Home

User Manual

1. Pairing button Power supply connection HN f ATA 5 V DC 1 A Cm E a A E E E n Y 4 5 Cable connections fo Yellow RCA plug video Connection for transmitting the video signal White RCA plug audio Connection for transmitting the audio signal Jack plug Plug for connecting to the monitor To connect the video RCA plug to a BNC input on a monitor or recorder attach the BNC RCA adapter to the yellow RCA plug 29 5 Installation 5 1 Pairing the camera and monitor To connect a camera with the monitor proceed as follows 1 2 4 Connect the power supply to the cameras and monitor In the TFT monitor s menu Camera Setup gt Pairing select the camera you require 1 4 and confirm your choice with OK The systems starts a 60 second countdown During the 60 seconds press the PAIRING button on the camera cable until the green LINK LED on the front of the camera starts to flash Bei erfolgreicher Verbindung leuchtet die LINK LED der Kamera dauerhaft A Warning Please note that connection can take up to 60 seconds 5 2 Installing the camera Select a suitable place for installing the camera using the camera mount Mark the drill holes on the base and pre drill them Insert the wall plugs provided and attach the mount with the screws Warning Before you start with the installation make sure that the wireless transmission range reaches your desired installation location You
2. 4 Device description 4 1 Front of the monitor Y 9 LAH H A C Displays the current charge level Red Battery low Green Charging Off Battery completely charged Device status display Power LED Blue Device switched on Off Device switched off V Battery display O Live view channel change CH In the menu switch between menu items lt Live view increase volume ol Inthe menu switch between menu items 6 gt Live view reduce volume Vol Inthe menu switch between menu items CH Live view channel change Y Inthe menu switch between menu items Live view open the events list ude Inthe menu confirm the settings and changes Live view Start stop recording Rec Del Inthe menu delete the recording Only possible with SD card Live view open exit the menu Inthe menu exit submenu Menu ESC The system automatically exits the menu after a wait time of one minute 2 Antenna ooo 4 2 Rear of the monitor 300000000000 4 3 Monitor connections Power supply 5 V DC 1 A DC 14 5 x 4 8 mm AV output Output for representing the on screen display use the AV cable supplied SD card slot Slot for using an SD card of up to 32 GB Switch monitor on or off 28 Ye Q 4 4 Camera description Omena Lightsens Fixediens PowerlED UNKLED IRLED PIRsensor Il 7
3. SD Card Format format SD card Power Saving energy saving mode TV Format TV output resolution Set to factory Default reset to factory defaults System Version software version of the monitor and camera Camera on off show hide camera Use the gt buttons to select a camera Press Camera On Off Camera Brightness OK to switch between ON and OFF If you switch the camera OFF it is no longer shown Use the lt b buttons to select the desired camera and confirm your choice with OK The relevant camera image is shown with a selection bar with the options 0 9 You can use the lt P buttons to change the setting and confirm with OK 34 Pairing add camera Pairing Resolution 6 4 Record settings Alarm Period length of alarm when motion is detected Alarm Period Motion Detection recording duration for motion detection Motion Detection Record Period 35 Use the lt gt buttons to select the desired camera and confirm your choice with OK The systems starts a 60 second countdown During the 60 seconds press the PAIRING button on the camera cable until the green LINK LED on the front of the camera starts to flash Once the connection is successful the LINK LED on the camera lights up continuously and the monitor switches to live view Use the gt buttons to select between the resolutions 640 x 480 and 320 x 240 Confirm your input with OK Note that the recording time changes for
4. e aa eaa Ea A aE A AE E 39 Eaa eR e 1 T AA T A N E A E NE A A E A A A 40 25 You can use this 2 4 GHz wireless monitor and the IR wireless outdoor camera with PIR for easy wireless transmission and displaying of video signals across middle to long distances Wireless signal transmission is an advantage in all locations where cables cannot be laid the camera transmits the video signal to the wireless monitor without the need for wires Faults and interference can be avoided due to the conversion into digital signals As soon as the camera s PIR sensor detects movement it starts recording to the SD card You have the option of connecting up to 4 cameras TVCC40005 to the monitor and showing then in a quadruple display 1 Intended Use A detailed function description can be found in chapter 3 Description and functions 2 Scope of delivery 1 x IR wireless external 2 4 GHz camera 3 5 TFT monitor including camera mount and installation material d 2 GB 2 x power supply units including EU 2 GB SD card AU and UK adapters 5 V DC 1 A wi T eee nm 1 eee AV cable 1 x antenna 3 Features and functions e Complete set consists of 3 5 TFT monitor and IR wireless outdoor camera 2 4 GHz e Compact IP66 outdoor camera with infrared night vision function and 400 TVL resolution e 3 5 colour TFT with integrated loudspeaker e Digital encrypted audio and video transmission e User friendly OSD on screen display 26
5. now have the option of swivelling the mount by 90 to position it where you want it Loosen the screw at the side and set the angle of view required Then tighten the screw in the required position to fasten 30 Then screw the camera onto the mount and the power supply unit with the camera Jilid diddi A Warning Only use the antenna provided for the installation 5 3 Installing the monitor The installed battery gives you the option of using the TFT monitor flexibly When the battery LED lights up red the battery needs charging Make sure that the battery is always sufficiently charged in order to guarantee no loss of recording Warning Note that the monitor has to be charged for at least 8 hours before it is used without an external power supply for the first time The battery life is about 3 5 hours To do this unfold the stand and position the monitor on the desired location 31 To display the monitor display on another device proceed as follows 1 Connect the jack plug to the monitor s AV OUT 2 Connect the RCA plug to the monitor as shown in the drawing 6 Operation To switch the monitor ON OFF press and hold the power button for at least 2 seconds Each time it is started the monitor switches to live view and it selects the last view that was set If the El icon is displayed the monitor has correctly identified the SD card and it is working normally 6 1 Liv
6. the different resolutions Use the gt buttons to select the desired alarm duration You can choose between OFF 5 sec 10 sec 15 sec Confirm your selection with OK The alarm duration is set to 5 seconds by default Press any button to switch off the alarm when it sounds Use the lt gt buttons to select the recording duration for motion detection You can choose between OFF 5 sec 10 sec 15 Sec Confirm your input with OK The recording duration is set to 5 seconds by default Motion detection is deactivated for 5 seconds after an alarm SD Card Overwrite SD card circular buffer SD Card Overwrite 6 5 Event list Event List event list Delete Delete 36 Use the lt gt buttons to activate ON or deactivate OFF the SD card circular buffer Confirm your selection with OK The circular buffer is activated by default Warning When the memory capacity is reached the monitor continues to record deleting the oldest recordings on the SD card The SD card capacity display flashes with 0 0 G in red Use the arrow buttons to navigate between folders Press the OK button to select the desired folder In the sub folder choose the relevant recording file and play it by pressing OK Press A or Y to fast forward or rewind at the speeds 2x 4x 8x 16x Note that the maximum recording time for a manual recording is 10 minutes Once this time elapses a new file is created Press DEL to en
7. to dust the product Accessories Do not use any unsupported accessories as these may be hazardous or cause damage the product Location e This device can be used in inside as well as outside e The product will be damaged even it falls from a low height e During the installation of the camera please take care that direct sunlight cannot fall onto the image sensor of the device Please follow the installation instructions in the corresponding chapter of this user manual e Do not place the device near a radiator or heat register e Setup the device only in areas with the advised operating temperatures of 10 50 C 23 7 Wireless transmission The range of wireless transmission depends on various environmental factors The local conditions at the installation location can have a negative impact on the range For this reason if there is a clear line of sight between the receiver and the transmitter the range can be as much as 200 m but in buildings it is significantly less The following environmental factors impair both the range and the frame rate Mobile phone masts high tension electricity pylons power lines ceiling and walls devices with the same or similar radio frequency Warnings Follow all safety and operating advises before starting up the device 1 Follow these directions in order to avoid damage of the power cord or plug e Do not modify or process the power cord or plug arbitrarily e Make sure to disconnec
8. Security Tech Germany TVAC15000 User manual Version 03 2012 Original English user manual Keep for future use Introduction Dear Customer Thank you for purchasing this product This product meets the requirements of the applicable European and national guidelines The corresponding declarations and documents can be obtained from the manufacturer www abus sc com To maintain this condition and to ensure risk free operation you as the user must observe these operation instructions Before initial start up read through the complete operating instructions observing operating and safety instructions All company and product names mentioned in this document are registered trademarks All rights reserved If you have any questions please contact your installer or your local dealer A Disclaimer This user manual was prepared with greatest care If you should notice omissions or inaccuracies please inform us about these on the back of this manual given address The ABUS Security Center GmbH assumes no liability for technical and typographical faults and reserves the right to make at any time modifications to the product or user manual without a previous announcement The company is not liable or responsible for direct and indirect subsequent damages which are caused in connection with the equipment the performance and the use of this product No guarantee for the content of this document is taken Icon expl
9. Use the A Y buttons to change the values Confirm your input with OK SD Card Format format SD card You can use this to format the SD card The system displays the memory that is currently available Free and the total memory Total Press OK to start formatting Confirm your selection with and cancel the operation with SD Card Format Warning Format the SD card before using it for the first time Use the lt P buttons to switch the energy saving mode ON or OFF This function is activated by default This function switches the screen to standby mode after two minutes The loudspeakers continue to operate at the same volume Press any button to exit energy saving mode Power Saving Use the lt P buttons to select the desired TV format You can choose between NTSC and PAL Confirm your input with OK Note that the format selected can affect the resolution TV Format Set to Factory Default reset to factory defaults Press OK to start the factory settings Confirm your selection with and cancel the operation with amp Please note Note that this operation does not format the Set to Factory Default SD card 38 System Version This function shows you the software versions of software version of the monitor and camera the monitor and all the connected cameras System Version IW Sp Snare Carll VERSINI Cais Weis dalle Cams Vers Qh 6 Camd Ver ymn 7 Maintenance and cleaning 7 1 Mainte
10. anation a A flash in the triangle is used if there is danger for the health e g by an electric shock A An exclamation mark in the triangle points to an important note in this user manual which must be minded a This symbol can be found when you are to be given tips and information on operation Important safety advice The warranty will expire for damage due to non compliance with these operating instructions ABUS will not be liable for any consequential loss ABUS will not accept liability for damage to property or personal injury caused by incorrect handling or non compliance with the safety instructions In such cases the warranty will expire The device has been manufactured in compliance with international safety standards Please read these safety advices carefully Safety advice 1 Power supply 100 240 V AC 50 60 Hz via power adapter plug to 5 V DC Operate this product only from the type of power supply indicated on the marking label If you are not sure of the type of power supplied to your home consult your local power company Disconnect the product from the mains before you start any maintenance or installation procedures Overloading Do not overload a wall outlet extension cord or adapter as this may result in electric fire or shock Liquids Protect the device from any kind of liquids entering Cleaning Disconnect the product from the wall outlet before cleaning Use a light damp cloth no solvents
11. e unfavourable the range may be very restricted 40
12. e view Tull 2 rec e Id spl 0 86 4 NO SIGNAL 01 12 45 2011 05 01 14 30 11 Tull Channel display Recording display flashes during recording ls Motion detection recording activated 32 Motion detection alarm activated D No SD card inserted Full SD SD card full Err SD SD card was not identified S SD card locked SD card is overwritten when it reaches capacity Power supply display Camera brightness display 01 12 45 Recording time 2011 05 01 14 30 11 Date time display Please note The icons disappear automatically after being displayed for ten seconds 6 2 Main menu Press MENU to open the main menu You can use the arrow buttons to switch between menu items You can choose between the following Camera Setup Camera Setup Camera on off show hide camera Camera Brightness brightness of camera Pairing add camera Resolution image resolution Recorder Satin Recorder Setup Alarm Period length of alarm when motion is detected Motion Detection motion detection SD Card Overwrite SD card circular buffer 33 Event List System Setup 6 3 Camera settings Event list The recordings are stored in sub folders named after the recording date The recordings are stored as individual files with the time of recording as the file name System setup Quad Display four way display Scan Period dwell time for sequence display Time setting Date time settings
13. nance Regularly check the product s physical state e g check for damage of the housing If you suspect that safe operation cannot be guaranteed anymore disconnect the product and ensure that it cannot be used by mistake You can assume that safe operation is not possible anymore when e the device shows visible damage e the device does not function anymore Please note The product is maintenance free for you Inside the product are no parts that can be checked or repaired so do not ever open it 7 2 Cleaning Wipe the product with a clean dry cloth If the device is very dirty you can moisten the cloth with lukewarm water Make sure that no liquids can enter the equipment as the device can be destroyed Never use chemical detergents as they could attack the surface of the device 8 Disposal Devices with this marking should not be put in the household garbage Dispose of the product at the end of its lifetime according to the applicable regulations 39 9 Technical data TVAC15000 56 H 43 V 60 H 50 V IP protection class J IPOH T Weight 320 g Model number TVAC15000 3 5 TFT monitor re eee 4 640 x 480 pixels VGA 320 x 240 pixels QVGA 1 0 V p p 75 Ohm Li ion polymer battery Audio signal 1 0 V p p 600 Ohm The range depends on the ambient conditions e g mobile phone masts high tension electricity pylons power lines ceiling and walls etc If the conditions ar
14. t the power cord holding the plug e Keep heating appliances as far as possible from the power cord in order to prevent the cover vinyl from melting e The outdoor camera s power supply unit must be protected against humidity and damp 2 Follow these directions Failure to follow any of them may cause electrical shock e Do not open the main body or the power supply e Do not insert metal or inflammable objects inside the product e In order to avoid any damage during lighting use a surge protection 3 Do not use the product when it is out of order If you continue to use the product when defective serious damage can be caused to it Make sure to contact your local product distributor if the product is out of order During the installation into an existing video surveillance system make sure that all devices are disconnected from the low and supply voltage circuit If in doubt allow a professional electrician to mount install and wire up your device Improper electrical connection to the mains does not only represent at threat to you but also to other persons Wire up the entire system making sure that the mains and low voltage circuit remain separated and cannot come into contact with each other in normal use or due to any malfunctioning Avoid using the device under the following unfavorable ambient conditions e wetness or excessive air humidity e extreme cold or heat e direct sunlight e dust or combustible gases vapors or sol
15. ter deletion mode The current file or folder flashes You can use the lt b buttons to select all or one file Press OK to confirm your choice Select to delete the selection To cancel the deletion select 6 6 System settings Quad Display four way display Quad Display Scan Period dwell time for sequence display Scan Period System Clock Year Month Day Hours Minutes 3 Use the lt gt buttons to switch the quad display on ON or off To activate quad mode all the cameras have to be activated When in quad display you can use the arrow buttons to switch directly to full screen view for individual cameras A camera Y camera2 lt cameras gt camera4 Note that the cameras that are hidden are not shown in the quad display Warning Only the full screen of the triggering channel is recorded To record from all 4 cameras using motion detection quad display has to be activated You can define the dwell time for sequence display here Use the lt gt buttons to choose between OFF 5 sec 10 sec 15 sec If you are not using cameras hide them in order to display only the occupied channel To switch off sequence display press the CH CH button If you want to start manual recording press REC Warning Note that motion detection is only activated for the channel that is currently displayed Press the gt button to switch between year month day hours minutes
16. vents e strong vibration e strong magnetic fields such as those found in the vicinity of machinery or loudspeakers e the camera must not be directed into the sun as this can destroy the sensor e the camera may not be installed on unstable surfaces Unpacking While you are unpacking the device please handle it with utmost care 24 Table of contents a a T 8 9 Mendo THT 26 SCOPE Ea T T errui E E E EE AA ES E EE S tor EEA E 26 Features and KT oals spinoase aaia aE 26 DEVICE GESCHONKEN 27 w OTA ON TELS MIONO saer HH 27 EZ Read ol THN MONLO ast ele dns celta celeste scree nna Mclean pee cel ecg Cates cele gs dese dee 28 A3 Montor COMMCCU ien 28 44 FAINT AOS ey eiie 29 45 Gable COPING C en asesier ni sontsesiaarsanconsinesiaraniteiry AE A EAREN NAE deonsaesaeancdenteseaneesrsmnntees 29 SIRS Fel ARNO Etec aH mme enc eete noe asad EEE E a 30 5 1 Pairing Tale elne and B e a 30 9 2 Meling MNS CANCE T 30 vO tS ANIMS MONO seror E E E ORS 31 OO aise we OEE E E E E O E IEE 32 CA CNE VEW EA O E O EEA E 32 Se Ma 51T 33 LEE le AAA E A T OAN A N AT 34 ST Record Se INS sirimiri neninn cine SE EAEEREN A DIRE SEER SARATE ARES AROSIDA 35 591 Td e A A P E EE E oeau stim aetanoseaiostaesea unas E E EE 36 6 6 System SING T oF Maintenance and cleaningd ssssssssssssssssssssssssesssssssessssseeeeene ennenen ennenen ennenen neee 39 Fe OG ANT ANN TTT 39 EAE UN eects E ec cle E E E wales E T E sane credo yates E A A 39 BIL a a a aea aaa EE E

User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents