Operation Manual ()
Contents
1. Click Next to continue Page 25 Larsen amp Brusgaard If Windows XP is configured to warn when unsigned non WHQL certified drivers are about to be installed the following screen will appear unless installing a Microsoft WHQL certified driver Click on Continue Anyway to continue with the installation If Windows XP is configured to ignore file signature warnings no message will appear The following screen will appear as Windows XP copies the required driver files Tuesday May 18 2010 LogTrackll Operating manual Hardware Installation The software you are installing for this hardware USB Serial Converter has not passed Windows Logo testing to verify its compatibility With Windows AF Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway Hardware Update Wizard Please wait while the wizard installs the software SZ USB Serial Port a ftseruiz dll To CN DOW S systems2 Page 26 Larsen amp Brusgaard LogTrackll Operating manual Windows should then display a Found New Hardware Wizard message indicating that the installation was successful Click Finish to complete the install2. Current Barometric Pressure Mbar Current X value OT f Fa 09 ixe H fey Current Y Value D Bze This window consists of the following Current X Value Current Barometric Pressure This is also the Ground Level pressure when calculating the altitude after take off Current X Y and Z value The values are bit values where bit 4mg In the LogTracklI Data Analysis software all recorded 3 axis acceleration data are shown as g Force values within the range 16g To view the Start Stop logging trigger altitudes press and hold Stop Logging Altitude LogTrackll will switch between the start and stop logging trigger altitude heights In this screen example LogTrackII will automatically start logging at 12000 feet and stop logging at 1000 feet To change the altitudes or switch to feet meters please read section Change Trigger Altitudes NOTE If no button has been pressed within 30 seconds LogTrackll will return to Standby Mode showing Current Barometric Pressure Date Time seconds and Device ID To enter the Main window from Standby Mode press Tuesday May 18 2010 Page 10 Larsen amp Brusgaard LogTrackI Operating manual 8 Standby Mode Battery Status me Current Barometric Pressure j i d i 7 Current Date TIME ri H 5 9 3 Current Time Device ID 4 3 1 8 Current Seconds Battery Status Full capacity Symbol shows two black bars inside the batt
3. Continue Anyway to continue has not passed Windows Logo testing to verly its compatibility with the installation If Windows With Windows AF Tell me why this testing is important XP is configured to ignore file Continuing your installation of this software may impair signature warnings no message will or destabilize the correct operation of your system either immediately or in the future Microsoft strongly appear recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway Tuesday May 18 2010 Page 29 Larsen amp Brusgaard LogTrackll Operating manual The following screen will be r displayed as Windows XP copies Hardware Update Wizard the required driver files Please wait while the wizard installs the software USB Serial Port ftserunz dll To CN DOW S systems2 Back Next gt Cancel Windows should then display a message indicating that the installation was successful Completing the Hardware Update Click Finish to complete the Wizard installation for the second port of the device Hardware Update Wizard The wizard has finished installing the software for F USB Serial Fort Click Finish to close the wizard Cancel Tuesday May 18 2010 Page 30 Larsen amp Brusgaard Open the Device Manager located in Control Panel System then select the Hardware tab and click Device Manger and sel
4. from Standby Mode press EI then press and hold EP until the unit beeps and altitude in feet meters is shown If no altitude change is detected by the unit within 30 seconds LogTrackll will return to Main Window Tuesday May 18 2010 Page 12 Larsen amp Brusgaard LogTrackll Operating manual 10 Start Stop logging The LogTrackll can begin logging automatically or manually The LogTrackII can handle up to 100 separate log files up to a total of 8 hours of logs When downloading into the LogTrackllI Data Analysis software each log is created with a filename including Date Time and Device ID Automatic Start and Stop If the start logging trigger altitude are not 0 the LogTrackll will automatically start and stop logging at the preset height Logging will start automatically from any mode NOT OFF with no user input required Logging Active Current Altitude When LogTrackll passes the start logging trigger altitude the device will sound one beep show Logging on the display and begin logging the altitude and 3 axis data When LogTrackll passes the stop logging Trigger altitude the device will sound one beep switch off Logging on the display and stop logging Manual Start and Stop At any time on the ground or in the airplane Manual Start Stop is possible IF the Start logging trigger altitude are set to 0 Start First enter Jump Mode The LogTrackI shows Altitude Then Pres
5. 2010 Page 19 Larsen amp Brusgaard LogTrackll Operating manual The OS comes up with a Found New Hardware 1 Update Driver Software USB Serial Port Wizard which guides you through the installation How do you want to search for driver software procedure Select the option Browse my computer for driver gt Search automatically for updated driver software Windows will search your computer and the Internet for the latest driver software software en shown right screen for your device unless you ve disabled this feature in your device installation shot settings gt Browse my computer for driver software Locate and install driver software manually Cancel Browse for driver software on the CD ROM and enter the file KD L Update Driver Software TTL232R path in the combo box Z USB Drivers in the example Browse for driver software on your computer right or browse to it by clicking a Search for driver software in this location the browse button Once the file r i RIVERS COM 2 04 16 WHOL Certified COM 2 04 16 WHOL Certified path has been entered in the box a Include subfolders click next to proceed Let me pick from a list of device drivers on my computer This list will show installed driver software compatible with the device and all driver software in the same category as the device Next Cancel Tuesday May 18 2010 Page 20 Larsen amp Brusgaard LogTrackll Operating manual When the instal
6. 91 m Tolerances Below 1000 feet 300 meter 10 feet Above 1000 feet 300 meter 1 2 Date and Time Tolerances 4 min month Operating Temperature Range 30C to 60C 22F to 140F Interface Communication Micro USB for download and setup Software LogTrackII Analysis Software included on CD ROM Tuesday May 18 2010 Page 33
7. VER 2 0 aa MOCT FEACH Yp DATA ANALYSIS SOFTWAR EogTrackli Operating manual Larsen amp Brusgaard LogTrackll Operating manual Contents 1 Introduction 00 0 0 Ed RE Ed ee AR RE Ee 4 2 hnportant Jump Festing esse nee ee ae eo DE ee De ER Go ee Ee 6 I SV SIEH Requirements nee ee ee edge 6 A Package OTNC a e N EE 7 S DESCHI PL ION RE EE EO EN 8 6 Powering ON ee a EE 9 7 Na di ER N EE see een 10 Ee Pule EA De RE EE OE EE EE N N EURUEESEREREURERFSESTEEREER 11 9 JUMP N Ode eie ea ee ee ee ee EE ee de AE 12 10 Sart Slop 1025108 AE OR OO EE OE N ER OE OE OE 13 11 Changing Trigger Altitudes RR de ee ee AR RR EE ee RA 14 12 Recorded DAS ESE MEE ER Ee EE De ee GR BE Ee GE NG EEN oen ee Ge EE Ee 15 ld Dovnload ditd ee seed E ee er 15 NRS IE Ed LE AAR AO OR ER EE OR OE OE EE N OE OE AO 15 16 Resetting the Log Track ee ER ee AR RR EE 16 17 Battery replacement 0 ee ee er ee 17 18 LogTrackII Driver Installation Windows 7 Windows 7 X64 esse RE ER 18 19 LogTrackII Driver Installation Vista Vista X64 000 00 ees RE ee ee ee de ee ee ee ee AA RR EE EE ee 22 20 Log Track Driver Installation XP XP64 ee ee ee ee RR EE 24 21 1 08 Track Analysis Software ccs esse eie ae a aan 32 22 ole de Li Oe ceca ge as er N OE EE 33 Tuesday May 18 2010 Page 3 Larsen amp Brusgaard LogTrackI Operating manual 1 Introduction The LogTrackII Data Logger is a very small thin low power easy to us
8. ation for the first part of the The wizard has finished installing the software for device USB Serial Converter a Completing the Found New Hardware Wizard Click Finish to close the wizard Cancel The Found New Hardware Wizard will continue by installing the USB Serial Port driver for the second part of the device The procedure for installing the second part is identical to that of installing the first part from the first screen of the Found New Hardware Wizard Tuesday May 18 2010 Page 27 Larsen amp Brusgaard The Found New Hardware N eN Wizard will launch automatically to install the COM port emulation drivers As before select No not this time From the options and click Next to proceed with the installation Select Install from a list or Hardware Update Wizard specific location Advanced as shown below and then click Next Tuesday May 18 2010 LogTrackI Operating manual Welcome to the Hardware Update Wizard Windows wall search for current and updated software by looking on pour computer on the hardware installation CD or on the Windows Update Web site with your permission Read our privacy policy Can Windows connect to Windows Update to search for software CO Yes this time only O Yes now and every time connect a device No not this time Click Next to continue This wizard helps you install software for USB Seral Converter Fa If your hardware ca
9. connect a device Click Next to continue Page 24 Larsen amp Brusgaard Select Search for the best driver in these locations and enter the file path in the combo box Z USB Drivers in the example right or browse to it by clicking the browse button Once the file path has been entered in the box click next to proceed Select Install from a list or specific location Advanced as shown to the right and then click Next Tuesday May 18 2010 LogTrackll Operating manual Hardware Update Wizard Please choose your search and installation options Search for the best driver in these locations Use the check boses below to limit or expand the default search which includes local paths and removable media The best driver found will be installed Search removable media floppy CO ROM Include this location in the search ZAUSB Drivers vw Don t search will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware Hardware Update Wizard This wizard helps you install software for USB Seral Converter Ce If your hardware came with an installation CD lt 3 or floppy disk insert it now What do you want the wizard to da Install the software automatically Recommended Install from a list or specific location Advanced
10. e device for measuring barometric pressure altitude and g Force data LogTrackI can be set to activate deactivate at different trigger altitudes and can automatically store up to 100 separate jumps or up to 8 hours of recording time without any user input This ultra low power consumption device is specifically designed for skydiving canopy flight testing and other pressure relevant environments and applications LogTrackII comprises a 16 g force 3 axis high resolution accelerometer data recorder LogTrackII is the perfect data logger where G forces need to be examined relative to barometric pressure and altitude Among the features are 16 g force 3 axis high resolution accelerometer Barometric pressure sensor Large storage capacity up to 8 hours recording time Durable rubberized coating Super thin curved design USB port for connection to PC using LogTrackII Data Analysis software Long lasting easy to find batteries On off mode Built In mounting holes for various pilot placements Tuesday May 18 2010 Page 4 Larsen amp Brusgaard LogTrackll Operating manual Using the LogTrackI Data Analysis software recorded data can be downloaded to a PC All information logged by the unit can be displayed in a fast clean and concise charting format and can be archived for later data research and comparison ID Lop Track Analytic Software from Larsan Hrucpaard c documante and cottings eteffonidecktoploptrack daland filerihr
11. ect View gt Devices by Type the device appears as a USB Serial Converter with an additional COM port with the label USB Serial Port Tuesday May 18 2010 LogTrackII Operating manual 2 Device Manager File Action View Help gt 5 p STEFFEN PC s y Computer H Disk drives i B Display adapters 24 DYDICD ROM drives Floppy disk controllers i A Floppy disk drives H a Human Interface Devices IDE ATASATAPI controllers Gea IEEE 1394 Bus host controllers a Keyboards i T Mice and other pointing devices 3 Monitors Sa Multi port serial adapters Ea Network adapters H NVIDIA Network Bus Enumerator Ports COM amp LPT i EN MSP FET43OUIF Serial Port COM Processors 4 SCSI and RAID controllers Sound video and game controllers 99 System devices Universal Serial Bus controllers Aladdin HASP Key Aladdin USB Key Generic USB Hub SafeNet USE SuperPro UltraPro Standard Enhanced PCI to USB Host Controller Standard OpenHCD USB Host Controller USE Composite Device LSB Root Hub en 7 USB Serial Converter Page 31 Larsen amp Brusgaard LogTrackI Operating manual 21 Log Track Analysis Software Using the LogTrackll Data Analysis software recorded data can be downloaded to a PC All information logged by the unit can be displayed in a fast clean and concise charting format and can be archived for later data research and c
12. ery icon Half capacity Symbol shows one black bar inside the battery icon Low capacity Symbol shows no black bars just an empty battery icon Batteries should be replaced as soon as possible if low capacity displays Current Barometric Pressure This is also the Ground Level pressure when calculating the altitude after take off Current Date Can only be changed from the LogTrackII Data Analysis PC software Current Time Can only be changed from the LogTrackII Data Analysis PC software Current Seconds Can only be changed from the LogTrackII Data Analysis PC software Device ID Used to identify the device This number can only be changed from the LogTrackII Data Analysis PC software NOTE To enter the Main window from Standby Mode press The LogTrackll automatically switches OFF 14 hours after entering Standby Mode Tuesday May 18 2010 Page 11 Larsen amp Brusgaard LogTrackll Operating manual 9 Jump Mode Shortly after take off the current barometric pressure will switch to current altitude in either feet or meters indicating that the unit has switched to Jump Mode oe En _ i f Current Altitude exc SES lt lt ss EI OD fU C3 N lt x O 4 Jump Mode is required before automatic or manual logging NOTE To enter Jump Mode from Main Window press and hold EP until the unit beeps and altitude in feet meters is shown To enter Jump Mode
13. lation has finished a completion screen is N Update Driver Software USB Serial Port COM3 displayed Windows has successfully updated your driver sottware Windows has finished installing the driver software for this device Click on Close to finish the driver installation _ USB Serial Port Close Tuesday May 18 2010 Page 21 Larsen amp Brusgaard LogTrackll Operating manual 19 LogTrackII Driver Installation Vista Vista X64 Connect the device to a spare USB port on your PC Windows Found New Hardware Wizard will launch The OS comes up with a Found New Hardware Wizard which guides you through the installation procedure Select the option Locate and install driver software recommended Insert the CD ROM with the LogTrackll drivers and click on Next Tuesday May 18 2010 Found New Hardware Windows needs to install driver software for your FlyTrack Locate and install driver software recommended Windows will guide you through the process of installing driver software for your device gt Ask me again later Windows will ask again the next time you plug in your device or log on Don t show this message again for this device Your device will not function until you install driver software KS Found New Hardware FlyTrack Insert the disc that came with your FlyTrack If you have the disc that came with your device insert it now Windows will a
14. me with an installation CD lt or floppy disk insert it now What do vou want the wizard to da Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Page 28 Larsen amp Brusgaard LogTrackll Operating manual Select Search for the best AmE E driver in these locations and l l l Please choose your search and installation options nt enter the file path in the combo box Z USB Drivers n the example right or browse to it by Search for the best driver in these locations clicking the browse button Once Use the check boxes below to limit or expand the default search which includes local the file path has been entered in the box click next to proceed Search removable media floppy CO ROM Include this location in the search paths and removable media The best driver found will be installed USB Drivers Ww Don t search will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware If Windows XP is configured to warn when unsigned non WHQL certified drivers are about to be installed the following screen will Hardware Installation The software you are installing for this hardware appear unless installing a Microsoft USB Serial Converter WHOL certified driver Click on
15. omparison Among the features are Displays barometric pressure altitude and 3 Axis g force data over time in chart View raw or filtered data Zoom to the finer details in the graphical data chart Fully printable charts Automatic scale can be activated or deactivated Date can be exported for other uses as well as shared with other LogTrackI users Log Track Analysis Software from Larsen A Grospaard c idocumonts and gettingeieteffonidesktopllogtrack doland fMeribrosgaard logtrack deland Morkeplit Mlerids 03 3010 171477 did tet Eie Logie Communicstor View Geb Hein oe EA n Au Fe GeForce teer F Erabi Apsua Filter fier Erd Vad of Fir Chakaihar Fer Orks Fler 2k SP 12151EPM PSO TEP PSP PRS Pe TITAS TRI Term Ta Ta eS Pd HER U ARGS 1 307 RES Fier 1 410 Akiu Fiar D50 Please read the LogTrackII Analysis Software User Manual for more information Tuesday May 18 2010 Page 32 Larsen amp Brusgaard LogTrackll Operating manual 22 Specifications Mechanical Dimensions 52 x 40 x 12 mm 2 16 x 1 57 x 0 47 inches Weight 30 grams 1 05 oz Battery type 2 x CR 2325 or equivalent Battery Life 1 2 years depending on usage Data logger Storage capacity 8 hours 8000 pages Continued storage of 100 separate logs Accelerometer 3 axis accelerometer Sampling rate 48Hz Measurement range X Y and Z 16g Accuracy 50mg Altimeter Sampling rate 4Hz Maximum logging altitude 39 999 feet 12 1
16. orded pages LogTrackII can store up to 8 hours of data 8000 pages in max 100 separate log files To view how many total pages are stored on the device please read section Change Trigger Altitudes 13 Auto OFF The LogTrackll automatically switches OFF 14 hours after the last jump or 14 hours after last pressing any key whichever comes first NOTE When switched OFF the LogTracklI cannot be used for jumping Customer settings log data and clock are not lost when switched OFF To power the LogTracklI on see section 6 Power On 14 Download data In Standby Mode or Main Window plug the Micro USB cable into the LogTrackII and connect to PC USB port In the LogTrackI Data Analysis software application the device will show 15 Delete data Either Reset the LogTrackll See section Resetting the LogTrackII while pressing B down Keep Bi pressed for about 5 seconds until 5 beeps are completed LogTrackII recorded data is now delete Or Delete recorded data from the LogTrackI Data Analysis PC software application Note CAUTION After deleting data there is no way to restore data Tuesday May 18 2010 Page 15 Larsen amp Brusgaard LogTrackII Operating manual 16 Resetting the Log Track Reset Press a paperclip into the tiny hole on the rear side of the unit and release The unit will restart NOTE Reset the unit after battery replacement and when troubleshooting Customer setting
17. r software gt Search automatically for updated driver software Windows will search your computer and the Internet for the latest driver software for your device unless you ve disabled this feature in your device installation settings Browse my computer for driver software Locate and install driver software manually Cancel Update Driver Software TTL232R Browse for driver software on your computer Search for driver software in this location RIVERS COM 2 04 16 WHOL Certified COM 2 04 16 WHOL Certified Include subfolders Let me pick from a list of device drivers on my computer This list will show installed driver software compatible with the device and all driver software in the same category as the device Next Cancel Page 18 Larsen amp Brusgaard When the installation has finished a completion screen is displayed Click on Close to finish the driver installation di J Fi LogTrackll Operating manual Update Driver Software USB Serial Converter Windows has successfully updated your driver software Windows has finished installing the driver software for this device USB Serial Converter The Found New Hardware Wizard will continue by installing the USB Serial Port driver for the second part of the device The procedure for installing the second part is identical to that of installing the first part from the first screen of the Found New Hardware Wizard Tuesday May 18
18. s and PP down and wait for 5 beeps and the Logging icon will show Stop Press SU and PP and wait for 5 beeps and the Logging icon will switch off Note When the Logging icon shows the unit is logging data and an automatic or manual stop is required to stop logging Tuesday May 18 2010 Page 13 Larsen amp Brusgaard LogTrackll Operating manual 11 Changing Trigger Altitudes mr ET mm LLL 01de 09 1 Oe _ 00 iey 8 248 zo 1 Press H and release quickly The I icon will turn on and off disappear When the I icon appears again immediately press B ana keep it pressed The I icon will disappear again 3 When the I icon appears again release a immediately ks EF Factory ID l The LogTrackII now flashes in the Start Trigger Altitude ar EI Start Logging Altitude Fest 9 Stop Logging Altitude Pages recorded Hi evice ID PE 2 Press Tor Po change Start Trigger Altitude 3 Press H again and the Stop Trigger Altitude flashes 4 Press WE or ad to change Stop Trigger Altitude 5 Press H again and the Feet Meters icon flashes 6 Press WW or gt to change between Feet Meters J Press H again to leave Change Trigger Altitude Note If setting Start trigger altitude to 0 Automatic Start and Stop is disabled and only manual start stop is possible Tuesday May 18 2010 Page 14 Larsen amp Brusgaard LogTrackll Operating manual 12 Rec
19. s and recorded logs are kept protected in the unit memory when removing batteries However the built in clock may again need to be set to the correct time Tuesday May 18 2010 Page 16 Larsen amp Brusgaard LogTrackII Operating manual 17 Battery replacement Screw Carefully remove screw from battery cover and remove batteries Install new batteries and note polarity Use only CR 2325 or equivalent NOTE Reset the LogTrackll after replacing batteries Customer settings and recorded logs are kept protected in the unit memory when removing batteries However the built in clock may again need to be set to the correct time Tuesday May 18 2010 Page 17 Larsen amp Brusgaard LogTrackll Operating manual 18 LogTrackII Driver Installation Windows 7 Windows 7 X64 Connect the device to a spare USB port on your PC Windows Found New Hardware Wizard will launch The OS comes up with a Found New Hardware Wizard which guides you through the installation procedure Select the option Browse my computer for driver software as shown in the right screen shot Browse for driver software on the CD ROM and enter the file path in the combo box Z USB Drivers in the example shown right or browse to it by clicking the browse button Once the file path has been entered in the box click next to proceed Tuesday May 18 2010 Update Driver Software USB Serial Port How do you want to search for drive
20. tual canopy opening deployment 3 System Requirements Windows XP XP64 Vista Vista x64 Windows 7 Windows 7 x64 CD ROM drive One unoccupied USB port on your PC Tuesday May 18 2010 Page 6 Larsen amp Brusgaard LogTrackll Operating manual 4 Package Contents Unpack the package and inspect all the items carefully If any of the items are damaged or missing or if you have any questions please contact Larsen amp Brusgaard LogTrackll device 100cm Micro USB to USB cable for desktop PC LogTrackll Data Analysis software PC CD ROM F r Fe With Tuesday May 18 2010 Page 7 Larsen amp Brusgaard LogTrackll Operating manual 5 Description 1 LCD display 2 Left button 3 Middle button 4 Right button 5 Micro USB jack Tuesday May 18 2010 Page 8 Larsen amp Brusgaard LogTrackll Operating manual 6 Powering ON The LogTrackll has been powered OFF prior to shipping from our factory To power ON press and hold any key until the LogTrackII beeps then release the button The LogTrackll runs a self test and displays all icons Current Pressure Factory ID 1 Factory ID 2 Firmware Version Note If factory ID 1 is not 229 and if factory ID 2 is not 31 the unit is defective and must be returned to L amp B It then switches to a screen display referred to as the Main Window Tuesday May 18 2010 Page 9 Larsen amp Brusgaard LogTrackll Operating manual 7 Main Window
21. ucpaard loptrack deland filerteplit filar6 03 2010_13 14 37_d41 10 Ele Logtredkt Communicator Yew Setup Piek omy eit n Ahde i Fii G Force k Fii Ina amp Frere Orden 7 Fegi F Fig Uic l 040 Fer Chekas Fiter iris reke 30 8 1214 TT PM TEA 121315FM 121540 PM TIP 127 SOP PIS TE 2PM 1216 NOPM 1203S 121400PM 121823 PM 121450 Eis FM aT U RES 1 377 RES Fiter 1 410 Akinsde Fie 250 Tuesday May 18 2010 Page 5 Larsen amp Brusgaard LogTrackI Operating manual 2 Important Jump Testing Larsen amp Brusgaard strongly recommends users of LogTrackII to make some practice test jumps with the LogTrackII before using it for specific project related tests This way the users can familiarize themselves with the LogTrackII unit and the LogTrackll PC software before spending time and money on business specific tests The LogTrackI may be put anywhere on the skydiver s body However the closer the unit is placed to the torso the more accurate the g force measurements will be Based on many test jumps Larsen amp Brusgaard does not recommend placing the LogTrackll on the hand or the arm due to movements and differences in air pressure Different hand arm positions will not accurately record G force data or the area of actual canopy opening deployment Placing the Log Track on the helmet will give more reliable data but again the head can also make movements and result in inaccurate readings of G force data and the area of ac
22. utomatically search the disc for driver software Page 22 Larsen amp Brusgaard LogTrackll Operating manual When the installation has finished a completion screen 1S Koy Wo Found New Hardware USB Serial Converter displayed The software for this device has been successfully installed Click on Close to finish the Windows has finished installing the driver software for this device driver installation LSB Serial Converter The Found New Hardware Wizard will continue by installing the USB Serial Port driver for the second part of the device The procedure for installing the second part is identical to that of installing the first part from the first screen of the Found New Hardware Wizard Tuesday May 18 2010 Page 23 Larsen amp Brusgaard 20 LogTrackII Driver Installation XP XP64 LogTrackll Operating manual Connect the device to a spare USB port on your PC Windows Found New Hardware Wizard will launch Select No not this time from the Mb AE options available and then click Next to proceed with the installation Tuesday May 18 2010 Welcome to the Hardware Update Wizard Windows will search for current and updated software by looking on pour computer on the hardware installation CD or on the Windows Update Web site with your permission Read our privacy policy Can Windows connect to Windows Update to search for software Yes this time only i Yes now and every time
Download Pdf Manuals
Related Search