User`s manual
Contents
1. re quires servicing return it to the dealer you purchased it from packed in the original box along with the purchase invoice The warranty covers manufacturing defects with the exception of any other damage resulting from e An accident Negligent use Poor handling Bad installation and or failure to comply with the instructions in the present manual Any servicing carried out by a non authorized personnel Damage during transport the damage will not be covered by the transporter unless you express the usual type of legal reservation indicating any damage on delivery NOTICE 140X140 12 PAGES UK indd 11 26 06 14 16 52 1 IMPORTANT CUSTOMER CARE SAFETY INSTRUCTIONS IMPORTANT Please read all instructions before proceeding If you have any questions about the operation or use of this product please contact your dealer PRODUCT SAFETY This unit was designed and manufactured to ensure personal safety Impro per use can result in potential electrical shock or fire hazards Please retain these instructions for future reference The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of non isolated dangerous voltage within the product s enclosure that may be of sufficient magnitude to consti tute a risk of electric shock CAUTION Risk of electric shock Do not open CAUTION To prevent the risk of electrical shock do not remove enclosure or disas semble No u2. MYAMpP Dey vy Wry MI mu MUO My MA User s manual MmicromeGcA NOTICE 140X140 12 PAGES UK indd 1 26 06 14 16 52 AUDIOPHILE INTEGRATED AMPLIFIER Dear customer Thank you for purchasing a Micromega product This unit provides ease of use and sonics of the highest quality Please pay close attention to this instruction manual and read it fully before attempting to operate It is designed to ensure that you maximise your pleasure of listening to MyAMP Checking Check that the carton has no damage Should you have any doubt about its condition please do not hesitate to contact your dealer Opening the box you should find C5 power chord e Remote control handset and one CR2025 Lithium battery do not forget to remove the plastic protection for your battery Mains voltage MyAMP mains power supply is designed to match the following mains voltage and frequency range 85 150 Vac 47 63 Hz or 180 265 Vac 47 63 Hz Please check that the voltage indicated on the label located above the ac inlet of your unit matches your home mains voltage If not DO NOT PLUG THE AC MAINS CHORD and get in contact with your dealer In any case you will not be able to change MyAMP ac mains voltage by yourself Interconnect cables Except for the mains power chord MyAMP is supplied without interconnect cables To get the most out of your unit we strongly recommend to use good quality inter connect cables MyCABLE offers a range of cable
3. O K 4 Q RIGHT LEFT PINN oes g h d 6 Q R Q No _5 No No O T l phone Smartphone Enceinte Speaker NOTICE 140X140 12 PAGES UK indd 6 26 06 14 16 52 t Sat receiver player JO j Ordinateur Computer C OUT SUB OUT NOTICE 140X140 12 PAGES UK indd 7 26 06 14 16 52 Operation MyAMP can be controlled by the three tact switches located at the bottom right hand side of the front panel or by the remote control handset supplied with the unit A short pressure on the unit SEL key or Standby button of the remote control handset takes MyAMP out of Standby mode A 15 seconds waiting period has been implemented to allow the complete stabilization of the internal circuitry as well as perfect silent operation During this period where the red Standby led is blinking slowly no operation is allowed Once out of standby the mute led goes off and the unit selects AN1 or the latest selected source before going into standby with the volume set to a minimal level A long pressure more that 2 seconds on the SEL key or a short press on the Standby button of the remote control handset places MyAMP in Standby mode again You can select the proper volume level by pressing on the VOL and VOL keys on the unit on the remote control handset A long press on each volume key gives you the possibility to increase or decrease rapidly the volume When increasing rap
4. h module is only powered when selected avoiding any interaction between analog and digital signals You will need to connect your Bluetooth device to MyAMP again when you select the Bluetooth input NOTICE 140X140 12 PAGES UK indd 9 26 06 14 16 52 Below you will find a shortlist of MyAMP Bluetooth status indications Bluetooth Leds Status Blue led ON 2 sec OFF 1 sec There is no Bluetooth unit connected to MyAMP Blue and Red leds blink alternatively MyAMP is in Pairing mode Blue led flashes every 2 seconds A Bluetooth device is connected to MyAMP Red led flashes 5 times on the row Module memory has been cleared Blue led ON MyAMP is receiving music TECHNICAL CHARACTERISTICS Audio characteristics Analog Inputs Coaxial SPDIF input Optical SPDIF input USB input Bluetooth aptX Module SPDIF sampling frequencies USB sampling frequencies USB SPDIF BLUETOOTH resolution Max Bluetooth sampling frequency Bluetooth pairing capacity Power 8Q Power 4Q Recommended load impedance THD Noise 10W 1 kHz 8Q Damping factor Alimentation lectrique Type of mains cord Mains voltage range Mains frequency range Standby power consumption 85 265 Vac Dimensions Unit L x P x H mm Packaging L x P x H mm Poids Unit Packaging NOTICE 140X140 12 PAGES UK indd 10 3 x 250mV 1M9 1 x gt 0 2v p p 759 1 x Toslink 1 x class1 0 BT 3 0 32 kHz 192
5. idly the ramp will stop at a predefined level loud enough but not too loud to damage any speaker Once that level is reached if you want to increase the volume you will have to do it step by step To select another source than the selected one press on the SEL key of the unit until the desired source is reached or use the direct access keys of the remote control handset Each time a source is changed MyAMP goes into mute for 500ms to avoid any switching noise When selecting a digital source MyAMP will unmute when a correct digital stream is re ceived Otherwise the unit will stay muted with the red mute led on and no change in the previous volume setup possible to avoid unexpected level changes Bluetooth input apt BA MyAMP is equipped with an aptX Bluetooth module CSR NOTICE 140X140 12 PAGES UK indd 8 26 06 14 16 52 The Bluetooth input is indicated on MyAMP front panel by a Bluetooth logo framed by two leds a red one on the left side and a blue one on the right When selecting the Bluetooth input for the first time MyAMP is in pairing mode the red and blue leds will flash alternatively You should now be able to see MyAMP in the list of Bluetooth units on your Bluetooth device Connect your device to MyAMP following your device connection procedure Once connected MyAMP front panel indicator will change status the red led will switch off and the blue led will flash every 2 seconds From your Bluetooth device you can
6. kHz 44 1 kHz 96 kHz 16 24 bits 48 kHz 8 30 W 60 W gt 4Q lt 0 003 gt 100 up to 1kHz C5 85 150 V ac or 180 265V ac 47 63 Hz lt 500 mW 140 x 165 x 75 325 x 210 x 150 1kg 1 5 kg 26 06 14 16 52 Cleaning of the unit 1 Unplug MyAMP from AC mains 2 Using a soft cloth gently wipe out the dust from MyAMP surfaces To avoid any damage to the product never use any solvent or cleaning product containing solvent such as acetone trichloroethylene Never use any abrasive material to clean MyAMP 3 Once MyAMP has been cleaned you can connect the unit to the AC mains again Working conditions Working temperature from 0 35 C 32 95 F Storage temperature from 25 60 C 13 140 F Relative humidity working from 20 a 80 Relative humidity storage from 10 90 without condensation Warning To reduce the risk of fire or electrical shock do not expose MyDAC to rain or moisture Recommendations Do not use MyAMP near water Do not place objects filled with liquid on or near MyAMP Do not place MyAMP near any heat sources such as radiators stoves or other heat generating products including open flames Disconnect MyAMP during lightning storms or when unused for extended periods Refer all service related issues to qualified personnel WARANTY Your MyAMP is covered by a one year warranty from the date of purchase f the device
7. lso used as remote control reception indicator NOTICE 140X140 12 PAGES UK indd 4 26 06 14 16 52 Front panel description On the left hand bottom side of the front panel you will find the MyAMP logo with the red Standby led located just below In the middle of the unit from bottom to top you will find the 3 5mm headphone jack with the IR received just above and a vertical row of 10 leds The first led just avove the IR receiver is the red Mute led Then 8 white leds indicate the volume level and finally at the top of the row another red led indicate clipping when blin king and maximum level when always on On the right side of the front panel from bottom to top there are 3 control tact switches SEL VOL and VOL Three white leds indicating analog input selec tion AN1 AN2 and AN3 are located above the tact switches and then three other white ones used to indicate digital input selection USB OPTO and COAX Finally at the top of the right side of the front panel a Bluetooth logo is framed on the left by a red led and on the right side by a blue one Please read the Bluetooth paragraph for more details about MyAMP bluetooth input NOTICE 140X140 12 PAGES UK indd 5 26 06 14 16 52 Exemple de sch ma de raccordement Recepteur sat Sal CD DVD BD playe Digital Outputs Tuner FM Io Digital Oy Ts REC OUT SUB dB gt
8. omes independent from the loudspeakers one NOTICE 140X140 12 PAGES UK indd 3 26 06 14 16 52 MyAMP power amplifiers operate in class AB thus needing a heatsink MyAMP is cooled by forced convection thanks to an extremely quiet fan and a proprietary extrusion profile designed by Micromega This profile can be seen on each side of the unit Despite the fact that MyAMp is fully protected against abnormal heatsink temperature rise it is strongly recommended to allow 10cm minimal free space on the left and right sides of the unit This way the air flow from left to right will not suffer any constraints You can install MyAMP in a closet as long as it is equipped with air input and output with sufficient surface and a good ventilation to avoid any air temperature rise that would trigger MyAMP over temperature protection system The following diagram gives you an example how to connect different units to MyAMP Powering up Once having connected all your system units to MyAMP you can now plug in the ac line chord supplied with the unit MyAMP is now in Standby mode indicated by a red led located below the MyAMP logo on the bottom left hand side of the unit front panel MyAMP meets the latest environment energy regulations and requires less than 500mW in Standby mode making unnecessary the use of a power switch removing the electrical stress at each turn on and off will lengthen the life of com ponents The stanby red led is a
9. s matching perfectly with MyAMP quality requirements We offer short cables especially designed for My products as well as Loudspeakers cables designed as the perfect complement of MySPEAKER the best match loudspeakers to MyAMP NOTICE 140X140 12 PAGES UK indd 2 26 06 14 16 52 Wiring MyAMP has 3 line level analog inputs AN1 AN2 and AN3 one USB 24 96 digital input and two 24 192 SPDIF coaxial and optical inputs Beside MyAMP is equipped with an aptX Bluetooth module with outstanding sonic performance A pairing switch located on the back panel of the unit allows connecting many different Bluetooth devices giving each one the possibility ot listening to its own music on MyAMP A SUB output gives you the possibility to add an active subwoofer to your system if needed The RECORD ouput sends the analog signal content just before the volume control to and external device such as a recorder or a processor MyAMP has also a trigger input to control the Standby On status of the unit by a 5 to 12V DC trigger voltage On the same connector you can also send from an external system RC5 remote control codes to access directly all MyAMP functions The TRIG IR IN connector wiring diagram as well as the list of remote control codes is available on our web site under MyAMP Support On MyAMP front panel your will find a 3 5mm headphone socket When inserting a headphone jack the loudspeakers are muted and the headphone volume control setup bec
10. ser serviceable parts inside Refer servicing to qualify service personnel The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating maintenance and servicing instructions in the literature associated with this device AUDIS sarl 13 15 rue du 8 Mai 1945 94470 Boissy Saint Leger FRANCE Fax 33 0 1 4382 6128 www micromega hifi com VAT FRO7500331301 NOTICE 140X140 12 PAGES UK indd 12 26 06 14 16 52
11. start sending music to MyAMP As soon as MyAMP will receive a valid data stream the front panel blue led will stop blinking and will stay on as long as MyAMP receives music You can connect up to 8 different Bluetooth units to MyAMP actually allowing every member of the family to listen to its own music To connect a new device to MyAMP you must enter pairing mode first To access pairing mode a microswitch is located on the back panel of the unit indicated by BT PAIR Using a toothpick or any similar object press at least 2 seconds on the pairing switch On the front panel the red and blue leds will flash alternatively indicating that you have entered pairing mode You should be able now to see MyAMP in the list of Bluetooth devices on your Bluetooth unit Connect your device to MyAMP following your device connection procedure Once connected MyAMP front panel indicator will change status the red led will switch off and the blue led will flash every 2 seconds Once 8 devices have already been paired to MyAMP if you try to pair an additional device the first one that was paird to MyAMP will be erased and replaced by the new one You can always decide to erase the list of devices that were connected to MyAMP Bluetooth module To do so you need to press the pairing switch for more that 10 seconds and the Red led will blink 5 times on the row indicating that the memory was erased To guarantee MyAMP musical reproduction integrity the Bluetoot
Download Pdf Manuals
Related Search