TS-ENC560 Manual - Technologic Systems
Contents
1. AC Power 1 Unplug the power cord from the power source 2 Disconnect the power cord from the rear panel of the enclosure Rev 1 2 TS ENC560 5 Technologic Systems Inc Components Standard Headers and Connectors Front Panel See Appendix A for a view of the enclosure s front panel Rear Panel TS Enclosure 560 Rear Panel Connectors The rear panel of the metal enclosure has three connectors and two additional elements as indicated in the above view Identifiers and a description for each are listed in the tables below Identifier Connector Description 1 Ethernet O 2 COM1 3 COM2 Additional Elements Identifier Description 4 12 38VDC and Power Indicator LED 5 Chassis Grounding Lug TS ENC560 6 TS Enclosure 560 User Manual Enclosure TS ENC560 Ethernet Port 0 Left and Right LEDs highlighted a Ethernet The Ethernet connector is a standard RJ 45 socket It can be used to connect a standard 10 100 Ethernet cable into the enclosed EPC Note The right side LED above the Ethernet port indicates a 100 Mbit link while the left side LED indicates network activity Both LEDs are highlighted red in the above graphic Rev 1 2 TS ENC560 7 Technologic Systems Inc Enclosure TS ENC560 COM1 Port Pin 1 highlighted a COMI COMI is brought in from the enclosed SBC This 9 pin SubD connector is industry standard for a PC The TxD RxD RTS CTS and ground pins are suppor2. available on our web site x Free technical support by phone fax or email a 30 day money back guarantee on evaluation units a One year full warranty TS ENC560 4 TS Enclosure 560 User Manual Installing the Enclosure Electrostatic Discharge ESD precautions Before performing any set up or placement procedures take the precautions outlined in this section Important l Be sure to take appropriate Electrostatic Discharge ESD precautions Disconnect the power cable at the rear panel of the enclosure before moving cabling or performing any set up procedures Setup and installation Instructions Follow these guidelines for safety and maximum product performance Aa Observe local health and safety requirements and guidelines for manual material handling A Set the enclosure on a level surface with adequate ventilation a Ensure the rubber feet are used for protection and stability on level surfaces a Wall mount the unit if placement on a level surface is not available or desired Setup Tools Depending on the placement and cabling of the enclosure you may need the following tools a Small flat blade screwdriver A Small Phillips screwdriver Setup Procedure After locating setting up grounding and cabling the enclosure 1 Apply power to the unit The amber colored LED on the rear panel should be lit 2 _ Monitor COM2 using a terminal emulator to verify that the enclosure is operating properly Disconnecting
3. Appendix A Enclosure Views Enclosure TS ENC560 Front Top View Enclosure TS ENC560 Rear Panel View Rev 1 2 TS ENC560 15 Technologic Systems Inc TS ENC560 Board TS ENC560 Board TS ENC560 16 TS Enclosure 560 User Manual Appendix B User Manual Revisions Date of Issue Revision Revision Number Comments January 2005 1 0 First release ER weblinks a a Mc di Rev 1 2 TS ENC560 17 Technologic Systems Inc Contact Information d Tec chnologic x SYSTEMS 16525 East Laser Drive Fountain Hills AZ 85268 TEL 480 837 5200 FAX 480 837 5400 info embeddedx86 com http www embeddedx86 com TS ENC560 18
4. Enclosure TS ENC560 User Manual d r echnologic SYSTEMS 16525 East Laser Drive Fountain Hills AZ 85268 TEL 480 837 5200 FAX 480 837 5400 inf m x m http www embeddedx86 com Technologic Systems Inc SYSTEMS A Kr Technologic COPYRIGHT 1998 2009 Technologic Systems Inc Enclosure 560 User Manual Rev 1 2 June 2009 Note A All modifications from previous versions are listed in Appendix B TS ENC560 2 TS Enclosure 560 User Manual Table of Contents Product EEN 4 IntroductiOl sein OL 4 Features and Bene tits isis iccsacassccnctcazinnatacececteiazsanatnceagentssasannanasiaedesensvanunaasseeteniazananaa 4 Related Products sanaaa an araara sxnntaissannacuastnnehitsanataescatendandndacoacicnensensanaieasceneads 4 S ftw re a d SUPPON GETT 4 Installing the Enclosure EF TN AFF ANFON 5 Electrostatic Discharge ESD precautions ss 5 Setup and Installation Instructions KEEN 5 Setup so oi eL EE 5 Disconnecting AC POWEeT iu hentai lun lad ire den ibn ea REEE 5 KEES eege ee EFE DN teens termes te 6 Standard Headers and Connectors ss 6 Front mL FEST PHRYFED FEWN 6 Rear Panel sisi run eege eegen eene deeg 6 COM 1 9 Pin SubD Outs Table ii 8 COM2 9 Pin SubD Outs Table 9 Product SpecificatiOnS sssnns 11 DIMENSIONS E 11 Cabling E 11 Environmental ciciciscss2inececericaussntienncesnvsedasseinmnteendsauepnannn knits sid
5. annsbodannatcnsseaxesnoonenncecieas 11 Options and Other Features sers 12 Ee E 13 Repair S ueei YY iTT UD RF YY E E E AR FNAFNUUDIAN AY FAR FYR 13 Not CoVered TTT 13 Out of Warranty Repairs ins ALLLL LLALL Y YLLLn LLY Hn nnr nLunnnnnn 13 Regulatory Noti S s nn sssnnssnsssersesentienstsssserenntasssns 14 FCC Advisory Statement 4 e iuui cr WYS Y ROLL YY WNA YRR ODD E RY YNN RR RD E YY nnne 14 Appendix A Enclosure Views 15 Appendix B User Manual Revisions 17 Contact NET siiscsaicccennscasacesientcewetaenssectiesansstcanceasticsdeostiescunsteestvesint 18 Rev 1 2 TS ENC560 3 Technologic Systems Inc Product Overview Introduction The TS ENC560 metal enclosure is made to house the TS 5600 Single Board Computer and two PC 104 peripheral boards The switching power regulator efficiently converts 12 38 VDC to regulated 5 VDC required by the SBC Features and Benefits 12 38 VDC input provides 5VDC to the SBC COM ports adapted to standard 9 pin Sub D PCMCIA slot in front panel Status LED s for Ethernet ports are visible Power Good LED visible at back panel Surge suppression on DC power input Sturdy metallic design reduces noise Dimensions 2 3 8 x 5 x 6 3 8 Related Products The TS ENC560 enclosure is designed for the TS 5600 Single Board Computer and two PC 104 peripheral boards Software and Support a Free system software and documentation updates
6. cordance with the specifications in Subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this eguipment in a residential area is likely to cause interference in which case the owner at his own expense will be reguired to correct the interference If this eguipment does cause interference which can be determined by turning the unit on and off the user is encouraged to try the following measures to correct the interference 1 Reorient the receiving antenna 2 Relocate the unit with respect to the receiver 3 Plug the unit into a different outlet so that the unit and receiver are on different branch circuits 4 Ensure that mounting screws and connector attachment screws are tightly secured 5 Ensure that good quality shielded and grounded cables are used for all data communications If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The following booklets prepared by the Federal Communications Commission FCC may also prove helpful a How to Identify and Resolve Radio TV Interference Problems Stock No 004 000 000345 4 A Interface Handbook Stock No 004 000 004505 7 These booklets may be purchased from the Superintendent of Documents U S Government Printing Office Washington DC 20402 TS ENC560 14 TS Enclosure 560 User Manual
7. it to Technologic Systems Inc at the address below Not Covered This limited warranty does not cover damages resulting from lighting or other power surges misuse abuse abnormal conditions of operation or attempts to alter or modify the function of the product Important l This warranty is limited to the repair or replacement of the defective unit In no event shall Technologic Systems be liable or responsible for any loss or damages including but not limited to any lost profits incidental or consequential damages loss of business or anticipatory profits arising from the use or inability to use this product Out of Warranty Repairs Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping Please contact Technologic Systems to arrange for any repair service and to obtain repair charge cost information 16525 East Laser Drive Fountain Hills AZ 85268 TEL 480 837 5200 FAX 480 837 5400 http www embeddedx86 com Rev 1 2 TS ENC560 13 Technologic Systems Inc Regulatory Notices FCC Advisory Statement Warning This eguipment generates uses and can radiate radio freguency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class A computing device in ac
8. tallation TS ENC560 10 Product Specifications Dimensions TS Enclosure 560 User Manual The TS Enclosure 560 measures 2 3 8 x 5 x 6 3 8 Cabling a A mating power connector is supplied with the enclosure a A null modem cable is available as CB7 05 Environmental To ensure optimum product operation you must maintain the operational environmental specifications listed in the table below Environmental Standard Temp Specifications Products Ambient Temperature 0 60 C The internal temperature must not exceed 70 C Relative Humidity Not to exceed 9096 noncondensing Rev 1 2 Extended Temp Products Allow for a much greater range Note Refer to your product manual or contact Customer Service at Technologic Systems if the environmental temperature of the location is in doubt Not to exceed 90 noncondensing TS ENC560 11 Technologic Systems Inc Options and Other Features a RS 485 is optional on COM1 a A wall mounted power supply is available for this product TS ENC560 12 TS Enclosure 560 User Manual Limited Warranty Technologic Systems warrants this product to be free of defects in material and workmanship for a period of one year from date of purchase Repairs During this warranty period Technologic Systems will repair or replace the defective unit in accordance with the following process A copy of the original invoice must be included when returning the defective un
9. ted for RS 232 communications See the table below for RS 485 operation COM1 9 Pin SubD Outs Table Half Duplex RS 485 RS 232 Full Duplex RS 485 AL Signal SNE Signal Se Signal 1 RX TX 1 1 TX 2 2 Receive data 2 3 3 Transmit data 3 4 4 4 RX 5 Ground 5 Ground 5 Ground 6 RX TX 6 6 TX 7 7 Request to Send 7 8 8 Clear to Send 8 9 9 9 RX TS ENC560 8 TS Enclosure 560 User Manual Enclosure TS ENC560 COM2 Port Pin 1 highlighted a COM 2 COM2 is brought in from the base SBC This 9 pin SubD connector is industry standard for a PC The TxD RxD RTS CTS and ground pins are supported for RS 232 communications COM2 9 Pin SubD Outs Table RS 232 EE Signal 1 Carrier Detect 2 Receive Data 3 Transmit Data Data Terminal 4 Ready 5 Ground 6 Data Set Ready 7 Request To Send 8 Clear To Send 9 N C Rev 1 2 TS ENC560 9 Technologic Systems Inc Enclosure TS ENC560 12 38 VDC Connector a 12 38VDC The three pin connector accepts 12 38 VDC of external power to supply power to the board Power Indicator Light a Power Indicator Light The amber colored LED indicator on the rear panel shown highlighted above in red is the power LED It is lit whenever power is applied to the unit Chassis Grounding Lug a Chassis Grounding Lug The lug labeled with the chassis ground symbol is used to ground the chassis optional Note A Connect this to earth ground during ins
Download Pdf Manuals
Related Search