 25 1251 100 I h 50 250 200 I h 9 watts 125 2501 200 I h 250 500 500 I h 11 watts 150 350 I 300 I h 350 750 700 l h 18 watts 500 1 000 I 1 000 I h 500 1 000 1 000 I h 18 000 6 000 I h 36 watts 500 1 000 1 000 I h 1 000 2 000 2 000 I h 36 000 12 000 I h 55 watts up to 1 500 1 500 I h up to 3 000 3 000 I h 55 000 18 000 l h Helix Max Cable length Lamp type Max pressure Protection Power connection 5 watts 2m PL S 5 watts 0 3 bar IPX3 230 V 50 Hz 9 watts 2m PL S 9 watts 0 3 bar IPX3 230 V 50 Hz 11 watts 2m PL S 11 watts 0 3 bar IPX3 230 V 50 Hz 18 watts 10m PL L 18 watts 0 3 bar IPX3 230 V 50 Hz 36 watis 10m PL L 36 watts 0 3 bar IPX3 230 V 50 Hz 55 watts 10m PL
3. bo AQUA MEDIC en Gewerbepark 24 49143 Bissendorf Germany UV sterilizer Helix Max Operation manual GB Helix Max 55 W UV sterilizer for saltwater and freshwater aquariums and garden ponds This UV sterilizer is a quality unit If used correctly Helix Max kills microalgae and creates cristal clear water in aquariums and garden ponds It inactivates bacteria and other parasites and the risk for infec tion of the fish decreases It has been specifically developed for aquarium use has been designed and manufactured to the highest standards and has been extensively tested GBI ho AQUA MEDIC cn Gewerbepark 24 49143 Bissendorf Germany 1 Operating principle The UV sterilizer Helix Max clears the water with the help of ultraviolet radiation This radiation is emit ted by a special lamp The UV C radiation kills all forms of life that are directly exposed to the radia tion microalgae bacteria protozoa and other parasites The result is cristal clear water and healthy fish 2 Special features Spiral water flow The unique spiral water flow and the big volume of the Helix Max units ensure an optimum water clarification The water is directed in a spiral way around the quartz tube with a long contact time Due to this the UV radiation is used with maximum efficiency Rotable connections The inlet and outlet connections of the Helix Max can be rotated for 360 This saves space and fascilitates the
4. f your 40 Aaua Mevie GmbH product does not appear to be working correctly or appears to be defec tive please contact your dealer in the first instance Before calling your dealer please ensure you have read and understood the operating instructions If you have any questions your dealer cannot answer please contact us Our policy is one of continual technical improvement and we reserve the right to modify and adjust the specification of our products without prior notification AB Aqua Medic GmbH Gewerbepark 24 49143 Bissendorf Germany Technical changes reserved 8 2009
5. hanged regularly We recommend to clean the quartz tube whenever the lamps are changed 2 Switch the power off stop the water flow and drain the water from the unit dismount the water connections 3 Open the large screw cap Careful The lamp is fixed with the socket in the screw cap If the screw cap is open you can carefully remove the lamp 1 Housing 2 Plastic cover of the UV C lamp 3 UV C lamp 4 Lamp holder and end cap GB GBI Lo AQUA MEDIC cn Gewerbepark 24 49143 Bissendorf Germany 4 To clean the quartz tube it can be removed from the housing Normally it is very tight and has to be lifted up a little bit with a screw driver or a coin careful do not use too much force Take it out by hand The quartz tube can be cleaned with water and a soft cloth If there are calcium deposits on the tube it can be cleaned with vinegar or commercial decalcifiers Afterwards flush it with water The plastic end part of the quartz tube can be fitted with grease for easy remounting 5 The remounting is done in reverse order The quartz tube is pushed into the housing the lamp is fastened into the socket and both are carefully mounted in the housing The screw cap is fixed tight Finally the connection pieces are remounted and the hoses are secured with the clamps 6 The electronic ballast is main 7 a me enance tree It the lamp stops 3 Plastic end of the quartz tube working or does not start Should be fi
6. tted with grease before remounting i anymore although a new lamp is mounted the ballast has to be changed This has to be done by a specialist using original 4 amp 0 Aaua Menie parts only 7 Warranty Should any defect in material or workmanship be found within 12 months of the date of purchase do Aaua Mevie GmbH undertakes to repair or at our option replace the defective part free of charge always provided the product has been installed correctly is used for the purpose that was intended by us is used in accordance with the operating instructions and is returned to us carriage paid The warranty term is not applicable on the all consumable products Proof of Purchase is required by presentation of an original invoice or receipt indicating the dealer s name the model number and date of purchase or a Guarantee Card if appropriate This warranty may not apply if any model or production number has been altered deleted or removed unauthorized per sons or organisations have executed repairs modifications or alterations or damage is caused by accident misuse or neglect We regret we are unable to accept any liability for any consequential loss Please note that the product is not defective under the terms of this warranty where the product or any of its component parts was not originally designed and or manufactured for the market in which it is used These statements do not affect your statutory rights as a customer I
Download Pdf Manuals
Related Search