INSTALLATION GUIDE & USER`S MANUAL
Contents
1. VENTING METHODS VENTING REQUIREMENT IMPORTANT NEVER exhaust air or terminate duct work into spaces between walls crawl spaces ceiling attics or garages All exhaust must be ducted to the outside Hood mounted too low could result in heat damage and fire hazard while hoods mounted too high will be hard to reach and will loose its performance and efficiency Use metal duct work only Rigid metal vent is recommended minimum of 6 round standard for this range hood purchased separately must be used to maintain maximum airflow efficiency DO NOT use plastic vent DO NOT use 4 10 2 cm laundry type wall caps Fasten all connections with sheet metal screws and tape all joints with aluminum tape Use caulking to seal exterior wall or roof opening around the cap The vent system must have a damper If roof or wall cap has a damper do not use damper supplied for some models only with the range hood For the most efficient amp quiet operation A distance of 26 to 30 1s recommended between stove top and the bottom of range hood It is recommended that the range hood be vented vertically through the roof through 6 or bigger vent work ALWAYS when possible reduce the number or transitions and turns If long duct run 1 required increase duct size from 6 to 7 or 8 Ifa reducer is used install a long reducer instead2. The Advanced Range Hoods INSTALLATION GUIDE amp USER S MANUAL PRO X SERIES Wall Mount Range Hood Models PX01 W30 PX01 W36 PX02 W30 PX02 W36 PX03 W30 PX03 W36 PX04 W30 PX04 W36 PX04 W42 PX06 W30 PX06 W36 PX06 W42 lb LISTED Intertek IMPORTANT READ AND SAVE THESE INSTRUCTIONS FOR RESIDENTIAL amp INDOOR USE ONLY www 5 1 TABLE CONTENTS 1 IMPORTANT SAFETY INSTRUCTIONS ul u URS UR SU MUSS 2 3 2 HEIGHT amp CLEARANCE REQUIREMENT 4 3 VENTING REQUIREMEN PEE 4 4 VENTING METHODS 4 5 ELECTRICAL REQUIRENIENT i 5 6 TOOL YOU WILL NEED uu u RE 5 7 PARTSUPPLIBD 6155 2 DIE SUI E SE aa 5 8 RANGE HOOD DIMENSIONS amp INSTALLATION OVERVIEW 6 9 INSTALLATION 7 9 10 RANGE HOOD OPERA LION Ea dE 10 12 11 wig amp ULT W uuu uuu M 12 12 TROUBLE SHOOTING 5545555 13 13 REPLACING THE LIGHT BULB
3. 13 14 USE amp CARDS 14 IMPORTANT SAFETY INSTRUCTIONS IMPORTANT NOTICE The Important Safety Instructions and warnings in this manual are not meant to cover all possible problems and situations that might occur Please also use common sense and caution when installing maintaining or operating this or any other appliances Please always contact the XtremeAir USA LLC Customer Support Team at 1 714 554 9000 or email support XtremeAirUsa com with any problems or situations that you do not understand or confuse The manufacturer disclaims all liability for any damage or injury caused as a result of not following instructions for installation contained in the following text SS n c c d e et SS i c i SS sc 1 A DANGER om a a a yU a a i To avoid the possibility of explosion or fire do not store or use combustible flammable or explosive vapors and liquids such as gasoline inside or in the vicinity of this or any other appliance Keep items that could explode such as aerosol cans away from cook top burners ovens and range hoods Do not store flammable or explosive materials in adjacent cabi
4. CHIMNEY WIDTH x HEIGHT 15 dimension from cook top to bottom of range 3 MOUNTING SCREWS hood vary 26 to 30 plus from bottom x of range hood to mounting bracket hole STEP 3 prepare ductwork amp single outlet skip this step if already there 1 Have 15amp 120V 60Hz single outlet anywhere inside x the chimney width lines make sure at least 2 inches below ceiling line for ceiling bracket mount 2 Have 6 Inches diameter ductwork hanging down from x ceiling to the mark of mounting screws 2 inches away from wall is recommended since you need room for plug in and out x STEP 4 install ceiling bracket mounting anchors and screws x 1 Place center of upper chimney bracket inline with centerline and all the way up to ceiling then screw it to x 1 the wall 2 Pre drill holes where your mounting marks are then insert wall anchors and mounting screws make sure leaving 1 8 space away from the wall 21 A us MOUNTING SCREW WWW XtremeA1rUsa com PAGE 7 STEP 5 Hang the hood and connect 1 Carefully hang the hood body on the wall attaching it to the 2 screws already in place 2 Level the hood body by using horizontal level 3 Use hand screw driver to tighten those 2 mounting screws 4 Connect the exhaust on the hood to the ductwork above Use aluminum tape to make all joints secure and all tight 5 Find three pronged plug and conn
5. of a pancake reducer Reducing duct size will restrict airflow and decrease airflow thus reduce duct size as far away from opening as possible If turns or transitions are required Install as far away from opening and as far apart between 2 as possible The size of the vent should be uniform Use no more than three 90 elbows Make sure there is a minimum of 24 61 cm of straight vent between the elbows if more than one elbow 15 used DO NOT install two elbows together Horizontal wall venting Vertical roof venting Option 1 Optlon 2 WWNW XtremeA1rUsa com PAGE 4 ELECTRICAL REQUIREMENTS IMPORTANT Observe all governing building codes and ctty ordinances m 120 volt 60 Hz AC only 15 amp fused electrical circuit 1s required It is the customer s responsibility contact a qualified electrical installer e assure that the electrical installation is adequate and in conformance with National Electrical Code ANSI 70 latest edition or CSA Standards C22 1 94 Canadian Electrical Code Part 1 and C22 2 No 0 M91 latest edition and all local codes and ordinances 06 TOOL YOU WILL NEED Maker or pencil a Stud finder Measuring tape Powered screwdriver or drill Flat amp Phillips screwdrivers Box level Drill with 1 8 drill bit Jigsaw or keyhole saw Cabinet Jack optional PARTS SUPPLIED 1 Inside Chimney 2 or 3 Baffle Filters 6 An
6. several times NEVER cook on open flames under the range hood Check deep fryers during use Superheated oil may be flammable Cleaning The saturation of greasy residue in the blower and filters may cause increased inflammability Keep unit clean and free of grease and residue build up at all times to prevent possible fires FILTERS MUST BE CLEANED PERIODICALLY AND FREE FROM ACCUMULATION OF COOKING RESIDUE Old and worn filters must be replaced immediately DO NOT operate blowers when filters are removed Never disassemble parts to clean without proper instruc tions Disassembly is recommended to be performed by qualified personnel only Read and understand all instructions and warnings in this manual before proceeding MAINTENANCE SAFETY WARNING Never put your hand into area housing the fan while the fan 15 operating For optimal operation clean range hood and all baffle spacer filter grease tunnel oil container regularly Regular care will help preserve the appearance of the range hood Cleaning Exterior surfaces Clean periodically with hot soapy water and clean cotton cloth Do not use corrosive or abrasive detergent e g Comet Power Scrub EZ Off amp oven cleaner or steel wool scoring pads which will scratch and damage the stainless steel surface For heavier soil use liquid degrease such as Formula 409 or Fantastic brand cleaner If hood looks splotchy stainless steel hood use a stainless steel cleaner
7. to clean the surface of the hood Avoid getting cleaning solution onto or into the control panel Follow directions of the stainless steel cleaner CAUTION Do not leave on too long as this may cause damage to hood finish Use soft towel to wipe off the cleaning solution gently rub off any stubborn spots Use dry soft towel to dry the hood After cleaning you may use non abrasive stainless steel polish such as or ZEP to polish and buff out the stainless luster and grain Always scrub lightly with clean cotton cloth and with the grain DO NOT allows deposits to accumulate or remain on the hood DO NOT use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface and cause rusting DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods Many of these compounds contain chemicals which may be harmful Rinse with water after exposure and wipe dry with a clean cloth Cleaning Aluminum Grease Filter Stainless Steel Filter less Grill IMPORTANT Drain oil from oil containers before oil and residue overflow The metal filters fitted by the factory are intended to filter out residue and grease from cooking It need not be replaced on a regular basis but are required to be kept clean Filters should be cleaned after every 30 hours of use Remove and clean by hand or dishwasher Spray Formula 409 or equivalent degreasing deter
8. 12 TROUBLE SHOOTING 1 If the range hood or lights does not operate after installation e Check if the range hood has been plugged in make sure that all power has been turned back ON the fuse 15 not blown and all electrical wiring 15 properly connected Swap out light assembly to working ones to detere mine whether it is caused by defective bulbs See replacing the light bulbs on Page 13 2 The range hood vibrates when the blower is on The range hood might not have been secured properly on to the ceiling or wall Check if the motor is secured in place If not then tighten the motor in place Check if the blower wheel is damaged 3 The blower or fan seems weak e Check that the duct sized used is at least 6 Range hood WILL NOT function efficiently with insufficient duct size amp loosely secured e Check if duct is clogged or if damper unit half circular flapper is not installed correctly or opening properly A tight mesh on a side wall cap unit might also cause restriction to the air flow 4 The lights work but the blower is not spinning at all is stuck or is rattling The blower might be jammed or scraping the bottom due to shipping damage Please contact us immediately e The motor is defective possibly seized change the motor 5 The hood is not venting out properly Make sure the distance between the stove top and the bottom of the hood 15 within 26 and 30 in distance Due to different ceiling height configu
9. chors Aluminum Pipe check w your local code for approval 1 Oil tunnel except for PX04 1 Remote control PX02 model only 1 Outside Chimney WWW XtremeA1rUsa com PAGE 5 08 HOOD DIMENSIONS amp INSTALLATION OVERVIEW 9 3 Z 105 PX02 W30 PX02 W36 PX01 W30 PX01 W36 Installation Overview 55 PX04 W30 PX06 W30 04 36 PX06 W36 WWW XtremeA1rUsa com PAGE 6 INSTALLATION wasa q STEP 1 OPTIONAL ONLY Protect cook top amp create work station Have 2 pieces 2 x 4 x 20 on both sides of stove and plywood on top of them to protect cook top or stove from damage or dirt This plywood will also create a comfortable work station for easy to installing 4 STEP 2 Marking on the wall CEILING 1 Center 15 center of cook top stove 2 Chimney width is the width of the chimney Varies in each model 3 Mounting screws where the hood body will be hanging from FOR PX02 MODELS please assemble mounting bracket to hood body first so you can find exact dimension MOUNT SCREW HOLE DIMENSIONS a e WIDTH 15 dimension from center to center of mounting 1 CENTER LINE bracket hole 2
10. conds when the range hood is first electrically activated Self calibration will be set when the range hood beeps LCD panel will turn off automatically after a period of inactivity A Activating Normal Blower Function o o While the range hood is off Touch to start from lowest speed Touch to start from Highest speed F4 00 blower off F quiet speed F2 low speed Touch or again to change the blower speed as indicated in LCD panel medium speed F4 high speed Decrease Increase D Acuvauny Light Function Touch Light button to turn the lights on or off Light C Activating Power Off Delay Function 1 While the range hood 1 on and the blower is running in normal mode touch Power Off Delay button to activate delay off timer 2 Adjust to desired period of delay of timer by touching or button quickly 1 15 minutes Power Off Timer begins to countdown immediately when it reaches 0 the blower will shut off 3 Display screen will show flashing clock if timer is working WWW XtremeA1rUsa com PAGE 10 Activatine Smoke Detector Function While the machine 1 off touch Auto Function button to activate the smoke detector auto function mode NOTE this function will only worked when there s lot of smoke Once this button is touched all Auto Function other buttons are not active E Changing the clock While the blower 15 off 1 Touch power
11. des STEP 8 install oil tunnel Coy Figure 2 OIL TUNNEL SIDE VIEW Drop oil tunnel into recess support near rear of hood Note PX04 amp PX06 skip this step STEP 9 install baffle filters 1 Angle baffle filter toward back of hood 2 Lift a baffle filter up above horizontal level then slide forward into slot behind the front of hood To remove the baffle please reverse the process WWW XtremeA1rUsa com PAGE 9 RANGE HOOD OPERATION BEFORE YOU BEGIN important this machine 15 equipped with TOUCH SENSITIVE CONTROL so please 1 DO NOT PRESS Only TOUCH amp HOLD DOWN 2 SECONDS for every change makes 2 TOUCH A WHOLE BUTTON only please see below picture wrong vs right WRONG RIGHT VS RIGHT a whole button 1s covered by a finger WRONG Only half of a button is covered by a finger NOTE For best results start the range hood before cooking and allow it to operate several minutes after the cooking is completed to clear all smoke and odors from the kitchen 1 TYPE 1 TOUCH SCREEN CONTROL FOR PX02 models ONLY Light Indicator Power Off Delay Blower Indicator Auto Function Indic ator Tadic ator O 7 o o Decrease Power Off Increase Delay Remote Control TYPE 1 TOUCH SCREEN CONTROL Auto Function Note This range hood is equipped with remote control and smoke sensor that will self calibrate within 5 se
12. ect to an electrical outlet CAUTION Do not release the hood yet until you finish Step 6 below STEP 6 Secure the hood body amp test run 1 Use stud finder to find all studs below the hood body then put the blue tape on every stud found 2 use 1 8 drill bit to drill though the back of hood inline with blue tape 3 Secure the hood body by using about 1 5 inches long wood screws not provided through the back of hood to the stud 4 Referto page 7 range hood operation try a few test runs to ensure machine is running properly STEP 6A for 01 MODEL ONLY install glass canopy 1 Loosen the four canopy screws and washers from the hood top 2 Carefully place the canopy glass on the hood top then slightly tighten the four canopy screws along with washers DO put excessive pressure against the glass WWW XtremeA1rUsa com PAGE 8 STEP 7 Install chimney x 1 Take off outsider chimney protective laminate coating not the inner chimney 2 Place both chimneys on top of range hood base 3 Make sure the chimney is facing the correct direction PX02 outside chimney screw hole on the bottom Inside chimney screw hole on the top PX0I PX03 inside chimney screw hole the top 4 Secure outside chimney to the base of the hood PX02 ONLY 5 Attach the inside chimney to the ceiling mounting bracket 6 Screw the chimney into place on both si
13. gent and leave to soak if heavily soiled Dry filters and re install before using hood WWW XtremeA1rUsa com PAGE 14
14. iling do not damage electrical wiring and other utilities Due to the size and weight of this range hood two people installation Is recommended Range hood may have very sharp edges please wear protective gloves if it is necessary to remove any parts for installing cleaning or servicing VENTTING For kitchen range or cook top ventilating use only DO NOT use to exhaust hazardous or explosive materials and vapors Ducted fans MUST always be vented to the outdoors DO NOT vent exhaust into spaces between walls crawl spaces ceiling attics or garages Use only metal ductwork Old duct work should be cleaned or replaced if necessary to avoid the possibility of a grease fire Check all joints on duct work to insure proper connection and all joints should be properly taped ELECTRICAL electrical wiring must be properly installed insulated and grounded Before servicing or cleaning unit turn power OFF and un plugged OPERATION Use high settings on cooking range only when necessary Keep all fan baffle spaces filter grease tunnel oil container and grease laden surfaces clean Grease should not be allowed to accumulate on fan baffle spaces filter grease tunnel and oil container Never allow the filters to become blocked or clogged Do not allow foreign objects such as cigarettes or napkins to be sucked into the hood WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE m Never leave surface units unattended at high settings Boil ove
15. ions 1 1 To power ON OFF and to activate power off delay timer 2 To decrease blower motor speed decrease timer value and enter timer mode 7 To increase blower motor speed increase timer value and cumulative timer reset 3 Blower motor is running light indicator 4 Shows current blower motor speed 1 4 5 Lights up when lights turned on 6 To turns ON OFF lights 8 Indicates the accumulated time the system is running 9 Indicates the length of time left for delay off function 10 10 Lights up when auto shutdown delay timer function 1 on A Activating Blower Function Option 1 Touch and hold down for 1 2 seconds Option 2 Touch and hold down power sign 1 for 1 2 seconds the blower will be running at the same speed as last used Note The system saves user configurations settings such as timer and blower motor speed will remain the same the next time it is turned on www XtremeAirUsa com PAGE 11 oS Adjusting blower speed Touch and hold down for increase Touch and hold down for decrease C Turning off the blower Touch and hold down power sign 1 for 1 2 seconds D To turn the light ON OFF Touch Light button once to turn on the lights and once again to turn off the lights E Adjusting the timer function 1 While the blower motor 1 not running touch and hold Decrease Value button over 3 seconds to enter timer mode 2 Adjust to desi
16. nets or surrounding areas Disclaimer 7he manufacturer and or distributor reseller decline all responsibility in the event of failure to ob serve the instructions provided for installation maintenance and suitable use of the product The manufacturer and or distributor reseller shall NOT be responsible for any injury due to negligence and the warranty of the unit shall automatically be voided due to failure to observe proper safety and installation procedures The manufacturer and or distributor reseller will not be held responsible for any damages to personal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood WWW XtremeA1rUsa com PAGE 2 IMPORTANT SAFETY INSTRUCTIONS continue WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING Use this unit only in the manner intended by the manufacturer If you have questions contact the manufacturer PRODUCT Do not remove permanently affixed labels warnings or plates from the product This may void the warranty Do not try to alter the hood INSTALLATION The installation in this manual 1s intended for qualified installers service technicians or persons with similar qualified background Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards including fire rated construction When cutting or drilling into wall or ce
17. rations recommended height may not be applicable e Reduce the number of elbows and length of duct work Check if all joints are properly connected sealed and taped e Make sure the power is on high speed for heavy cooking 6 The hood is noiser than normal The duct is not secure and causes vibration The smaller duct size than required Is usED 7 Control panel is not active e Check to make sure the auto function is not on 8 Remote control is not working e Check to make sure the plastic film was removed 13 REPLACING THE LIGHT BULB 1 Make sure the range hood is unplugged or turn OFF breaker 2 Use the small flat screw driver to lift any where around the outside ring as show in picture 3 Install new light bulb 4 Put back the light set by pressing it in 5 Turn ON breaker and range hood to test for operation WWW XtremeA1rUsa com PAGE 13 USE amp CARE INFORMATION Operations Read and understand all instructions and warnings in this manual before operating the appliance Save these instructions for future reference Always leave safety grills and filters in place Without these components operating blowers could catch on to hair fingers and loose clothing NEVER dispose of cigarette ashes ignitable substances or any foreign objects into blowers NEVER leave cooking unattended When frying oil in the pan can easily overheat and catch fire The risk of self combustion is higher when the oil has been used
18. red period of delay off timer by touching Increase Value or Decrease Value button minimum 1 minute to maximum 15 minutes This setting will be saved immediately F Activating the timer function While the blower motor is running touch and hold Power button for over 3 seconds to activate delay off timer Power off delay indicator will light up and power off delay digital timer will begin to countdown when it reaches zero the blower motor will shut down G To clear cleaning reminder e When blower motor starts to rotate cumulative running time will be shown in Power On Elapsed Digital Timer This timer icon flashes when 30 hours is up and reminds user to clean the baffle filters e After cleaning the filters and when the motor is not in use touch and hold Increase Value button over 3 seconds to reset the timer Please note that turning off the system will not reset the Power On Elapsed Digital Timer F AUTOMATIC SHUT OFF e MACHINE WILL AUTOMATICLY SHUT OFF AFTER APPROX 2 HOURS FOR THOSE MANUFACTURED AFTER AUGUST 2012 ONLY SPECIFICATION Body Design Seamless Stainless Steel Satin Finish 120V 60Hz USA amp Canada standard General Input Power 154W 150W 2x2W One Motor S Number Of Motors One Motor Motor Type Single Chamber Ultra Quiet Top 6 inches Round Interference Protection Radio Frequency Interference Protected Specification subject to change without notice www XtremeAirUsa com PAGE 12
19. rs cause smoking and greasy spillovers that may ignite Heat oils slowly on low or medium settings m Always turn hood ON when cooking at high heat or when greasy food m Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter m Use proper pan size Always use cookware appropriate for the size of the surface element WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE OBSERVE THE FOLLOWING SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner Be careful to prevent burns If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT m NEVER PICK UP A FLAMING you may be burned DO NOT USE WATER including wet dishcloths or towels a violent steam explosion will result m Use an extinguisher ONLY if You know you have a class ABC extinguisher and you already know how to operate it The fire 15 small and contained in the area where it started The fire department is being called You can fight the fire with your back to an exit www XtremeAirUsa com PAGE 3 02 HEIGHT amp CLEARANCE f Min 26 30 36 hase
20. sign once the hour indicator will flashing 2 use to adjust to designed hour 3 Touch power sign again the minutes indicator will flashing 4 use or to adjust to designed minutes 5 Touch power sign again to clear the screen Touch light button to validate To check time touch light button Note The clock display is only available for product manufactured after October 2012 E Remote Control Sensor Remote control sensor receives infrared IR signal from the remote control The maximum distance for IR data transmission 15 3 meter and requires direct line of sight The transmission distance may vary depending on temperature and remote control battery condition Light settings are independent from other settings including power off delay and lights have to be manually turned on or off The system saves user configurations settings such as light timer and blower motor speed will remain the same the next time it is turned on C j Be 1 Power Light 2 Decrease Value Increase Value 3 Blower Power Indicator Power On Elapsed Digital Timer 8 4 Blower Speed Indicator Power Off Delay Digital Timer Light Power Indicator Power Off Delay Timer Indicator TYPE 2 TOUCH BUTTON CONTROL NOTE For best results start the range hood before cooking and allow it to operate several minutes after the cooking is completed to clear all smoke and odors from the kitchen Button funct
Download Pdf Manuals
Related Search